SPECIAL REPAIRS TO BLDG NO P 09 AT MALAD COMPLEX, MUMBAI

Amount

Demolition of cement concrete of old water proofing treatment of any description and in any position, not otherwise specifically provided for, any thickness above ground floor including removing debis out side MD land complete all as specified and directed by Engr-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., applying neat cement slurry @ 3kg of cement per square metre complete all as specified and as directed by Engr-in-Charge.

M & L for 50mm thick (average) Plain cement concrete 1:2:4 typ B-1, Nominal mix (using 20mm graded stone aggregate) on roof slab/terrace as levelling concrete, laid to slope and finished even and fair without using extra cement complete all as specified and as directed by Engr-in-Charge.

M & L for rendering 10 mm thick cement plaster in cement mortar (1:3) on roof slab/ canopies/chajjas with water proofing compound @ 3% by weight of cement or as per manufacturer's instructions and make surfaces to receive water proofing treatment, finished even and smooth without using extra cement complete all as specified and directed. Note: water proofing compound will be measured and paid separately as "Supply only"

M & L for preparation of terrace and applying Prime the surface with ShaliPrime WB , diluted with water in the ratio 1 : 0.5 and apply @ 5-8 L / m2 and apply the coat of Shalicry LM without any dilution and allow it to dry before taking up the second and third coats, the rate of application being the same. The Colour of First and Last Coat will remain same. Drying time between coats will be 6 to 8 hrs. Allow the system to air cure for 7 days minimum. A total thickness of 1 to 1.2 mm must be achieved when Shalicryl LM is Dry. Apply Top coat of ShaliUrethane BTD white/ShaliUrethane LM HI complete all as specified and as directed by Engr-in-Charge. Note : (i) DEscription of item is as per M/s STP Ltd. However Work can also be carried out by FOSROC/ Dr FIXIT as their instructions for the above mentioned item of work to achieve the desired result. (ii) Work Shall be Executed through manufacturer applicator only. .

M & L for applying two coats of flexible polymer acrylic water proofing coating, 1mm thick (Dry film in two coats), using Dr Fixit pidifin 2K of M/S Pidilite Industries or equivalent as approved by GE including necessary pond testing in sunken portion complete all as specified and directed by Engineer-in-Charge.

S & F 32mm GI pipe, medium grade as in spout, n.exc 1.00 Rm each (in short length) complete all as specified and as directed by Engineer-in-Charge. Make: Tata/Jindal/Zenith/Swastik/Prakash

M & L for Plain cement concrete 1:5:10, type E2 using 40mm graded stone aggregate as in sunken floor complete all as specified and as directed by Engr-in-Charge.

Demolition of brick work, built in cement mortar or cement lime mortar including all quoins and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

M & L for brick work with sub class "B" bricks, straight or curved on plan, exc 6 mtr mean radius with old size bricks and built in cement mortar (1:6) complete all as specified and as directed by Engr-in-Charge

M & L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius, in half brick thick walls with old size bricks, built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge

M & L for Surface preparation of existing concrete components including grinding/rubbing carefully by grinder without damaging the existing concrete, cleaning the surfaces by blower , removal of damaged external plaster wherever exists, cleaning thoroughly with water including removing debis out side MD land complete all as specified and directed by Engr-in-Charge.

S & F CRS (Corrosion resistant steel) , 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. (Note: Rate includes cutting of rusted reinforcement & welding with existing reinforcement)

S & F CRS (Corrosion resistant steel), 8 to 10mm dia in stirrups, spacers and binders , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. (Note: Rate includes cutting of rusted reinforcement & welding with existing reinforcement)

Demolition of reinforced cement concrete of any description, in any position, not other wise specified including removal of debris out side MD land complete all as specified and as directed by Engr-in-charge. (Note:-Reinforcement cut as required to facilitate demolition).

S & F MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour and but excludes the materials for grouting the pins.etc complete all as specified and as directed by Engineer-in-Charge.

