Renovation of 15 Gardens for Integrated Garden Development Program in TMC Limits under Basic amenity and development scheme Package 2.

Amount

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) Bd.A.1 Page No. 259

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ramming ,watering including shoring and strutting etc. complete. (Lift from 1.5m To 3.0 m.) By Mechanical Means

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. As directed by Engineer in charge.

Providing preconstructional antitermite treatment as per I.S.6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at1.0 percent of clorophyrif as per One Square Metre of surface area covering ten years guarantee on bond paper.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary) BR 4 Page No 104.105

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Bd.A. 12 Page No. 264

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, plywood/steel formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.E.2 Page No. 288 and B.7 Page No 38

Providing and laying Cast in situ/Ready Mix cement concrete M30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.3 Page No. 298 and B.7, Page No.38

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete. Bd.A.10 Page No. 262

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Bd.A.11 Page No. 263

Transportation of excavated earth including loading and unloading per truck trip of 6.00 cubic meter capacity per trip.

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Bd.F.8 Page Number 302 and B.7, Page Number38

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.9 Page No. 303 and B.7, Page No.38

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Bd.F.17, Page No. 306

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part3) -1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc.Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part3) -1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including strikingjoints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Bd.L.7 Page No. 369

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete. Bd.L.2 Page No. 368

Providing internal cement plaster 6mm thick in a single coat in cement mortar 1:3 with out neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

Providing and applying plaster with plaster of paris in 6 mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete.

Providing and applying Royal Luxury Emulsion of approved make on internal wall surface as detailed be low Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10% or waterby 15 to 20% allowing to dry for 6 to 8 hours After applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity.Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45 % or 65 to 70% by role Applying paints Royal eluxury emulsion 2nd coat with brush with water content 40 to 45 % or 65 to 70 % by roller. (With prior approval of S.E.)

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram / 15l). plaster crack should be filled by Acrylic base Crack seal / Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise on site technical reports from the concerned company technologist.

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. Spec. No.:As directed by Engineer-In-Charge.

Providing and applying a base coat comprising of 1Kilogram Polydee-MC and 1 Kilogram fresh cement after wetting the surface followed by drying the surface for 2 days, apply primer coat of TP-40 and after drying, applying Polydee-11 two component (mixingratio2A:1B)) Anti bacterial food grade coating inside drinking water tankin two coats with time interval of minimum 8 hrs.covering 7 years guaran tee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

Providing and laying telephone black /Amba White /Cadbury brown/ Rubyred/ Ocean Brown granite stone of 18 to 20 mm thick for door frame /dado /window boxing etc.On C.M.1:6 including filling joints with polymer base fill ernosing /moulding the sharp edges wherever necessary, curing, etc. complete.

Providing and fixing frame with / without ventilator of size as specified with Country cut teakwood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete

Providing and fixing factory made solid core flush door in single leaf 35 mm thick, decorative types,of exteri or grade,as per detailed drawings,conforming to I.S.:2202-1962 (Revised) with approved face veneers on both faces with /with out glazing and venetians in the positions shown on the drawings or as directed,all necessary beads,moulding and lipping,hold fasts,mat finishs tainless steel fixtures fastenings,finishing with french-polish /waxing complete. (with out door frame).(Sample to be got approved from Ex.Engineer before use) Commercial Hard Wood shutter

Providing and fixing fiber glass rein forced polyster door shutter 30 mm thick as per IS 14856 (2000) (Reaffirmed 2006) with out ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete.

Providing and fixing in position.(as per I.S.1868/1982) Aluminium sliding window of two tracks with rectangular pipe having over all dimension 63.50 x 38.10x 1.02 mm at weight 0.547 Kilogram /One Running Metre. and window frame bottom track section 61.85x31.75x1.20 mm at weight 0.695 Kilogram /One Running Metre. Top and side track section 61.85 x31.75x 1.30 mm at weight 0.659 Kilogram /One Running Metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram /One Running Metre.Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram /One Running Metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram /One Running Metre. and top section 40 x 18x 1.25 mm at weight 0.417 Kilogram /Running metre.As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc,complete.

Providing and fixing in position powde rcoated aluminium louvered windows /ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type,5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to10 mm thicknes sand confirming to IS.15622 -2006 (GroupBla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to10mm thickness and confirming to IS.15622 -2006 (GroupBla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

Providing and fixing European type white glazed earthenware coupled closet symphonic trap with symphonic low level white glazed 10 litres cistern with black backlite seat with all necessary pipe connection etc. complete.

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete.

Providing and fixing coloured glazed earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap brackets for fixing the cistern 32mm dia. P.V.C. flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap soil pipe connection up to the outside face of the wall

Providing and fixing white glazed earthen ware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.

Providing and fixing 450 mm x 550 mm size superior type Belgium mirror with 16 mm dia. nickel plated towel rod etc. complete.

Providing and fixing chromium plated towel rod 16 mm dia and 75cm. In length including all accessories complete.

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish

Providing and fixing on walls/ ceiling /floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stackingt he same in PWD chowky or as directed etc. Complete

Providing and fixing on walls/ ceiling /floor 25mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls /ceiling /floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing and fixing 15 mm dia. Screw down bib /stop tap of brass including necessary socket union nut complete.

Providing and fixing 25 mm dia. Screw down bib / stop tap of brass including necessary socket union nut complete.

Providing and fixing screw down 15 mm dia. Wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 25 mm dia. Wheeled stop tap of brass including necessary sockets /union nut complete.

Providing and fixing screw down for 50 mm dia. Wheeled stop tap of brass including necessary sockets/ union nut complete.

Providing and fixing push cock (Self closing tap) symet type of 15mm dia.including necessary socket, testing etc. complete.

Providing and fixing 50 mm dia meter water meter with non-return valve including strainer, sockets /union nut and including water meter box making locking arrangement and lock. [without chamber]

Providing andc onstructing Brick Masonry Inspection Chamber 90cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channel shalf round G.S.W. pipes, Brick Masonry, plastering from inside and air tight with 75 mm thick R.C.C. cover medium duty 140 Kilogram etc. complete.

Providing and laying for 225. mm dia salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing and fixing ISI1729/2002 grade 100mm dia Cast Iron Soil Pipes With lugs including plug bend necessary fittings such as bends, tees, single junction, double junction, slottedvent, off sets on wall orinto the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means of galvanised Mild Steel bracket of 30x5mm plate and 8mm square rod with Galvanised Iron clamp with wash erasper design, drawing and as directed to keep pipe 50mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of white oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer-in-Charge.

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete .

Providing and fixing P.V.C. Rain water pipes of 160 mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming toI.S.13592-1992 including proper rain water receiving recess with P.V.C. plug ,bend, necessary fittings ,suchas ,offsets,shoes,inluding fixing the pipe on wall lusing approved wooden cleats projecting 25 mm to 40 mm from face of wall a fixing with clips of approved quality and One Number filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. ormasonry blocks, including necessary scaf folding and maintenance for 3 yrs for any leakages or dislocations of pipes.All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing H.D. P container one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as in let,outlet over flow pipe inclusive of all tanks capacity between 1000 to 20000 liters

Providing and fixing 45 cm wide mild steel ladder of 40 mm x 6mm mild steel flat stringers and steps of 18 mm dia.mild steel bar for water tank including fixing it in(1:2:4)M-15 cement concrete block 60 cm x 30 cm x 30 cmand painting the ladder complete.

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter ( as per IRC 861983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Providing and constructing recharge pit of 2.0m deep and 1.0m dia of pre-cast RCC rings with 6.5" dia x 25m deep borewell at the floor of recharge pit including installation of combination of solid/perforated PVC casing pipe wrapped around with netlon mesh including 300mm thick sidefilling around outside of RCC rings (annular space) with 40mm size boulders including filling of recharge pit up to 0.5m depth with 25-75mm clean washed gravels from bottom up followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs, PVC end-caps, fittings etc. including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing.The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge.

Boring/drilling bore well of 300mm dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machinery required for the job, all complete as per direction of Engineer in charge, upto 90m depth below ground level.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well-casing pipe of 150mm dia, conforming to IS:12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per the direction of Engineer in charge.

Supplying, filling, spreading & leveling stone boulders of size range 5cm to 20cm in recharge pit, in the required thickness, for all leads & lifts, all complete as per the direction of Engineer- in-charge.

Supplying, filling, spreading & leveling gravels of size range 5mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge.

Supplying, filling, spreading & leveling coarse fine aggregate (crushed sand VSI grade finely washed etc.) of size range 1.5mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer in charge.

Providing and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish.

Providing and fixing in position UV resistant, fire retardant, virtually unbreakable and temperature resistant (-40° C to +130° C) Polycarbonate corrugated sheet of 2mm thickness for roof of approved make to match the roof profile at any height with G.I. J hooks bolts of G.I. clamps nuts & bolts or with self drilling fastener and EPDM washer etc. complete as directed

Providing and fixing 50mm diameter and 1.5 mm thick vertical and top Stainless steel hand railing in S.S.304 Grade with Stainless steel square / circular pipe bracing of size 32 mm x32mm x1.5 mm in 3 rows including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete

Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area greater than 0.9 One Square Meterr made out of 4 mm aluminum composite material of Class B mm aluminum sheet bonded with white retro reflective sheeting of Class __ ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on two no. mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm width including GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier

Providing and fixing kerbstone with led lighting system as per following specifications: dimensions with vertical mounting legs with 10mm horizontal square shape mild steel reinforcements. Illuminated kerb stone having visible dimensions :-500mm x 150mm x 150mm.(as per irc - 86-1983 ) 80mm legs having ms reinforcements shal be embedded in bt/concrete road surface.the kerb stone should have kerb angle of 45 degree, with rubber plugs at both ends of the kerbstones (2 nos)having load carrying capacity - vertical : 1465kg, horizontal : 2349 (certified by govt. Recoganized bodies)having thermal stability - : -40 to +120 degree celcius (certified by govt. Recoganized bodies. Illuminated kerb stones including : ingrace protection and connector rating ip67, electrical wire -(as per is: 694), led strip (as per lm:80) standard. Including for electrical fixing -frp junction box consisting of - 10amp. Switch module power supply(smps)having input voltage - 230v ac, output voltage 36v dc, 2 pole mcb. Illuminated kerb stones having warranty for 3 years. illuminated kerbstone shall be fixed into cast-in-situ cement concrete of m20 grade at base, back filling and grooves, including dismantling, fixing, removal of dismantled material and cleaning etc. Complete. The colour of kerb stone shall be provided as directed by engineer in charge.

