ADDITION/ALTERATION AND SPECIAL REPAIRS TO CERTAIN BUILDINGS AT ARTY CENTRE, HYDERABAD

Dismantling of single layer mangalore pattern or similar tiles laid dry in roofing and including battens of any size and tilting fillets n. exc. 15 cm centre to centre complete all as specified and directed.

Dismantling of AC sheets / Galvolume sheet / GI Sheet of corrugated or semicorrugated etc. sheets in roof coverings

M&L 2nd class hard wood, clean sawn, in scantiling timber framed and fixed with nails and including dismantling complete all as specified and directed

M&L 2nd class hardwood clean sawn battens at 25 cm centres, sectional area exc. 15 and n. exc. 25 Sqcm complete all as specified and directed.

M&L roof tiles, mangalore pattern interlocking at side joints laid dry complete all as specified and directed.

Supply and install hi wall split units 1.5 T indoor/outdoor with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating complete all as specified and directed.

M&L ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:4 complete all as specified and directed.

M&L preparation of old painted wooden surfaces of any description over 10 cm width or girth not otherwise described and including applying one coat of synthetic enamel paint complete all as specified and directed. .

S&F MS angle sections as in posts main and cross beams, hip and jack rafters; purlins where connected to common rafters and drilling holes for existing wooden / steel angle rafter; fixed with angle cleats MS Screw bolts necessary welding to purlins or other connecting plate of Grade Fe 410 -W (Gde- E- 250) quality- A etc, complete all as specified and directed.

M&L steel work in tubular trusses & vertical post and including special shaped washer etc, using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade st-240 complete all as specified and directed.

All as per Sl. Item No. 5 above but fixing only. NOTE: Serviceable quantity shall be reused under this item.

M&L preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and including applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

Dismantling of boarding, any description fixed in any position with nails complete all as specified and directed.

M&L false ceiling at all heights false ceiling tiles of size 595 x 595 x12 mm of approved texture, design and patterns having moisture contents less than 2% humidity resistance of 99% NRCO.50 to .75 as pe IS8225:1987, Noncombustible as per BS 476 (Part 4)-1970 and light reflectance of 85% (Minimum) to be laid in true horizontal level suspended on interlocking metal T Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanised @ 120 gms per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000 mm, cross -T of size 15 x 32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspened from ceiling using galvaized mild steel items (galvanizing @ 80 grams per sqm) i..e 50 mm long, 8 mm outer diameter M-6 dash fastener 6 mm dia fully threaded hanger rod upto 1000 mm length and L-swhape level adjuster of size 85 x 25 x 2 mm galvanised iron permieter wall angle of size 24 x 24 x 0.40 mm of length 3000 mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm ceneter to centre and 50 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down cement plaster on wall of any desdriptions incl racking out joints for key scrubbing with water etc. and remove all the debris from site and rubbish off the premises complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in

roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 and including demolition complete all as specified and directed.

M&L rendering 15 mm thick in two layers (10+5) cement mortor 1:4 (1 cement 4 river sand) on concrete or brick wall surfaces, finished even and smooth without using extra cement, mixed with WPC complete all as specified and directed. NOTE: Supply only WPC shall be measured and paid seperately.

M&L 10 mm thick rendering in CM 1:6 on brick wall surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L preparing new plastered wall surfaces and including applying two coats of cement based paint complete all as specified and directed.

M&L preparation of new ceiling surfaces and including applying three coats of white wash complete all as specified and directed.

M&L 10 mm thick rendering in CM 1:3 as in ceilings, concrete surfaces finished fair and even complete all as specified and directed.

M&L preparing newly plastered wall surfaces and including applying 3 mm thick (two layers 1.5 mm each coat) wall care putty to fill up the depression and rubbing with sand paper to achieve a levelled and smooth surface and including applying two coats of OBD over a coat of chalk whiting primer complete all as specified and directed

M&L complete removal of existing treatment on walls and including applying two coats of cement base paint complete all as specified and directed.

M&L preparation of old stone masonry surfaces of walls, any description and including applying two coats of cement wash with portland cement slurry to smooth bodied opaque finish complete all as specified and directed.

