C/o Patient Building in Shillong.

Amount

Civil Work

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto1.5 m.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.All kinds of soil

Extra for every additional lift of 1.5 m or part there of in.All kinds of soil.1.5m to 3.0m

Extra for disposal of excavated earth for additional lead beyond 50m or part thereof upto 9 such additional leads. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Supplying and filling in plinth with river sand under floors including, watering. ramming consolidating and dressing complete.

Providing and laying boulder pitching under foundation footings, bases of concrete etc. complete as per drawing and technical specifications

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 12.5mm nominal size).

Applying a coat of residual petroleum bitumen of penetration 80/100 of approved quality using 1.7kg pel square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Extra for providing and mixing water proofing material in cement concrete work @ 1 kg per 50kg of cement.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement. including Admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. M-25 grade reinforced cement concrete by using 380 kg. of cement per cum of concrete. All work up to floor V level.Foundation Footings

Columns, Pillars, Piers, Abutments, Posts and Struts.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

lintels, beams, plinth beams. girders. bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platform.

Staircases (including landing).

Reinforcedcementconcrete work in shelves upto floor two level excluding cost of centering and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20 ( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size

Providing M-30 grade concrete by using 400kg of cement per cum of concrete instead of M-25 grade B.M.C/ R.M.C..

Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Shelves (Cast in situ)

lintels, beams, plinth beams. girders. bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Staircases (including landing).

Weather shade, Chajjas, corbels etc., including edges.

Reinforcement for R.C.C. work including straightening. cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars

Brick work with best available local bricks in foundations and plinth in cement mortar 1:6 (1 cement : 6 fine sand). (for super structure)

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) :For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hingesl pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately).Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators a with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS : 1285 fixed with rawl plugs and stainless steel screws etc.

Providing and fixing glazing in aluminium door, window, ventilator shutters , Canopy and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) :With float glass panes of 5.50 mm thickness

Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete:250x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete:250x10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade wiIh necessary screws etc. c.omplete :125 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.Twin rubber stopper

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in­charge complete.255 X 19 mm

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-in-charge. Powder coated minimum thickness 50 micron aluminium

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate

Providing glass panes, with wooden fillets wherever necessary.4mm thick Glass panes weighing 10 kg./sqm.

Steel work welded in built up sections/ framed work including cutting ,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as requiredIn gratings, frames, guard bar, ladder, railings, brackets, gates ,canopy and similar works..

Fabrication, supply and installation of SS 304 grade 900mm high railing made of SS 304 grade handrail pipe of 50 mm OD and 1.6 mm thickness polished with automatic round polishing machine to get a uniform hairline finish mounted with the hel of adjustable solid neck support on balustrade of approved design at 1200mm c/c and at every turn, supporting 3 mid rails of 12mm OD and 1.6 mm thickness with the help of solid connectors of 23 mm dia holding the mid rails by M6 grub screws inserted in baluster and screwed through the baluster with M6 counter sunk screws overall mounted on SS 304 grade base plate with the help of dash fasteners to be treated with K2 solution at all welding joints and passivated.

Providing and fixing stainless steel pipes for railing ( Grade 304) railing made of Hollow tubes, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the pipes with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the walls of the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coatwith approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. b) Ornamental grill

Granite stone flooring with 18 mm thick granite (Base Rate Rs. 250/- Sqft) stone, rectangular shape, ( minimum size of stone should be 0.45 sqm and one dimension not less than 700 mm), over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete.

18mm thick Prepolished Granite (Base Rate 250/-Sqft) in skirting, Risers and dado over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement including pointing with white cement mixed with pigment matching the shade of granite stone all complete and as directed.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kgper sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying polished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete, Size of Tile 60x60 cm

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in­Charge.Granite work.

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound to IS : 2645 and approved by Engineer - in - charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75kgl sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120mm and minimum thickness at khurra as 65 mm.

12 mm cement plaster of mix:1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1 cement 4 fine sand)

6 mm cement plaster of mix:1:3 (1 cement: 3 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm.

Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Applying one coat of cement primer of approved brand and manufacture on wall surface:Cement primer.

Applying chemical resistant epoxy resin wall coating over plasetered surface including preparing of the surface, applying acrylic primer, putty and painting of approved brand and manufacture.New work (three or more coats) over and including priming coat with acrylic primer and putty.

Applying priming coat with ready mixed redoxide or zinc chromate paint of approved quality and manufacture on steel work

Making plinth protection with 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand: 6graded stone aggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron. finished with 12mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone hips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing and fixing on wall face un-plasticised Regid PVC rain water pipes with all fittings and fixing clips conforming to IS:13592 type-A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion single socketed pipes with all accessories as bend, door, horn bend,shoe etc. complete as directed :

Sanitary & Waer Supply Works

Providing & fixing water closet squatting pan( Indian W.C.Pan)with 100 mm sand cast iron P or S strap,10 Litre low level white P.V.C flushing cistern with manually controled device(handle lever) conforming to IS:7231 with all fittings&fixture complete including cutting and making good the walls & floors whereever required.White vitreous china orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous flushing cistern and C.P. flush bend with fittings & C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required:W.C. pan with ISI black solid plastic seat & lid.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:White vitreous china wash basin size 550x 400 mm with a pair of 15mm C.P. brass pillar tap.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board,610x510 mm bowl depth 200 mm.