Designing, Conceptualization & painting of 3D artistic on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Providing and fixing 90 cm x 60 cm Granite plate engraving 10 cm. height letter, figures including painting the lefters/figures with approved colour and shade complete

Providing and laying polished hand cut Kotah Stone flooring 25mm to 30mm thick and 45cm to 55cm wide in plain/diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete.Bd.M.3 Page No.380

Providing tuck pointing with cement mortar 1:3 for stone/Brick masonry including scaffolding and curing etc. complete. Bd. L. 16 PageOne Number 373

Providing and laying in-situ M30 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. MORT&H (5th Rev.) 1700, 2205, 2304

Providing and erecting Y type barbed wire fencing with seven rows of wire with 2.45 mm dia G.I. pipe ( Rezan/ concentiDeleted ire 0.75 mm dia ) with hot dip and G.I. coated hooks as per drawing supported on M.S. angle 50 x 50 x 6 mm at 2.5 mtr. c/c including fixing and fastening with wire, painting M.S. angles with one coat of red lead primer and two coat of oil paint etc. complete. As directed by Engineer in charge.

Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.As directed by Engineer in charge.

Providing weep holes in brick masonry /plain /reinforced concrete abutment, wing wall / return wall with 100mm diameter AC pipe extending through the full width of the structure with slope of 1V: 20H towards drawing face as per drawings and technical specifications etc. complete.

Prividing and fixing pressure relief pipes of 100 mm diametre of AC / PVC as per drawing for R.C.C Raft, galaries returns, abutments, wing wall etc complete. MORT&H (5th Rev.) 2705, 2706

Providing and fixing reinforced cement concrete cover of size 90 cm x 45 cm with frame over inspection chamber etc. complete. Heavy duty (225 kg)

Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/Square Metre) Spec. No.: As directed by Engineer-In-Charge.

Directional signage Design, supply, fabrication and fixing acrylic multilingual Braille (raised dots) directional signboards of size 6" x 9" designed as per accessibility standards and having 4mm thick acrylic base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8mm above base plate and the equivalent word written in Hindi with Devnagri non glare acrylic letters of height 15mm raised not less than 0.8mm above base plate and having a non glare acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per manufacturers specifications on the wall at the approved location and at a height of 1200mm from FFL and as per the directions by the engineer in charge. As directed by Engineer-in-charge

SS Dust Bin Two sides for extra strength during oscillating movement. Oscillating arrangement for easy unloading of Garbage. Area :0.765 Sqm , Capacity In Litres 42 Ltrs, Height : 0.92m

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Removing lime or lean cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc.

Dismantling stone masonry in Mud including stacking the materials as directed with all leads, lifts etc. complete.

Providing detailed layout plan of area in scale1:500 including carrying out contour survey and detailed Engineering plane table Survey with the help of 24 Alidade .The dolomite area measurement of the plot and structures ,trees ,overhead line and underground service amenities with in the area, with triangular method and giving detailes of the structures, such as total area, type of building and distance from all corners taking trial pit 0.5 x 0.5 x 2.00 m.-2 Nos. per acre and collection of record from city survey / D.I.L.R. authorities and authentication.The plan shall be traced on 75 micron polyster film and shall be submitted along with three Amoniaprints. The contour levels shall be marked at 0.5 Meter intervals.Note:-The items includes-1)Traversingworkwiththeodoliteandsteeltape .2)LevellingGridWorkoftheterrain. 3)DetailedEngineeringSurveyandcontouringworkoftheterrain. 4)Plottingwork. 5)CollectionofRecord. a)upto1Acre

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in superstructure including racking out joints when plastering is to be done / striking joints when no plastering is to be done on inside watering and scaffolding etc.complete

Supplying and laying laterite stone weighing 20 to 50 kilogram for Core / Sub armour layer including conveying with all the leads, lifts, laying in required lines, level, slope as per drawing including necessary equipments and machinery as directed by etc. complete in tidal conditions.

Providing and construction of a gabian structure for retaining earth with segments of wire crates of size 7.0 x 3.0 x 0.6m each divided into 1.5 m compartments by cross netting, made form 4 mm galvansed steel wire @ 32Kilogram per 10 One Square Metre having minimum tensile strength of 300Mpa conforming to IS:280 and galvanizing coating conforming to IS:4826 woven into mesh with double twist, mesh size not exceeding 100x100mm, filled with boulders with least dimension of 200mm, all loose ends to be tied with 4mm galvanized steel wire etc. complete

Providing and Constructing gabion structure 1 Meter high or required section made up of soft mechanically woven hexagonal shaped G.I. wire confirming to IS 16014:2012 having zinc plus PVC coating of overall diameter of 3.7 mm and tying lacing wire of 3.2 mm with edge wire confirming to overall diameter 4.4 mm edges being mechanically selvedge including placing in position, fitting neatly with trap stone rubble (15 to 23 cm) all loose ends to be securely tied (Excluding transportation) etc. complete.

Providing and laying Needle Punched and mechanically bonded non woven Geotextile of Type III indigenously manufactured from high quality Propylene staple fibers (continuous filament will not be accepted) on the prepared subgrade for Seperation.

Providing and fixing green marble of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges wherever necessary, curing, etc. complete.

Providing sand for kids play area with 20 kmtr lid.material rate

Providing and fixing RED Sand stone dry cladding upto 10 metre heights with 30 mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).

Providing and fixing White sand stone dry cladding upto 10 metre heights with 30 mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).

Providing and applying 2 coats of alluminiumpaintofapprovedmaketonewstructuralsteelworkinbuildingsandworkshopsincludingscaffoldingifnecessary,cleaningandpreparing the surface (excluding primer coat)etc. complete.

Providing and applying priming coat over new/old steel and other metal surfaces including preparing the surface by thorough lycleaning oil,grease,dirt and other for eignmat terands coured with wire brushes,fine steelwool,scrapper sand sand paper, scaffolding etc.complete.

Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge)

Providing and Fixing Decorative / Ornamental grills as per design for compound wall / Fencing including fabricating the grill using M.S. square / round bar, flats and angles including painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved colour and brand etc. complete as directed.

Providing and Fixing MS Safety grill of weight specified below for windows as per design including fabricating the grill using M.S. square / round bar, flats and angles including painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved colour and brand etc complete as directed. Grill weighing 25 to 30 kg / sqm

Providing, fabricating and fixing M.S. grill work as per approved design and as per weight specified below to fencing / compound mades out of square / round bars, M.S. flats, angles, with necessary holdfast including painting with one coat of red oxide zinc chromate primer and two coats of approved synthetic enamel paint etc. complete as directed by Engineer In Charge. Mild steel grill of weight 20 to 25 Kg/sq. m.

Providing, detailing, and fabricating as per specifications, transporting to site and erecting MS Openable / Sliding / Ornamental Entrance Gates including track and wheel, locking arrangement, fixing bolts, nuts, washers, cleats, stiffeners, gussets decorative balusters, arrow heads etc. and all necessary operations like straightening, bending, cutting, drilling, grinding, machining if specified, welding etc. complete weighing 60 to 65 kg/Sqm, including cleaning, Grinding and removing the welding burr and preparing surface and applying one coat of red oxide zinc chromate primer and one coat of Synthetic Enamel paint after fabrication and second coat of Synthetic Enamel paint after erection, with approved colour, shade and brand etc. including touching up with primer etc. complete as directed by Engineer In Charge

Providing and laying in position sandstone like asian stone with colour flooring of approved quality 25 to 30 mm thick in plain/diamond pattern on a bed of cement mortar 1:6 including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete as directed by Engineer-in-Charge

Providing and laying lacquer coated chequered tiles of approved quality of size 30 cm x 30 cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete

Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications & direction of Engineer-in-Charge. 60mm thick CC paver block of M-35 grade concrete with approved colour and design & pattern.

Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 Kilogram. to 20 Kilogram. Per Sq.m.) Spec.One Number: As directed by Engineer- in-charge

Providing and fixing 50 mm. dia. medium class G.I.pipe gate with wicket gate of approved drawing with all fixtures and fittings in two leaves with strong hold fast embedded in c.c. block at top and bottom with locking arrangement including cutting, bending, making holes and with one coat of primer etc. complete.

Providing structural steel work in hollow section of various thickness and sizes in square, rectanular and round shape from 25mm to 450mm section as per IS 4923 YST 310 Grade produced from iron ore and blast furnace route etc. as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/bolted/ welded connections and painting complete.

Stamp Concrete of 100mm Thickness-Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement,coarse and fine aggregate (natural sand /VSI grade finely washed crushed sand) Confirming to IS383,as per mixed in a batching and mixing plant/non tilting mixer and weigh batcher as per approved mix design,admixtures,transporting to site in nagpur city with lead up to 20 KM (on Inner Ring Road from Avastinagar to wadi),spreading, laying with approved make paver, compacted and finished in a continous operation, finishing to lines and grades Also Providing,Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @ 5kg per sqm. Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30%solids clear sealer @ 150 to 250gms per sqm using surface roller and protecting from falling dust,dirt and curring by curing compound /by providing cement vatain cement Mortor 1:8 @ 0.6 m x0.6 m center to center,admeas uring 80 mm at bottom and 40 mm at top with depth of 75 mm and maintaining the same through out curing period by anyother method approved by Engineer-in charge or Lands cape architect etc.complete.(prior approval of super inteding Engineer will be necessary )

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying two coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Removing old paint from steel and other metal surfaces and making the surfaces even with hand

Repair of steel railing to bring it to original shape cleaning and repainting as per drawing etc. complete

White washing two coats on parapet walls and white washing and geru lime painting to tree trunks including preparation of surface by cleaning scraping etc. complete

Cleaning of existing mural and removal of old paint of the existing mural followed by PU paint grade esdee paints or duco paints having application of 2 coats and final coat of clear PU paint matt or glossy finish, as directed by engineer in charge.etc. complete.