M&L mirror polishing on marble / granite / Kota stone / stone work where ever required to give high gloss finish complete all as specified and directed.

M&L roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and including brushing neat cement slurry with 3 kg of cement per Sqm complete all as specified and directed.

M&L complete removal of existing treatment on walls and including applying 3 mm thick (two layers 1.5 mm each coat) wall care putty to fill up the depression and rubbing with sand paper to achieve a levelled and smooth surface and including applying two coats of oil bound distemper over a coat of chalk whiting primer complete all as specified and directed.

Supply only liquid for water proofing compound

M&L preparation of old ceiling surfaces and including applying two coats of white wash complete all as specified and directed.

M&L water proofing treatment with APP based polymeric membrane minimum weighing 3 kg / sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified with non woven polyester matt black finished over compatiable primer at 0.3 litre per sqm, torching the membrane on whole surface uniformly while unrolling the membrane by LPG and sealed with trowel after necessary preparation of surface complete all as per manufactures instructions and finally finished with at coat of bitumastic aluminium paint over the membrane. The over lap joint shall be provided of 100 mm in longitudinal direction and 150 mm in tranverse direction respectively. All the angles, abutments and the drainage outlets shall be sealed with extra care to ensure full bondage complete all as specified and directed. Note : The work shall be carried out by authorized applicators of manufacturers.

M&L hard core of guage n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L chequered rubber moulded cement concrete tiles 30 cm x 30 cm x 25 mm thick with grey cement and pigment, machine pressed, set jointed and pointed in neat cement slurry in floors and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2 (Using 40 mm graded granite stone aggregate) as in plinth protection / hardstanding finishd even and smooth with out using extra cement and including demolition complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, plinth Protection, aprons etc Laid, bed-ded and pointed in any mortar,complete all as specified and as directed and remove all the debris from site and rubbish off the premises complete all as specified and directed.

M&L pre polished machine cut kota stone slab 20 to 25 mm thick in single piece to the full width of tread and riser. Tread kota stone shall be provided with bull nosing and 02 nos of 5 mm thick anti skid grooves at one side of tile and including 10 mm thick screed in CM 1:3 over cement slurry over RCC slab / waist slab complete all as specified and directed.

M&L 20-25 mm thick pre polished machine cut Kota stone slab in riser of step, skirting, dado & pillar and including 10 mm thick backing coat in CM 1:3 & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L mild steel TMT bars 10 mm dia and over, cut to length bent to shap required and including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook and including making connections and fixed in position complete all as specified and directed. Make: Cat No F100110 of Hindware / Cat No BEA-40 of Prayag

S&F in repairs 15 mm dia fancy type stop valves / angle cock chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Make: Cat No F360006 of Hindware / Cat No 8510 of Prayag

M&L PCC 1:4:8 Type D2 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame exc. 1.5 Sqm and n.exc. 4 Sqm each complete all as specified and directed.

All as per Sl. Item No. 13 above but plain steel sheet.

S&F pressed steel door frames 125 x 60 mm doors with one or more rebates and including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.

Excavating in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth, n. exc.10 sqm on plan for foundation, laying of cables etc, and getting out in hard / dense soil complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed withn wooden beading or with nuts and bolts to existing steel windows / wooden windows complete all as specified and directed.

S&F 5.5 mm thick glass fixed in aluminium door / window / ventilator with aluminium beading complete all as specified and directed.

M&L 12 mm thick pre-laminated, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to aluminium frame with aluminium beading complete all as specified and directed.

M&L second class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc, divided into squares with plain chamfered or rounded and rebated sash bars any numbers complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles fabricated type anodized complete all as specified and directed.

S&F 200 mm alluminium anodized barrel tower bolts extruded section complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

S&F 150 mm floor door stopper of aluminum alloy body & tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M S Square tube, in opening as per manufacturers instructions complete all as specified and directed.

S&F factory made solid panel laminated PVC door shutter 30 mm thick (style) consisting of frame made out M.S tube for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail: panelling of plain colour PVC sheet to be fitted in the M.S frame welded / scaled the stiles & rails with suitalble PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specifications & drawing complete all as specified and directed.

S&F 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed.

S/F 150 mm size aluminium anodised handles, fabricated type complete all as specified and directed.

