GE 874/EWS-29/2024-25

Amount

Demolition of cement concrete (un-reinforced ) in ground floors and pavings n exc. 15cm thick.(Below or above ground level) complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

S&F galvanised corrugated 0.63mm thick mild steel sheeting with two corrugation side lap, fixed with coach screw and washer, in roofs, walls etc. of class 7 complete all as specified and directed. .

Dismantling timber scantling 40 Sq cm and over in section in any position in unframed work complete all as specified and directed. .

M & L for second class soft wood (kail) in scantling clean swan complete all as specified and directed.

Taking down chowkat with shutters exc.1.5 Sqm but n exc.4 Sqm (without taking off shutters from chowkhat) complete all as specified and directed.

M & L for second class soft wood plain, solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered, put together with glue penned and joints. complete all as specified and directed.

S&F plain framed, panelled shutters 35mm thick 2nd class softwood, (any numbers of panels), with panels of timber flats on both sides of veneered particle board med density, wood particle board with commercial face fitted to chowkat complete all as specified and directed..

Dismantling of boarding of any description fitted in any position with nails complete all as specified and directed.

S&F 20 mm thick 2nd class soft wood boarding, planed one side, with butt joints and fixed with nails in facia eaves boarding complete all as specified and directed.

Dismantling wall and ceiling board (fiber pulp, insulation, etc.) or insulation board /slab/ blankets, any thickness, including cover fillets complete all as specified and directed.

M & L for plywood, 6mm thick grade, BWR type BB fixed with nails to timber frame work in ceiling complete all as specified and directed.

M & L for Plain fillets of exc. 3 & n exc. 6 Sqcm, square rectangular or triangular in section, clean swan, secured nails complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over one coat of pink primer after preparing of new wooden surfaces of any description, not otherwise described over 10cm width or girth complete all as specified and directed.

M & L for MS barrel tower bolt, stove enamelled black, with bright bolt of 150mm long complete all as specified and directed.

M & L for MS Sliding door bolt, plate type, stove enamelled black, with bright bolt not less than 12mm dia of 250mm long complete all as specified and directed.

M & L for MS butt hinges med. Weight, cold rolled 100mm long complete all as specified and directed.

M & L for mild steel pressed handles, oval type, stove enamelled black of 125mm long complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L for 75mm thick plain cement concrete 1:4;8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base or floor complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick, area exc 0.06sqm but nexc 0.11 sqm of each tile in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in CM 1:4 over and including 25mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) complete all as specified and directed..

M&L for glazed ceramic coloured tiles (300x200x7mm) thick, as in vertical surface such as in skirting and dado etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate as in plinth protection finished even and fair without using extra cement complete all as specified and directed.

M & L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth (without using extra cement) complete all as specified and directed..

M & L for mild steel hold fast conforming to Fe 410-o or Fe-310-o suitable for fixing to stone/Concrete door or window frames complete all as specified and directed.

M & L for applying two coats of colour wash over one coats of white wash on newly plastered surfaces on wall including preparation of surface complete all as specified and directed.

M&L in repair for 10 ltrs capacity PVC valveless symphonic action type flushing cistern low level white with inlet ball valve, float and handle including brackets & PVC flush pipe 32mm bore complete all as specified and directed.

S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand complete all as specified and directed.

S&F in repairs 15 mm Pillar taps ,cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank and fly nuts screwed for iron pipes complete all as specified and directed.

S & F Vitreous China Wash down water closet pan (pedestal pattern) white, fixing bolts, flushing cistern and flush pipe, including black seat and cover, complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections complete all as specified and directed.

M&L 20mm tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L 15mm tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F in repairs Stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore pipe, complete all as specified and directed.

S&F in repairs bib taps cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule of 15mm bore, complete all as specified and directed.

S&F in repairs 20mm bore gun metal globe or gate valve with iron wheel head, screwed both ends complete all as specified and directed.

S&F in repairs PVC connection 15 mm length 450 mm fixed complete all as specified and directed.

S&F in repairs lagging to 15mm bore pipes used in internal water supply or plumbing all round with, 25mm thick bonded mineral wool preformed 'SNAPON' pipe section of density 144 Kg \cum conforming to IS 9842 along with chicken wire mesh netting 25 gauge, 20 mm mesh complete all as specified and directed.