Providing and fixing stainless steel bollard of steel pipe 1.00 metre long of 250 mm inner diameter and circular top plate of 350 mm diameter with 5 mm thickness on deck of jetty in cement concrete including necessary fixtures and fastening etc. complete. (Stainless steel of grade S-304)

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm,...

Providing sculpture on wall including formation mould and fixing on wall completed.

Providing and Fixing Rubber flooring with 100mm p.c.c. & 100 mm soling.

Providing & Supplying & installation of Air walker of size 1100mm X 460 mm X 1480 mm of high quality steel 114mm and 3mm colour customized with 80-120 microns powder coated etc.complete.

Providing & Supplying & installation of Sit up board of size 1380mm X 660mm X 600mm high quality steel 114mm and 3mm colour customized with 80-120 microns powder coated etc.complete.

Providing & Supplying & installation of lat & pulley machine tube of thickness 2.5mm of size 1700mm X 855mm X 2150mm @ weight 210kg etc.complete

Providing & Supplying & installation of Angled leg press tube of thickness 2.5mm with dimension 217mm X 161mm X 126mm with weight 172kg. etc.complete.

Providing & Supplying & installation of Single seated & Push trainer of size 930mm X 700mmX 2100mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Providing & Supplying & installation of Double sit pedal equipment of size 1730mm X 450mm X 1450mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Providing & Supplying & installation of Commmercial treadmill of following specifications 1)motor:-6HP AC (3HP continues) 2) speed range 1-20kmph 3) Incline :- 0~20% 4) Display 6 Window, LCD Display, Speed, Distance, Lncline, Calories, Heart rate, Matrix running. 5) Heavy cushion for excellent kneecomfort 6) Hight speed circulation fan allow sweatproof workout 7) wheel for transportation 8) program : P1-P11 programs 9) running surface :62"X 22" 10) Maximum user weight : 160kg

Providing & Supplying & installation of Exercise Bike of size 970mmX 550mm X 1100mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Providing & Supplying & installation of leg extension & Leg curl tube thickness 2.5mm with dimension 1600mm X 1100mm X 1550mm with weight 215kg. etc.complete.

Providing & Supplying & installation of Parallel bars of dimension 2700mm X 560mm X 1400mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Providing & Supplying & installation of Double step walking machine of size 1550mm X 1220mm X 1450mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Providing & Supplying & installation of Horizontal Bar of size 1450mm X 90mm X 2360mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Providing & Supplying & installation of Teeter ladder of size 3000mm X 1100mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Providing & Supplying & installation of Wall Bar of size 1300mm X 120mm X 2300mm of high quality steel 114mm and 3mm colour cutomized powder coated 80-120mm microns etc.complete.

Gazebo-Providing, hoisting and fixing at all level precast or reinforced cement concrete gazebo with all elements like roofing, string courses, bands, copings, columns, pillars beams, plinth beams, railings, benches, flooring, foundations including architectural design, moulding, arches, shapes, and applying proper texture and painting coats to suit a particular asthetic elements(trunck of tree, shapes of animals, birds, timber benching any element or structure representing culture or tradition) the cost of required centering, shttering and reinforcement of 25 grade and fibrous material etc. complete as per the instructions of Architect or Engineer - in- Charge

Providing and fixing RCC Tree guard around trees.

Providing and fixing Stainless Steel LED Signboard, For Outdoor Lighting

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 80 mm thickness of having a strength of 300 Kilogram /Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete

Removing iron pipe raling having wooden R.C.C.or C.C.or iron post and stacking the materials as directed etc. complete

Scrapping the old plastered internal surface with sand paper and coating the entire surface with mixture of whiting or glue and linseed oil including scaffolding etc.complete as directed.

Removing the existing cement plaster of any thickness with out causing dustnuisance and stacking the debrisup to adistance of 50 metres or spreading in the compound and cleaning the site etc. complete.

Providing and fixing 20 to 25 mm thick rough shahabad box type water proofing for basement or underground floor on a base of Cement concrete 1:3:6,including subbase of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike water proofing liquids, raking of joints upto 35 mm depth, filling the joints with 6 mm size crushed metal,hand grouting with cement slurry,curing and cleaning, with 7 years guarantee on court fee stamp of Rs.100/-with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete )

Providing mobile kitchen BBQ vending trailer van fast food truck having size 4mt. X 2mt. X 2.30mt. with water system, material shall be galvanised sheet, aluminium steel etc, flooring shall be non slippery , work table shall be of stainless steel ,eletrical cabels shall be built in with lighting arrangement.

Providing and laying Rough Shahabad Stone Flooring 40 mm to 45 mm.thick and of required width in plain/diamond pattern on a bed of 1:6 C.M. including cement float,striking joints,pointing in cement mortar1:3curing and cleaning etc.complete

Fabrication, Supply & Installation of MS Portable Cabin on site as per the design drawing provided by the engineer of minimum height 11’ and made of following material Top Frame of 50mm X 50mm Specially Formed M.S Square Pipe, bottom frame of 125 mm X 75mm Specially formed M.S. I Beam , 5mm Thick Horizontal Cross Member :- 100mm X 50mm Specially formed M.S. I Beam, 5mm Thick Vertical Cross Member :- 50mm X 50mm Specially Formed M.S Square Pipe Bottom Frame should be painted with Black Japan Square Pipe as a stiffener for top, for side wall stiffener having 20 kind of material. Using 20mm X 40mm Specially Formed M.S panelling should be done in Specially Corrugated Sheet in Ms. – 1 mm X 40mm Specially Formed M.S Square Pipe, and side post having 65mm X 65mm Specially Formed M.S Square Pipe. Outside mm thick (18 guage). For internal wall panelling 8 mm PRELAMINATED BOARD SHEET. SHADE- HIGHLAND PINE with Bidding Patti and L-Patti in Black Coated Aluminium material should be used. (Internal partitions, toilet/bathrooms toilet fittings and transportation charges, electricity/diesel generator charges.) Detailed specification & drawing are available with the office of accessories to be paid separately) the rate is inclusive of Dy.Ch.E.(HIC).

Providing and fixing one set of 6 FRP Prefab bio toilet as per drawing and as per instructions of Engineer in charge

Providing and supplying musical Drums consisting of 3 to 5 drums and 3 fixing flat anchors – the best solution to install instruments on hard surfaces (e.g.concrete). Dimensions of all 3 including 80mm gap between drums – 910 x 300 x 690 mm Height ranges from 550mm to 850mm Tall.

Providing and supplying Tubular bells consisting set of tuned metal tubes of different lengths used as a musical instrument, suspended vertically from a frame and struck with a mallet to produce sounds or melodies. It includes total of seven tubes of sizes 2'-3' (set of 7)

Providing and supplying Aerophones - Tembos Pentatonic. A stylish support structure made of stainless steel pipes in a vertical orientation, with the tallest standing over 3m to the lowest around 1m of different sizes.

Providing and Supplying Bell Lyre is an outdoor instrument made of 8 graduated stainless-steel bells in a stand. The bells range in diameter from 100mm to 290mm

Providing and Supplying the Xylophone Duo.It is a distinctive instrument with an ergonomic curved design. Accessible from both sides.The Duo can be built with individual notes of aluminum or GRP of size 2m x 1m.

Providing and Supplying Harmony Bells made of four bells of decreasing size and ascending pitch.Available individually or in a 'bunch' of three bells in complementary chords.

Providing and Supplying Petal Drums sports a classic yellow center in the form of a babel drum, surrounded by white aluminum petals.Each ‘Petal Drum’ contains a small (10”/250mm) Babel Drum encased within specific shaped aluminum ‘petals.’ The flower heads are securely mounted to a stainless-steel frame or ready to be wall-mounted

PERGOLA - Providing and fixing M.S. pergola a structure built with columns or posts that support a series of rafters or latticework attached with 2 seater swings. Size: 2.5 x 0.75 x 3 M

Providing and fixing decorative M.S. pergola a structure built with columns or posts that support the rafters above pathway of size 3 x 1.5m and 3m height finished with desired wooden textured paint.

Providing and fixing decorative M.S. pergola above pathway of dof size 3 x 1.5m and 3m height topped with polycarbonate/acrylic sheets.

Providing and fixing FRP (Fibreglass reinforced plastic) cladding on the premade m.s framework or RCC structure base of thickness 25-50 mm with desired shape and designs.

Providing and fixing FRP (Fibreglass reinforced plastic) Murals on the given base wall of thickness ranging from 100mm to 300mm given a 3d effect of desired shapes and designs.

Providing and supplying FRP (Fibreglass reinforced plastic) Statue of different shapes and designs of size: L 6ft-8ft and height 5ft - 6ft.

Providing and fixing GRC (Glass reinforced concrete) cladding on the premade m.s framework or RCC structure base of thickness 25-50 mm with desired shape and designs.

Providing and fixing GRC (Glass reinforced concrete) Murals on the given base wall of thickness ranging from 100mm to 300mm given a 3d effect of desired shapes and designs.

Providing and fixing GRC (Glass reinforced concrete) Statue of different shapes and designs of size: L 6ft-8ft and height 5ft - 6ft.

Providing and fixing metal sculptures of given designs and forms of size L- 1 to 3m and H-1.5 to 2.5 m.

Providing and applying, Fixing Ferro cement cladding of reinforced concrete with thin walls that's made of cement mortar and closely spaced layers of wire mesh on existing M.S. framework with thickness of 20-25 mm.

Providing and fixing Rustic texture cladding made with aggregate material of sizes 8"x2.5" and thickness - 12 to 14 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

Providing and fixing Field stone handmade texture cladding made with aggregate material of sizes 120-390 x 50-220 mm and thickness - 22 to 35 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

Providing and fixing Field stone handmade texture cladding made with aggregate material of sizes 120-390 x 50-220 mm and thickness - 22 to 35 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone.