S&F in repair stainless steel curtain rod 19 / 20 mm dia and including mild steel chromium plated brackets and making good the dusturbed surface complete all as specified and directed.

All as per Sl. Item No. 150 above but 70 Sq mm 3.5 core

All as per Sl. Item No. 142 above but 2 feet 10 W

S&F sheet glass 4.8 mm thick and glazing with oil putty / alu beads n.exc. 0.50 sqm each pane (alu beads will be measured under alu doors/ windows) complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) doors frames, shutters windows frames sliding shutters, ventilators, grills and partitions (fixed portions) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size and including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required and including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed.

All as per Sl. Item No. 74 above but 75 mm bore.

Preparation of new or previously untreated wooden Surfaces of any description not otherwise described over 10 cm width or grith and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) etc for rough finished surfaces of flat concrete complete all as specified and directed.

M&L 60 mm thick M-35 grade factory made rubber moulded precast concrete interlocking paver block in grey cement with pigments and of approved size and shape and conforming to IS 15658-2006, with and including 50mm thk sand bedding layer laid to true line, level watered and mechanically compacted etc, and including dismantling complete all as specified and directed.

M&L preparing new or old mangalore tiles surfaces and including applying two coats of exterior grade weather proof paint over a coat of

primer complete all as specified and directed.

M&L 10 mm thick vitrified ceramic coloured tiles, light shade (Square or rectangular) polished, area of each tile not exc. 0.36 Sqm as in floors etc, and including 15 mm hick cement screed bed in CM 1:6 and jointed in neat slurry and pointed in white or coloured cement to match and dismantling complete all as specified and directed.

All as per Sl. item No. 80 above but n. exc. 1.5 Sqm each.

All as per Sl. item No. 83 above but 105 x 60 mm.

All as per Sl. Item No. 90 above but in repairs

All as per Sl. item No. 108 above but in skirting / dado etc, and 10 mm thick backing coat in CM 1:4

All as per Sl. Item No. 114 above but one 3 pin 6 Amps switch socket outlet point controlled by one switch on independent board.

M&L point wiring for one light / fan point controlled by one switch complete all as specified with 1100 Volts grade 1.5 Sqmm PVC insulated FR-LSH unsheathed cable with multistranded copper conductor conforming to IS:694:1990 with ISI marking in and including PVC rigid conduit medium grade of size minimum 20 mm with all accessories concealed in wall / ceilling, continous earth wire 1.5 Sqmm PVC insulated FR-LSH unsheathed 1100 Volts multistanderd copper conductor connected to common earth and dolly, necessary modular metal flush boxes concealed in walls and modular white plate covers with frame for mounting for modular switches / sockets / fan regulators etc, for one light point controlled by one switch one way and including taking down existing complete all as specified and directed.

S&F modular switch 1 way 6A, 1 module complete all as specified and directed.

S&F modular switch 1 way 16A with indicator, 1-module complete all as specified and directed.

S&F modular socket, shuttered type, 6A - 3 pin 2 -module complete all as specified and directed.

S&F modular socket, shuttered type, 6/16A - combined 2-module complete all as specified and directed.

S&F modular switch 2 way 6A,1 module complete all as specified and directed.

S&F modular bell push 6A 1 module complete all as specified and directed.

S&F bell, Ding Dong AC. 230 volts, single pole complete all as specified and directed.

S&F power module 240V, 20A complete with 4 module metal flush box, cover plate, Starter, Plug & Socket complete all as specified and directed.

M&L taking down ceiling fan, ceiling cable end and including dismantling blades and over hauling the fan, provide grease to bearings, improve the insulation of winding and blades to store, painting of ceiling fans with synthetic enamel paint by spray machine after cleaning all dust and refixing of ceiling fan & connecting up including provision of cable from ceiling rose or connector to fan etc. complete all as specified and directed.

All as per Sl. Item No. 150 above but 35 Sq mm 3.5 core

S&F MCB ('B' curve) 6- 32 A, 230 V, 50 Hz, SP for conforming to IS/IEC 60898-1-2002, having breaking capacity Icn = 10 kA, sliding bottom clamp, colour coded on/off indication on dolly, bi-connect IP 20 protected lower terminals and sliding shutters, etc. complete all as specified in IS 732: 2019 and directed.

