SPECIAL REPAIR TO BLDG NO. T-63, T-64, T-81, T-84 AND T-248 ALONGWITH MISC SANCTIONED MINOR WORKS AT TANGTSE AREA UNDER GE 860 EWS

Amount

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs blankets any thickness, including cover fillets complete all as specified and directed by Engr-in Charge.

M & L for Veneered decorative plywood, 4 mm thick 3 Nos of ply grade 1 (with BWR resin) with decorative face veneers on one face fixed with nail to timber frame work as in ceiling complete all as specified and as directed.

M&L for 9mm Pre-laminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws/nails to timber frame work in wall portion complete all as specified and directed.

Dismantling of timber fillets, rails, posts, rafters, purlins, etc. sectional area n.exc. 40 sq. cm in frame work complete all as specified and directed by Engr-in Charge.

M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 13 Sq cm n.exc 25 Sq cm secured with nails or brads complete all as specified and directed by Engr-in Charge.

M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 3 Sq cm n.exc 6 Sq cm complete all as specified and directed by Engr-in Charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in Charge.

Description all as per item No. 8.00 here in before but plain steel sheet complete all specified and as directed by the Engineer-in-Charge.

S & F 0.50mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and as directed.

S & F 0.50 mm Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with L type of J type or cranked hook bolts in lieu of screws all as specified and as directed.

M&L for preparing of new steel surfaces of any description over 10 cm width and girth not otherwise described and applying two coats of syntrhetic enamel paint over a coat of red oxide zinc crome complete all as specified and as directed.

M&L for preparing of old steel surfaces of any description over 10 cm width and girth not otherwise described and applying two coats of syntrhetic enamel paint over a coat of red oxide zinc crome primer complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 100 mm thick cement concrete type B-2, 1:2:4 using (40mm graded crushed stone aggregate) as in floor finishes complete all as specified and as directed.

Dismantling of mild steel work of any descriptioncomplete all as specified and directed by Engr-in Charge.

M & L for MS work in tubular trusses including special shape washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade st-240 complete all as specified and directed by Engr-in Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in Charge.

M&L for sceed bed or bedding layer of cement mortar 15 mm thick 1:6 for laying floor finishes complete all as specified and directed by Engr-in Charge.

M&L for sceed bed or bedding layer of cement mortar 10 mm thick 1:4 for laying wall finishescomplete all as specified and directed by Engr-in Charge.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for Joint free Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

Taking down of chowkats with shutter (without taking of shutter from frame) n.exc 1.5 Sqm each complete all as specified and directed.

Taking down of chowkats with shutter (without taking of shutter from frame) exc 1.5 Sqm but n.exc 4.0 Sqm each complete all as specified and directed.

S&F 2nd class hard wood, Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Resecuring or easing & adjusting of door shutter of any description without taking down exc 1 Sqm but not exc 2 Sqm including Taking down and refixing in same position completed all as specified and directed by Engr-in-Charge.

M&L for Glazed and skelton Windows, ventilators shutters 30 mm thick 2nd class soft wood, open rebated and prepared to receive glass, guage, etc, divided into square with plain, chamfered or rounded mitred and rebated sash bars, any numbers, size of members of shutters as specified in SSR Part I Section 8 clause 8.20 (b) as in windows complete all as specified and as directed.

S&F plain 2nd class hardwood 30mm thich framed, flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

M&L for preparation of previously treated wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by Engr-in Charge.

S&F 100mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by Engr-in Charge.

S&F 300mm long, aluminium alloy, anodised, sliding door bolt with hasp and staple complete all as specified and as directed.

S&F stainless steel butt hinges 100mm long complete all as specified and as directed.

S&F stainless steel butt hinges 75mm long complete all as specified and as directed.

S&F extruded aluminium alloy handle fabricated type anodised of size 125mm complete all as specified and as directed.

S&F extruded aluminium alloy handle fabricated type anodised of size 100mm complete all as specified and as directed.

Dismantling water tanks exc 500ltr but not exc 1000ltr capacity, removing to store complete all as specified and directed by Engr-in Charge.

S&F rotantional moulded polythylene water storage tanks 1000 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections, complete all as specified and as directed by the Engr-in-Charge

Taking up or down 20mm dia steel tubing and connections,complete all as specified and as directed by the Engr-in-Charge

S&F 3 layer PP-R Polypropyene random copolymer outer dia of pipe 16 mm pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, celling or in floors etc complete all as specified and directed by the Engineer -in-Charge

S&F 3 layer PP-R Polypropyene random copolymer outer dia of pipe 20 mm pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, celling or in floors etc complete all as specified and directed by the Engineer -in-Charge

S&F in repair 15mm bore PVC connection pipe, 450mm long complete all as specified and as directed by Engr-in-Charge

Supply and fixing in repairs Bib taps, cast copper alloy with handle, chromium plated fancy type, with wall flange screwed down, suitable for 15 mm bore pipe, complete all as specified.

Supply and fixing in repairs Angular/ stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, , complete all as specified.