Providing and fixing River rock handmade texture cladding made with aggregate material of sizes 85-250 x 30-220 mm and thickness - 25 to 45 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

Providing and fixing Premium Ledgestone handmade texture cladding made with aggregate material of sizes 470x90, 275x90, 180x90 mm and thickness - 22 to 39 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

Providing and fixing Cimmerian handmade texture cladding made with aggregate material of sizes 400x95 mm and thickness - 18 to 22 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

Providing and fixing Travertine texture cladding made with aggregate material of sizes 11.8" x 2" and thickness - 18 to 20 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

Providing and fixing Rope Knit texture cladding of sizes 1480 x 580 mm and thickness - 3 to 5 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

Providing and fixing Wood texture cladding of sizes 900 x 150 mm and thickness - 3 to 5 mm mostly used in exterior. Density - 1700 kg/m3 Color options - Single tone / Multiple tone

PATHWAY - Providing and laying pavement stones of different sizes ranging from (1'x2', 2'x2', 2'x3') and loading the same on site.

Providing and laying of cobble stone of size 4"x4"x3" with 25mm thickness

Providing and laying Natural exterior pebbles stone of different sizes ranging from 10mm to 80mm with transport and loading

Providing and laying Natural exterior pebbles (Semi polished) stone of different sizes ranging from 10mm to 80mm with transport and loading

Providing and laying Sandstone Square Paving Stones, For Pavement of Thickness 20-30 mm and of mix sizes Colour : Beige, Brown, Grey, Red, White.

STONE SEATING - Providing and fixing stone seating including a set of 3 two seater benches of size 1.2 x 0.45 x 0.9 m along with centre table of size 0.45 x 0.45m finished with natural stone.

Providing and fixing Circular Stone seating set including 4 bench of 1 to 1.5m length and 0.45m wide and 1 centre table of size 0.5 dia x 0.5 m high. Total of 2-3m dia.

Providing and fixing a two seater stone bench of size 1.2 x 0.45 x 0.9 m made with approved white stone.

Providing and fixing of sandstone artifacts made with desired shape and designs of size 30"x11"x23" Colour - Mint Stone

Providing and fixing of sandstone artifacts made with desired shape and designs of sizes - H:36" & 15" Colour - Mint Stone

Providing and fixing of sandstone artifacts made with desired shape and designs of size 8"x10"x16" Colour - Teak Stone

SANDSTONE BENCHES - Providing and fixing of sandstone benches made with desired shape and designs of size 77"x16"x20" Colour - Teak Stone

Providing and fixing of sandstone benches made with desired shape and designs of size 71"x16"x20" Colour - Rainbow Stone

Providing and fixing of sandstone benches made with desired shape and designs of size 53"x18"x22" Colour - Pink Stone

Providing and fixing of sandstone bench made with desired shape and designs of size 70"x20"x22" Colour - Mint Stone

Providing and fixing of sandstone bench made with desired shape and designs of size 85"x17"x40" Colour - Rainbow Stone

Providing and fixing of sandstone bench made with desired shape and designs of size 59"x16"x16" Colour - Chocolate & Teak stone

SANDSTONE CARVING PANELS - Providing and fixing of sandstone carving panels made with desired shape and designs of size 20"x48" Colour - Mint Stone

SANDSTONE PLANTERS - Providing and fixing of sandstone planter pots made with desired shape and designs of sizes - H:13" D:24" Colour - Teak Stone

Providing and fixing of sandstone planter pots made with desired shape and designs of sizes - H:32" D:16" Colour - Mint Stone

Providing and fixing of sandstone planter pots made with desired shape and designs of sizes - H:30" D:23" Colour - Mint Stone

Providing and fixing of sandstone planter pots made with desired shape and designs of sizes - H:24" D:24" Colour - Teak Stone

Providing and fixing of sandstone planter pots made with desired shape and designs of sizes - H:16" D:22" Colour - Sagar Black Stone

Providing and fixing of sandstone planter pots made with desired shape and designs of sizes - H:30" D:18" Colour - Teak Stone

SANDSTONE LATTICE - Providing and fixing of sandstone lattices made with desired shape and designs of sizes - 42" x 36" Colour - Pink Stone

Providing and fixing of sandstone lattices made with desired shape and designs of sizes - 42" x 35" Colour - Red Stone

Providing and fixing of sandstone lattices made with desired shape and designs of sizes - 42" x 35" Colour - Pink Stone

Providing and fixing of sandstone lattices made with desired shape and designs of sizes - 42" x 35" Colour - Mint Stone

Providing and fixing of sandstone lattices made with desired shape and designs of sizes - 30" x 82" Colour - Mint Stone

SANDSTONE LAMPS - Providing and fixing of sandstone lamps made with desired shape and designs of sizes - H:36" D:19" Colour - Red Stone

Providing and fixing of sandstone lamps made with desired shape and designs of sizes - 11"x11"x23" Colour - Teak Stone

SANDSTONE PILLARS - Providing and fixing of sandstone pillars made with desired shape and designs of sizes - 19"x19"x83" D: 11" Colour - Pink Stone

Providing and fixing of sandstone pillars made with desired shape and designs of sizes - 12"x12"x82" D: 10" Colour - Teak Stone

Providing and fixing of sandstone pillars made with desired shape and designs of sizes - 10"x10"x82" D: 8" Colour - Teak Stone

Providing and fixing of sandstone pillars made with desired shape and designs of sizes - 12"x12"x69" D: 9" Colour - Pink Stone

Providing and fixing of sandstone pillars made with desired shape and designs of sizes - 16"x16"x84" D: 10" Colour - Teak Stone

Providing and fixing of sandstone pillars made with desired shape and designs of sizes - 14"x14"x82" D: 9" Colour - Teak Stone

Providing and fixing of sandstone pillars made with desired shape and designs of sizes - 14"x14"x82" D: 10" Colour - Teak Stone

Providing and fixing of sandstone Gazebo made with desired shape and designs of size - 96" x 96" Colour - Teak Stone wooden paint

SITC, erection and transportation of LED Signage of made in 4mm Arcylic male and female covers Lazercut and Moulded, each letter of size 15m x 1.5m x 0.2m. Source: LED Modules, Power :3Watt, Color: RGB, IP 65 with IP67 Meanwell driver. Cost includes the Stress to mount the signage. Cat.Ref: GLO-SIGN of make Lumen craft/Lightman/departmentalapproved make including cost of material and conveyance to work spot etc complete as directed by the departmental authorities.

Aviary - Providing and fixing Galvanized Iron Woven GI Wire Meshes made up of 0.6 cm spacing and 3.00 mm diameter wiring on the existing MS Sturctural Framework and finished with approved shade of powder coated paint. Area - 2500 sq.m

Providing and Fixing Topiary Garden Sculpture – Mural made in MS structure frame work covered in wire mesh from outside with vegetation on framework to get desired shape Height 2.5m x width 1.0-1.2m x thickness 0.75m

Providing and supplying, Fixing metal letter in SS 304 for name of the park at entrance. Each letter size approx 0.6(width) x 1.2m (height)x 0.15m (thickness)

Providing and fixing of seating for Play area in FRP (Fibreglass Reinforced Plastic) Umbrella - Size - 1.2m Dia x 3m height. To be made in FRP cladding on premade MS framework on RCC foundation to support MS structure. Stools - 0.45m Height x 0.4 m Radius

Gate in FRP 3M(length) X 2.7M(height). Thickness 0.45m dia Providing and fixing FRP (Fibreglass reinforced plastic) cladding on the premade m.s framework. Excavation for colum footing to be made till 750mm deep with rubble soling and PCC base of thickness 100 mm with footing of RCC.

Kid’s Play Area- Rubber flooring Providing and Applying Ethylene-propylene diene monomer (EPDM) is a durable and versatile M-class synthetic rubber poured in place on-site, providing a seamless surface of 8-10 mm thickness.

Providing and fixing metal frame structure, interconnected with metal supports to each other from top and anchored at bottom to be covered with ACP cladding & provision of outdoor LED lights inside. 10ft height & 10ft wide. To be provided at a distance of 0.75m centre to centre distance. Total - 12Nos.

FRP - Fibre Reinforced Plastic. Gazebo. Size - 8ft x 8ft. 12ft height. Providing and fixing FRP (Fibreglass reinforced plastic) cladding on the premade m.s framework or RCC structure base of thickness 100 m with desired shape and designs.

Mushroom Seat -out with table for children. 4 nos. Chair size - 1ft. Ht. Table size - Dia - 30" 1'6"ht. Make Providing and fixing FRP (Fibreglass reinforced plastic) cladding on the premade m.s framework or RCC structure base of thickness 100mm with desired shape and designs.

Mushroom House - 1 No.(size - 4ft x 8 ft) Providing and fixing FRP (Fibreglass reinforced plastic) cladding on the premade m.s framework or RCC structure base of thickness 100mm with desired shape and designs.

GRC - Glass Reinforced Concrete Roman columns to be provided and fixed of 12' height and 0.5m dia (as per design shared by architect)- total 20 nos.

