PROVN OF OPERATIONAL ROOM OF 3 SECTOR RR AT MANASBAL, PROVN OF TOILET BLOCK OC R CENTRE SONAMARG (LOWER GRN) AND SPL REP TO BLDG NO P-08 AND P-04 UPPER GRN DET 15CESR AT SONAMARG UNDER GE 970 EWS

Amount

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out for hard/dense soil complete all as spd and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil.

Removing excavated material/soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed

M&L cement concrete 1:4:8 type D2 (40mm graded stone aggregate) in foundations, filling and mass concrete.

Use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat and rough finished surfaces of concrete complete all as spd and directed.

Use & waste formwork to sides of pillars, posts, struts, piers, columns, and stanchions square, rectangular or polygonal and rough finished surfaces of concrete complete all as spd and directed.

Use & waste formwork to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc flat and rough finished surfaces of concrete complete all as spd and directed.

M&L for RCC (Nominal Mix) Type B1, 1:2:4 using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (Nominal mix) Type B1,1:2:4 using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC (Nominal mix) Type B1, 1:2:4 using 20 mm graded stone aggregate in beams, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC (Nominal mix) Type B1, 1:2:4 using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S & F TMT bars 10 mm dia and over, cut to length, bent to shape as required incl cracking bending hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed

Descrition all as per ser item No 12 above, but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders etc.

M&L brick work with sub class 'B' modular brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 complete.

M&L brick work with sub class 'B' modular brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 is to be finised even and smooth (without using extra cement) internally complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coat of distemper oil emulsion OBD white or tinted in wall internally complete all as specified and directed.

M&L for 3mm thick wall care putty on internal wall complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in CM 1:4 is to be finised even and smooth (without using extra cement) complete all as specified and directed.

M&L for preparation of new plastered surface and finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work( Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10Sqm complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63mm (broken stone or boulders), deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as spd and directed

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as spd and directed

M&L for 100mm thick Cement concrete for sub base type D2, 1:4;8 (using 40 mm graded aggregate) complete all as specified and directed.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6) as specified and directed.

S&F light shade vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6) as specified and directed.

M&L for glazed ceramic coloured tile for vertical surfaces of size 300x200x6mm thick , set and jointed in neat cement slurry and pointed in white or colour cement to matched including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling all as specified 605 x 605mm

S&F Providing and fixing Gypsum Board 10mm thick decorative type in ceiling fixed with screw as per manufacturers instructions all as specified

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate) and finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as spd and directed.

S&F mild steel rolled sections as in roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. ( Fe 410-W (Gde E-250) quality A) complete all as spd and directed.

S&F Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde- E- 250) quality- A, complete all as spd and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for preparation of new steel and iron surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

S&F Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handels 2 Nos in each door, hinges, anodised alumnium snap beading, screws etc. complete all as specified

S&F Anodised aluminium window & ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S & F Powder Coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portion) with extruded built up standered tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions i.e, at top, bottom and sides with requried EPDM rubber/ neoprene gasket etc. Aluminimum sections shall be smooth, rust free straight, mitred and jointed mechanically wherever required including cleat angle, Aluminimum snap beading for glazing/paneling C.P. brass/stainless steel screws, all complete as per architectural drawings and the direction of Engineer-in-Charge

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as spd and directed.

S&F Brass 2 levers Mortice lock, vertical type, size 100mm

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor (140mm size) complete all as specified and directed

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & directed (Make : Rajshree)

M&L Factory made solid panel of PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. (Make: Rajshree or equivalent)

S&F Sheet glass 5.5mm thick, ordinary quality & glazing with oil putty in square exc 0.5 sq.m in each pane including hacking out old broken glass (any thicknesss, size,quality or description) from metal frame inlcuding punching or drilling out old glazing pins/spring clips & providing & fixing new ones

S&F Sheet glass 5.5mm thick, ordinary quality & glazing with oil putty in square n.exc 0.5 sq.m in each pane including hacking out old broken glass (any thicknesss, size,quality or description) from metal frame inlcuding punching or drilling out old glazing pins/spring clips & providing & fixing new ones

M&L 16mm outer dia for 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as pecified and directed.

M&L 20mm outer dia for 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as pecified and directed.

