SPECIAL REPAIRS TO BLDG NOS. P/125, P/132, A/8/105 AND A/4/39 AT PMS UNDER GE PANAGARH

Amount

B/R PORTION

Dismantling of floor hearth or wall tilling including cement mortar bedding, removing rubbish off the premises for minor repairs to floor in patches, complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) not exceeding 15 cm thickness of any description and in any position not otherwise specifically provided , complete all as specified and as directed.

Demolition of reinforced cement concrete any thickness, complete all as specified and as directed.

Dismantling of cast iron pipes with all fittings and fixing acessories, jointed in cement mortar 50-100 mm bore, at any location, complete all as specified and as directed.

Demolition & breaking of AC rain water pipe 100mm dia, set in cement mortar & removing from site completed all as specified & as directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) in plinth protection, fineshed even and smooth without using extra cement complete all as specified and as directed.

M&L for providing cement concrete type D2, 1:4:8 using 20 mm graded stone aggregate, as in mass concrete etc., complete all as specified and as directed

M&L for 75 mm thick PCC 1:4:8, type D2, finished even and rough to receive top surfaces, complete all as specified and as directed.

M&L for Reinforced cement concrete, type A-1 (1:1½:3), using 20 mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, complete all as specified and as directed.

M&L for Reinforced cement concrete, type A-1 (1:1½:3), using 20 mm graded stone aggregates as in Chajjas, lintels and the like , complete all as specified and as directed.

Drilling holes of suitable size for passing tubes of any description into or through RCC cooking platform slab with stone or brick wall etc. and the like of thickness not more than 250 mm by electric drilling machine and making good , complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends, or edges of landings etc. and cutting chases for concealed water tubing, concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, in brick walls, complete all as specified.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, , complete all as specified and as directed.

M&L for brick work with fly ash bricks (old size bricks) straight or curved on plan exc 6m mean radius,built in cement mortar (1:4) , complete all as specified and as directed.

M&L for brick work with fly ash bricks (old size bricks) straight or curved on plan exc 6m mean radius,built in cement mortar (1:6) , complete all as specified and as directed.

M&L for Brick work using old size bricks (EXCEPT BRICKS) straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar (1:4) , complete all as specified and as directed.

M&L for Brick work using old size bricks (EXCEPT BRICKS) straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar (1:6) , complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) roofs surfaces of any description and in any position not otherwise specifically provided for , complete all as specified and as directed.

M&L for PCC 1:2:4 type B-2 (using 20m graded crushed stone aggregate) as in roof padding, finished fair and even without using extra cement, complete all as specified and as directed.

M&L for providing APP based membrane course roof treatment in layers with following provisions :- (i) 20 mm thick (average) screed bed or bedding layer in CM (1:6) and finished the surface even & smooth without using extra cement on top of the roof surface. (ii) Applying one coat of bituminous primer, polymerized primer oil based coat, evenly @ 0.3 Kg/Sqm as priming coat to the prepared surfaces, till the surfaces is properly impregnated and the solvent oil in the based primer shall be allowed to evaporated completely. (iii) Applying APP based pre fabricated with non-woven polyester reinforced membrane stabilised with fibre glass strands & top with grey mineral slates, not less than 3mm thick and not less than 3 Kg/Sqm by torch application method.

M&L for Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:4) using water proofing compound, complete all as specified and as directed.

M&L for Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6), complete all as specified and as directed.

M&L for Rendering 15mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on ceilling surface in cement mortar (1:3), complete all as specified and as directed.

M&L for Rendering 20mm thick cement plaster in two coats (each coat 10mm thick ) on fair faces of brick work in cement mortor 1:4, finished even and smooth (without using extra cement) on walls , complete all as specified and as directed.

Supply only Water proofing compound , complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone walls and ceiling ,chajja, landing etc including racking of joints hacking for key scrubbing down with water etc , complete all as specified and as directed.

M&L for applying three coat of white wash on new surface of ceilling , complete all as specified and as directed.

M&L for applying two coat of white wash on old surface of ceilling, complete all as specified and as directed.

M&L for applying two coat of white wash on old surface of wall , complete all as specified and as directed.