Extra for using coloured W.C. pan instead of white W.C panOrissa pattern W.C. pan 580x440 mm

Extra for using coloured pedestal type W.C. pan (European type) with low level cistern of same colour instead of white vitreous china W.C. pan and cistern

Providing and fixing superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shape with 6 mm thick hard board backing. Rectangular shape 453x357 mm

Providing and fixing 600x120x5 mm glass shelf with edges round of supported and anodised alominium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing toilet paper holder .Vitreous china

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing and fixing water Jet Nozzle with hose pipe and haif turn CP brass angle valve to be fitted with seat cover of european water closet complete in all respect of approved quality

Providing and fixing soap tray with CP brass lid and brackets fixed to wooden cleats with CP brass screws.(Jaquar model no.1131 or equivalent model of other approved make).

Providing and fixing CP brass towel rail size of 600x20 mm of approved make complete with CP brackets fixed to wooden cleats with CP brass screws(Jaquar model no.1111 or equivalent model of other approved make)

Providing and fixing soil, waste and vent pipes.100 mm dia. Centrifugally cast (spun) iron socketed pipe as per IS:3989

150 mm dia. Centrifugally cast (spun) iron socketed pipe as per IS:3989

Providing and fixing M.S holder-bat clamps of approved design to Sand Cast iron/ cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.for 100 mm dia. pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm Sand cast iron S&S as per IS-3989

Providing and fixing plain bend of required degree.100 mm Sand cast iron S&S as per IS:3989

Providing and fixing heel rest sanitary bend.100 mm dia sand cast iron S&S as per IS-3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. 100x100x100mm sand cast iron S&S as per IS-3989

Providing and fixing single equal plain junction of required degree100x100x100mm sand cast iron S&S as per IS-3989

Providing and fixing single un-equal plain junction of required degree,100x100x75 mmsand cast iron S&S as per IS-3989

Providing and fixing door piece, insertion rubber washer 3mm thick, bolts and nuts complete 100 mm sand cast iron S&S as per IS-3989

Providing lead caulked joints to sand cast iron /centrifugally cast (spun) iron pipes and fittings of diameter:100 mm

Providing and fixing trap of self cleansing with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors100 mm inlet and 100 mm outlet :Sand cast iron S&S as per IS-3989

Cutting chases in brick masonary walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 12.5 mm nominal size) including necessary plaster and pointing in cement mortar 1:4 (1 cement: 4 coarse sand):100 mm diameter pipe

Painting sand cast iron / centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey, or buff etc. over a coat of primer (of approved quality) for new work:100 mm diameter pipe

Providing and fixing floor drain points formed out of 65 mm dia GI elbow, including with 75mm dia Stainless Steel grating with frame, embedded in floor, all complete as directed.

Providing and fixing C.P. brass bottle trap for wash basin including CP waste fittings complete 32 mm dia complete in all respect of approved quality.

Providing and fixing C.P. brass bottle trap for sinks & urinal basin including CP waste fittings complete 40 mm dia complete in all respect of approved quality.

Providing and fixing cPVC. pipes complete with cPVC fittings including painting,jointing,testing the cost of cutting the chases and making good the same for waste water disposal complete as per direction of engineer incharge.32 mm dia nominal bore (Wash basin to floor trap/floor drain)

40 mm dia nominal bore (Sink,Urinal to floor trap)

Providing and fixing Chlorinated Polyvenyl Chloride(CPVC)pipes having thermal stability for hot & cold water supply including all CPVC plain &brass threaded fittings i/c fixing the pipe with clamps at 1.0 m spacing.This includes jointing of pipes &fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints ciomplete as per direction of Engineer in charge.Internal work – Exposed on wall, 15 mm nominal outer dia pipes (SDR-11)

20 mm nominal outer dia pipes (SDR-11)

ESS Building 25 mm nominal outer dia pipes (SDR-11)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.,15 mm nominal outer dia pipes (SDR-11)

20 mm nominal outer dia pipes (SDR-11)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.External Work,25 mm nominal outer dia pipes

50 mm nominal outer dia pipes

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including, cutting and threading the pipe etc. commplete including obtaining approval for connection scheme from DJB/Municipal corporation :50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete20mm

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main 25 mm nominal bore

Providing and fixing unplasticised PVC connection pipe with brass unions:45 cm length,15 mm nominal bore

Constructing masonary chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cenment:5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard designWith F.P.s bricks

Constructing masonary chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cenment:5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard designWith F.P.s bricks

Painting CPVC/G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work15 mm nominal outer dia pipes

20 mm nominal outer dia pipes

25 mm nominal outer dia pipes

Painting G.I. /CPVC pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.25 mm diameter pipe

50 mm diameter pipe

65 mm diameter pipe

Providing and filling sand of grading zone V or coarser grade all-round the G.I./CPVC pipes in external work25 mm diameter pipe

50 mm diameter pipe

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI:12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tankTreated water Tank and Untreated water tank

Providing and fixing C.P brass bib cock of approved quality. 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser/cisterns points of approved quality conforming to IS:8931.15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to 18:8931, 15mm nominal bore..

Providing and fixing enclosed type water meter ( bulk type) conforming to IS : 2373 and tested by muncipal board complete with bolts,nuts rubber, insersions etc. ( the tail plases if required will be paid seperatly )80mm dia nominal bore

Providing and fixing PTMT ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./H.P.H.D. plastic ball.40 mm nominal bore, 206 mm long weighin not less than 690 gms

50 mm nominal bore, 242 mm long weighin not less than 1240 gms

Cutting holes upto 30x30 cm in walls including making good the same with F.P.S bricks

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof

Extra for providing wash basin mixer pillar tap in place of normal pillar tap

Extra for providing and fixing CP brass push type pillar tap of approved make and model in place of normal pillar tap.