All as per item No 39 above but 20mm bore pipe.

S&F in repairs 110mm PVC(SWR) P trap complete all as specified and directed.

Dismantling 100mm dia PVC pipes in any position complete all as specified and directed.

M&L for 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floors/walls as soil pipe complete all as specified and directed.

S&F 110mm PVC(SWR) bends complete all as specified and directed.

M&L for 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floors/walls as soil pipe complete all as specified and directed.

S&F 75mm PVC(SWR) bends complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap dia of outlet 75mm with grating including jointing with solvent cement complete all as specified and directed.

Surface dressing n. exc 15 cm deep and getting out in soft /loose soil complete all as specified and directed.

Excavation in trenches exc 1.50mtr in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n exc 10 sqm on plan and getting out complete all as specified and directed.

Returning filling including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for RCC (1:2:4) nominal mix as Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over and up to and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips. Gde- I, IS 432 (part I) complete all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 as in wall/septic tank/soakage well complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work, stone masonry or concrete surface, in cement mortar 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work, stone masonry or concrete surface, in cement mortar 1:6 finished the surface even and smooth without using extra cement , complete all as specified and directed.

Supply only liquid water proofing compound.

M&L for preparation of new plaster surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hardcore of gauge n. exc. 63mm deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface of broken stone or boulders complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection and finished even and fair, complete all as specified and as directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over 15 mm cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M & L for machine cut kota stone slab flooring 20-25mm thick over 15 mm cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

S& F plywood, grade BWR type BB fixed with screw/ nails to timber frame of 9 mm thick for ceiling complete all as specified and directed.

S& F Plain fillet, square, rectangular or triangular in section, clean sawn exc 16Sqcm sand not exc 25 Sqcm secured with nails complete all as specified and directed.

S&F pre painted galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550MPa as in roof covering/cladding to wall, fixed with self-tapping screw including necessary scaffolding, any type, any location/height complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws including necessary scaffolding, any type, any location/ height complete all as specified and directed.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) Fe -410-W(gde-E-250) Quality A including distance pieces, cleats etc complete all as specified and directed.

M & L for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and complete all as specified and directed.

M&L for second class soft wood 35 mm Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S & F Mild Steel butt hinges 75mm long medium weight complete all as specified and directed.

S & F 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F Mild steel pressed handles, 150mm oval type, stove enamelled black complete all as specified and directed.

S & F Mild steel pressed handles,100 mm oval type, stove enamelled black complete all as specified and directed.

S&F Sheet glass, ordinary quality 4mm thick plain and glazing with oil putty/ wooden beading in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, in soft/loose soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) in foundations filling and mass concrete complete all as specified and directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 including one shop coat of zink chromate primer paint including preparation of surface complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for two coat of cement base paint over a coat of Alkali resistant primer to newly plastered surfaces of wall incl preparation of surface complete all as specified and directed.

M & L for RCC design mix M-25 (20 mm graded aggregate use) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like (tank slab) complete all as specified and directed.

M & L for use and formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping for rough finished surfaces of concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 in kerb or mud stops rounded or chamfered on edges all as specified (20mm graded aggregate) for copping, including weathering slightly rounded or chamfered using form work (Straight or curved) complete all as specified and directed.

M& L for 100mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified and directed.

M&L for 30 mm thick sand cushion under paving block including watering and consolidation for ILCB complete all as specified and directed.

M&L for 100 MM thick factory made coloured inter locking cement concrete tiles with Grade of M-50 conforming to IS 15658-2006 manufactured by hydraulic pressure process, with grey cement and pigment laid over sand complete all as specified and directed. Note:- Tiles shall be approved by GE in writing before incorporation in work . (Sand for cushioning shall be measured & paid Separately).

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection surfaces finished even and fair, complete all as specified and as directed.