M&L for two coats of Oil bound distemper on old surface of wall and preparation to oil bound distempering including complete preparation of existing surfaces and apply 3mm thick wall putty, complete all as specified and as directed.

M&L for two coats of oil bound distemper on new surface of wall including chalk whiting, preparation to distempering, complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over chalk whiting, complete all as specified and as directed.

M&L for preparation of new plastered surfaces or unplastered surfaces of walls and applying two coats of cement base paint , complete all as specified and as directed.

M&L for applying 3 mm thick wall care putty on wall surfaces complete all as directed.

M&L for 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate, finished rough, as in floors, complete all as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surfaces of size 300x200x6-7mm thick quality not less than group II, straight edge, on skirting , dados, walls etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 10mm thick rendering in cement mortar 1:6, complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles in vertical surfaces of size 350x250x7mm/450x600x7mm thick quality not less than group II, straight edge, k, as on skirting , dados, walls etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 10mm thick rendering in cement mortar 1:6, complete all as specified and as directed.

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.18 Sqm but n. exc 0.38 sqm in floors etc , over & including 15 mm thick cement mortar (1:6) screed etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.18 Sqm but n. exc 0.38 sqm on vertical surfaces such as dado & skirting & including 10 mm thick cement mortar (1:4) screed set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for Non-skid ceramic coloured tiles, straight cut/joint free, 7-8 mm thick , area of each tile exceeding 0.06 Sq.m but not exceeding 0.11Sq.m, in floors & skirting etc. over & including 15 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry & pointed with grout of matching shade,including dismantling of tiles, complete all as specified and as directed.

M&L for Factory made PCC type M-35 paving interlocking tiles of 60 mm thick, pre- polished finished, ISI marked, with grey cement & pigment, of shape approved by GE, in paths, complete all as specified and as directed.

M&L for Factory made PCC type M-35 paving interlocking tiles pre- polished finished, ISI marked, with grey cement & pigment, 60 mm thick, of shape approved by GE, in paths, over & including 15 mm thick cement mortar (1:4) screed, set, jointed and pointed with grey cement slurry over, complete all as specified and as directed.

M&L for Chequered Cement concrete tiles 20cm x 20cm x 25mm thick, set jointed and pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar 1:6, with grey cement and pigment, complete all as specified and as directed.

M&L for sand cushion filling for floor,foundation etc including watering and consolidation , complete all as specified and as directed.

M&L for hardcore broken stone or boulder of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed.

Taking down chowkhats or frame not exceeding 1.5 Sq. m each with shutter(s) (without taking off shutters from the frame), including removing to store, complete all as specified and as directed.

Taking down chowkhats or frame exceeding 1.5 Sq. m but not exceeding 4 Sq. m each with shutter(s) (without taking off shutters from the frame), including removing to store, complete all as specified and as directed.

Taking down shutters of any description not exceeding 1 Sq. m each, including stacking at directed location for refixing and/or removing to store, complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm but not exceeding 2 Sq. m each, including stacking at directed location for refixing and/or removing to store, complete all as specified and as directed.

M&L for 35mm thick 2nd class hard wood, glazed & skeleton shutters, open rebated & prepared to receive glass, (two panel to receive wire gauge) gauge etc, edges of framing plain, chamfered as rounded fitted with cut and mitere beads for securing etc , complete all as specified and as directed.

M&L for Factory made, 35 mm thick, panelled shutter second class hard wood, plain framed, hammer marked, with lock rail . The size of rail and style as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated , complete all as specified and as directed.

S&F Factory made, flush shutters of 25 mm thick, solid core construction with block board core and plywood face panels, commercial type on both sides, ISI marked, complete all as specified and as directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain PVC sheet reinforced with M.S. Square tube, complete all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail includning butt hinges, complete all as specified and as directed.

S&F anodized Aluminium barrel tower bolts of extruded section 150 mm long, dia of bolt not less than 10 mm, ISI marked, complete all as specified and as directed.

S&F mild steel Butt hinges of 100 mm size, medium weight, cold rolled and fixed with screws or with welding to existing MS frames, ISI marked, complete all as specified and as directed..