Providing and fixing mosquito proof coupling of approved Municipal design for scour and vent pipes for RCC overhead tanks complete in all respects, 20 mm diameter

40 mm diameter

Providing & fixing 9 mm thick thermal insulation tubing of elastomeric flexible material on hot water supply/return pipes having hermetic blistered closed cell structure of expanded synthetic rubber over pipes/ fitting as per manufacturer's specifications etc.complete.15 mm to 25 mm diameter

ESS Building, 32 mm to 50 mm diameter

Providing and fixing C.P. brass Overhead (Rain Fall) shower (100mm) with arm and wall flange complete including cutting and making good the walls wherever required.

Providing & fixing solid state fully hygienic no touch hand drier of approved make rated for continuous repeat usage with solid state time delay LSF protection, with independent ambient light level & seasonal control temperatures including providing necessary C.I./M.S. brackets painted with two or three coats of enamel paint of approved shade over a coat of primer, wiring cables from drier to plug, plug tops etc. complete including cutting and making good the walls wherever required.

Supplying, fixing, testing and commissioning of storage type water heater (Geyser) etc. with Stainless steel body , copper container , automatic thermostatic control electric element, pressure release valve, M.S. nuts and bolts etc. conforming to IS: 2082, 35 Litre Capacity

25 Litre Capacity

Providing & fixing water storage cooler of approved make and brand with SS body having minimum flow rate of 40 ltrs. Per hour and storage capacity 80 ltrs. Complete in respects.(VOLTAS/ BLUE-STAR/ USHA SHRIRAM )

Providing and fixing approved make & suitable model of R.O. plant (fully automatic operation) 400ltrs. Per hour flow rate having capacity to treat the raw water and average recovery not less than 35% . The operating voltage to 230 volt AC +/- 10% alongwith required capacity pump of approved make (1HP minimum) and solenoid valves, dry run protection of pump, automatic tank level control, inbuilt auto flush timer for periodic flushing of membranes, storage tank (3.0 mm (minimum) thick S.S. 304 sheet) 1500 lts of suitable size and its supporting structure, over voltage and over current protection with switch mode power supply system complete in all respects including installation and fittings with the following provisions: (IONIEXCHANGE/ KENT/AQUAPROCESS,Pantair,INDWA,Fontus )10 micron polypropylene sediment pre filter 10 micron bacteriostatic activated carbon block on line micron filter with 5 micron ratingRequired Nos. and size of reverse osmosis memberane with 0.0001 micron pore size energy saving poly amide type UV lamp of minimum capacity 400LPM and minimum lamp wattage 15WMS powder coated/SS frame . Antiscalant dosing and acid dosing system for self flushing/cleaning.Pressure switches and gauges, pH correction dosing system, Digital TDS meter, Digital pH meter, electric panel and necessary instrumentation included Rotameter.MS structure and fibre glass sheet weather protection cover as per site condition.

Providing laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the pro-portion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.100 mm diameter

150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:100 mm diameter S.W. pipe/RCC NP2

150 mm diameter S.W. pipe/RCC NP2

Providing and fixing square-mouth S.W. gully trap grade ‘A’' complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:.150x100mm size P type, F.P.S. Bricks class designation 75

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand), R.C.C. top slab with 1:2:4 mix ( 1cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size ), foundation concrete 1:4:8 ( 1cement : 4 coarse sand : 8graded stone aggregate 40 mm nominal size ), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, and making necessary channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design. Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg):With F.P.S. bricks with class designation 75

Providing and fixing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement:4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design:With F.P.S. bricks

Constructing brick masonry open surface drain Constructionofcementconcretedrain30cmwideand23cmdeepincement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.25cm drain 30cm average depth,With F.P.S bricks

Drilling by suitable rig as per IS : 2800-1979 (percussion or combination rig ) or Reverse Rotary to suit site condition from ground level in all kind of soils and weathered rock including boulders (excluding rock ) diameter of bore 450mm including carry out hydrological survey report before boring & getting the approval based on Hydrogeological survey before start of the work.Also getting approval from local authority if any required 0-30m

Extra additional for drilling in Ordinary Rock if any found

Providing and lowering uPVC casing/housing pipe 200mm dia. with wall thickness 10 mm conforming to IS :12818 including sockets of standard design.

Providing & fixing uPVC screen/slotted pipe with 1.5 mm to 3mm (slots as per strata condition) including sockets of standard design as per IS: 12818/1992.200 mm dia uPVC socketed pipe with wall thickness 10.0 mm

Providing and fixing in position threaded iron cap with locking arrangement of approved design to prevent foreign matters getting into the bore-hole as required.

Providing and laying rounded pea gravel washed & served 3 to 6 mm nominal boreas per relevant ISI code.

Providing and laying cement concrete 1:2:4 mix for sanitary sealing of well at top.

Supplying, lowering and fixing in position reducer ,PVC bail plug with "U" hooks as per IS:2800-1964.

Development of Tubewell including testing of yield depression & quality of water (for all parameters of potable water), contractor to obtain certificate for quality for water from Competent Authority approved by client or Engineer- In -Charge.Development of Tube well by high capacity air compressor till the clear water discharge but not more than 100 hours.