Supply and fix Voltage stabilizer for automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 250 KVA including oil and dehydration, testing of stabiliser after installation complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to galvanized earth lead GI strip 25x4mm by means of bolts, nuts, check nuts and washer of galvanized iron or steel besides welding at all joints as shown in drawing and including excavation and earth work, GI pipe medium grade 40 mm bore for protection of GI strip and connected to continuous earth lead on pole/test point supply and laying charcoal dust common salt PCC 1:2:4 type B-1, chamber and MS angle iron frame 40x40x 3mm and RCC cover 40 mm thick(1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 6 mm dia round bars @ 75 mm c/c both ways with MS handle 12 mm dia PGI funnel and wire mesh for 20 mm dia GI pipe medium grade for watering all as shown in electrical plate No-3 on srl page No 497 of SSR Part I (2009) drawing and connection to earth test point incl testing complete all as specified and directed. Note:- The cost of earth lead/strip and GI pipe for protection of earth lead/strip up to 7.5 M is included in the quoted rate.

Supply, Laying, commissioning and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, laid in trenches, passing through pipes, fixed on walls complete including connecting properly by means of thimbles of sizes 150 Sqm 3.5 core complete all as specified and directed..

Excavation in trenches beyond 1.5m wide and n. exc 3 m deep for foundation for poles/stay etc including getting out in any type of soil complete all as specified and directed

M&L for sand cushioning to underground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified. Note:- Punned thickness shall me measured and paid.

M&L for Brick covering with equal to length of brick as mechanical protection to cable with well burnt sub class 'B' bricks laid complete all as specified and directed.

M & L for cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in pole coping and stay assembly complete all as specified and directed.

Supply, installing, testing and commissioning, factory made and tested (prototype having been CPRI type test certified), LT Panel, platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber with insulated copper bus bars suitable Amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, IP 65 class protection and made of 2 mm CRCA MS sheet and 40x40x6mm thick angle iron frame work, externally powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement (including provision of 65mm Godrej (Freedom) lock with 2 keys, internal wiring 2.5 Sqmm with PVC insulated, solid copper conductor, FR-LS-H cables, IS-694 marked of adequate size incl the provision of space to accommodate the under mentioned items. The scope of work includes the following:-

(a) Incoming

(i) MCCB 4 pole, 415 volts AC grade, 500 Amps rating and 40 KA rupturing capacity complete with microprocessor-based OL protection - 01 No

(iv) Indicating lamps: ­ 01 set of three

(b) Outgoing

(i) MCCB 4 pole, 415 volts AC grade, 250 Amps rating and 30 KA rupturing capacity complete with microprocessor-based OL protection - 03 No

(ii) MCCB 4 pole, 415 volts AC grade, 250 Amps rating and 20 KA rupturing capacity complete with microprocessor-based OL protection - 01 No

(i) All out going feeders shall be connected by cable through suitable size gland plate / glands.

(ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint.

Supply and erect steel tubular swaged poles ISI marked complete with cast iron base plate, final taper plug, bolts, nuts and screw drilling of holes for continuous GI earth wire as specified type 410-SP-55 (11 mtrs long) including applying two coats of aluminium paint over one coat of red oxide zinc chrome primer after preparation of surfaces complete all as specified and directed. (Note: Excavation and PCC shall be measured and paid separately).

Supply and Fixing mild steel Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed.

M&L for point wiring for one light point/Ex/fan point controlled by one switch with 1.5 sqmm PVC FR-LS-H insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead in and including cable 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified and directed..

M&L for LED Batten 1x20 W for regal batten for LED Universal batten for G 13 T with 18 W tube rods and Ultra bright LED Polycarbonate tube light very high efficiency suited for installation in existing T8 and connecting electrically using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core complete all as specified and directed.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply & fixing Switch piano type flush 6 Amp Single pole one way (ISI Marked) complete all as specified and directed.

Supply & Fixing ceiling rose surface Bakelite 65x50mm two to three terminals (ISI marked) complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 04 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, conf to Cat Pt No 6077 11 of Legrand or equivalent of make Hager/Merlin Garin fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply and fixing MCB SPN 06 to 32 AMP Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathed of PVC tape overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire, one twin core cable of size 10 Sqmm complete all as specified and directed.

S&F house service bracket (hook type) complete with 3.0m long G.I. pipe 40mm dia medium grade, two Nos 900mm M.S. hook and stay or guy complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3cm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanised iron wire 4.0mm dia by means of bolts, nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test all as specified or indicated including testing on completion complete all as specified and directed.

M/S ABDUL AZIZ MIR

M/S AB AHAD RATHER

M/S MUNEER AHMAD WANI CONSTRUCTIONS

M/S AK CONSTRUCTION