M&L for vitreous china bowl urinal flat back, size 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed. (Make : Hindware or equivalent)

M&L for vitreous china wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed. (Make: Hindware or equivalent)

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe,antisyphonage pipe, etc complete all as specified and directed.

M&L for PVC valveless, syphonic action type, flushing cistern, 10 ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets and including flushing pipe 32 mm dia of bore, high density polyethylene pipes of pressure rating 6 kg/sqcm complete all as specified and directed

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed

M&L for 15mm dia of bore stop valves, fancy type, chromium plated, screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed.

S&F 15mm Pillar taps, cast copper alloy, with capstand heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15 mm size pipe complete all as specified and directed.

M&L for Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms) complete all as specified and directed.

M&L for Soap dish, vitreous China white, approximate size 160x160x90mm complete all as specified and directed

M&L for 110mm PVC (SWR) pipes, single socketed, in any length, with rubber rings joints, laid in trenches or in floors completed all as specified and directed

M&L for 75mm PVC (SWR) pipes, single socketed, in any length, with rubber rings joints, laid in trenches or in floors completed all as specified and directed

M&L for 75mm dia of bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed

M&L for 110mm PVC (SWR) bends any radius complete all as specified and directed

M&L for 75mm dia PVC (SWR) vent cowl complete all as specified and directed

M&L for 110mm dia of bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed

M&L for 75mm dia of bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed

S&F brass chromium plated Tubular towel rail, 20 mm dia, D type, 60cm long between flanges complete all as specified and directed.

M&L for 20mm dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F Waste coupling of PTMT 32mm size (half or full threaded) . suitable for urinals and wash basin (Minimum weight 32mm-45gms complete all as specified and directed.

S&F grating doom 100mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

S&F 1000 litre capacity, double layered rotational moulded polythylene water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge.

Sockage well excavation in any type of soil, 1.8m dia x 30m effective depth of foundation in PCC 1:3:6, walls of honeycomb masonary with top ring of M25 concrete including intercepting chamber and screen chamber made on brick masonary in CM, RCC cover slap in M25, interconnecting pipe of RCC, DWC complete filled with brick bat of size 1.8m dia X 3m depth complete all as specified and as dierected.

On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent soft, connection etc. Complete for 25 users (Conventional type) complete all as specified and as dierected.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165

M & L for Cement concrete 40mm thick type B-1, 1:2:4 (20mm graded aggregate) as in level course.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates ( Fe 410-W (Gde E-250) quality A) complete all as spd and directed.

Dismantling plain or corrugated steel sheeting, any guage, thickness

Demolition of cement concrete ground floor unreinforced and paving n.exc 15cm thickness (below or above ground level) all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, complete all as specified and directed by Engineer-in-Charge.

M & L Preparation of newly plastered surface and apply two coat of cement base paint over a coat of Priming paint complete all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) exc. 1.50 Sqm but n exc. 4 Sqm each complete and all as specified.

Taking down chowkhat with shutters (without taking off shutters from the frame) not exc. 1.50 Sqm complete and all as specified.

M&L for Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or weldedcomplete all as spd and directed

S&F for Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded complete all as specified and directed.

M&L for 200mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed

4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed

Dismantling of stone slabs a laid in dry and tiles of any description or thickness in floors and incl removal of out side MoD land and all complete all as specified.

M&L for 50mm thick sand cusion under layer of floor complete all as specified.

Material and labour for machine pressed precast concrete interlocking paver block any shape, colour , size and pattern as approved by GE conforming to IS 15658-2006 of 60 mm thick, M-35 Grade & glossy finish with coloured cement and pigment all in specified and directed.

Dismantling wall and ceiling board (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M & L 9mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and directed

Taking down cement plaster or brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water all as specified and directed

M&L 15mm thick rendering on fair faces of brick work or concrete sufaces in CM 1:4 including finishing even and smooth without using extra cement and by mixing WPC @ 3% of Cement Constant complete all as specified and directed. Note WPC used will be measured and paid separately.

Supply only water proofing compound, complete all as specified and directed.