Additional development of Tube well by high an over pumping unit till complete development of tube well does not clear by maximum 100 hours air compressor

Tranportation, mobilisation and demobilisation or drilling equipment and ancillary equipment to site including clearing and cleaning the site after completion of work.

Providing and fixing brass full way valve with C.I. wheel of approved make, tested to a pressure of 21 kg/sqcm.100 mm dia

Providing and fixing gunmetal non return valve of approved make tested to a pressure of 21kg/sqcm.100 mm dia

Providing & fixing G.I. pipes (heavy class)confirming to IS with special fittings in external works including earthwork ,excavationin all kinds of soil including ordinary rock,refilling, painting pipes & fitting complete in alll respects. 100 mm dia

Providing & filling sand of grading zone V or coarser grade all around GI pipe in external work,100 mm dia

Providing and installing submersible pump and electrical panel suitable for 8" dia casing of bore with SS impeller, high tensile SS shaft, copper wound squirrel cage wet type induction motor 2880 rpm, 415 V, 50 Hz,3 phase A.C. supply, conforming to ISS: 8034-1976, capacity 500 litre per minute/as per hydrogeological/yield report at 70-120 m head along with a directly coupled submersible type squirrel cage electric induction 5.0 H.P(minimum). motor suitable for operation on 400 V, 3 phase, 50 c.p.s. A.C. supply, water lubricated bearings and provided with pivoted segment type thrust bearings to withstand non-vertical lead with minimum wear and tear and duly fitted with device to take up the expansion of water with heating of motor, including supply, testing and commissioning of elctrical panel from the same manufacturer, complete with all accessories in all respects. The contractor to obtain approval for model and make of pumpset & suitable Electrical panel after having yield report of fully developed tube well and submite actual bore strata chart.1 No, DOL starter of 10 HP with thermal overload relay, Push Buttons, Single Phase Preventer and Switches etc complete as required. including supplying laying and fixing water proof PVC insulated flat submersible cable 3x10 sqmm with end termination with its accessories. complete in all respect as required.

Carrying out Electrical logging of Borewell before lowering of pipe for analysiing of water quality including Electrical logging report, calculation etc.

Designing & constructing of Perculation pit cum poerfurated well 300mm dia up to 4000mm deep , 230mm thick brick masonry work allround up to 1.5m deep witj 75 class brick in CM 1:4

Providing and lowering uPVC casing/housing pipe 200mm dia. with wall thickness 10 mm conforming to IS :12818 including sockets of standard design.

Constructing bar screen / settling tank, of size 4500x2500 mm with suitable depth up to 2mm in 1:4 Cement Mortar. Height as per site requirement in Brick masonry 350mm thick waqll up to water level and 230mm thick wall above WL and up to Gl i/c all excavation 20cm tghick bed concrete 1:4:8 ........

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.a) Ordinary Soil

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:

Reinforced work in foundation footing, bases of columns, etc. and Mass concrete excluding cost of centering and shuttering, finishing and reinforcement in M20 1:1.5:3 (1 cement :1.5 coarse Sand :3 Stone Aggregate 20 mm nominal size)

Reinforced cement concrete in wall (any thickness) including attached pillasters, buttresses, plinth and string courses, fillets etc from top of foundation up to floor two level excluding cost of centring,shuttering and reinforcement in :b)M20 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).in M20 1:1.5:3 (1 cement :1.5 coarse Sand :3 Stone Aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns, etc. for mass concrete. a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c) Suspended Floors

Reinforcement of RCC work including bending, binding and placing in position complete.a. Cold twisted Bars

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Neat cement punning.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.a) 100 mm dia SW pipes

b) 150 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 100 mm dia SW pipes

b) 150 mm dia SW pipes

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. a) M30 Grd Concrete

Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in : a) M30 Grd Concrete

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.M30 Grd Concrete

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M30 Grd Concrete

Reinforcement of RCC work including bending, binding and placing in position complete. a) Cold twisted bars.

Centring and shuttering including strutting, propping etc and removal of form work for :b) Columns

b) Walls

c) Lintels, beams, girders, bressumers and cantilevers etc.

d) Suspended floors, roofs, landings shelves and their supports balconies and chajjas (3.5m height).

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Neat cement punning

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and Code chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) M30 Grd Concrete

Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in : a) M30 Grd Concrete

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M30 Grd Concrete

b)M20 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

d) Suspended floors, roofs, landings shelves and their supports balconies and chajjas (3.5m height).

Reinforcement of RCC work including bending, binding and placing in position complete.a. Cold twisted Bars

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and Code chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design

Elecrical Works

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqmmFR PVC insulated copper conductor single core cable in surface / PVC conduit, with piano type switch, phenolic laminated sheet, suitable size recessed M.S. box and earthing the point with 1.5mm² FR PVC insulated copper conductor single core cable etc as requiredGroup "A"

Group "B"

Group "C"

Wiring for twin control light point with 1.5 mm² FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way Piano type switch, phenolic laminated sheet, suitable size M.S.box and earthing the point with 1.5 mm² FR PVC insulated copper conductor single core cable etc as required

Wiring for power plug with 2x4 mm² FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No 4 mm² FR PVC insulated copper conductor single core cable for loop earthing as required

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / ecessed steel conduit, withmodular switch, modular plate, itable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conducto rsingle core cable etc. as required.

point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminatedsheet cover in front including painting etc. as required75 mm X 75 mm X 60 mm deep Each 140

1.22.2 100 mm X 100 mm X 60 mm deep

150 mm X 75 mm X 60 mm deep

150 mm X 150 mm X 60 mm deep

180 mm X 100 mm X 60 mm deep Each 183

200 mm X 125 mm X 60 mm deep

250 mm X 300 mm X 60 mm deep

250 mm X 300 mm X 100 mm deep

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

TV antenna socket outlet

Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

8 Module (125mmX125mm

12 Module (200mmX150mm)

Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. As required.