Providing and casting and repairing of excessively damaged members with microconcrete at all levels with all leads and lift as directed including mixing , laying, levelling, finishing including curing complete all as specified and directed by Engr-in-Charge. Note: Grade of Micro-concrete to be M 30 at 28 days and shall be sourced from manufacturer's such as Fosroc / SIKA / BASF / Krishna Conchem as approved by GE.

M & L for formwork using steel shutters or 12mm marine ply to have the smooth finish to pour the microconcrete/ concrete including de-shuttering etc complete all as specified and as directed by Engr-in-Charge.

M & L for providing and applying rust cleaner of approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc. complete as directed by Engineer-In-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika

M & L for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB of M/s Krishna Conchem or equivalent of approved make and quality comprises of resin and hardener mixed in equal proportion by volume with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE NOTE:- New Reinforcement shall be measured and paid separately under respective item. (b) Cost of welding deemed to be included in this item of work.

M & L for providing and applying a priming cum bonding coat of two component Epoxide Resin conforms to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method for joining old and new concrete as per technical specifications of manufacturer etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE Note- Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-charge

M & L for Drilling and fixing Teflon nozzles in RCC members, including drilling holes (drilling 12 mm dia, 40mm deep holes in structural members at the intervals of 600mm c/c in staggered manner or as directed by Engineer-in Charge in RCC structure elements and cleaning the holes (to clean the holes by air blower prior to fixing nozzles) and fixing of nozzles (to insert 12mm dia teflon nozzles in cleaned holes external end of nozzles (to insert 12mm dia Teflon nozzles in cleaned holes external end of nozzles to be machined to receive outlet of grouting gun and fixing it inside the holes by applying thixotropic epoxy putty to ensure complete sealing and curing the system for minimum 12 hrs) and cutting of nozzles (to cut the nozzle by chisel after completion of grouting without damaging structural elements etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE

M & L for Injecting low viscosity (3-5 cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories, till nozzles refuses to accept the grout, Including mixing of materials( Mixing material components (part a & b) in required quantities as per manufacturer’s instruction by weigh batching) and Grouting ( Filling the grouting gun with monomer, maintain desired pressure in the gun by air compressor; maintain the pressure at exit (4 to 5 Kg/ Sqcm) by monitoring pressure gauge at exit, grouting the material through prefixed nozzles in the structural elements till its refusal, sealing the nozzle with epoxy putty after the refusal, monitoring leakages through other nozzles while grouting and seal them as per the requirement, repeat the process for all the nozzles. the operation to be within pot life of the material.) and Cleaning of gun and accessories (The gun and accessories like valves, pipes and other fixtures to be cleaned with thinner after the operation to avoid jamming of the gun.) etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE

M & L for providing and laying 20 mm thick POLYMER MODIFIED MORTER over identified R.C.C. members in One layer in the proportion of as per approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE

M & L for Strengthening structural elements with non metallic composite fiber wrapping system comprise of uni-directional carbon fiber sheet (430 GSM) and compatible saturant Profiling, applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixotropic epoxy putty etc. , complete mechanized wetting of fiber sheet, cutting the fabric to required size, mixing of saturant and filling in tub area of the saturation machine, placing the fiber on metallic rods and pass through the rollers of machine and saturant tub ensuring complete wetting (65% fiber volume fraction) of fibers, removing the fiber on rod and placing the new fiber sheet, wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc., repeating the same procedure for multiple layer with the interval of 8 hrs ,applying second coat of saturant after minimum 12 hrs after first coat, rectify air voids if any and finally rendering with10mm thick in CM 1:6 including finishing even & smooth without using extra cement complete all as specified and as directed by Engr-in-Charge. Mode of measurement- Per sq.mt of surface area of carbon fiber sheet without lapping. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE

Providing and fixing carbon fiber anchor including drilling hole in the base concrete, fixing the anchor using epoxy 50X55 system, spreading the anchor fibers in star pattern including application of saturant etc complete as specified by manufacturer and as directed by Engineer-In-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engr-in-Charge

M & L for rendering 10mm thick on internal wall surfaces using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Soundp last PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:6 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over masonry and concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge.