M&L preparation of plastered or uplastered new surfaces on walls and applying two coats of oil bond distemper on walls over 3mm thick of wall putty all as specified and directed

M&L for 25mm thick Cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate in leveling course of floor etc, finished even & rough to complete and all as specified.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F plain , solid , straight chowkhat and frames , wrought , framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints in 2nd class Hard wood complete all as specified.

S&F 1st class hard wood 35mm thickness Glazed and skeleton shutters ( Factory made), open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all a specified and directed.

S&F 30mm thick Flush shutters solid core construction with Block board and plywood face panels commercial type both side complete all a specified and directed.

M&L for prep for newly treated or untreated wooden surface and applying two coats of snthetic enamel paint over a coat of pink primer complete all as specified and directed

Hacking out old broken glass (any thicknesss, size,quality or description) from metal frame inlcuding punching or drilling out old glazing pins/spring clips and providing and fixing new ones

S&F in repairs 3mm thick tinted glass ordinary quality and glazing with oil putty in square exc. 0.5 Sqm in each complete and all as specified and directed

S&F 100 mm long aluminium tower bolt, complete and all as specified.

S&F MS 100 mm size butt hinges medium wt. of cold rolled complete and all as specified.

Aluminium handles, cast type anodised 75mm size complete all as specified

S&F Stainless repairs of steel wire cloth.0.56 mm normal dia of wire and average width of aperture 1.40 mm complete and all as specified and directed

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mtr mean radius, built in cement mortar 1:4 as in manhole, wall, drain etc complete all as specified and directed by Engineer-in-Charge.

S&F 300 mm long brass, sliding door bolt with or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolt and fixed all as specified.

M&L for 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub bases, finished even & rough to receive finishing layer, etc. complete.

M&L for RCC (design mix) M-30 (20mm graded aggregate) in Slabs including on beams, columns, etc.; basement slabs, underreamed piles and mass concrete complete all as specified and directed.

M&L for Rendering 10mm thick on fare faces of brick work or concerete surfacec in CM 1:6, finish even and smooth without using extra cement complete all as specified and directed.

S&F steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and directed.

S&F for sheet glass 3mm thick ordinary quality and glazing with oil putty/beads in square n.exc 0.5 sqm in each pane complete all as specified and directed.

M&L for Corner Sheet Glass shelf assembly consisting of 5.5mm thick sheet glass shelf with CP bracket guard and complete all as specified and directed.

S&F for repair in Health faucet (ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS Wall hook incl making connections and fixed in position complete in all as specified and directed.

M&L for vitreous China squatting pan, `Long pan size 580 mm white, with 'p' or 's' trap, front back integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed .

S&F 500 litre capacity, double layered rotational moulded polythylene water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge.

M & L for Hangers 4/6mm dia.G.I. (upto 1200mm length) fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed

M & L 6mm thick Non asbestos fibre cement building boards (size of board 600x600mm) fixed or laid over anodised aluminium snap grid framework complete all as specified and directed

Material & labour for point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated multistranded, copper conductor cable (FRLSH) drawn through and including PVC concealed conduit 19/20 mm bore (ISI marked) and accessories (concealed in wall & surface in ceiling complete including cutting ,chases & making good disturbed surfaces), terminated in and including pressed steel terminal boxes with plastic laminated backlite sheet top cover 3 mm thick (hylum) fixed with nickel polished screws with washers, earth continuity PVC cable(FRLSH), copper conductor 1.5 Sqmm (nominal area) stranded with green insulation earth wire connected with earth dolly One light point / fan/exhaust point / bell push point controlled by one way switch 5 Amps and/or through regulator complete all as specified and directed.

Material & labour for point wiring complete with single core 2.5 Sqmm (nominal area) PVC insulated multistranded, copper conductor cable (FRLSH) drawn through and including PVC concealed conduit 19/20 mm bore (ISI marked) and accessories (concealed in wall & surface in ceiling complete including cutting ,chases & making good disturbed surfaces), terminated in and including pressed steel terminal boxes with plastic laminated backlite sheet top cover 3 mm thick (hylum) fixed with nickel polished screws with washers, earth continuity PVC cable(FRLSH), copper conductor 2.5 Sqmm (nominal area) stranded with green insulation earth wire connected with earth dolly for One power Point controlled by one way switch 15 Amps and/or through regulator complete all as specified and directed. complete all as specified.