Supplying and fixing of fan clamps.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of pre-wired,fluorescent fitting / compact fluorescent fitting of all types,complete with all accessoriesandtube/lamp etc. directly onceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of pre-wired,fluorescent fitting / compact fluorescent fitting of all types,complete with all accessories and tube/lamp etc., including supplying and fixing ball and socket arrangement, 2 Nos. Down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required

Supplying of ceiling fan of 1200mm sweep as per ISI specification of brand USHA, Bajaj, Havels, Crompton & Greaves

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying of Exhaust fan300/380 mm sweep as per ISI specification of brand USHA, Bajaj, Havels, Crompton & Greaves Upto 450 mm sweep

510 mm sweep

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

510 mm sweep

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required63 A TP&N

100 A TP&N Each 6024

125 A TP&N Each 6696

315 A TP&N Each 14484

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way , Double door

12 way , Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board ofsheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar,din bar for ounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

12 way (4 + 36), Double door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. As equired.63 Amp

Supplying, installing, testing and commissioning of following capacity End Feed Unit made of 1.6mm thick sheet steel enclosure duly painted with powder coating to existing rising mains complete with TPN disconnector FSU and HRC fuses, mounting stands, cable end box, brass compression gland, connections, earthing etc. as required600 A TPN

Earthing with G.I. earth pipe 4.5 metre long, 40 mm diaincluding accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. Each

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Extra for using salt and coke for GI or copper plate earth electrode as required

Extra for using salt and coke for Copper plate earth electrode as required

Supplying and fixing 25mm x 5mm Copper strip in 40mm dia G.I. pipe from earth electrode as required

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed /XLPE aluminium conductor cable of 1.1 KV grade as required modular base & cover plate for modular switches in recess etc.2 X 25 sq. mm

3 X 300 sq. mm

Supplying and making straight throught joint with shrinkable kit including ferrules and the other jointing material for 120 sqmm, 3 1/2 core PVC insulated UG cable for service connection.

Erection of RCC/ PCC pole strut in brick ballast and ramming the foundation including excavation and refilling and secured with holding clamps, bolts, nuts, etc. as required

Supplying, installation, testing and commissioning of Silent Type DG Sets,AMF Panel, Bus Ducting/ Cables from DG Sets to Essential Panel, Synchronizing Panel where required, DG Set enclosure room sound insulation /ventilation/ smoke exhaust as required, Earthing of DG Set system, control cabling, Fuel tank/piping, DG set Exhaust piping/ Exhaust Chimney as per CPCB norms, Civil works connected with DG Sets including Foundation as required.

Fire Fighting

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :150 mm dia Ductile Iron Double Flanged

Providing and laying D.I. specials of class K-12 suitable for push-on jointing as per IS : 9523Upto 600 mm dia

Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket :150 mm dia pipes

Excavating trenches of required width for pipes, cables etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, inlayers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed within a lead of 50 mPipes, cables etc exceeding 80 mm dia but not excedding 300 mm dia

Providing, fixing joiting and testing of Heavy (class -C) G.I. pipes as per relevant IS :1239/4736 with special accessories like tees, elbow, gesket, flanges, flanged joints, rubber insertion nuts and bolts including earth work excavatin and trenching, wrapping pipekot 4mm thick 500mm width tar based plymaric corrosion protection tape or equivalent suitable to GI/ MS pipe line including applying uniform coat of cold pipekot primer complete 1 m below the ground level, refillling in layers not exeeding 20 cm in depth consolidated each deposited layer by ramming & watering complete in all respect as pe IS : 1022 (Under ground ) 150 mm dia G.I. Pipe with flange joints (5.4 mm wall thickness)

80 mm dia G.I. Pipe with flange joints

Heavy class G.I. pipes conforming to IS with accessories like tees, elbows, flanged joints, rubber insertion, nuts, bolts or welded joints including fixing the pipe with suitable flat iron strip clamps/brackets, structural members, dash fastener , cutting hole and chases in walls, floor, R.C.C. slab etc. and making good the same, including painting pipes and fittings with a primer coat of steel primer and two coats of postal red enamel paint etc. complete as required. (All the fitting i.e. tee /elbow, Valve shall be joint the pumps will flanged joints)200 mm dia (with Flanged joints)

150 mm dia (with Flanged joints)

100 mm dia (with Flanged joints)

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Providing and fixing Single headed hydrants flanged inlet with 63 mm female instantaneous outlet of gunmetal complete with male blank caps, chains conforming to IS:5290 type A with stainless steel orifice plate (if required) to keep the pressure not more than 3.5 kg/sq.cm at any point.

Providing 63mm dia 15 m long reinforced rubber lined hose pipe conforming to IS: 636-1992 Part-II with gunmetal male & female coupling wire wound with pipe as required.

Providing and fixing 63mm dia 15 m long canvas hose pipe complete with gunmetal male & female coupling wire wound with the pipe The pipe shall confirm to IS: 4927.

Providing and fixing Gunmetal branch pipe with 20mm dia nozzle conforming to IS:903. suitable for installation connections to hose coupling etc. as required.