Providing and Fixing FRP Gate design - along with name of the garden in ACP with light inside (2.5m - Width x 3m - Height x 0.3m depth )

Supply, Installation, Testing and commissioning of 3660mm height Pole made of circular mild steel pipe (grade YST 210) 88.9mm Dia x 2.9mm thick with 2178mm height. Decorative base made of Gravity Die-cast aluminium (245mm Dia x 206mm Height). The single arm bracket is a split constructed type, Bracket stem made of MS Pipe 60.3mm dia x 2.6mm thick, emerging from a Gravity Die cast Aluminium embellishment in gold or black finish of 60mm with a clear height of 1150mm crowned at top from the collar and with a cast Iron decorative finial of 260mm clear height. The artistically curved single arm made of MS Pipe 38.1mm Dia x 2mm thick, spruced up with MS Scroll with down sided leafy embellishment in gold or black finish, is firmly held to the stem by the way of cast iron clamp and the arm bears cast iron knobs at one end and other end facilitates the fitment of luminaire at 624mm from the vertical axis of the bracket stem. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500 mm from its base plate. The control gear tray is prewired with a single Core 2.5 Sq.mm PVC wire, 6A SP MCB of Approved make and with 32A stud type 4 way terminal block to take incoming wire with loop-in / loop-out arrangement and to be connected with lugs and has a 5 amp, 2way terminal connector for luminiare and a provision for earthing. Any other internal cables and connections shall be covered in the contractors scope. Mild steel mounting plate 230mm Dia x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at Pitch Center Distance 180mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication entire pole should be shot blasted (Inhouse). After shot blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Supply Installation testing and commissioning of Decorative Pole Technical Description :- 2955mm pole made of gravity die cast aluminium (LM6). Bottom Florus decorative element dimension details (245mm Dia x 206mm Height). Decorative base made of gravity die cast aluminium (340mm dia x 516mm Height). Decorative element (190mm dia x 550mm height) mounted on base and continuously tappered decorative flutted pipe made of gravity die cast aluminium (126mm Bottom Dia & 112mm Top Dia x 1000mm Height) fitted on decorative element with decorative die cast aluminium embellishment for mounting four arm bracket. Bracket stem made of MS square 120mm with decorative die cast aluminium embellishment of 375mm height with flower bud design on top 202mm. The four arm bracket made of gravity die cast aluminium extending from stem is spruced up with Leaf designer embellishment and facilitates the fitment of post top luminaire at 445mm on four side from the vertical axis of the bracket stem. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 200mm square x 12mm thick steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at CC 140. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension within +/- 5% tolerance. After fabrication, entire pole is shot blasted (Inhouse). After shot Blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options and Gold / Antique shade as special colour options.

Supply , Installation, Testing and commissioning of 3660mm height Pole made of circular mild steel pipe of two section (grade YST 210) Bottom section 139.7mm Dia x 3.6mm thick with 1000mm Height & Top section 76.1mm Dia x 2.6mm thick with 2648mm Height. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 110mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500 mm from its base plate.The control gear tray is prewired with single core 2.5 Sq.mm PVC wire, 6A SP MCB of Approved make and 32A stud type 4 way terminal block for loop-in / loop-out arrangement and to be connected with lugs and has a 5amp, 2 way terminal connector for luminiare and a provision for earthing. Mild steel mounting plate (Base Plate) 200mm Square x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at center to center 140mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication, entire pole is to be shot blasted (Inhouse). After shot blasting the pole is to be coated with Epoxy zinc rich phosphate primer and subsequently finished with pure polyester powder coating or using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Supply, Installation, Testing and commissioning of 4270mm height Pole made of circular mild steel pipe (grade YST 210) 88.9mm Dia x 2.9mm thick with 2788mm height. Decorative base made of Gravity Die-cast aluminium (245mm Dia x 206mm Height). The single arm bracket is a split constructed type, Bracket stem made of MS Pipe 60.3mm dia x 2.6mm thick, emerging from a Gravity Die cast Aluminium embellishment in gold or black finish of 60mm with a clear height of 1150mm crowned at top from the collar and with a cast Iron decorative finial of 260mm clear height. The artistically curved single arm made of MS Pipe 38.1mm Dia x 2mm thick, spruced up with MS Scroll with down sided leafy embellishment in gold or black finish, is firmly held to the stem by the way of cast iron clamp and the arm bears cast iron knobs at one end and other end facilitates the fitment of luminaire at 624mm from the vertical axis of the bracket stem. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500 mm from its base plate. The control gear tray is prewired with a single Core 2.5 Sq.mm PVC wire, 6A SP MCB of Approved make and with 32A stud type 4 way terminal block to take incoming wire with loop-in / loop-out arrangement and to be connected with lugs and has a 5 amp, 2way terminal connector for luminiare and a provision for earthing. Any other internal cables and connections shall be covered in the contractors scope. Mild steel mounting plate 230mm Dia x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at Pitch Center Distance 180mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication entire pole should be shot blasted (Inhouse). After shot blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Supply , Installation, Testing and commissioning of 3660mm height Pole made of circular mild steel pipe of two section (grade YST 210) Bottom section 139.7mm Dia x 3.6mm thick with 1000mm Height & Top section 76.1mm Dia x 2.6mm thick with 2648mm Height. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 110mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500 mm from its base plate.The control gear tray is prewired with single core 2.5 Sq.mm PVC wire, 6A SP MCB of Approved make and 32A stud type 4 way terminal block for loop-in / loop-out arrangement and to be connected with lugs and has a 5amp, 2 way terminal connector for luminiare and a provision for earthing. Mild steel mounting plate (Base Plate) 200mm Square x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at center to center 140mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication, entire pole is to be shot blasted (Inhouse). After shot blasting the pole is to be coated with Epoxy zinc rich phosphate primer and subsequently finished with pure polyester powder coating or using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative double bracket made out MS Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The Tentative shape is enclosed herewith .The final design shall be got approved from Engineer in charge.

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative Single bracket made out MS Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The Tentative shape is enclosed herewith .The final design shall be got approved from Engineer in charge.

Supplying & erecting Decorative light pole of height 3 m high (clear height) with double Arm decorative bracket made out GI Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from Engineer in charge.

Supply , Installation, Testing and commissioning of 3660mm height pole made of circular mild steel pipe (grade YST 210) 88.9mm Dia x 2.9mm thick with 2178mm Height. Decorative base made of Gravity Die-cast aluminium (245mm Dia x 206mm Height) in gold or black finish. The single arm bracket is a split constructed type, bracket stem made of MS Pipe 60.3mm Dia x 2.6mm thick, emerging from a Gravity Die cast mid section Aluminium embellishment in gold or black finish of 60mm with a clear height of 1150mm crowned at top from the collar and with a cast Iron decorative finial of 260mm clear height. The artistically curved single arm made of MS pipe 38.1mm Dia x 2mm thick, spruced up with MS Scroll with leafy embellishment at Center in gold or black finsh , is firmly held to the stem by way of cast iron clamps and the arm bears cast iron knobs at the one ends and other end facilitates the fitment of luminaire at 624mm from the vertical axis of the bracket stem. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500mm from its base plate. The control gear tray is prewired with single Core 2.5 Sq.mm PVC wire, 6A SP MCB of approved make and with 32A stud type 4 way terminal block to take incoming cables with loop-in / loop-out arrangement and to be connected with lugs and has a 5 amp, 2 way terminal connector for luminiare and a provision for earthing. Any other internal cables and connections shall be covered in the contractors scope. Mild steel mounting plate (Base Plate) 230mm Dia x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at Pitch Center Distance 180mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension and are within +/- 5% tolerance. After fabrication, entire pole should be shot blasted (Inhouse). After shot Blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Supply installation testing and commissioning of Tier drop Luminaire of 40/50W. Decorative pendant / Hanging mounted compact street light. Type IV (Asymmetrical light distribution). Decorative luminaire made of specially contoured spun aluminium body of high corrosion resistance with a neck design for unique and better aesthetics and non corrosive stainless steel fasteners. Clear polycarbonate diffuser. The luminaire have extruded aluminium heatsink for thermal management with vertical fin design for longerlife of the LEDs. The mounting arrangement nipple, coupling & Hex nut made of Stainless steel 304 suitablefor mounting to internally threaded pipe of designation M30. Protection class IP65. Mechanical resistance IK09 (Polycarbonate diffuser). Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K as per TMC Engineer and as per application. Colour rendering index (CRI)>70. Standard Deviation colour matching 3 MacAdam. Led module with expected service life of at least 72,000 operating hours. Driver shall be of approved make and are a Fixed constant current driver with an output current of 1200 MA, 48Vdc ,58W. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency > 85%, power factor > 0.95, THD < 10%, internal Surge Protection 6KV of the driver. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / Lumiled/ cree or Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 425mm diameter x height 407 mm / 437mm. BIS Certified for Luminaire.

Supply Installation testing and commissioning of 50W Post Top Luminaire Technical Description : Pole-top luminaire with Symmetrical light distribution. Luminaire made of spun aluminium, die cast aluminium and non corrosive stainless steel fasteners. Cast aluminium magudam attachment added for aesthetics. Prismatic diffuser. Suitable for mounting on Ø76 mm OD pipe. Pure polyester powder coated graphite grey & gold / anthracite grey & gold / jet black & gold. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 6KV. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 495mm diameter x 960mm height. BIS Certified for Luminaire.

Supply Installation testing and commissioning of 60W Post Top Luminaire Technical Description : Post top luminaire with Symmetrical light distribution. Luminaire made of spun aluminium, integrated with extruded aluminium pipe along with die cast aluminium base through supporting arms made fo gravity die cast aluminium and non corrosive stainless steel fasteners. Diffuser placed into the provision formed on the periphery of the bottom cover. Translucent UV stabilised acrylic diffuser. Die cast aluminium base suitable for mounting on Ø60mm OD pipe. Protection class IP65. Mechanical resistance IK07. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. SDCM-3 MacAdam.LED module with expected service life of at least 60,000 operating hours. Driver shall be K-lite/ Philips / Inventronics Driver is a Fixed constant current driver with an output current of 1050mA, 54Vdc ,58W. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 6KV. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 600mm diameter x 443mm height. BIS Certified for Luminaire.

Supply Installation testing and commissioning of 50W Post Top Luminaire Technical Description : Post top luminaire with Symmetrical light distribution. Luminaire made of gravity die cast aluminium top cover with decorative knob on top, gravity die cast aluminium housing integrated with decorative base leg and base. Die-cast aluminium base suitable for mounting Ø60mm OD pole. Translucent UV stabilised acrylic diffuser formed from non-yellowing acrylic sheet. All external screws are made of stainless steel. Protection class IP65. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 6KV. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 480mm length x 417mm width x 850mm height. BIS Certified for Luminaire.

Supply Installation testing and commissioning of 50W Post Top Luminaire Technical Description : Post top luminaire with TypeIII (Asymmetrical light distribution). Gravity die-cast aluminium top cover with gravity die-cast aluminium decorative knob on top, Gravity Die- cast aluminium supporting arm integrated with die-cast aluminium base suitable for mounting Ø50mm OD pipe. All external screws are made of stainless steel. Protection class IP65. Mechanical resistance IK09. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K, Colour rendering index (CRI)>70. LED module with expected service life of at least 72,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >88%, Power factor >0.95, THD <10%, Surge protection 6KV. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 325mm square x 545mm height. BIS Certified for Luminiare.