Material & labour for point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated multistranded, copper conductor cable (FRLSH) drawn through and including PVC concealed conduit 19/20 mm bore (ISI marked) and accessories (concealed in wall & surface in ceiling complete including cutting ,chases & making good disturbed surfaces), terminated in and including pressed steel terminal boxes with plastic laminated backlite sheet top cover 3 mm thick (hylum) fixed with nickel polished screws with washers, earth continuity PVC cable(FRLSH), copper conductor 1.5 Sqmm (nominal area) stranded with green insulation earth wire connected with earth dolly for One 3 pin socket outlet, 5 amps, independent controlled by one way switch 5 Amps and/or through regulator complete all as specified and directed. complete all as specified.

Material & labour for point wiring complete with single core 4 Sqmm (nominal area) PVC insulated multistranded, copper conductor cable (FRLSH) drawn through and including PVC concealed conduit 19/20 mm bore (ISI marked) and accessories (concealed in wall & surface in ceiling complete including cutting ,chases & making good disturbed surfaces), terminated in and including pressed steel terminal boxes with plastic laminated backlite sheet top cover 3 mm thick (hylum) fixed with nickel polished screws with washers, earth continuity PVC cable(FRLSH), copper conductor 4 Sqmm (nominal area) stranded with green insulation earth wire connected with earth dolly for One 3 pin socket outlet. 15 amps, independent controlled by one way switch 15 Amps and/or through regulator complete all as specified and directed. complete all as specified.

M & L for Switch socket combination 3 pin 16A, flush type complete all as specified and directed.

Supply and fixing of Switch socket combination 2 in 1, 5 A flush type

Supply and fixing Switch Piano, flush type single pole, one way 5 Amp

M&L Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specified.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fixing of Single Pole and Neutral, Single Door, 240 V, 8 way Sheet Metal Enclosure for MCBs complete all as specified and directed.

Supply and fixing of SPN 32 Amp, 240V, 10KA 'C' curve miniature circuit breaker (MCB) complete with connection testing and commissioning.

Supply and fixing of SP 5 to 32 Amp, 240V, 10KA 'C' curve miniature circuit breaker (MCB) complete with connection testing and commissioning.

M & L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion.

M & L of Air termination, single pointed aluminium rod 12mm dia and 300mm long complete all as specified.

M & L of Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified

Supply & fix of Air Circulator fans 230 volts single phase oscillating of sweep size 400 mm suitable for wall mounting.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.complete all as specified.

Taking down unserviceable any type of Main Switch, DB's including MCBs incl wooden/GI/MS sheet board etc and removing from site and making good the disturbed surface of wall etc all as specified and as directed.

Taking down and M&L for one point wiring with PVC insulated un-sheathed cable with stranded copper conductor FR-LSH conforming to IS : 694 of size 1.5 Sq mm single core, including one No. 1.5 Sq mm single core PVC insulated un-sheathed copper cable FR-LSH as continuous earth wire drawn in and including PVC Casing & Caping double lock type of as required width (not less than 20 mm in width) ISI marked medium grade white colour with all accessories of same grade fixed on wall/ceiling including terminated in to Cast iron/pressed steel terminal box 60mm deep of required size made out of 2mm thick MS sheet duly painted both sides with 3 mm thick plastic laminated sheet top cover fixed with brass screw & cup washers for mounting switches, fan regulators etc for one light/fan/exhaust fan point/5 amp switch socket controlled by one 5 Amp switch one way complete all as specified and as directed

Taking down and M&L for surface point wiring with PVC insulated un-sheathed cable with stranded copper conductor FR-LSH conforming to IS : 694 of size 2.5 Sq mm single core, including one No. 2.5 Sq mm single core PVC insulated un-sheathed copper cable FR-LSH as continuous earth wire drawn in and including PVC Casing & Caping (double interlock type) of as required width (not less than 20 mm in width) ISI marked medium duty, white colour with all accessories of same grade, fixed on wall/ceiling including terminated in to Cast iron/pressed steel terminal box 60mm deep of required size made out of 2mm thick MS sheet duly painted both sides with 3 mm thick plastic laminated sheet top cover fixed with brass screw & cup washers for mounting switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type on the independent board complete all as specified and as directed

Taking down and M&L for Sub Main wiring using FRLS Insulated unsheathed, multistrand copper conductor FRLS PVC cable 2 runs of size 6 sqmm for phase and neutral and 6 Sq mm for earthing. drawn through rigid PVC conduit of suitable size fixed on wall/ground/Ceiling etc., and complete all as directed by Engr-in-Charge. Note: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length.