Providing and fixing Four way fire brigade connection housed in steel cabinet of size 900mm x 750mm x 400mm fabricated from 1.5mm thick M.S. sheet having lockable arrangement, openable glazed door with 4mm thick glass, including painting a coat of steel primer and two coats of postal red enamel paint, with necessary supports for the cabinet etc. with 150 mm dia. non return and butterfly valves complete in all respects. 4 Way - 150mm dia

Providing and fixing Set of "Siamese" quadraplet instantaneous fire brigade connections comprising of two gunmetal instantaneous male inlet coupling 63mm dia with plug and cap, chain bends, tees etc for inlet to the static tank.

Providing & Fixing 150 mm dia, 4 way suction coupling for firebrigade withdrawal of water from the fire tank

Providing and fixing glazed door shutter and frame for Fire hose cabinet with hold fasts ( frame fabricated from 40 x 40 x 5mm and shutter from angle) 2100 mm high x 1200 mm wide x 600mm deep with locking arrangement, 4mm thick glass with M.S. flats including all accessories, painting with one coat of steel primer and two coats of postal red enamel paint complete as per drawing and as directed. The words “ hose cabinet” to be painted on the box complete in all respects.

Providing and fixing Weather proof standard stand post type hose cabinet (900mm x 750 mm x 400 mm) out door type made of 1.5mm thick M.S. sheet having central opening glazed door with 4mm thick glass suitable for accommodating hydrants, 2 Nos. canvas hose pipe and branch pipe including necessary locking arrangements, painting one coat of primer and two coats of postal red enamel paint.. The shutters are to be lockable type. The words “ hose cabinet” to be painted on the box.

Providing and fixing cast iron body IS: 210 FG 220 and double flange gear simple operation type butterfly valve conforming to IS: 13095 with SS304 disc and shaft NITNLE rubber replaceable seat of the following size complete with bolts, nuts, washers and rubber insertions as per specification.150 mm dia

80 mm dia

Supplying, testing, installation & commissioning of pressure switches for pumps including necessary wiring upto the control panel.

Constructing masonry chamber 90x90x100 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.with F.P.S. bricks

Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction, spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required.36 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585 20 mm dia gun metal ball valve & nozzleDrum and brackets for fixing the equimpments on wall.Connection from riser with stop valve (gun metal) & M.S. Pipe

Providing and fixing C.I. sluice valves (With cap) of approved quality complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) Class II200 mm dia

150 mm dia

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having caliberation of 0 - 16 Kg / cm2 .

Supplying and Fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926

Supplying and Fixing vane type waterflow switch with contacts suitable for installation on 50 mm to 150 mm dia pipeline for a service pressure upto 20 Kg/sq.cm.

Providing, Fixing, Testing and Commissioning of Sprinkler Installation Control Valve of Cast iron body and brass / bronze working parts comprising of water motor, alarm, bronze seat clapper and clapper arm, hydraulically driven mechanical gong bell to sound continuous alarm when the Sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc. of size 200/150 mm dia, as required.

Supplying, Installation, Testing & Commissioning modular construction master control annciation panel for sprinkler with provision for requider No. of Zone (30% additional spares),eachsprinkler hydrant will have atleast 2 zone on each floor as approved by engineer.The panel shall have but not limited to the following arrangment.Indication of Zone sprinklerIndication of zone faultFire/fault hooterAlarm cancel for fire/faultBattery for emergency back up of 4 Hrs.

Providing and Fixing 15 mm dia gunmetal / brass quartzoid type Sprinkler Head with quartz bulb and set to operate at specified temperature.Pendent / Upright type, 68 C, Chrome plated

Side wall extended throw 20 mm dia 68 C, Chrome plated

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 10 mm thick dished ends and 8 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal wheel valve complete with all accessories etc. as required of the following sizes 1.2 Metre high and 250 mm dia

Supply, Installation, Testing and Commissioning External Yard Hydrant Stand Post comprising of GI pipe 80 mm dia (heavy duty C class) from existing ringmain to about 1 meter above ground level and Single Headed Yard Hydrant Valve with 80 mm dia flanged inlet, intantanneous gunmetal coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS : 5290 (Type A), with ABS cap and chain etc.complete with all accessroies as required.

Providing and placing on terrace polyethylene water storage tank ISI : 12701 MARKED indicating the BIS license No with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supply, erection, testing & commissioning of exit glow sign board of size 200mm x 350 mm wall mounting signage consisting of photo luminescent coating on acrylic cover

Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed. 4.5kg capacity cylinder

Providing and fixing 9 liters capacity fire extinguisher water type gas pressure conforming to IS marking, fixed to wall.

Providing and fixing ABC type fire extinguishers complete in all respects. Capacity 5.0 Kg.

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header in pump house fabricated out of 10 mm thick dished ends and 8 mm thick MS sheet, Air Release Valve, complete with drain arrangement with 25 mm dia gun metal wheel valve complete with all accessories etc. as required of the following sizes 2 Metre high and 450 mm dia suitable to operate Jockey Pump, Main Fire Pump & Diesel Engine Driven Fire Pump

Providing and fixing C.I. non-return valve complete with gunmetal seat, bolts, nuts washer & rubber insertions as required conforming to IS:5312.150 mm dia