Supply Installation testing and commissioning of 50W Post Top Luminaire Technical Description : Post top luminaire with TypeIV (Asymmetrical light distribution). Luminaire made of specially contoured spun aluminium top cover with gravity die cast aluminium decorative knob on top. Clear acrylic / Clear polycarbonate diffuser. Gravity die cast aluminium supporting arm with base suitable for mounting Ø50mm OD pole. All external screws are made of stainless steel. Protection class IP65. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K, Colour rendering index (CRI)>70. LED module with expected service life of at least 72,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 6KV. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture.

Supplying and erecting LED Green Flood light fitting of 50W, including lamp, with PF > 0.95,class lP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No FGODF/FLS-2

Supply & Erecting IP 68 Neon Flexible Led Strip

LED Strip of 5W/mtr having IP67 protection and along with IP68 driver

Supplying and erecting LED square / circular Max. 18 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting integrated LED flood light fitting Max. 20W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 2000 Lumens, min. efficacy of 100 lumen/W, CRl>70, CCT upto 6500K, THD<10%, p.f.>0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70850, including driver with U shaped bracket with 5 Years warranty as per specification No FGODF/ FLS2.

Supplying and erecting integrated LED flood light fitting Max. 30W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 3000 Lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket with 3 Years warranty as per specification No FG-DF/FLS2

Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mA Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 Hrs with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20 % having useful life of minimum 25000 Hrs with over heat protection with minimum 2 years as per specification No. FG-IDF/LED

SlTC of high quality multicolor spot light, Power : 20W, Colour: RGB , Protection Rating : lP65, Beam Angle : 20°/45°, Body : Die casted, additional wall mount arrangements for fixing the lights. Optics: Specially designed to minimize hot spots & fringing in color mixing applications. Power lnput : DC 24V (without DC Driver) Make: Leksa Lighting/iGuzzini/Aultra Lighting/LaMartinie

SlTC of Power Driver for above lights, PO ER : 200W, lNPUT : AC 110-240V AC, 50HZ, OUTPUT : DC 24V, Protection rating lP66,Constant Voltage (C.V.) + Constant Current (C.C.) output, High efficiency up to 93%, orking temperature (case temperature)-45-+45°C, Protections: Short circuit / Over current / Over voltage / Over temperature, Comply with harmonic current limit per EN61000-3-2 Class C ( 50% load), Meet 4kV surge immunity level.

SlTC of 5 core DMX cable comprises twisted pairs with shield support for carrying of data. Featuring five/three pin connector support, these DMX- Cable options are suitable to be used with different type of fixtures. DMX512 cable is used for connecting all light consoles that use DMX 512 standard data transmission. Comprises pairs with a cross-section of 0.34 mm2 and general double screening.The external ultra-flexible sheath provides mobility of use and is very easy to coil.Make: FALCON/BELDEN/LL/GURUASTRONlCS

SITC Of RGB Controller (DMX) ,a port out put may be bring 2048 plus DMX pixels,it support off line control and play back content stored in the SD Card up to 64 GB support at least 50 different screen with digital display for changing modes, it supports master slave configuration to accommodate more DMX address(8 x512 pixels slave device)

Supplying and erecting Concealed type foot/step light Max. 5W having IP67, IK10 rated Pressure die cast housing having system lumens output of Min. 500 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, SDCM<5, p.f. >0.95, operating range of 230-270V, surge protection of 2.5 kV, Life class of 25,000 Hrs at L70B50, including driver by making necessary arrangement / recess in wall to make it flush with surface with minimum 2 Year warranty.

Supplying and erecting integrated LED Bollard Cylindrical / Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with minimum 2 Year warranty as per specification No FG-ODF/BL

Supplying and erecting LED Strip light 5m Length Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50,including driver with 1 year warranty.

Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL.

Providing & erecting 5 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Providing & erecting 4 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Supply and erection of Hot dip galvanized Ring for installation of mini high mast suitable for 4 Nos of LED Flood lights. The outer dia of ring shall be 600 mm. The ring shall be of 50 mm dia B class pipe with three supports to Sleeve, the sleeve shall be of 500 mm length and 4 mm thick duly provision of 4 nos bols and shall be suitable to fit on Octagonal pole of 70 mm AF

Supply and erecting of BREEZA TYPE decorative hot dip Glavanised single bracket of 0.5 meter long made from 48.3 mm OD pipe min 3mm thick with cap pipe length of 450 meter suitabal for OCT.pole with top of 70mm with 4 nos bolt .

Supply and erecting of BREEZA TYPE decorative hot dip Glavanised Double bracket of 0.5 meter long made from 48.3 mm OD pipe min 3mm thick with cap pipe length of 450 meter suitabal for OCT.pole with top of 70mm with 4 nos bolt .

Supply & errection of G.I. bracket for flood light fitting complete with bending,cutting,drilling & welding complete errected at position with necessary material duly PU painted

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 7 mtr long pole

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 6 mtr long pole

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 5 mtr long pole

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 4 mtr long pole

Supply and erection of BREEZA type decorative hot dip Galvanized single arm bracket of 1 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min3 mm thick with cap pipe length of 0.450 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or its equivalent as per the drawings enclosed.

Supply and erection of BREEZA type decorative hot dip Galvanized double arm bracket of 1 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min3 mm thick with cap pipe length of 0.450 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or its equivalent as per the drawings enclosed.

Providing PU paint as required of desired colour duly finished in an approved manner to BREEZA/MARVEL tyle decorative hot deep galvanized single bracket of 1 meter

Providing PU paint as required of desired colour duly finished in an approved manner to BREEZA/MARVEL tyle decorative hot deep galvanized double bracket of 1 meter

Providing PU paint / Powder coating as required of desired colour duly finished in an approved manner for 600 mm dia. Mini highmast ring

Supply Installation Testing & commissioning of integral high pressure Die cast/extruded aluminium LED Floodlight luminaire with proper heat dessipation & toughned glass protector or with yellowing injection molded polycarbonate cover having high light transmission index.The LEDs are provided with suitable lens for dispersal for achieving street light optics to ensure uniform light distribution.The LED fixture shall be desighned for at least L70 life of minimum 50,000 burning hours at ambient tempreture not less than 35*C. the system wattage (fixture's total power consumption) should be be 120W. Details as per technical specification attached.

Supplying and erecting LED Street Light fitting of 90 W, including lamp, with PF > 0.95 ,class IP 90 W and above Housing of pressure die cast alluminium alloy and heat sink extruded alluminium complete per specification

SITC of integral high pressure Die cast/extruded aluminium LED Streetlight luminaire 60W.

Supply of decorative luminaire made of spun aluminium body with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s is comprised of a deep drawn chemically polished and co-extruded, thermoformed polycarbonate protector stabilized agent UV rays suitable for 45W LED. Fitting should be post top mounting type decorative fixture. fitting should have decorative elements to be placed on top of the fixture for aesthetic purpose. Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KVA and external surge protection device of 10KVA, colour temperature 3000K / 4000K / 5700K Natural day light LED.LED's to be of Osram / Cree / Bridgelux & driver to be of make Philips / fulham / Osram.

Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mA Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 Hrs with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20 % having useful life of minimum 25000 Hrs with over heat protection with minimum 2 years as per specification No. FG-IDF/LED

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B 22/E-27 base as per specification no. FG-LP.

Supply installation testing and commissioning of Tier drop Luminaire of 70W. Decorative pendant / Hanging mounted compact street light. Type IV (Asymmetrical light distribution). Decorative luminaire made of specially contoured spun aluminium body of high corrosion resistance with a neck design for unique and better aesthetics and non corrosive stainless steel fasteners. Clear polycarbonate diffuser. The luminaire have extruded aluminium heatsink for thermal management with vertical fin design for longerlife of the LEDs. The mounting arrangement nipple, coupling & Hex nut made of Stainless steel 304 suitablefor mounting to internally threaded pipe of designation M30. Protection class IP65. Mechanical resistance IK09 (Polycarbonate diffuser). Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K as per TMC Engineer and as per application. Colour rendering index (CRI)>70. Standard Deviation colour matching 3 MacAdam. Led module with expected service life of at least 72,000 operating hours. Driver shall be of K-lite/ Philips/ Invetronics and are a Fixed constant current driver with an output current of 1200 MA, 48Vdc ,58W. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency > 85%, power factor > 0.95, THD < 10%, internal Surge Protection 6KV of the driver. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / Lumiled/ cree or Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 425mm diameter x height 407 mm / 437mm. BIS Certified for Luminaire.

Supply Installation Testing & commissioning of integral high pressure Die cast/extruded aluminium LED Floodlight luminaire with proper heat dessipation & toughned glass protector or with yellowing injection molded polycarbonate cover having high light transmission index.The LEDs are provided with suitable lens for dispersal for achieving street light optics to ensure uniform light distribution.The LED fixture shall be desighned for at least L70 life of minimum 50,000 burning hours at ambient tempreture not less than 35*C. the system wattage (fixture's total power consumption) should be be 150 W. Details as per technical specification attached.

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel,concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3m to 5m high octagonal /conical GI pole).

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel,concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Supplying and erecting pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. strip complete with all materials as per specification no. EA-EP

Supplying, erecting & marking SPMCB 0.5A to 5A in provided distribution board as per specification no. SW SWR/MC

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided onduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 3 core 4 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing M20 concrete for resurfacing the road.

Point wiring for light/fan/bell in 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification no. WG-PW/SW

Point wiring for independent plug in 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire,flush type switch, earthing and required accessories as per specification no. WG-PW/SW

Wiring for plug on board with flush Switch socket, copper wiring and earthing as per specification no. WG-PW/SW

Supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. FG-FN/CF

Supplying and erecting Energy Saving Ceiling fan of 3 star rating as per BEE 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification

Supplying & laying HMS PVC conduit 20mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification no. WG-MA/CC.

Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Supplying & fixing anchor type fastener fan hook, with 2 nos. of 10 mm dia x 75 mm long with necessary materials for ceiling fan.

Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Supplying and erecting PVC Surface modular double mounting plate 12 module complete duly erected

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation

Supplying and erecting decorative pre-wired box type fitting / batten suitable for 4 feet, T8 LED tube light (excluding tube light).

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core1.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB.

Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB.

Supplying, erecting, testing and commissioning self contained water cooler 230/250 Volts 50 cycles nominal cooling capacity of 150 litres per hour and storage capacity 150 litres with partially stainless steel body as per specification No. AP-WCR/WC

S/E ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200)

Supplying & erecting FRP box of size 300mm x 200mm x 125 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB

Supply,Erection,Testing and Commissioning of Garden speakerwith frequency response: 85 Hz to 20 KHz +/-5 db, sensitivity- 89 db//w/m power handling: 30w RMS, Impedance: 8 ohms, nominal.Drivers: glass filled Polycroplene basket 6.5" Polypropylene woofer, Polycone 1" Tweeter, weather handling: 38 degree C to 60 degree C, Body material: Lexan Polycorbonate Plastic, Coverage pattern: 360 degree Omni directional, similar to garden speak 50 of Ahuja Audio or its equivalents.

Supply,Erection,Testing and Commissioning of Professional Amlpifier Equivalents to SPA-15000 Ahuja make 1500 watts high power PA Amplifier.

Supplying and erecting Junction box for speaker

S & E Loud Speaker cable 4 Core 2.5 sqmm copper multistrand conductor shielded HiFi application cable conduit system

Supplying and erecting professional Ahuja fmx106dp with usb and bluetooth aux in mic in

Supplying & Erecting SS Rack Enclousure for music System

Supply and erection of GI bracket suitable for garden speaker.(U type bracket)

Dismantling the existing pole up to 6 m height with brackets, clamps,insulators, stay from the c.c. foundation and making the site clear by refilling the pits with excavated materials and bringing it to the ground level.

Dismantling the existing W.T. fluorescent fitting/ S.V./ M.V. / M.H. lamp /LED fitting from pole with brackets complete.

SITC streetlight Control Panel inclusive of all electrical accessories mentioned in tender document. With IoT based smart lighting system with 3 nos of CT for incoming side.

SITC of streeet light control panel inclusive of all electrical accessories mentioned in tender document

Supplying, installation, testing and commissioning of IP camera 4MP 1/3" CMOS image sensor full HD video resolution max 2688 x 1520, 20/30 fps True D/N IR Bullet / Box camera, 2.8-12 mm motorised lens, Auto Back Focus, High Light compensation, 120 dB and above True WDR, audio capture capability, 3 streams, ONVIF compliant, SD card Slot,with IP67 housing and mount with dehumidification feature with accessories such as mounting brackets/structures /fixtures etc. necessary to mount the camera on pole, etc. Smart codec H.264+ / H.265+, Certification from EU,UL & CE-EMC,FCC.

Supplying & erecting of High definition 4 Megapixel IP IR Dome / Bullet Camera with following features Image Sensor : minimum 1/2.8" / 1/3" Progressive Scan CMOS, Video Compression : H.264, H.265 or higher, at least Three individually configurable stream,Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, Lens Type : 2.8/4/6 mm Lens, fixed focal, Power Supply : Support 12VDC & PoE,IP67, Built in micro SD/SDHC/SDXC card slot of Built in microphone. Image Settings : brightness, contrast, sharpness, gain,white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Dig+D17ital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation.Events : Privacy Masking, Motion detection, Operating temperature ( -30 to 60° C ) . Security- User account and password protection, HTTPS, IP filter, Protocol - DHCP, UDP, HTTP, NTP, DNS, RTP, RTSP, SMTP, TCP/IP, UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable, CE, FCC certified.

SITC of Network video Recorder 16 Channe NVR Up to 12 M H265 NVR to support IP camera up to 6 MP,Hard disk,Power supply

SITC of Network video Recorder 8 Channel NVR Up to 12 M H265 NVR to support IP camera up to 6 MP,Hard disk,Power supply

Supplying, installation, testing and commissioning of 6000 GB Hard Disk for video Survelliance Equivalent

Supplying, installation, testing and commissioning of "32" TV Equivalent to : LG,Samsung

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x550x480 mm) as per specification no. WG-NAS/RAK

Supplying, fixing, and configuring 4 -ports unmanaged Din -Rail Industrial POE gigabit switch with 4 nos. 10/100/1000M POE Ports, 2 nos. 1000 Mbps SFP for uplink

Supplying, fixing, and configuring 8-ports 1 GE un-managed gigabit PoE switch compliant with IEEE 802.3 standards, min. 120W PoE capacity with 2GE SFP uplink erected in provided rack complet

SITC UPS - 600 VA at Junctions with 2 hrs back up to be housed with POE switch rack.

Supplying, erecting, testing and commissioning of single phase input & 1 phase output 1 kVA capacity online pure sine wave UPS, with backup time of .......hrs. PWM & IGBT based, with 0.8 to unity output pf complete with all protections

Supplying and installing FR PVC sheathed Aluminum foiled wrapped over all tinned copper braided HDPE insulated copper cat-6 STP cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

Supplying, erecting & terminating XLPE armoured cable 2 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe

Power supply kiosk of size of 400 mm x 400 mm slanted made from 14 swg powder qouted GI sheet duly equipped with lock & key and magnet lock supported on GI pipe of min 100 mm dia & suitable height and complete with earthing stud necessary foundation and pipe type earthing as per drawing enclosed. Job includes erection of provided MSEDCL energy meter

Supplying and installing PBT loose tube HDPE sheathed armoured single mode optical fiber cable with 6 fiber, core dia 9/125μm (OS1/OS2) 10 GBPS speed compliant to IEC 60793/IEC 60794 standards in provided

Supplying, erecting & marking DPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting cantilevers of suitable size mounted on pole for holding cameras for veiwing. Complete as directed by engineer - in-charge

Supply & erection 12.5 H.P.vertical monoblock submercible oil filled pump set,with 2 ball bearings,suction defuser for high discharge with ceramic mechanical seal ISI mark discharge 900 LPM at 30 mtr. Head & delivery size of 75 mm dia.

Supplying and erecting fully Automatic star/delta starter suitable for 12.5 H.P. to 15 H.P. for 3 phase squirrel cage motor totally enclosed with overload and no volt relay complete erected on provided angle iron frame.

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SWSWR/MCB

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6A to 32A, C- series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting fuse bridges with base HC type fuse links 415V, 100A erected on polished wooden block.

Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

Supplying and erecting Galvanised cast iron earth plate size 60 x 60 x 0.6 cms. complete with all materials, testing & recording the results as per specification no. EA-EP

Providing & fixing LED underwater light fittings IP 68 suitable above 18 watts to 27 watts in pressure dia cast aluminum alloy housing and heat sink extruded with changing colours and surge protection device complete with specific colour

Providing & fixing electronic driver for synchronized automatic light changing in red, green & blue colours for LED lights with logical controller for various changing patterns and remote control with surge protection device, short circuit & open circuit protection up to 650 watts

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting ISI mark G.I.pipe 50mm dia C’ class at position with accessories as per specification no.CW-PLB/GP

GI pipe ring of 50mm dia Sleamless G.I.pipe "C" class with cutting bending, drilling, tapping and brazing of nozzle base complete 5 mtr. Dia.

GI pipe ring of 50mm dia Sleamless G.I.pipe "C" class with cutting bending, drilling, tapping and brazing of nozzle base complete 4 mtr. Dia.

GI pipe ring of 50mm dia Sleamless G.I.pipe "C" class with cutting bending, drilling, tapping and brazing of nozzle base complete 3 mtr. Dia.

Supplying and erecting 50 mm dia. gun metal sluice valve at position with necessary materials complete.

Supply & Erecting central nozzle 25 mm dia brass flexible 190 mm height

Providing and fixing 80 mm & 10 mm dia jet type nozzle brass flexible with ball joint.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, platform etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by

Supplying, erecting & terminating XPLE armoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/A

Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 3 core 6 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supply & erecting Stainless steel wire mesh 2 mm for suction filter.

Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

SITC of pole mounted type Outdoor junction Box along with pole mounting accessories, and for equipment mounting suitable for accomodating ,Electrical switch unit, UPS, Media Converter and POE switch, as directed by Engineer In Charge.

Supplying and erecting ISI mark G.I. pipe pole ‘B’ grade 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. OH-PL/GIP

Making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal,(45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered,with necessary curing and finishing complete. (for 6 m pole)

Second year Comprehensive Maintenance of all electrical Works (2.5% of estimate cost)

Third year Comprehensive Maintenance of all electrical Works (4% of estimate cost)

Fourth year Comprehensive Maintenance of all electrical Works (5.5 % of estimate cost)

Excavation: Excavation for foundation in earth, soil of all types,sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift up to 0.00 to 1.50 m.) By Manual Means. Rate= Rs.239/Cu.Mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra 2022-23 PageNo 07 2. LABOUR Sr No.1)

GARDEN SOIL:- Supplying on site garden soil well sieved 80 % to pass through I.S. sieve of 10 mm size free fromstones rubbish like dried grass roots and other such materials.The soil should be fresh from quarry. The color of the soil generally is red. The soil will be measured by measuring box.(Farma) Item includes Transporting, loading unloading etc (.Lead charges per 70 km. considered Excluding royalty.) Rate= Rs.1500/ Cu.Mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23 Items of garden work, Page No 8 /3.Material Charges Sr No.1)

FARM YARD MANURE: - Supplying on site well decayed,well dried, well powdered, without clods and free from stones, dried grass and other rubbish material. The color of themanure generally is black. The manure will be measured by measuring box. (Farma)Item includes Transporting, loading -unloading etc (.Lead charges per 50 km. considered.) Rate= Rs.1550/Cu.mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra 2022-23 Page No 8 / 3. Material Charges Sr No.1)