S&F anodized Aluminium sliding door bolts with hasp staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium, 250 mm long and dia of rod not less than 16 mm, ISI marked, complete all as specified and as directed.

S&F Aluminium handles, cast type anodized of size 150 mm, ISI marked, complete all as specified and as directed.

S&F Hasp and staple 100mm of aluminimum anodised with hinges including bolt to hinge plate and fixed with screws, complete all as specified and as directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

S&F Drapery rod (conduit) of dia not less than 25 mm having a corrugated virgin PVC extrusion on it finials of approved shade with standard MS powder coated/ brackets, fixed to walls with rawl plugs and steel screws, complete all as specified and as directed.

M&L for Framed work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-410-O or Fe-310-O, complete all as specified and as directed.

M&L for Mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips ,complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazinjg bars, dovetailed or welded, including one shop coat of red oxide zinc chrome primer , complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded, including one shop coat of red oxide zinc chrome primer , complete all as specified and as directed.

S&F in repair's Factory made steel ventilator with top hung shutters, dovetailed or welded including hinges, steel handles, etc. with fixed type including one shop coat of red oxide zinc chrome primer, complete all as specified and as directed.

M&L for Two coat of synthetic enamel paint over old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces, complete all as specified and as directed.

M&L for Two coats of synthetic enamel paint over & including a coat of pink primer over new wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth including preparation of surfaces , complete all as specified and as directed.

M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over new steel & iron surfaces of any description not otherwise described, over 10 cm in width or girth, including preparation of surfaces , complete all as specified and as directed.

M&L for Plain Sheet glass 3 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane, complete all as specified and as directed.

M&L for Figured glass 4 mm thick, pin head type and glazing with oil putty in squares not exceeding 0.5 sq. m in each pane, complete all as specified and as directed.

M&L for GI Tube of 15 mm bore, ‘medium grade’ with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Fixing only GI Tube of 15 mm bore with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.

Taking up or down steel tubing 15 mm bore and connections, including cleaning for re-fixing or removal to store , complete all as specified and as directed.

S&F CP stop valve suitable for 15 mm bore pipe, complete all as specified and as directed.

S&F in repair's Bib taps, cast copper alloy with handle, chromium plated fancy type, short body with wall flange screwed down suitable for 15 mm bore pipe, complete all as specified and as directed.

S&F in repair's Consealed stop valve, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed suitable for 15 mm bore pipe,, complete all as specified and as directed.

S&F Cast copper alloy chromium plated towel rail of 450 mm long, complete all as specified and as directed.

S&F in reapir's Cast copper alloy, chromium plated long neck pillar cock suitable for 15 mm bore pipe, complete all as specified and as directed.

S&F in repair's Waste coupling of PTMT for WHB any colour half or full threaded suitable for 32 mm size discharge pipe (Minimum weight 45 gm) , complete all as specified and as directed.

S&F in repair's PVC waste pipe 800 mm long suitable for 32 mm dia waste coupling, complete all as specified and as directed.

S&F in repair's CP Swivel shower arm 15mm bore 195 mm long with bend of 45 degree with flange for fixing with 15mm pipe (Minimum weight 40 gm) , complete all as specified and as directed.

S&F in repair's PTMT shelf 450 mm x 124 mm any colour with brass chromium plated screws & PVC rawl plugs (Minimum weight 300 gm) , complete all as specified and as directed.

S&F in repair's Hat and coat hooks, solid body Aluminium 175mm to 250 mm fixed to wall with screw and rawl plugs, complete all as specified and as directed.

S&F in repair's PVC connection pipe of 15 mm bore with PTMT nuts of length 450 mm, complete all as specified and as directed.

S&F Cast iron soil, waste and vent pipes, sand cast pipe of 75mm bore , ISI marked (IS:3989), in any length with or without ears, with cement joints, fixed to walls including mild steel clamps, complete all as specified and as directed.

S&F Cast iron soil, waste and vent pipes, sand cast pipe of 100mm bore ,ISI marked (IS:3989), in any length with or without ears, with cement joints, fixed to walls including mild steel clamps, complete all as specified and as directed.

S&F Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured) suitable for 75 mm bore spun pipes, ISI marked, complete all as specified and as directed.