80 mm dia

Supplying, installing, testing and commissioning of electric driven fire pump suitable for automatic operation consisting of the following (as per CPWD specification Part V-1985 for Fire Fighting and its amendments) (For Hydrant system & Sprinkler system).Fire pump with stainless steel impeller, CI casing, SS shaft & mechanical seal shall be horizontal split casing centrifugal suction type multistage having following capacity and head so as to ensure a minimum pressure of 3.0 kg per square cm. at the highest and farthest out let at the specified flow complete with necessary strainer / foot valve suction side and pressure gauge on the delivery side including by pass arrangement for periodical testing of the working of the pumping set as required. The pump shall be provided with mechanical seals.Squirrel cage type TEFC motor suitable for operation on 415V, 10%, 3 phases 50 Hz. system of suitable HP for the above pump with synchronous speed of 1500 RPM and flexible coupling. The pump motor should conform to IS: 325-1978.Common bed plate fabricated from mild steel channel or cast iron type.Suitable cement concrete pump foundation & vibration damping arrangement with cushy foot mounting as required. Capacity 2280 LPM and Head 65 Metres

Supplying, installing, testing and commissioning of diesel engine driven fire pump suitable for automatic operation consisting of the following (as per CPWD specifications PartV 1985.) (For Hydrant system & Sprinkler system).Horizontal centrifugal type multi-stage, fire pump with stainless steel impeller CI casing, SS shaft & mechanical seal complete of following capacity and Head so as to ensure a minimum pressure of 3.0 kg per sq.cm. at the highest & farthest outlet at the specified flow, complete with necessary strainer pressure gauge on the delivery side etc. including by pass arrangement for periodical testing of the working of the pump set as required. The pump shall be provided with mechanical seals.Water cooled cold starting type multi cylinder 4 stroke diesel engine, developing suitable BHP at 1500 RPM for the above pump set with automatic starting mechanism, cooling system shall be with radial cool engine, maintenance free batteries, battery charge unit, flexible coupling with the pump, common bed plate for mounting diesel engine fuel day tank fuel piping and pump and vibration damping arrangement by cushy foot mounting as required complete in all respects. The engine shall be capable to drive the pump at 150% rated discharge at 65% head and shall be suitable for 10% overload capacity for one hour in any period of 12 hrs. continuous run.Common bed plate fabricated from mild steel channel or cast iron type.Isolation ValveSuitable cement concrete pump foundation & vibration damping arrangement with cushy foot mounting as required. Capacity 2280 LPM and Head 65 Metres

Supplying, installation, testing and periodic commissioning of electric motor driven automatic pressurization pump set consisting of the following (as per specification) (For Hydrant system & Sprinkler system). Centrifugal pump of 180 LPM capacity capable of building up pressure lost in any leakage in the system against atotal head (mentioned as under) complete with C.I. casing stainless steel impellor ; mechanical seal & S.S. shaft necessary strainer, pressure gauge on delivery side etc. including by-pass arrangement for testing of the working of the pumping set as required . Squirrel cage A.C. induction motor suitable for operation on 415 V, 10% 3 phase 50 Hz. A.C. supply and of minimum 7.5 HP,1500 RPM, for the above pump with flexible coupling as per specification and conforming to IS: 325/ 1978 and shall be TEFC type only.Common bed plate fabricated from mild steel channel or cast iron type.Suitable cement concrete pump foundation with vibration damping arrangement with cushy foot or similar mounting as per required.Head - 65 Metres

Providing & fixing puddle flanged including 40 cm long GI pipe piece welded / threaded with MS plates 450x450x6mm thick with both end screwed / flangedFor 80 mm dia pipe

for 150 mm dia pipe

for 200 mm dia pipe

Supplying, fixing, installation, testing and commissioning, control valves comprising of :150 mm dia1 No. alarm motor & gong (hydraulically operated.1 No. main stop valve1 No. alarm valve.Pressure gauges drain pipe.

Providing & fixing electrical gang bell with all inter-connecting cables for an audio annuciation of pumps failure, complete in all respects.

Providing & fixing half mile range siren with all inter connecting cables and wires complete in all respects.

Suitable cement concrete pump foundation with vibration damping arrangememnt with cushy foot mounting as required and having provision of suitable weather protection cover.

Supply, installation, testing and commissioning of following M.V. cubicle type totally enclosed, free standing type, wall mounted type, dust, damp and vermin proof, indoor type Distribution Board/Panel complete with busbars, M.V. danger notice plate, interconnections with suitable capacity aluminium leads/solid aluminium strips/rods, connection of incoming and outgoing cables with thimbles, powder coat painted and having following incoming and outgoing switchgears complete as required.

Passenger Lift

Supplying and installation of Passenger Lift 13 person capacity, weight-544 Kg., Speed 1.5 M/Sec, G+4, Power operated, ACV VVF

Sewage Treatment Plant

Planning,Designing,Detailing,Supplying, Erection,Testing and Commissioning of Package Sewage treatment plant based on MBBR (Moving bed Bio Reactor)/FAB technology of average flow rate of 185 cu.m/day for sewer including provision of recirculation of treated sewage/effluent for the use of horticulture purposes including design and execution of all civil,structural,electrical,mechanical, plumbing and processing,ancillary equipments and works etc required to complete the package, getting approval from state pollution control board and other statutory bodies as well as from consultant (HSCC) including the cost of STP building for electrical room, treated sewage under ground storage tank of 80 cu.m capacity etc. All the water retaining structure shall be designed as water retaining structure as per provision of IS code and water proofing with fixed or any other approved chemical shall be carried out by approved agency with 10 year (minimum) garanty. All the unit shall be painted by epoxy or any other approved paints.''RCC Suitable size Bar Screen chamber with minimum free board 300 mm and minimum size 0.5mx1mx0.3m SWD and suitable size SS Bar screen with minimum size of bar 5x25 mm is installed at suitable angle at the inlet of raw sewage sump before pumping and manual system to collect and transport the screening material . The unit shall be designed for peak flow - 1 no.(min.).Electrical & mechanical(1 Nos)