M & L for rendering 5 mm thick on ceiling using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Soundplast PMC-1 of M/s Sound build care Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering in ceiling, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge

M & L for rendering 15 mm thick cement plaster in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix' of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S :1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 10 mm thick and finishing coat of 5 mm thick final rendering with water proofing compound @ 3% by weight of cement or as per manufacturer's instructions, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing including provide of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry at external faces before plastering including scaffolding at any height and all safety materials required for execute work etc complete all as specified and as directed by Engr-in-Charge.

Supply only water proofing compound, ISI marked complete all as specified and as directed by Engineer-in-Charge.

M & L for opening out cracks in wall surfaces in 'V' shape by mechanical grinder and removing the loose material. filling with crack filler of Dr. Fixit crack-X, shrink-free or equivalent all as per manufacturer's instructions and finishing the surfaces to match with existing finish complete all as specified and as directed by Engr-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as appproved by GE

M & L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over a thin layer of wall care putty complete all as specified and directed by Engineer in Charge. Make: SHALIMAR / BERGER / NEROLAC / ICI LTD/ASIAN (Tractor Brand)

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engr-in-Charge.

M & L for preparing of new plastered surfaces of wall and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over a coat of acrylic primer over thin layer of water proof wall care putty complete all as specified and directed and as per manufacturers instructions. Make- (a) Asian Paint - Apex exterior emulsion 100% acrylic. (b) Berger Paint - Weather coat smooth. (c) Nitco Paint - Outshine premium 100% acrylic exterior (d) ICI Dulux - Weather shield exterior.

Taking down chowkats or frame with shutters n exc 1.5 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engr-in-Charge

Taking down chowkats or frame with shutters exc 1.5 sqm n exc 4.00 sqm each (without taking off shutters from the frames) including all fittings B80

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each including fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engr-in-Charge

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 160 of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet complete all as specified and as directed by Engr-in-Charge. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S Accucell/M/S Dura Plast Extrusion

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 156 of SSR Part II (pertaining to item No 08080) complete all as specified and as directed by Engr-in-Charge. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S Accucell/M/S Dura Plast Extrusion

S & F plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good frame in cement concrete complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing surfaces of wood and wood based materials, steel and iron work, treating ends of posts, hold fasts, backs of chowkats, etc., area tarred not exceeding 0.5 sqm each and treated with tar or coal tar black paint complete all as specified and as directed by Engr-in-Charge.

S & F mild steel work as in hold fast & similar small articles, conforming to Fe-290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

M & L for Plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in bed plates, concrete block for hold fast etc including necessary form work complete all as specified and as directed by Engineer-in-Charge.

S & F factory made plain framed panelled shutter 35mm thick 2nd class hardwood rail and style (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

S & F 35mm thick factory made 2nd class hard wood glazed and skelton shutter, open rebated, prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clasue No 8.24 (b) complete all as specified and as directed by Engr-in-Charge.

S & F extruded aluminium alloy handles, fabricated type, anodised, of size 150 mm complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F stainless steel butt hinges, heavy duty of 100mm size complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F aluminium anodised barrel tower bolt of extruded section of size 150mm complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F aluminium anodised barrel tower bolt of extruded section of size 200mm complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy , 250mm long, ISI marked complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy , 300mm long, ISI marked complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

M & L for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make-(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

M & L for preparing old wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. Make-(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

S & F 15 micron coloured aluminium sections for sliding or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engr-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note:- (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

S & F 4mm thick black tinted glass, ordinary quality, in square exc. 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engr-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

S & F Stainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture, 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engr-in-charge.