M&L RCC (Design mix) Grade M25 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings balconies canopies, desk slabs and in shelves and the like and including demolition complete all as specified and directed.

S&F 3 pin, 6A, 230 V ceiling rose conforming to IS 371:1999 and having terminal capacity 3 x 1.5 mm2 with IK 04 and IP 20 protection as specified in IS 732 : 2019 complete all as specified and directed.

S&F RCBOs for earth leakage, overload & short- circuit protection 6-32 A, 230 V, 50 Hz, 2P, 100 mA rating complete all as specified in IS 12640-1 (2008) and directed.

S&F RCBOs for earth leakage, overload & short- circuit protection 32 A, 415 V, 50 Hz, 4P, 30 mA rating complete all as specified in IS 12640-1 (2008) and directed.

S&F MCCB, 415 V, 16KA, 4 Pole, 63 Amp complete all as specified and directed.

All as per Sl. Item No. 114 above but one 3 point 6 Amps switch socket outlet point controlled by one switch on the same board.

Taking down chowkats with shutters and resecuring or easing and adjusting of chowkat and shutters and inclding refixing in same opening exc. 1.5 Sqm n. exc. 4 Sqm each complete all as specified and directed.

Note: Cost of cutting chases in walls and making good for concealed wiring and cost of modular boxes with cover plates is deemed to be included in the quoted rate.

M&L submain wiring using 2 runs 4 Sqmm of FR-LSH grade PVC insulated, unsheathed, stranded, copper conductor cable conforming to IS 694 : 2010 and one run of 4 Sqmm FR-LSH grade PVC insulated, unsheathed, stranded, single core, copper wire to be drawn in and including suitable PVC Conduit (medium grade) in concealed wiring of suitable size, making good of disturbed surface of wall / ceiling / floor and taking down complete all as specified and directed. Note : 2 runs of 4 Sqmm copper wire, 1 run of 4 Sqmm copper wire & one run PVC Conduit shall be measured as one unit

S&F exhaust fan made of sturdy Engineering plastic body complete with louvers shutter, voltage 350 RPM, 4 module 230V, 50 Hz, RPM 1200, copper winding of sweep 250 mm sweep and including making suitable size hole in wall complete all as specified and directed.

Taking down existing LED batten 20W and including keep in safe custody and refixing the same in existing location after completion of repairs complete all as specified and directed.

S&F electronic type fan regulator stepped socket type, suitable for BLDC fan to work on 230 volts complete all as specified and directed.

M&L GI tubing medium grade 40 mm bore concealed on both side walls for hanging ceiling fan and including provision of hook complete all as specified and directed.

S&F TV co-axial socket outlet fixed to wall on hylem sheet complete all as specified and directed.

S&F factory made prewired TPN 4 ways distribution board in sheet steel enclosure vertical double door with suitable rated bus bar, 240 Volts suitable for housing TPN MCBs as incomer and SP MCBs as outgoing and including taking down complete all as specified and directed.

All as per Sl. Item No.114 above but one light point controlled by two nos, 2-way, 6 Amps switch.

S&F ceiling fans complete with blades, down rod and accessories, 230 V, 1200 mm sweep 30W, 350 RPM, 4 module. Min air delivery 225 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete all as specified and directed. Make : FAB BLDC ULED of havells / Crompton Greaves / Usha.

S&F single pole & neutral, double door, metallic distribution board 12 ways conforming to IEC 61439-3, suitable for flush / surface mounting with provision for DP RCCB / RCBO / Isolator / MCB as incomer and SP MCBs as outgoing, reversible metal door, 100 A copper busbar, fully shrouded neutral bar, earth bar, wire set & cable ties for cable management, pre fitted masking sheet, etc. having IK 09 & IP 43 protection and including taking down complete all as specified in IS 732: 2019 and directed.

