PROVISION OF FURNITURE STORAGE ACCOMMODATION FOR BSO UNDER GE DAMAN AT ICGAS DAMAN

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out soft/loose soil

Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D-2, using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified.

M&L for formwork to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished square, rectangular or polygonal surfaces of concrete complete all as specified and directed

M&L for formwork to faces of sides and soffits of floor or roof beams, cantilevers, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed

M&L for flat formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

M&L for reinforced cement concrete (1:2:4) type B1 (nominal mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc; basement slabs under reamed pillars and mass concrete complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

M&L for reinforced cement concrete (1:2:4) type B1 (nominal mix) using 20 mm graded stone aggregate as in column, pillars, piers, post and struts complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

M&L for reinforced cement concrete (1:2:4) type B1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

M&L for reinforced cement concrete (1:2:4) type B1 (nominal mix) using 20 mm graded stone aggregate as in slab supported on wall for storage rack, completed all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

TMT bars 8 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for factory made precast cement concrete block masonry (1:3:6) type C1 using 20 mm graded stone aggt with solid blocks, exc10 cm in width, set in cement morter (1:6) in wall complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance exceeding 1.5KM but not exceeding 5 KM and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

M&L for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface.

M&L for Walling of random rubble uncoursed, well bonded bedded and solidly hearted built in CM 1:6 (below ground level) complete all as specified as directed.

M&L for 150mm thick PCC 1:3:6 type C2 40mm graded aggregate as in flooring, finish cement concrete surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 100mm thick PCC 1:3:6 type C2 40mm graded aggregate as in flooring, finish cement concrete surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 40mm graded aggregate as in plinth protection/paving/footpath, flooring, complete all as specified and directed.

S&F glass dividing strips, 3 mm thick and 38 mm width, complete all as specified and directed.

M&L for Screed bed or bedding layer of mortar 20 mm thick in Cement Plaster (1:4) for laying floor finishes, completed all as specified and directed.

M&L for rendering 10mm thick in Cement Mortar (1:3) on fair faces of brick work or concrete surface (used as screed bed for tiles in vertical surface), completed all as specified and directed.

M&L for Non - skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors or in veritcal surface for dedo or skirting etc. set and jointed in neat cement slurry and pointed in coloured cement to match, Complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastening (Beam, tee, angle, channel or flat sections) icluding distance pieces, cleats etc, complete all as specified & directed.

S&F for mild steel bolts not exc. 12mm dia of neck, purpose made with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed with to be fitted with washer and one hexagonal or square nut exc. 30 cm long, complete all as specified and directed.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply, and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall hickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S.galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineerin- charge.

Supply only 5.50 mm thick float glass (area of each pane exc 0.50 sqm) fixed in aluminium sliding window/door shutters etc complete all sas specified and directed.

S&F for Solar controlled film 50 micron reflective type sticked to glass as per instructions of manufacturers all specified and directed.

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of mild steel heavy duty and fixed.complete all as specified and directed.

S&F for mortice lock vertical type of brass of size 100mm 4 lever fixed to aluminium door with complete fittings etc complete all as specified and directed

S&F for Butt hinges, medium weight 125MM Size, cold rolled mild steel, and fixed to chowkhat and door, complete all as specified and directed.

S&F for 200mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed.

S&F for 250mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed.

S&F for 150mm size extruded brass handles fabricated type, polished etc complete all as specified and directed

S&F for floor door stopper of brass body and tongue with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm.

M&L for rendering 10 mm thick plaster on other than fair faces of brick/concrete surfaces in CM (1:6) on wall surface, finished even and smooth without using extra cement.

M&L for rendering 15 mm thick plaster on fair faces of brick/concrete surfaces in CM (1:4) on wall surface, finished even and smooth without using extra cement.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading/eave gutter to wall/iron purline, fixed with self tapping screws or welding as specified.

S&F for hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, blusters, nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire etc including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 , completed all as specified and directed.

S&F for 110mm bore dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specidied and as directed

M&L for prepration of new steel surfaces of any description, exceeding 10cm in width or girth, and applying two coat of synthetic enemel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

M&L for Anti-termite treatment treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area, complete all as specidied and as directed.