S & F in repairs 15 micron coloured aluminium anodised grill of design No DG-101, cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engr-in-Charge. Make- DECOGRILLE of Associated group or equivalent make as approved by GE

Taking down aluminium window shutter carefully from aluminium sliding frame, n exc 1 sqm each and refixing in same position after replacing the window glass pane, wiremesh and nylon roller, rubber beading etc complete all as specified and as directed by Engineer-in-Charge. Note: Glass pane and wiremesh will be measured and paid separetely under respective item.

Taking down aluminium window shutter carefully from aluminium sliding frame, exc 1 sqm but n exc 2 sqm each and refixing in same position after replacing the window glass pane, wiremesh and nylon roller, rubber beading etc complete all as specified and as directed by Engineer-in-Charge. Note: Glass pane and wiremesh will be measured and paid separetely under respective item.

S & F 5.5mm thick black tinted glass, ordinary quality, in square exc. 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engr-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Taking down chowkats or frame with shutters n exc 1.5 sqm each (without taking off shutters from the frames) including all fittings & refixing in same opening complete all as specified and as directed by Engr-in-Charge

Taking down chowkats or frame with shutters exc 1.5 sqm n exc 4.00 sqm each (without taking off shutters from the frames) including all fittings & rrefixing in same opening complete all as specified and as directed by Engr-in-Charge

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete in ground floors and pavings, n.exc. 15cm thickness (below or above ground level) including floor finish and removal of debris outside MD land complete all as specified and as directed by Engr-in-Charge

M & L for 75mm thick cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in sub base of flooring/ hard standing/ path and finishing the surfaces even and fair without using extra cement complete all as specified and as directed by Engr-in-Charge.

M & L for 75mm thick cement concrete (1:3:6) type C1, using 20mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cement, including joints of plinth protection filled with bitumen mastic (1:3) complete all as specified and as directed by Engr-in-Charge.

M & L for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in colour cement to match including backing coat 10 mm in CM (1:4) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for glazed coloured ceramic tiles, 1st quality of size 350 x 250 x 7 mm thick or 450 x 350 x 7mm thick (or nearest size) on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in colour cement to match including backing coat 10 mm in CM (1:4) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for machine cut Kota (greenish colour, pre polished) stone slab flooring, 18-20 mm thick, in one piece as in cill/staircase treads, over cement screed bed 20 mm in CM (1:3) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer in Charge.

M & L for machine cut Kota (greenish colour, pre polished) stone slab flooring, 18-20 mm thick, in one piece as in staircase risers, set and jointed in neat cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and pointed in colour cement to match including backing coat 10 mm in CM (1:3) complete all as specified and as directed by Engr-in-Charge.

M & L for machine cut Kota (greenish colour, pre polished) stone slab flooring, 18-20 mm thick, in one piece as in skirting, set and jointed in neat cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and pointed in colour cement to match including backing coat 10 mm in CM (1:3) complete all as specified and as directed by Engr-in-Charge.

M & L for Rounding the edges of stone slab as in steps, cooking platform and similar situations complete all as specified and as directed by Engineer-in-Charge.

Extra over for providing two grooves over staircase treads complete all as specified and as directed by Engineer-in-Charge. Note- Two nos grooves shall be measured as one length for payment.)

Demolition of stone slab and tiles of any description or thickness in floor, apron and vertical surfaces, laid dry or laid dry and pointed and removing debris outside MD land complete all as specified and as directed by Engr-in-Charge.

M & L in repairs for machine pressed precast concrete interlocking paver block laquer finish of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment including 25mm thick crushed stone sand cushioning including watering and consolidation below paver block cushioning complete all as directed by Engr-in-charge.. Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur

S & F 32mm outer dia, three layer PP-R polypropylene random copolymer concealed pipes SDR- 7.4 (PN-16) UV stabilized and antimicrobia+B83l fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or in floors including taking down of old steel tubing complete all as specified and directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/SHK Polymers

S & F 25mm outer dia, three layer PP-R polypropylene random copolymer concealed pipes SDR- 7.4 (PN-16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or in floors including taking down of old steel tubing complete all as specified and directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/SHK Polymers+B89