S&F Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured) suitable for 100 mm bore spun pipes, ISI marked, complete all as specified and as directed.

S&F in repair's Cast iron 'P' or 'S' trap, ISI marked, suitable for 100 mm bore CI spun pipes , complete all as specified and as directed.

S&F 100 mm bore cast iron sanitary connection socket to fit WC outlet , complete all as specified and as directed.

S&F in repair's PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore, including jointing to waste pipe set in cement concrete type B-1(1:2:4) of size 200 mm x 200 mm x 250 mm, complete all as specified and as directed.

S&F in repair's kitchen sink made of stainless steel 1mm thick with plugs, washers and wastes; including bedding in cement mortar & providing cantilever brackets and west pipe, overall size 495mm x 420mm and bowl size 410mmx 330mm x160mm , complete all as specified and as directed.

S&F in repair's Kitchen plate rack made of stainless steel not less than 1mm thick with fixing acessories of size 900mm x 900mm x 250mm, complete all as specified and as directed.

S&F in repair's Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, white with integral foot rests (excluding flushing cistern and flush pipe) , complete all as specified and as directed.

S&F in repair's 10 ltr capacity PVC flushing cistern syphonic action type white (IS 7231) marked with flush pipe with all fixing arrangements, complete all as specified and as directed.

S&F in repair's Vitreous China wash basin, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts, complete all as specified and as directed.

S&F 110mm dia PVC rain water pipe fixed to wall set in cement mortar with and including MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc complete all as specified and as directed.

S&F Low density polythene pipes of dia 50mm bore (LDPE) of pressure rating 6 Kgf/cm2 fixed to walls, ceiling or in floor etc, complete all as specified and as directed.

M&L for Form work to sides and soffits of floor roof beams, beam haunching , girders, bressummers lintels, cantilevers, shelves including supports, edges, over hangs, splays etc splays between floors and beams etc , complete all as specified and as directed.

S&F PVC bends plain (any radius) for 110mm bore PVC pipes, complete all as specified and as directed.

M&L for granite any type 20mm thick table rubbed and polished in step ,jambs,cooking plat form etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment , complete all as specified and as directed.

Demolition of stone slab and tile of any description , complete all as specified and as directed.

M&L for Reinforced concrete pipes 150mm bore class NP2 laid and jointed with collars , complete all as specified and as directed.

M&L for cement concrete bed of 1:3:6 type C-2 to 150 mm bore drain pipes including packing under ,and hunching against the sides of pipes after they laid and tested , complete all as specified and as directed.

M&L for cement concrete type B0 1:2:4 (12.5mm graded stone aggregade) for coping,plinth course etc complete all as specified and as directed.

M&L for RCC in type B-0 1;2:4 (12.5mm graded aggregade) such as cover slab and similar work, complete all as specified and as directed.

Demolition and breaking up drain pipes (salt glazed ware,AC or rein forced concrete set in cement mortor, compete all as specified and as directed.

Dismantling of wall or ceilling boards of any thicness including cover fillets, compete all as specified and as directed.

S&F 605mm x 605mm Anodised aluminium snap grid frame work for false ceiling with all necessary aluminum angle & Tee arrangement with and incl fixing cleats screws etc ,complete all as specified and as directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and as directed.

S&F for 4mm thick 'E' board (non asbestos fibre) plain building boards fixed in aluminum frame work in ceiling flat or sloping with screws complete all as specified.

S&F Anodised aluminium door shutters, , aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprane packing, handles 2 Nos in each door, hinges, anodised alumnium snap beading, screws etc. complete all as specified and as directed.

S&F Anodised aluminium ,window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised etc, complete all as specified and as directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq.m in each pane, complete all as specified and as directed.

S&F Solar control film 50 micron relfective type sticked to glass panes as per instructions of manufacturers, complete all as specified and as directed.

S&F Anodised aluminium frame for doors, windows ventilators with one or more rebates including deco grill and joining cleat for fixing etc, complete all as specified and as directed.

S&F Door closer hydraulically regulated, alluminium body, designation No. 3 universal type, suitable for door shutters upto 851 to 1000 mm in width and of weight between 60 to 80 kg, ISI marked, complete all as specified and as directed.