S&F LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling and including connecting up with driver three core flexible copper conductor cases of suitable size and including taking down complete all as specified and directed. Make : VENUSTREND2X2PLR36WLED857SWH of Havells / or equivalent in Wipro / Philips

S&F rigid non-metallic PVC conduit of dia 20 mm exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc

S&F 35 W security light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 110 lumen/Watt, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry and including wall mounting with bracket arm OD 35 mm to 42 mm, necessary electrical connection to the fixture with 3 core flexible copper conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

M&L electrical earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25 m deep below normal GL) with top edge of the earth plate at a depth not less than 1.5 m below normal GL and including connected to GI wire 4 mm dia by means of bolts, nuts, washers made of galvanized iron connected to earthing to body of equipment /DBs, GI wire protected by 15 mm dia light grade GI pipe upto connecting point and watering arrangements with 20 mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No. 3. of MES Schedule (SSR) Part I complete all as specified and directed.

S & F Telephone socket modular type with modular plate & metla box

S&F 20 W surface / wall mounted LED batten having PC diffuser, luminous efficacy of minimum 120 lumen/W, CRI > 80, PF > 0.9, CCT 6500K, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing. white coloured ABS end caps, IP 20 protection, input voltage range 140- 270 V, input frequency 50- 60 Hz, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture and including taking down complete all as specified and directed.

All as per Sl. Item No.114 above but one bell point controlled by one bell push.

All as per Sl. item No. 114 above but with cable 4 sqmm multi stranded copper FR-LSH wire, 1100 Volts grade, unsheathed for one 3 pin socket out let 16 amps on independent board including, continuous earth wire PVC insulated 4 sqmm copper stranded conductor FR-LSH, 1100 Volts grade.

All as per Sl. item No. 132 of above but 6 sqmm cable. Note : 2 runs of 6 Sqmm copper wire, 1 run of 6 Sqmm copper wire & one run PVC Conduit shall be measured as one unit

S&F 17 W surface / LED mirror light, having PC diffuser, luminous efficacy of minimum 120 lumen/W, CRI > 80, PF > 0.9, CCT 6500K, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS 15885 (Part-2 / Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing. white coloured ABS end caps, IP 20 protection, input voltage range 140- 270 V, input frequency 50- 60 Hz, and including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture and including taking down complete all as specified and directed. Make : Philips Photon Mirror Light , product SKU : 919215850968 or equivalent in Havells / CG / Bajaj.

S&F LED light fitting 1 x 9 W / 1x 10 W bulkhead luminaires and including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size and including taking down complete all as specified and directed.

including taking down complete all as specified and directed.

Supply, laying and testing cable of size 95 sq mm 3.5 core, XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor and

M&L sand cushioning to under ground cable with dry sand complete all as specified and directed. Note. Punned thickness of sand to be considered for measurement purpose.

Supply and laying burnt bricks sub class "B" of old size laid dry in trenches complete all as specified and directed.

M&L earthing complete with galvanized steel each plate electrode 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less then 2.25 m deep below normal ground level) with top edge of plate not less then 1.5 m below noramal ground level, earth plate connected to GI strip of 32 x 6 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate no 3 of MES SSR-2009 (part I specifications) connected to eath test point all as specified or indicated including tesing on completion, including necessary exavation and earth work in any type of soil and adequate quantity of commen salt & charcoal for alternate layer arround the earth plate, including PCC (1:2:4) pit and 10 mm thick C.I cover with arrangement of hinge to 40 x 40 x 6 mm C.I angle iron frame, including 20 mm dia C.I pipe for watering purpose with the arrangement of funel and wirw mess, including G.I pipe of 15 mm dia for earth lead protection and including taking down complete all as specified and as directed.

Note : the rate is deemed to be inclusive of the cost of earth work exavation on any type soil and removal of surplus soil to a distance of 50 m, PCC 1:2:4 type B1 for earth pit cover 6 nos. 8 mm dia TMT bars on both direction, earth lead protection GI pipe medium grade with suitable size from earth plate electrode to main switch, GI wire length up to 7.50 m will measured as one unit

Note : The quoted rate is deemed to be inclusive of the cost of earth work exavation on any type soil and removal of surplus soil to a distance of 50 m, PCC 1:2:4 type B1 for earth pit cover 6 nos. 8 mm dia TMT bars on both direction, earth lead protection GI pipe medium grade with suitable size from earth plate electrode to main switch, GI wire length up to 7.50 m will measured as one unit