S & F 20mm outer dia, three layer PP-R polypropylene random copolymer concealed pipes SDR- 7.4 (PN-16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or in floors including taking down of old steel tubing complete all as specified and directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/SHK Polymers

S & F in repairs PVC (SWR), type B, single socketed, rain water/soil waste/vent pipes with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR), type B, single socketed, rain water/soil waste/vent pipes with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) bends any radius, 110 mm bore with access door complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) bends any radius, 75 mm bore with access door complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) branch piece, single ( single Y), equal or unequal, 110 mm bore at any storey of bldg complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) branch piece, double (double Y), equal or unequal, 110 mm bore at any storey of bldg complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) junction single, (Single T), equal or unequal for 110mm dia bore complete all as specified and directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) branch piece, single ( single Y), equal or unequal, 75 mm bore at any storey of bldg complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) branch piece, double (double Y), equal or unequal, 75 mm bore at any storey of bldg complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) vent cowl, 110 mm bore complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC (SWR) vent cowl, 75 mm bore complete all as specified and as directed by Engr-in-Charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repair 32mm bore low density polyethylene pipes(LDPE) of pressure rating 6 kg/ cm2 laid in trenches or in floors or fixed to wall complete all as specified and as directed by Engr-in-Charge.

S & F in repair 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by Engr-in-Charge. Make: Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs, bib taps, fancy type, chromium plated, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed. Make- (i) Jaquar (ii) Marc (iii) CERA (iv) Kohler

S & F in repairs concealed type stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engr-in-Charge. Make- (i) Jaquar (ii) Marc (iii) CERA (iv) Kohler

Supply only in repairs pillar taps fancy type cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engr-in-Charge. Make- (i) Jaquar (ii) Marc (iii) CERA (iv) Kohler

S & F in repair Jet spray (Butterfly) with 1Mtr tube Cat No-BEA-17 of Make-Prayag or equivalent as approved by GE) complete all as specified and directed by Engr-in-Charge.

S & F in repair health faucet (body cleaner) with 1.0m tube and hook (PVC tube), white/Ivory Cat No- BEA-84, Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engr-in-Charge.

S & F in repair, CP brass soap Dish Cat No- BA-15 (Make-Prayag or equivalent as approved by GE) complete all as specified and directed by Engr-in-Charge.

S & F in repairs tubular towel rail chromium plated 20mm dia, 'D' type, 60cms long between flanges fixed to walls with screws complete all as specified and as directed by Engr-in-Charge.

S & F in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm), including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc complete all as specified and directed by Engineer-in-Charge. Make:Neycer Kermag (Standard)/Hindustan Sanitary Ware Industries (Ist Quality)/Parryware (Super Fine)/Cera(Ist Quality)/Jaquar

S & F in repairs vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rest (excluding flushing Cistern, flush pipe etc) including 'P' or S trap, connector piece of CI pipe upto 'T'/ 'Y' joint and connection to trap and to flushing pipe, anti-syphonage pipe etc and provision of lime concrete bedding complete all as specified and as directed by Engr-in-Charge. Make:Neycer Kermag (Standard)/Hindustan Sanitary Ware Industries (Ist Quality)/Parryware (Super Fine)/Cera(Ist Quality)/Jaquar

S & F in repairs PVC valveless, syphonic action type low level dual flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets and connection to pipes and fixing of chain and pull or lever complete all as specified and as directed by Engr-in-Charge. Make:Commander/Slimline/Hindustan Sanitary Ware Industries

S & F in repairs flush pipe of polyethylene of low or high density or PVC, 32mm dia complete all as specified and as directed by Engr-in-Charge.