Supply, installing, testing and commissioning vertical fully floodable type submersible drainage pump of non-corrosive material with shredder/cutter in close coupled design single stage, suitable for handling minimum 20 mm dia solids for transferring raw sewer from sump to outside the building with float switch for automatic start and stop arrangement with panel and wiring, chain and pulley, mechanical seal complete in all respect as per instruction of the Engineer in charge. (The shop drawing or the pumps along with its characteristics curves, model and technical data etc. are to be submitted for approval before purchase of pump).Star delta suitable starter complete in all respect for automatic/manual operation of pump,start and stop push button contactor with required overload production and single phase preventor. 'Material of Construction (M.O.C): Corrosion Resistant in gen n: Casing — Cast Iro Impeller — Ductile cast iron/SS: Bearings — Anti friction, prelubricated ball bearings, packed with grease for life.' Motor: — Dry Motor with built in over load protectionProtection - IP68.Insulation Class - FRAW SEWAGE PUMP-(2 nos min.)Capacity - 65LPM (min.)''Head - 8 mSolid handing - 5-10mm

RCC Equalisation tank with hydraulic retention time Min.6 Hrs HRT of suitable Size free Board 500 mm,the effluent of equalisation tank is agitated with diffused air that is fed by an air blower, including pipe non-corrosive material and its complete system. (1 unit) 'Civil-will be paid seperately in civil work''Mechanical & ElectricalRCC MBBR-(2 nos. minimum) with minimum 2.5hr. retention time of each reactor of suitable size with Air grid CPVC pipe material of construction or corrosion resistant material,Air diffusers (fine bubble), HDPE approved make Bio media for each aeration tank,with minimum water depth of 2 m.'Electrical / mechanicaL

Civil(2 Nos)-will be paid seperately in civil work'ROTARY AIR BLOWERS'Providing and Installation of Rotary air blowers for air scouring, driver through v-belt or directly coupled through flaxble coupling. Motor shall be of suitable HP for 200-240 volts, ,1000RPM, 3 phase, alongwith air filter, non-return valve, safetyvalve, base plate and necessary air piping fittings, valves, flowmeters etc.'(Blower capacity and pressure head shall be suitable to meet the requirement of equalisation tank and Bio reactor suitable for average flow rate of sewer of 185cu.m per day)- 2 nos.(1working +1 stand by)

a) 'RCC secondary tube settler -1 no. maximum Hydraulic loading 2.0 cu.m/sq.m/hr and with approved quality media. (1 units)'Electrical & mechanical(1 No.)

ix) 'Providing and fixing of OxiLyte (Mixed Oxidant) Generation System, based on ECA Technology, producing non toxic mixed Oxidant Slution at 1000 ppm of Oxidant Concentration or any other approved disinfection method excepted by HSCC. The solution should be at a pH 3+-0.5 suitable for 24x7 operations should produce 50litre per hour. The system should be supplied complete with appropriate dosing pumps , valves, piping, fittings, chemical dosing tank etc. complete in all respect.(2 unit)'RCC supernatant tank/Filter feed tank minimum 7.5 cu.m capacity (1 unit) with filter feed pumps - The civil work will be paid seperately

Providing and installation horizontal single/multistage centrifugal monoblock pumping set with CI body, SS impeller, coupled with totally enclosed fan cooled inlduction motor mounted on common structural base plate with all pump accessories complete as per specifications inclusive rubber vibration eleminators motor suitable for 415 volts, 1000RPM, 3 phase 30 HZ. A/c supply.Type of pump - Horizontal' 'Capacity -75 LPM, Head - 15 M, 'Nos.- 2 (min.)

'Providing and installation of mild steel pressure vessel ( as per IS:2825) 6 mm thick natural rubber lining fabrication standard multi grade filter complete in all respects, of total capacity 150LPM, complete with dished ends, supporting legs, manhole cover, frontal pipe work fitting with valves. Plant shall be provided with inlet, outlet pressure gauge, sample cocks, charge of filter media graded sand and internals consisting of strainers fitted on plate for collection. (No. of unit-1) Dia of vessel-350mm (minimum)

Providing and installation of mild steel pressure vessel ( as per IS:2825) 6 mm thick natural rubber lining fabrication standard multi grade filter complete in all respects, of total capacity 150LPM, complete with dished ends, supporting legs, manhole cover, frontal pipe work fitting with valves. Plant shall be provided with inlet, outlet pressure gauge, sample cocks, charge of approved quality activated carbon media. (No. of unit-1)

XII) 'RCC sludge sump (5cu.m minimum) and submersible sludge pump set with CI body, SS impeller and shaft coupled with to a totally enclosed fan cooled iniduction motor complete with HDPED/F pipings, sluice valves, non return valves, fittings etc as required. Motor suitable for 415 volts, 3 phase 50Hz. A/c supply with control auto start float switch with return sludge line upto Bioreactor. 'SLUDGE PUMP- (2 nos. minimum)'Capacity -35 LPM

XIII) 'Providing and fixing 15plates 400 x 400mm size filter press - 1no. with suitable sludge pump(screw type) and sludge tank of 1,000 ltrs. (min.) capacity alongwith piping, fittings valve etc. complete in all respects.

M/S G B ENTERPRISE