Special Repair of Commissioner Residence at Hisar in Hisar District (Civil and PH Work)

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (HSR 8.5(b) In cement

Dismantling roofing: demolishing mud phaska in tile terracing. (HSR 8.8 (g)

Removing doors and windows (wooden and steel) together with the Dismantling of walls (HSR 8.17a) a) Door

b) Window

Scraping of White wash and colour wash (HSR 8.32 (a)

Scraping of Cement plaster (HSR 8.32 (c )

Cement concrete 1 : 8 : 16 with stone aggregate 40 mm Nominal size in foundation and plinth.. (HSR 10.28)

Cement concrete 1: 2 : 4 with stone aggregate 20 mm nominal size in foundation and plinth. (HSR 10.41)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. (HSR 11.9)

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Precast chequered tiles of 20 mm thickness In ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings. (HSR 14.45 + Note)

Fixing of White Marble stone flooring 17 mm & above thick slab including matching grains of marble laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of marble including rubbing and polishing (using marble stone slab soze more than 0.38 sqm each) (HSR 14.49) (LR) (Marble will be supplied by the Department).

Kotah stone flooring minimum 25mm thick in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.89)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in skirting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.90)

Pdg. & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in floors, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.91)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete.(HSR 14.92 (b) Size of ceramic Glazed tiles 300 X 450mm

Laying and fixing Granite stone in all shades,15mm to 18mm thick in skirting/ dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite including labour for fixing cramps pins and dowels etc. (excluding the cost of granite stone) (HSR 14.95) (LR) (Granite will be supplied by the Department).

15 mm thick cement plaster 1:6 on the rough side of single of half brick wall (HSR 15.12)

Cement pointing 1:2 deep variety on brick and Tile work (HSR 15.60)

Cement pointing 1:2 flush on brick and tile walls. (HSR 15.62)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.(HSR 16.3)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79(b) 1st quality

Providing and laying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including coat and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K./Birla make) (HSR 16.81)

Providing and fixing sliding bolt with nuts and screws etc. complete- (HSR 17.83 (c)(ii) c)iron (ii)size 250 mm x 16 mm

Factory manufactured paneled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., c(non –coniferous timber other than team, conforming to I.S specification no. 1003 kiln seasoned), with 100 mm wide vertical syltes, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick commercial veneered both sides particle board or plywood of B.W. R. grade, hot-pressed, including cost of iron hinges, screws, chocks/cleats, stops and nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in positon:- (HSR 17.91 (c)(-) Note 30mm thick

Factory manufacture solid flush door and Shutters, with block board core as per I.S. No. 1659-1969 bonded with water poof type phenol formal dehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in positon includeing iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (HSR 17.93 (a) (iii) (-) Note commercial veneering with vertical grains or corss bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (iii) 35mm thick

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Supplying M S Bolts of required sizes with nuts and washers complete. (HSR 18.15 (a)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, or approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- (HSR 18.34) (a) door and window frame of size 89 mm X 50 mm with 40 mm wide single rebate

(c ) door and window frame size 127 mm X 50 mm with 40 mm wide double rebate

PUBLIC HEALTH WORK Providing fixing PVC Rain water pipe 6Kg Pressure of ISI mark in cement mortar during masonry work. (HSR 13.89 (b) (b) 150 MM dia PVC pipe 6 Kg. Pressure.

Providing & fixing PVC Bend ISI Mark. (HSR 13.90 (a) 100mm dia PVC Bend

Labour for fixing G.I or W.I pipe sleeve pieces in holes in walls, floors, and roofs rounds pipes including all cutting and wastage. (HSR 28.27 (a) a) 15 mm internal diameter of sleeve pipe

b) 20 mm internal diameter of sleeve pipe

Construction brick masonray inspection chamber sizes as given below upto 0.60 metres average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plastern 1:2 with a floating coat of 1 mm thick of neat cement RCC 1:2:4 slab 100mm thick/C.C. topping 50mm thick with 455 mm x 455 mm / 455 mm x 610mm inside light duty C.I inspection chamber cover and frame weight as per I.S.I specification painted with 3 coats of black bitumastic superior paint complete as per standard design. (HSR 29.84 (a) (c ) a) Size inside (with 455mmx455mm cover and frame light duty single seal weighing 20 kg with C.C topping. c) 600 mm x 900 mm

Providing and fixing in position best Indian make Indian type orissa or orya water closet suite complete with 100mm HCI 'P' trap other necessary fittings. (HSR 30.2 (a) a) Size 580mm I) White.

Providing and fixing in position best Indiann make European type water closet with concealed 'P' or 'S' trap with or without vent (as approved by the engineer-in-charge) and all other necessary fitting as fully described in item no 30.3 above.) (HSR 30.6 (i)

PROVIDING AND FIXING IN POSITION INDIAN MAKE (ORDINARY) LAVATORY SUITES Consisting of Lavatory in VITREOUS CHINAWARE size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; complete in all respect as per (HSR 30.41 (iv) Size 550 mm x 400 mm with one no. tap

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the wells etcs. (HSR 30.70 (a) (ii) C.P. Brass (ii) Soad dish 380 mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71 (a) (i) INDIAN MAKE (i) 600 mm x 450 mm

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (HSR 30.75 (c ) bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) (HSR 30.76 (I) (a) (I) 15 MM STOP COCK (i) Stop cock male and female end

(ii) Concealed stop cock with flange

PROVIDING AND FIXING IN POSITION AUTOMATIC BRASSBALL VALVES IN TANKS (HSR 30.110 (a) (i) WITH COPPER BALL (i) 15mm internal diameter

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K. make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (except civil work). (HSR 30.119) (e) 1000 Litre Capacity

Supply & fixing of 3" P.V.C. pipe (NS)

Supply & fixing of 3" P.V.C. cowl (NS)

Supply & fixing of 3" P.V.C. Elbow (NS)

Supply & fixing, laying, jointing, fixing and testing G.I/P.V.C/W.I. pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading, Including cost of specials (NS) (i)15mm i/d pipeline

(ii) 20mm i/d

Pdg. & fixing of G.I. Union (NS) i) 15mm dia

ii) 20mm dia

RECOVERY ITEM: Bidders have to quote rates for recovery items at least or more than reserve price. The rates quoted against recovery will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Materials obtained from dismantling of structure have been calculated taking assumption of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) on approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. The reserve price is as under:- i) Doors i/c chowkats @ Rs.800/- each

ii) Windows & ventilator i/c shutters & chowkats @ Rs.500/- each

iii) Bricks @ 4/- each

iv) Bricks bats @ 350/- per cum Note: All quantities of the above materials have been worked out on the basis of theoretical quantities. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

Balwan Singh Contractor