S & F in repairs cast iron Nahani trap, 75mm dia outlet with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc, complete all as specified and as directed by Engineer-in-Charge. Make- (i) Electro-Steel (ii) Kejriwa (iii) NECO (iv) Kesoram

S & F in repairs PTMT grating rounded of dia 100mm (minimum weight 25gms) complete all as specified and as directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F in repairs PVC connection 15mm dia with of length 450mm with both end socket complete all as specified and as directed by Engr-in-Charge.

S & F in repairs vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm excluding taps, waste chain and plug and porcelain stopper including brackets,chromium plated waste coupling, waste fitting etc, cutting for and pinning in ends of brackets, connecting to supply and waste pipe complete as specified and directed. Note:- Pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately) Make:Neycer Kermag (Standard)/Hindustan Sanitary Ware Industries (Ist Quality)/Parryware (Super Fine)/Cera(Ist Quality)/Jaquar

S & F in repair vitreous china bowl urinal, flat back, size 465 x 355x 265 mm white (minimum), with grating and urinal for discharge pipe, waste pipe complete including providing and fixing plugs, bedding urinal against wall in CM securing urinal to plugs with and incl 60mm long brass screws, pointing around, fixing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and as directed by Engr-in-Charge. Make:Neycer Kermag (Standard)/Hindustan Sanitary WareIndustries (Ist Quality)/Parryware (Super Fine)/Cera(Ist Quality)/Jaquar

Supply only 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engr-in-Charge.

Supply only PVC waste pipe 32mm bore of size 450mm to 600mm long complete all as specified and as directed by Engr-in-Charge.

Demolition of reinforced cement concrete (other than ground floor) as in roofs, floors, staircase, chajjas, landing and other suspended work complete all as specified and as directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engr-in-Charge.

S & F rolled mild steel sections as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and conforming to Fe - 410 W (Grade E-250) 'A' quality including riveting / or welding and fixing with screws, bolts etc. complete all as specified and as directed by Engr-in-Charge.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated, steel sheet 0.50mm thick (total thickness including coating) of any colour having tensile strength of 550 MPA as in cladding to wall, roof covering, fixed with self tapping screws including dismantling existing asbestos sheet complete all as specified and as directed by Engr-in-Charge. Make- (i) TATA (ii) JSW (iii) ESSAR (iv) HINDALCO (v) INDALCO (vi) ASSOCIATED PROFILES AND ALUMINIUM LT

M & L for Mild Steel framed work such as grills, gratings, etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, framed work of garbage bin, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to FE 290 Gde 165 etc. complete all as specified and as directed by Engr-in-Charge.

M & L for preparing new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-Charge. Make-(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

M & L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge. Make-(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

S & F PVC Rotational moulded polyethylene water storage tank ISI marked Double layered (Cylindrical Vertical with closed top) of 1000 litre capacity including tank nipple, bends, sockets, couplet all fitting required at site incl taking down old PVC storage tank complete all as specified and all as directed by Engr-in-Charge. Make- (i) M/s Sintex (ii) M/s Infra (iii) M/s Ashish Plast (iv) M/s Yash Engineering Works, Pune 09422007879 (v) M/s Plasto (vi) Polycon

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation etc or for shaft, walls, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense soil complete all as specified & directed by Engineer-in-Charge

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any soil all as specified & directed by Engineer-in-Charge.

Removing excavated material to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge

S & F in repairs steel water tubing of size 25mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, laid in trenches and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in-Charge. Make- (a) Tata (b) Swastik (c) Jindal (d) Surya (e) Prakash (f) Indian Tube Company (g) Zenith (h) BST (j) GST (Gujrat Steel Tube)

S & F in repairs steel water tubing of size 40mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, laid in trenches and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in-Charge. Make- (a) Tata (b) Swastik (c) Jindal (d) Surya (e) Prakash (f) Indian Tube Company (g) Zenith (h) BST (j) GST (Gujrat Steel Tube)

S & F in repairs steel water tubing of size 50mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, laid in trenches and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in-Charge. Make- (a) Tata (b) Swastik (c) Jindal (d) Surya (e) Prakash (f) Indian Tube Company (g) Zenith (h) BST (j) GST (Gujrat Steel Tube)