M&L for Anti-termite treatment treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured), complete all as specidied and as directed.

M&L for Anti-termite treatment treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specidied and as directed.

M&L for Anti-termite treatment treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specidied and as directed.

M&L for Anti-termite treatment treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specidied and as directed.

M&L for preparation on new plastered surface of wall, chajja, parapet etc and applying two coats of acrylic emulsion paint (two or more coat applied @ 1.67 ltr/10 sqm over including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including 1.5mm thick wall care putty complete all as specidied and as directed

M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper paint on walls over a coat of alkali resistant primer includng 3mm thick wall care putty etc complete all as specified and as directed .

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

One light point / fan point controlled by one switch.

One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5sq. mm size

Supply & fixing modular type switch 6 Amps ,1way,1 module.

Supply & fixing modular type switch 16 Amps ,1way,1 module .

Supply & fixing modular type socket 6 Amps, 2/3 Pin combined 2 module .

Supply & fixing modular type socket 6 A/16 Amps, 6 Pin combined 2 module.

Supply & fix ceiling rose, 3 terminal ,PVC/polycarbonate body

Supply &fix modular type fan regulator stepped type 120 W- 2 module.

Supply and fixing LED lights fitting 1x 22W, 220V, 4' long AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix, factory made, MCB DB's, 8 way 415 volts, AC,TPN, vertical distribution board, 4 way, painted with epoxy based powder coated suitable for m

ounting MCB as incomer of FP and MCB SP /TP as outgoings and complete with and including 200 amps rated copper busbar, neutral bar,earth bar, connecting cable links with and including top and bottom removable gland plate, complete with IP 43 protection, all as specified and as directed.

S&F of sheet metal enclosure MCB SPN DB 8 Way type 240 volts Double Door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed by Engineer in charge

Supply and fix for MCB FP 63 Amp 10 KA "c" series complete all as specified and directed.

Supply and fix for MCB DP 40 Amp 10 KA "c" series complete all as specified and directed.

Supply & fix for MCB SP 6 to 32 Amps 10 KA,"C" series complete all as specified and directed.

Material and labour for submain wiring along with earth wire using 2 X 4.0 sq mm(colour coading) + 1X4 sq mm earth wire(green colour) of single core PVC insulated multistranded copper conductor 1100 Volts grade FRLSH type in and including PVC conduit medium grade not less than 25 mm dia with all conduit accessories concealed in wall/ceiling/beams/column etc. complete all as specified

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380m sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fixing LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core

All as per item No.1 above, but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm complete all as specified and directed for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switch on independent board.

Addition & Alteration by cutting , welding and fabrication etc for making space for fixing of MCCB into existing feeder pillar box and supply and fixing 1 No MCCB 4 pole, 63 Amps, 415 volts ICU of 27 KA with microprocessor release and adjustable overload 70 % to 100 % including making incoming and outgoing electrical connections , making good to panel surface by painting with existing colour paint complete all as specified and directed.

Cutting of existing road, concrete/ bituminous surface by using of mechanical method of any type complete all as specified and directed Note:-PCC for making good road surfaces shall be measured and paid separately)

Material and labour for PCC (1:3:6) type C2 using(40 mm graded stone aggregate ) for making good distrubed road surfaces including necessary use and waste of form work complete all as specified and directed

Supply and laying GI tube light grade Galvanised with , laid in trenches Bore of Pipe 80 mm Complete all as specified and directed.

Supply and lay new high density polyethylene DWC pipes of 63mm OD/ 50mm ID, 6 kgf/sqcm including all fittings (bends, Tees, Elbows, sockets, etc) as required on site, complete all as specified and directed. Note:Excavation, return filling and removal of any type of soil/ strata shall be measured and paid separately under respective items of BOQ.

Excavation in trenches , not exceeding 1.5 mtr wide and not exc 1.5 mtr depth for laying of cables, pipe lines, protection pipes and foundations etc and getting out in any type of loose soil complete all as specified and directed.

Returning filling in soil including spreading leveling watering and well rammimg in layer n exc 25 cm complete all as specified and directed

Removing excavated soil not exc 50 mtr ant depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed