PROVN OF OFFICE SHED AND BARREL STORAGE SHED 264 COY, ONE TOILET FOR GENTS WOMAN AND SPECIAL REPAIR OF BLDG NO. P139 AT SCE PRAYAGRAJ

Amount

Excavation in trenches n.exceeding 1.50m wide and n.exc 1.50m depth for foundation etc or for shafts, walls, cess-pits, manholes, pier holes, cable etc n.exc. 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in including spreading, levelling watering and well ramming in layers not exc. 25cm thick complete all as specified and directed.

Removing excavated materials n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified & directed.

M&L for cement concrete 1:4:8, type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for cement concrete type B-1 (20 mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings, lneelers, aprx stones, bed plate, kerbs and likes slightly rounded or chamfered complete all as specified and directed.

M & L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed..

S & F steel work in tubular trusses, purlins, rafter, column where connected common rafter and running rails fixed with angle cleat or other common plates including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 complete all as specified and directed.

S&F rolled mild steel conforming to Gde Fe 290 (Gde E-165) (Plain or chequred) , joist, channel, angle or tee sections, fixed independently, without connecting plates, etc complete all as specified and directed.

M&L for MS screw bolts 11 to 15 mm dia (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut exceeding 15 cm and not exceeding 22.5 cm long complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 60 mm thick machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of M-35 grade with grey cement and pigment & laid over and including 30 mm thick sand cushion and joints filled with sand complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete with necessary form work complete all as specified and directed. Note:- Reinforcement & formwork to be measured & paid separately under respective item.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts with necessary form work complete all as specified and directed. Note:- Reinforcement & formwork to be measured & paid separately under respective item.

M& L for Reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates in chajjas complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in slabs supported on walls, roof beams etc and the like with necessary form work complete all as specified and directed. Note:- Reinforcement & formwork to be measured & paid separately under respective item.

Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for rough finished flat surfaces of concrete complete all as specified and directed.

Form work to sides of square or rectangular columns, pillars, posts and struts for rough finished surfaces of concrete complete all as specified and directed.

Form work to side & soffits of floor or roof beams , beam, shelves including supports, overhang etc rough finished complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for rough finished flat surfaces of concrete complete all as specified and directed.

M&L Damp proof course 40mm thick in cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate to horizontal or vertical surfaces including necessary form work complete all as specified and directed.

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 Kg per square metre and blinding with clean dry sand @ 0.05 Cum per Sqm complete. all as specified and directed.

M&L for polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 Kg per Sqm complete. all as specified and directed.

M&L TMT bar 10 mm dia and over, cut to length, bent to shape required ,including cranking ,bending spirally for hooping for columns, hooking end and binding with and including mild steel wire and annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel TMT bars 5 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping as in stirrups for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M & L Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and fair complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over & including 3 mm thick birla wall care putty complete all as specified and directed.

M&L for preparation of newly plaster surface of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of newly plaster surface of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 5489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including one coat of 3mm birla wall care putty complete all as specified and directed.

M&L for hardcore of gauge n exc. 63 mm, of broken stone deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C1 using 20 mm graded stone aggregate in plinth protection finished even and fair including necessary form work and cutting of joints using extra cement etc complete all as specified.

S&F providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Note:- (i) Net Opening will be measured lor payment purpose. (ii) Area not exceeding 2.00 sqm each complete as per manufacturer's specification and directed.

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS;1868 with minimum anodised coating of grade AC15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified and directed.

S&F 4.8 mm thick plain/pin headed glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M&L non skid, ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 and n.exc 0.38 Sqm in floor set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L non skid, ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 and n.exc 0.38 Sqm in vertical surface set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

S&F stainless steel tubing of 25 mm dia for curtain rod of wall thickness not less than 1 mm, fancy type with both side decorative brackets including end cap (wall to wall or flush to wall) for securing to curtain rod complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other Frames/ Chowkhat of size 65 X 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. (Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately)

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including cement mortar bedding (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations compete all as specified and as directed.

M&L for stainless steel butt hinge with steel pin medium weight of size 100 mm complete all as specified & directed.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long complete all as specified & directed.

S&F 150mm long aluminium bow handle cast type anodized fixed with steel screw complete all as specified and directed

S&F 300mm long, aluminium alloy, anodised aldrop door bolt including fixing clips of sheet, cast or extruded section and fixing bolts and 16mm dia bolt of sliding bolts of extruded sections complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 uding 12.5mm graded stone aggregate as in roof padding, roof kerbs, benching on roof slab and other similar works laid as per slop required finished even and fair complete all as specified and directed.