S & F in repairs 25mm bore Gun Metal Gate Valve with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engr -in-Charge. Make- (i) Leader (ii) Zoloto (iii) Sant (iv) Hansa (v) Seiko (vi) GEM (Vii) GMP

S & F in repairs 40mm bore Gun Metal Gate Valve with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engr -in-Charge. Make- (i) Leader (ii) Zoloto (iii) Sant (iv) Hansa (v) Seiko (vi) GEM (Vii) GMP

S & F in repairs 50mm bore Gun Metal Gate Valve with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engr -in-Charge. Make- (i) Leader (ii) Zoloto (iii) Sant (iv) Hansa (v) Seiko (vi) GEM (Vii) GMP

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, switch socket outlet, bulk head fittings, tube light fittings etc and removing unserviceable materials from site of work after credit for the same is recovered by the dept and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed by Engineer-in- Charge

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed, multistranded copper conductor cable conforming to IS-694 of size 1.5 sqmm 1100 volts grade drawn through and including PVC casing capping 20mm / 25mm on surface conforming to IS-9537 and accessories including 16 SWG mild steel sunken box for housing of switch, socket, regulator etc, concealed in wall, flush with wall, with 3 mm thick PVC laminated top cover complete with and including 1.5 sqmmFRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with existing surface complete for one Light/fan/bell point controlled by one switch complete all as specified and as directed by Engineer-in-Charge.

All as per Item No.132 here-in but for One 5 pin socket point 5 Amps on independent board

All as per Item No.132 here-in but for One 5 pin socket point 5 Amps on same board controlled by another switch

All as per Item No.132 here-in-before but for one socket point on independent board, 15 Amp with 2.5 sq mm PVC unseathed FRLSH wire along with 2.5 sq mm FRLSH green colour wire as earth continuity conductor connected to common earth dolly complete all as specified & as directed by engr-in-charge.

S & F ceiling rose, PVC/Polycarbonate, insulated body, three terminals complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F Switch, piano type, single pole, one way, 5 amps, 240 volt flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F switch socket outlet, 5 Pin, 6 Amps, flush type complete all as specified and as directed by Engineer-in-Charge. Make :(i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F switch socket outlet, 6/16 Amps, 6 in 1, flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F Switch, piano type, single pole, one way, 15/16 amps, 240 volt flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F ceiling fan regulator AC, 230 volts, electronic rotary step socket type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F in repairs LED tube light fitting 1 X 18 Watts, 230 volts, all pre wired fixed on walls or ceiling with all fixing accessories such as 2 Nos of PVC square/round box, screws etc and connecting up three core flexible copper conductor cable of size 24/0.20 sqmm including LED tube light complete all as specified and as directed by Engineer-in-Charge. Make:-LDESLM-18 of Crompton greaves or equivalent in Wipro/Bajaj/Havells

S & F in repairs LED Security light fittings and commissioning LED street light fittings 1x 20 watts, pressure die cast aluminium road way with high powered LED, electronic driver, pressure die cast housing with epoxy powder coated dark graphite grey colour finish, prismmatic poycarbonate cover with individual LED lenses, IP 65 including bracket fabricated out of GI tubing light grade 25mm bore, bend to shape with necessary copper wire connection of suitable size, complete all as specified and as directed by Engr-in-Charge. Make :Philips Cat BRP022 LED 20 CW MR S1 PSU GR or Equivalent in Havells/Bajaj/CG/Surya

S & F angle holder, PVC/Polycarbonate with back plate suitable for batten/angular fitting, complete all as specified and as directed by Engineer-in-Charge. Make : Anchor/Crabtree/Leader/Legrand/Havells

S & F LED bulb, 10 Watt , retrofit type complete all as specified and as directed by Engineer-in-Charge. Make : Philips/Havells/Bajaj/CG/Surya

Taking down ceiling/exhaust fan of any make/ type/ size/ sweep, at site from any height of the building , sealing cable end, dismantling blades and removing fan and blades & depositing the same in MES store yard of AGE E/M(N) Mumbai for checking complete all as specified and as directed by Engr-in-Charge.