S&F PVC (SWR) pipes 110mm dia, single socketed in any length with rubber ring joints fixed to walls including dismantling of existing pipe complete all as specified and directed by Engr-in-Charge

S&F 110mm PVC (SWR) bends any radius all as specified and directed.

S&F in repair vitreous china wash hand basin including brackets, white of size 550 x 400 mm incl cutting for and pinning in ends of brackets including waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and fixed complete all as specified and directed.

M&L for Veneered decorative plywood, 6 mm thick 5 Nos of ply grade 1 (with BWR resin) with decorative face veneers on one face fixed with nails to timber frame work as in ceiling complete all as specified and as directed.

M&L 75 mm thick cement concrete type C-2, 1:3:6 (using 40 mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as spd and directed.

Material & labour 10mm thick rendering in cement mortar 1:4 on brick or concrete wall surfaces of any description receive for wall tiles complete all as specified and directed by Engr-in Charge.

S&F for SDC Laminated flooring 8mm thick of any coloured manufactured by Direct Pressure Laminated (DPL) wherein the empty Abrasive aluminium oxide overlay alongwith metamine impregnated decorated film is directly fused with the back with flooring locking profile in designed with double click locking system on the length and single locking width alongwith desire locking strength as directed by the Engr-in-Charge.

Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engr-in-Charge

M & L Precast cement concrete solid block made of cement concrete type C1 1:3:6 using (20mm graded stone aggregate) in masonary , exc. 10cm in width and, setting in cement mortar 1:6 complete all as specified and directed by Engr-in Charge.

M&L for 10mm thick rendering on fair faces of Brick or stone masonry surface in cement mortor 1:6 finished even and smoth without using extra cement complete all as specified and directed by Engr in Charge

M&L for Rendering 15mm thick, in cement mortar 1:4 on PCC block walling or concrete surfaces and finished even and fair without using extra cement complete all as specified and directed by Engr-in Charge.

M&L for preparation of newly plastered surfaces and apply two coats of cement base paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces and apply three coats of white wash complete all as specified and directed.

M&L for mild steel framed work as in doors / windows or gates of angle, with gusset plates, rails, braces etc. complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or covering runnig rails and guides) and hanging also fastening and fixing complete conforming to Fe 410-W (Gde-E-250) quality A complete all as specified and directed.

S&F 1mm thick mild steel plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes, punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc complete all as specified and directed

Dismantling water tanks exc 250 ltr but not exc 500 ltr capacity and removing to store complete all as specified and directed by Engr-in Charge.

S&F Rotational moulded polyethylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engr-in Charge.

Providing & fixing false ceiling with semi perforated 12mm thick micro tegular edged GRG at all heights with GRG false ceiling tiles of size 595X 595mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99% NRCO 0.50 to 0.75 as per IS 8225:1987,Noncombustible as per BS476(part4)-1970 and light reflectance of 85%(min) to be laid in true horizontal level suspended on inter locking metal T-grid of hot dipped galvanised iron section of 0.33 mm thick (galvanised @ 120 grams per sqm incl both sides) comprising of main -T runners of size 15x 32 mm of length 3000mm ,cross-T of size 15X32 mm of length 600 mm to form grid module of size 600 x600 mm suspended from ceiling using galvanized mild steel items (galvanizing @80mm per sqm ) i.e 50mm long 8 mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85 x 25 x 2 mm ,Galvanised iron perimeter wall angle of size 24 x 24x 0.40 mm of length 3000 mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws.The work shall be carried out as per specifications, drawings and as per directions of the Engr-in-Charge.

M&L for 2nd class soft wood fillets sectional area exc 3 sqcm and n exc 6 sqcm rectangular or triangular in section but bullnosed, splayed, chamfered or rounded on one edge of face, secured with nails or brads, complete all as specified and as directed.

S&F plain 2nd class hardwood 35mm thick framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 125mm long Aluminium, anodised, barrel tower bolt, Mild steel or stainless steel having dia/shoot not less than 10 mm with screws complete all as specified and directed.

S&F of 250mm long, Mild steel or stainless steel, sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc and n.exc 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

M&L for cement concrete type D2 1:4:8 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in Charge.

M&L Precast cement concrete block masonry in super structure type C1 1:3:6 (using 20mm graded crushed stone aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:4 complete all as Specified.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and directed by Engr-in Charge.

M&L for preparation of steel surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint one coat of red oxide primer and two coats of synthetic enamel (ordinary tint) complete all as specified and directed by Engr-in Charge.

S&F Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splays between floors and beams, etc complete all as specified and directed by Engr-in Charge.

M&L for Mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in Charge.

Description all as per item Srl No. 77.00 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engr-in Charge.

M & L for providing RCC M- 25 (nominal mix) (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed.Engr-in -charge

M&L Hardcore of broken stone or boulder of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by Engr-in Charge.

M&L 100mm thick Cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) in floor complete all as specified and directed by Engr-in-Charge

S&F 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in Charge.

S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed by Engr-in Charge.

S&F Aluminium alloy 250 anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in Charge.

S&F in repair 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified and directed by Engr-in Charge.