S&F Mortice lock, alluminium body, 4 lever, 150 mm size, vertical type with two keys , complete all as specified and as directed.

S&F Aluminium wire mesh 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminiun beads ,complete all as specified and as directed by EIC

S&F aluminum anodised GRILL fixed with suifable 'F' section No. 8584 15.30 x 23.40 x 1.40mm fabricated and rivetted to aluminum windows, complete all as specified and as directed by Engr-in-charge. Make: Deco grill DG 103 of M/s Associated Profiles & Aluminum Ltd or Equivalent

S&F in repair's 9mm particle board ,mediun density ,flat presed,single layer with BWR type fixed with nails or frame work , complete all as specified and as directed.

Hacking out old broken glass (any thickness, size,quality or description) from wooden frames/ glazed with putty or fixed with beads, complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, flat or curved incl ridges hips valleys as in roof coverings, complete all as specified and as directed.

M&L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and as directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Dismantling wrought Iron or mild steel work of any description not otherwise provided for wind tie, complete all as specified and as directed.

M&L for wind ties fixing for roof including securing bolts,flat iron fillets for securing weather boarding with screw bolts and nuts including all necessary drilling,bolting or riveting, etc and similar work conforming to Fe 410-0 or Fe 310-0 including painted with one soap coat of zinc chromate primer paint including preparation of surface at contractor's workshop before fabrication, complete all as specified and as directed.

M&L for Preparation of wood & wood based materials , new or old of any description and girth, not otherwise described and treated with one coat of creosote oil, complete all as specified and as directed.

Dismantling of timber scantlings 40 sq.cm and over in section, in any position, complete all as specified and as directed.

M&L for clean sawn second class hardwood in scantling for purline & rafter etc, complete all as specified and as directed.

S&F Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed.

S&F in repair's Alumn Curtain Rods 25mm dia Decorative type with a pair of brackets, powder coated of approved pattern and colour, complete all as specified and as directed.

M&L for steel surface applied one coat of synthtic enmal paint surface of any description, over 10cm in with or grith, complete all as specified and as directed.

E/M Portion

Taking down carefully aluminium/copper conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing, complete all as specified and as specified.

Material and labour for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FR cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FR PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc, complete all as specified and as directed.

All as per item No. 2.002 here-in-before but One 3 pin 5 Amps socket out let points on independent board, complete all as specified and as directed.

All as per item No. 2.002 here-in-before but 5 Amp socket on same board controlled with other switches, complete all as specified and as directed.

Material and labour for point wiring of socket outlet on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FR cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FR cable earth wire and connecting to earth dolly and brass screws, washers etc, complete all as specified and as directed.

Supply and fix switch piano flush type, single pole , 5/6 Amps, one way, complete all as specified and as directed.

Supply and fix switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch ,complete all as specified and as directed.

S&F socket outlets 2 in 1, 3 pin, 5/6 Amps flush type230/240 V , complete all as specified and as directed .( For Same Board only)

Supply and fix switch socket combination 5 in 1 , 6 pin , (5/16 Amps ) flush type controlled by one switch , complete all as specified and as directed.

Supply & fix ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps ,complete all as specified and as directed.

Supply & fix stepped type electronic fan regulator flush type 240 Volts ISI marked , complete all as specified and as directed.

Supply & fix Bell push , flush type , 5 amp , complete all as specified and as directed.

Supply & fix Buzzer, Ding dong, AC 230 Volts, single pole 230 volts, complete all as specified and as directed.

Supply & fix lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings, complete all as specified and as directed.

Supply and fix Modular switch 1 way 6 A, 1 module, complete all as specified and as directed.

Supply and fix Modular socket 6 A -2/3 pin combined, 2 Module , complete all as specified and as directed.

Supply and fix Modular Switch socket Combination 16A, 6 pin, 3 module, complete all as specified and as directed.

Supply and fix Modular white cover plate with frame 2 module, complete all as specified and as directed.

Supply and fix Modular white cover plate with frame 3 module , complete all as specified and as directed.

Supply and fix Modular white cover plate with frame 6 module, complete all as specified and as directed.

Supply and fix Modular white cover plate with frame 8 module , complete all as specified and as directed.

Supply & fix Modular fan regulator 120 W 2 module suitable for 230 Volts AC , complete all as specified and as directed.

Supply & fix Modular 20 Amps Power unit enclosure single pole and neutral with two pin and earth plug , complete all as specified and as directed.

Supply and fix recessed mounted 2' x 2' LED luminaire 42 watts for grid ceiling minimumm lumen output 100 lumen/Watt, pre-treated CRCA frame powder coated with diffused Profied including necessary connection , complete all as specified and as directed.

Supply and fix in repair's two single core 6 sqmm nominal cross sectional area multistranded copper conductor FR cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FR cable, PVC insulated unsheathed 1100 Volts grade earth wire, complete all as specified and as directed.

Supply and fix in repair's Building security light fittings 25 watts, minimumm system lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size, complete all as specified and as directed.

Supply and fix in reapir's 18 W LED light fitting wall mounted batten 4ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 20 watt,6000K including necessary connection, complete all as specified and as directed.

Supply and fix in reapir's 20 W LED light fitting wall mounted batten 4ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 20 watt,6000K including necessary connection, complete all as specified and as directed.

Supply and fix in repair's 9 W LED light fitting wall mounted batten 2ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection, complete all as specified and as directed.

Supply and fix Surface mounted type decorative light fitting 1 x 12W LED 6k 230V AC, 50Hz complete with all accessories, complete all as specified and as directed.

Supply and fix Surface mounted type decorative light fitting 1 x 10W LED 6k 230V AC, 50Hz complete with all accessories, complete all as specified and as directed.

Supply and fix LED Bulb 15 Watt suitable for batten holder, complete all as specified and as directed.

Supply and fix LED Bulb 12 Watt suitable for batten holder, complete all as specified and as directed.

Supply and fix in repair's bracket made out of galvanized tube 25mm bore (light grade) 1.20 meter long and band as required with MS clamps,nuts and bolts with one coat of red oxide primer and two coat of Aluminium paint, complete all as specified and as directed.

Supply and fix in repair's bracket made out of galvanized tube 25mm bore (light grade) 1.50 meter long and band as required with MS clamps,nuts and bolts with one coat of red oxide primer and two coat of Aluminium paint, complete all as specified and as directed.

Supply and fix in repair's epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact ,complete all as specified and as directed.

Supply and fix in repair's epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Triple pole and neutral 415 V, 4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact,complete all as specified and as directed.

Supply and fix epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Triple pole and neutral 415 V, 4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and as directed.

Supply and fix Vertical distribution board double door TPN 6 way with IP 54 multiphase outgoing suitable for mounting 100 Amps as incomer with Bus bars, Neutral links ,complete all as specified and as directed.

Supply and fix Vertical distribution board double door TPN 8 way with IP 54 multiphase outgoing suitable for mounting 100 Amps as incomer with Bus bars, Neutral links ,complete all as specified and as directed.

Supply and fix in repair's MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Volts to be housed in DBs including necessry connection, complete all as specified and as directed.

Supply and fix in repair's MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs including necessry connection ,complete all as specified and as directed.

Supply and fix in repair's MCB TPN 63 Amps, 'C' series 10kA, 415 Volts and to be housed in DBs including necessry connection, complete all as specified and as directed.

Supply and fix MCCB 4 pole , 415 volts of capacity 100 Amps with breaking capacity of 16 KA Fixed thermal and fixed magnetic setting including necessry connection, complete all as specified and as directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and as directed and testing on completion.

supply and fix in repair's 4 mm dia GI earth lead with clamp and connection with existing complete all as specified.

Supply & fix ceiling fan 1200mm size , star 5 rated, ISI mark, 240V, 50 Hz ,complete all as specified and as directed.

S&F ventilating exhaust fan 300 mm sweep 230 volt AC complete with louver and all accessories including cutting hole of suitable size, making good surface with plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size, complete all as specified and as directed.

Supply & fix PVC Exhaust ventilation fan of sweep 250 mm sweep, 230volt AC complete with louver and all asssesories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing connected with rwin core twisted flexible copper conductor (23/0.0076) of size complete all as directed by Engr-in-Charge.