M & L for preparing old surfaces of ceiling fan/exhaust fan of any capacity or sweep, by scrapping and removing dust etc and filling cavities with one coat of filler and applying DUCCO paint by spray machine and writing MES Nos in block letters in black paint as per existing complete all as specified and as directed by Engr-in-Charge.

Hanging only ceiling fan of any sweep and make and connecting up including provision of flexible wire 23/0.0076 size, three core, 1100 Volt, twisted, PVC insulated, copper conductor, multistranded from ceiling rose or connector to fan complete all as specified and as directed by Engr-in-Charge.

S & F in repairs double door, sheet metal enclosure powder coated MCB DB SPN 8 way with 200 Amps rated bus bar, 240 volt, horizontal type, IP 43 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs Distribution board VTPN 4 way Vertical type double door 415 Volts as per IP-43 with provision for DPX 125Amps MCCB as incomer and SP/TP MCB as outgoing and electrically connected up complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs MCCB 3 pole with adjustable thermal & magnetic settings, 415 volts, 125 Amps with breaking capacity 25 KA including all connections and testing complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs MCB SP, 5amps to 32 amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs MCB SPN, 32amps to 63 amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

M & L for MCB blanking plate complete all as specified and as directed by Engr-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

M & L for Submain wiring complete with and including 2 runs of 6 sq mm single core FRLS PVC insulated and unsheathed multistranded copper conductor cable single core 1100 Volts grade drawn through and including PVC Casing and capping of size 20/25mm including accessories and fixed on walls and 4 sqmm FRLS PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Make for cable :(i) Havells (ii) Finolex (iii) Nicco (iv) Plaza (v) Anchor (vi) Polycab (vii) RPG (viii) GLOSTER (ix) RR Kabel (x) KEI Make for Casing& Capping : (i) Precision (ii) Modi (iii) Presto Plast (iv) Supreme (v) Polycab (v) Plaza (vi) Pressfit Note : Two runs of 6 sqmm PVC insulated cable and one run of 4 sqmm cable and one run of PVC Casing and capping shall be measured as one unit length.

M & L for Submain wiring complete with and including 2 runs of 4 sq mm single core FRLS PVC insulated and unsheathed multistranded copper conductor cable single core 1100 Volts grade drawn through and including PVC Casing and capping of size 20/25mm including accessories and fixed on walls and 2.5 sqmm FRLS PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Make for cable :(i) Havells (ii) Finolex (iii) Nicco (iv) Plaza (v) Anchor (vi) Polycab (vii) RPG (viii) GLOSTER (ix) RR Kabel (x) KEI Make for Casing& Capping : (i) Precision (ii) Modi (iii) Presto Plast (iv) Supreme (v) Polycab (v) Plaza (vi) Pressfit Note : Two runs of 6 sqmm PVC insulated cable and one run of 4 sqmm cable and one run of PVC Casing and capping shall be measured as one unit length.

M & L for earthing complete with galvanised steel plate earth electrode 600 mm X 600 mm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to earthing lead of 4.0 mm dia galvanised mild steel wire by means of bolts, nuts, check nuts and washers of galvanised iron from earth plate to test point upto 7.5 metre including all as shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete chamber in cement concrete M15 (Nominal Mix) using 20 mm nominal size coarse aggregate, precast RCC cover slab in cement concrete M15 (Nominal mix) using 20 mm nominal size coarse aggregate of size 40 cm X 40 cm X 5 cm reinforced with 8 mm dia TMT bars @ 150 mm c/c with one handle for lifting made out of 8 mm dia bar, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 20 mm dia GI pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/ strata and testing complete all as specified and as directed by the Engineer-in-charge.

kajal construction

Karma Construction Co