Excavation for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed in earth, soil of all types, soft murum, including removing the excavated material up to a distance of 50 mtrs. for a depth of 30 cms. Rate= Rs.71.70/Sq.mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra 2022-23 Page No 11 Sr No.3)

Supplying on site fresh Garden soil (free from stones rubbish like dried grass roots, other such materials) for excavation area of depth of 30 cms. ( consolidated thickness). Rate= Rs.391.50 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23 Items of garden work, Page No 13 Sr No.36a)

Supplying on site well decomposed Farmyard Manure for excavation area of depth of 30 cms. (Consolidated thickness). Rate= Rs.125.55/Sq.mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra 2022-23 Page No 13Sr No.36b)

Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting reqired plant species, lawn grass as directed etc. complete for required depth 30 cms. for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed/ ground cover. (1/10 of semiskilled labour) Rate= Rs.77.76/Sq.mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR ,2022-23 Page No 12 Sr No.23)

Filling fresh garden soil / silt & manure in excavated area of depth 30cms. Add-Increased in percent for Corporation Areas @ 5% Rate= Rs.27.02 (As per Parks and garden, PWD Government of maharasthra DSR 2022-23 Sr No.13)

Providing on site well established (free from weeds /disease etc.) ready to fix lawn turf in slabs/ rolls of required variety as directed. Rate= Rs.215.00/Sq.mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Sr No.47)

Tagar variegated (Bag Size 10"x 10, hight of plant 30 cm to 60 cm ) Rate - Rs. 48 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 ,1 (b)Flowering Shrubs item No 25)

Hibiscus Well Developed, Healthy Foliage / Half Bloom Stage , Free from Pest and Diseases. (Bag Size 8" x 11"", hight of plant 20 cm to 45 cm) Rate - Rs. 68/Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges item No 7)

Ixora singaporensis Well Developed, Healthy Foliage / Half Bloom Stage , Free from Pest and Diseases. (Bag Size 8" x 10"", hight of plant 30 cm to 60 cm) Rate - Rs. 95/Sq.mtr Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges item No 3)

Malphigia (Bag Size 10''x 10", hight of plant 45 cm to 60, cm) Rate - Rs. 45/Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 20 , 1 (b)Flowering Shrubs item No 20)

Hamilia (Bag Size 8" x 10", hight of plant 20 cm to 45cm) Rate - Rs. 48/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges item No 6)

Allamanda (Bag Size 10" x 10", hight of plant 15 cm to 30 cm) Rate - Rs. 55/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 16 , 1 (b)Flowering Shrubs item No 2)

Canna Dwarf (Bag Size 7" x 8", hight of plant 30 cm to 40 cm) Rate - Rs. 20/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 21 , 4 Bulbous/Rhizomatous plants item No 3)

Heliconia any type (Bag Size 18 '' x 18 '', hight of plant 60 cm to 75 cm) Rate - Rs. 70/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 18 , 1 (b)Flowering Shrubs item No 28)

Mayurpankhi/Thuja (Bag Size 13" x 13", height of plant 45 cm to 60 cm) Rate - Rs. 206/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 16 , 1 (b)Flowering Shrubs item No 03)

Jatropha (Bag Size 8"x 10", height of plant 45 cm to 60 cm) Rate - Rs. 40/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 12)

Eranthemum (Bag Size 8"x 10", height of plant 20 cm to 45 cm) Rate - Rs. 48/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges item No 05)

Duranta golden (Bag Size 8" x 10", hight of plant 30 cm to 50 cm) Rate - Rs. 42/Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges item No 03)

Ratrani/Night queen (Bag Size 8" x 10" , hight of plant 45 cm to 60 cm) Rate - Rs. 55/Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 19)

Murraya/ Kamini (Bag Size 9"x11" , hight of plant 20 cm to 45 cm) Rate - Rs. 55/Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 19)

Sadafuli/Vinca (Bag Size 6"x 7" height of plant 10 cm above) Rate - Rs.22/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 32, 9 (B) Hybrid Flowering Seasonal in bags, item No 32)

Bouganvillae Glabra (Bag Size 8" x 10" height of plant 30 cm to 50 cm) Rate - Rs. 95 / Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges, item No 11)

Acalypha (Bag Size 8" x 10" height of plant 40 cm to 50 cm) Rate - Rs. 35 / Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges, item No 01)

Ixora Duffy pink (Bag Size 8" x 10", hight of plant 25 cm to 40 cm) Rate - Rs. 70/Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 09)

Rangoon creeper/ Madhu malati (Combretumindicum (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 35 / Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Tulas (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 15 / Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Alovera (Korphad) (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 20 / Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Mint (Pudina) (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 15/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Stevia (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 28/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Lemon Grass (Gavti Chaha) (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 28/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Ashwagandha (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 35/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Akkalkara (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 28/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Betal Vine (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 35/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Gulvel (Giloe) (Bag Size 7" x 8", height of plant 15 cm to 30 cm) Rate - Rs. 35/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 16)

Areca Palm (Bag Size 10"x 12" height of plant 3 to 4 feet) Rate - Rs.140/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 32, 9 (B) Hybrid Flowering Seasonal in bags, item No 32)

Aralia (Bag Size 13" x 13", height of plant 30 cm to 60 cm) Rate - Rs. 95 / Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 19 , 2 (b) Foliage Shrubs item No 03)

Schefflera green (Bag Size 13" x 13", height of plant 40 cm to 60 cm) Rate - Rs.110 / Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 20 , 2 (b) Foliage Shrubs item No 21)

Pisonia alba (Bag Size 10"x 10" height of plant 30 cm to 45 cm) Rate - Rs.206/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 20, 2 (b) Foliage Shrubs, item No 22)

Croton (Bag Size 13"x 13" height of plant 30 cm to 60 cm) Rate - Rs.165/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 20, 2 (b) Foliage Shrubs, item No 6)

DracaenaGolden (Pot Size 6" height of plant 20 cm to 30 cm) Rate - Rs.110/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 11, 10 (a) Indoor Plants in pots, item No 33)

Cordyline (Bag Size10" x 10", hight of plant 30 cm to 45 cm) Rate - Rs. 40/Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 18 , 2 (a) Foliage Shrubs item No 05)

Miniature diff. var. (Bag Size 10"x 12" height of plant 30 cm to 45 cm ) Rate - Rs.205/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 37, 13 (b) Roses , item No 04)

Climbing diff. var. (Bag Size 10"x 12" height of plant 30 cm to 45 cm ) Rate - Rs.274/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 37, 13 (b) Roses , item No 05)

14'' Round Shape Plastic Pots (Sanction Quotation Rate)

Premium outdoor Topiary Hight 5 to 6 feet (Sanction Quotation Rate) Species, Shape, Height & Quality as per directions from Garden Superintendent/incharge

Hanging Pots (Sanction Quotation Rate)

Pilea (Bag Size 5"x 6" height of plant 10 cm to 20 cm ) Rate - Rs.12/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 28, 8 Ground Covers , item No 08)

Porthulaca (Bag Size 5"x 6" height of plant 10 cm to 20 cm ) Rate - Rs.20/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 29, 8 Ground Covers , item No 09)

Zebrina pendula (Bag Size 5"x 6" height of plant 10 cm to 20 cm ) Rate - Rs.15/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 29, 8 Ground Covers , item No 12)

Coco peat Good quality washed having low e.c. (electrical conductivity) good water retention capacity, free from unwanted rubbish material. Rate - Rs.12/ kg Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 09, Other Material , item No 02)

Vermicompost: - Good quality well decomposed black colored, odourless pest and disease free, with appropriate nutrient and moisture content free from unwanted rubbish material. Rate - Rs.10/ kg Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 09, Other Material , item No 01)

Neem oil (Sanction Quotation Rate)

Chrysanthemum (Bag Size 7"x 8" height of plant 30 cm to 45 cm ) Rate - Rs.35/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 22, 4 Bulbous/Rhizomatous plants , item No 10)

Coleus (Bag Size 5"x 6" height of plant 10 cm to 20 cm ) Rate - Rs.12/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 28, 8 Ground Covers, item No 5)

Gerbera (Bag Size 7"x 8" height of plant 15 cm to 20 cm ) Rate - Rs.28/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 28, 8 Ground Covers, item No 7)

Petunia (Bag Size 7"x 8" height of plant 10 cm and above ) Rate - Rs.24/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 32, 9 (B) Hybrid Flowering Seasonal in bags , item No 23)

Marigold African (Bag Size 6"x 7" height of plant 10 cm and above ) Rate - Rs.22/ Nos Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 32, 9 (B) Hybrid Flowering Seasonal in bags , item No 20)

Providing Garden Soil Description Supplying on site Garden Soil well sieved @ Rs.1575/- per m3 (Ref. Schedule Rate for Parks & Gardens 2022-23 Pg.No.8 It.No.1.)

Providing Farm Yard Manure Description Supplying on site well decayed dried FYM @ Rs.1627.50/- per m3 (Ref. Schedule Rate for Parks & Gardens 2022-23 Pg.No.8 It.No.2)

Unskilled Heavy Labour Supply on site unskilled labour @ Rs.442.31/- per day for Garden Work through the year. Ref – Labour Commissioner, Minimum Wages Act Rate 442.31/- per Day plus 46% Leavy

Unskilled Heavy Labour (Mali Work) Supply on site unskilled labour @ Rs.442.31/- per day for Garden Work through the year. Ref – Labour Commissioner, Minimum Wages Act Rate 442.31/- per Day plus 46% Leavy

Supply of Rubble Stone blasted Rubble stone excluding royalty PWD/DSR/General Rates/It. No.15 Pg No. 541

Supply of Brick Bats : PWD/DSR/It. No.BdJ - 02 Pg No.525

Unskilled Heavy Labour. (PWD SSR 2022-23 Page no.-545/ Sr. No. -36)

Dumper Ref- Hon Standing Resolution No 161 dt- 17/05/2021

Multi Seater See-Saw

Toddler Swing

S Bridge Ladder Scramber

Bridge Ladder

Spring Rider Pony

Spring Rider Orca

Animal MGR

Double Arc Swing

Spring Rider Jumbo

FOUR SEATER MGR

Twindler Go Round

Hiravati Enterprises