Taking down of AC ceiling fan of any sweep & any height and opening the fan and oiling, greasing and replacement of unserviceable accessories and servicing, complete overhauling and re-assembling and testing complete for efficient functioning and hanging it back in position including provn of 0.5 Sqmm copper flexible twin twisted cable (length not exceeding 0.5 metre) from ceiling rose to fan as directed by the Engr-in-Charge. (Note : Accessories such as Capacitor shall be measured and paid under relavtive item here-in-after).

M&L for painting of ceiling fans upto 1400mm sweep carefully, dismantling fan blades and paint with one coat of synthetic enamel paint including filling cavities with filler after cleaning all dust etc ,complete all as specified and as directed.

Supply only capacitor 2.5 MFD ,complete all as specified and as directed.

Supply and fix Geyser 25 Ltrs with accessories, complete all as specified and as directed

Supply, laying / fixing / connecting, testing and commissioning of LT under ground cable of 120 Sqmm x 3.5 core XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely.

Supply, laying / fixing / connecting, testing and commissioning of LT under ground cable of 50 Sqmm x 3.5 core XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely.

Supply, laying / fixing / connecting, testing and commissioning of LT under ground cable of 25 Sqmm x 3.5 core XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil, complete all as specified and as directed.

Removing excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and as directed.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . Note :- Punned thickness 18 cm shall only be considered for payment

Supply and lay in trenches fly ash bricks, for cable protection ,complete all as specified and as directed by the Engr-in-Charge.

Parallal boring under roads in conventional method without disturbing the top surface of the road for passing of cable protection pipe etc ,complete all as specified and as directed.

S&F in repair's GI Pipe of 50 mm bore “light grade”including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement , complete all as specified and as directed.

Supply , install, testing and commissioning of LT Feeder pillar Box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubical , fully compartmentalized type , weather proof , protection IP 52 , suitable for outdoor use with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick with CPRI Approved CRCA steel sheet with angle iron frame work and legs of ISA 50X50X5 mm with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs with sloping canopy at top , double hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated , complete all as specified and directed :- BUSBAR :- Copper bus bar 600 Amps , supported on non hygroscopic fibres and brass screws for mounting -04 Nos INCOMER:- MCCB 4 pole 415 Volts of breaking capacity of 35 KA of 400 Amps with Fixed thermal and Fixed magnetic setting- 01 Nos INDICATING DEVICES:- (a) LED Indicating lamps for Main Supply indicating R, Y, B - 03 Nos (b ) Digital Ampere Meter 31/2 digit display , incl CT having CTR 400/5 - 01 Nos & Digital Voltmeter 0-500 Volts , SIF 96 - 01 Nos OUTGOING FEEDERS:- (a) MCCB 4 pole 415 Volts of breaking capacity of 16 KA of 100 Amps with Fixed thermal and Fixed magnetic setting - 06 Nos (b) MCB of 4 pole , 415 volts of capacity 40 amps with breaking capacity of 10 KA - 04 Nos (c) Time switches 415 V three Phase of 20 Amp rating with contactor fitted inside steel enclosure - 01 Nos

S&F rotational moulded polyethylene water storage tanks of capacity 500 Ltrs (Cylindrical, vertical with closed top with three layered) confirming to relevent IS complete including provision of all inlet outlet overflow and drain pipe fitting including taking down old unserviceable tank, complete all as specified and as directed by Engineer in Charge.

Supply and fix high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 25 mm dia with fly nut complete including taking down old unserviceable one, complete all as specified and as directed by Engineer in Charge.

M&L for 25 mm bore gate valve cast copper alloy screwed down high pressure with clutch handle screwed both ends for Iron pipe including taking down old unserviceableone, complete all as specified and as directed.

Supply & fix in repair's 25 mm bore GI Tubing medium grade in Trenches/ Floor/Pillar and connection including fitting like socket /Union/Tee/Reducer Nipple etc complete all as per specified and directed.

Schedule 'A' Part II Schedule of Credit

M/s Bhola Shah Bansi Lall

UNITED BUILDERS

NEW JUPITER CONSTRUCTION