S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting of LED lamp 9 watt complete all as specified and directed.

S & F MCB DB SPN 4 way, 230 Volt with double door type modular type complete all as specified and as directed.

S & F in repairs LED lamp 1 x 9/11 watts suitable for pin type batten/pandent holder complete all as directed.

S&F in repair 1x20 W LED 6000K (4 ft) decorative ultra slim sqare profile linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient, extruded aluminium body heat shrink, provided for efficient dissipation and integrated electronic driver complete with lamp.Complete all as specified and as directed

Material & labour for point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated multistranded, copper conductor cable (FRLSH) drawn through and including PVC concealed conduit 19/20 mm bore (ISI marked) and accessories (concealed in wall & surface in ceiling complete including cutting ,chases & making good disturbed surfaces), terminated in and including pressed steel terminal boxes with plastic laminated backlite sheet top cover 3 mm thick (hylum) fixed with nickel polished screws with washers, earth continuity PVC cable(FRLSH), copper conductor 1.5 Sqmm (nominal area) stranded with green insulation earth wire connected with earth dolly One light point / fan/exhaust point / bell push point controlled by one way switch 5 Amps and/or through regulator complete all as specified and directed.

Description all as per ser item No 145 above, but socket out let 3 pin, 5 Amp on same board with other switch.

Description all as per ser item No 145 above, but socket out let 3 pin, 5 Amp on independent board with other switch.

Description all as per ser item No 145 above, but with 2.5 sqmm copper conductor cable for socket out let 3 pin, 15 Amp on independent board with other switch.

Supply and fixing socket out let 5 Amps 3 pin flush type for the same board complete all as specified and directed.

Supply and fix Fluorescent tube light fitting, LED batten with aluminium housing provided for efficient heat dissipation wirh polycarbonate diffuser and integrated electronic driver, 1x 10 watts 2 feet light fitting with white acrylic cover along with LED lamp white colour complete and connecteing electrically to ceiling rose using PVC insulated and overall sheated flexible copper conductor of size 0.75 Sqmm 3 core fixed complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2.of capacity 1.5 Ton all as specified and directed.

Supply and fix Voltage stablizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V - 270V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA.all as specified and directed.

Supply & fix Sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB up to 20 Amps, 240 volt capacity and tested on completion complete all as specified.

Supply & fixing for Sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 2.5 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on complete all as specified and directed. (Note : (i) 2 runs of 4 sqmm cable, 1 run of 2.5 sqmm single core copper cable and 1 run of non metalic PVC conduit shall be measured as single run. (ii) Cutting chasis and matching broken surface smoothly incl painting is included as one unit rate quantity).

M & L for cutting the existing GI Tubing of size upto 50 mm dia for taking new connection of 20 mm dia PPR Pipe complete with all fittings all as specified and directed.

M & L for PP-R Gate valves (brass insert) of outer dia 20 mm as specifed and directed.

River sand cushioning to underground cables 8cm thick before laying cable and 15cm thick after laying and streching the cable, complete all as specified and directed by Engr-in-Charge. Note :- For payment purpose punned thickness shall be measured

M/L for brick well burnt locally available sub class 'B' laid over sand cushioning to cable in trenches keeping width of brick parallel to the length of cable complete all as specified and directed.

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor gross sectional area 10 Sqmm , 2 core laid in trenches / duct / pipe etc complete all as specified and directed . (Note:- Earthwork & excavation shall be measured & paid separetely under respective items)

Notes :- Amount of Credit Schedule for Schedule 'A' Part-ll shall be deducted from total quoted amount of BOQ to arrive at the contract sum

M/S ABDUL KARIM RATHER (BID ID -3475254)

M/S GHULAM HASSAN KUCHAY (BID ID -3485475)