M&L vitreous China squatting pan ‘Orissa’ pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe(excluding flushing cistern and flush pipe complete all as specified and directed by Engr-in Charge.

S&F PVC low level white flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, brass screws, handle etc with flush pipe of polyethylene of low density 32 mm dia of suitable length and making all connection complete all as specified and directed.

S&F Viterous China WHB 550 x 400mm size flat back including cutting for and pinning in ends of brackets or erecting stand CP Pillar tap 15mm, CP Waste coupling 32mm, PVC waste pipe 750mm long and brackets complete all as specified and directed by Engr-in Charge.

S&F 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engr-in Charge.

S&F floor trap of PVC 75 mm out let dia with grating and jointed to waste pipe complete all as specified and directed by Engr-in Charge.

M&L for PVC (SWR) 110 mm gully trap setting jointing with solvent cement complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

S&F 20 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in Charge.

S&F 3 layer PP-R Polypropyene random copolymer outer dia of pipe 25 mm concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall s, ceilins or in floors etc.complete all as specified and directed by Engr-in Charge.

Supply and fix in 15mm bore pillar taps CP brass chromium plated fancy type screwed down high pressure with chromium plated screwed shanks and fly nuts complete screwed for iron pipe in repairs all as specified and directed.

M&L Plain cement concrete 1:3:6 Type C-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes including packing under and hunching against the sides of pipes after they are laid and tested for 150 mm bore SGSW pipe complete all as specified and directed by Engr-in Charge.

S&F 150mm dia, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Excavating over areas, exc 1.5 m and n.exc. 3.00m deep and getting out in hard/dense soil complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M& L for Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, build in cement mortar 1:6 complete all as specified and directed.

M& L for Walling of random rubble, uncoursed, well bonded, laid dry in retaining walls, abutments and similar works complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finish and flat surfaces not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engr-in Charge.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, rough finished surfaces of concrete complete all as specified and directed by Engr-in Charge.

M & L for providing RCC M- 25 (design mix) (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in Charge.

M&L for Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in coping, benching bed plates and the line including necessary form work and finishing all exposed surface of concrete as per clause 4.11.16.2(a) of SSR Part-I(1991) complete all as specified and as directed.

S&F 150mm dia bore PVC (SWR) branch piece, single (single Y) equal or unequal, complete all as specified and directed.

M & L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded agg) as in cover slab for manholes set in CM 1:4 including necessary form work complete all as specified and directed by Engineer in Charge.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B-1 smooth finished, and reforming benhing as required for 150mm bore pipe complete all as specified and as directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials such as fitting & fixture from the site and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheathed electric cable 1100 volts in and including PVC casing and capping of 25 mm and above (as per conductor run )with all fittings/ accessories and including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including 50 mm deep box made of 2nd class hard board of required size and shape etc covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point, bell, exhaust point, bulk head, independent controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

Description all as per item No. 112.00 here in before but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

Description all as per item No. 112.00 here in before but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

Description all as per item No. 112.00 here in before but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement switch piano flush button single pole one way 5 Amps complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement socket outlet 2 in 1, 5 Amp, flush type completeall as spe cified and as directed by Engr-in-charge.

Supply and fixing in replacement switch, socket combination 2 in 1, 5 Amp, flush type completeall as specified and as directed by Engr-in-charge.

Supply and fixing in replacement switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing in replacement angular lamp holder, PVC/Polycaronate type with back plate suitable for 9 watt LED bulb for batten fittings complete all as specified and directed by the Engineer-in-Charge.

Supplying and fixing in replacement LED 9 Watt complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement LED batten lights fitting 1x 20W, 220V,AC decorative type including LED tube light connecting up with three core flexible copper conductor cable of suitable size including ceiling rose complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing new energy saving LED Bulk head fitting 10 watt made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK07 as reqd to be mounting bracket in wall/floor to suit the opening of the fitting with FI clamp, nut, bolt and washers of suitable size including making connection complete all as specified and as directed by Eng-In-Charge.

Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling 6500K including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed by Eng-In-Charge.

Supply and fixing in replacement sheet Metal enclosure single shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint all as specified and as directed by the Engr-in-charge.

Supply and fixing in replacement sheet Metal enclosure single shutter type for DB’s 240 Volts Single Pole and Neutral 4 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint all as specified and as directed by the Engr-in-charge.

Supply and fixing in replacement MCB single pole and neutral 32 to 40 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement MCB single pole 5 to 30 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all specified and as directed by the Engineer-in-Charge.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 1991 Part-I and connecting to CBDB’s as specified or indicated including testing on completion complete all specified and as directed by the Engineer-in-Charge.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 10 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 15cm after laying, streching & testing of cable in trenches complete all as specified and directed by Engr-in-Charge. Note :- Only punned thickness i.e 18cm shall be measured and paid.

M/S BILAL AHMAD BHAT

N K BUILDERS

M/S ZTECH

M/S WEB COMPNAY

M/S GLOBAL ENGINEERS

SUMEET TRADING CORPORATION

M/S LIBE & CO