M&L for 10mm thick plaster in CM 1:3, mixed with liquid water proofing compound over concrete surface of roof when concrete is green complete all as specified and directed. Note:- Liquid water proofing compound shall be measured & paid separately under respective item.

Cleaning the dust, dirt and any other foreign material from roof surface and applying a coat of bituminous primer @ 0.40 ltr / Sqm uniformly and primer shall be allowed to dry over night as conforming to IS 3384-1986 complete all as specified and directed.

M&L for Laying of minimum 3mm thick APP membrane of (reinforced with non-woven fabric polyester type wt not less than 150 gms/Sqm) & minimum weighing 3kg/Sqm shall be done using butane torch maintaining 100mm side overlap and 150mm end overlap, sealing all overlaps and bonded to the surface by fusing and bonding torch on method complete all as specified and directed. Note: All water proofing work shall be done as per manufacturer instruction and under supervision of manufacturer technical representative.

Supply only Liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L for 40mm thick brick tiles laid over and including 15mm thick screed bed in CM 1:4 mixed with polymer based liquid water proofing additive @ 5 % by weight of cement or as per manufacturer's instruction and the joints of tiles shall be filled with CM 1:3 mixed with crude oil as per SSR-2009 (Part-I) on non assessable roof area complete all as specified and directed.

Spreading and leveling excavated approved soil in layers not exceeding 25cm thick including watering and well ramming including watering as required for filling under floor complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on ceiling surfaces of RCC or brick complete all as specified and directed.

M&L for preparation of new surface of wall and applying three coat of white wash on wall complete all specified and as directed.

M&L non skid, ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 and n.exc 0.38 Sqm in floor set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured wall tiles in vertical surface 450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in 1:4 CM complete all as specified.

S&F factory made solid PVC door frame of size 50 mm x 95 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and directed.

S&F factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick with partical board core (stile:) with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC Sheet polyyurathene painted on the front Face & 2 mm prelam PVC sheet on back face & fixing in frame at site complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified & directed.

M&L for 4mm thick sheet glass Figured glass, pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified & directed.

S&F for vitreous china wash and basin thin rim table top basin of size 415x415x145mm shape round complete all as specified and directed. Make :Jaquor Cat part OPS-WHT-15905 or equivalent make as specified in P.S.

S&F for waste coupling 32mm size full thread with 130mm height complete all as specified and directed. Make :Jaquor Cat part ALD-CHR-705L130 or equivalent make as specified in P.S.

S&F for bottle trap (with internal partition ) 32mm size with 300 mm & 190 mm long wall connection pipes & wall flanges complete all as specified and directed. Make :Jaquor Cat part ALD-CHR-769L300X190 or equivalent make as specified in P.S.

S&F two way angle cock with wall flange complete all as specified and directed. Make : Jaquar Cat part KUP-CHR-35041PM or equivalent make as specified in PS.

S&F for toilet paper holder with flap complete all as specified and directed. Make : Jaquar Cat part AQN-CHR-7753 or equivalent make as specified in PS.

S & F vitreous China white wash down water closet pan 250x585x415mm wall hung including fixing bolts,UF soft close seat cover, hinging device complete all as specified and directed. Make : Jaquor Cat part OPS-WHT-15951UF or equivalent make as specified in P.S.

S&F for single piece slim concealed cistern with floor mounting frame installation kit & S-type drain pipe connection set for wall hung WC ( with flush control stainless steel plate and frame complete all as specified and directed. Make : Jaquor Cat part JCS-WHT-2400FS or equivalent make as specified in P.S.

S&F for flush control opal complete all as specified and directed. Make : Jaquor Cat part JCP-CHR- 152415 or equivalent make as specified in P.S.

S&F for single lever tail boy with 150 mm extension body fixed spout with popup waste system with 600 mm long braided hoses complete all as specified and directed. Make : Jaquor Cat part OPP-CHR-15005BPM or equivalent make as specified in P.S.

S&F for angular stop cock with wall flange complete all as specified and directed. Make : Jaquor Cat part OPP-CHR-150053PM or equivalent make as specified in P.S.

S&F for soap dispenser with glass bottle complete all as specified and directed. Make : Jaquor Cat part ACN-CHR-1135N or equivalent make as specified in P.S.

S&F for corner glass self with bracket complete all as specified and directed. Make : Jaquor Cat part ACN-CHR-1173 or equivalent make as specified in P.S.

S&F rotational moulded, multilayer three layer white colour HDPE water storage tank of 500 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed.

S&F in repairs Ball Valves 20mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Minimum weight 20mm-210gms) as fixed in repair complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15mm bore with all fittings, fixed to walls and ceiling or laid in floors & complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20 mm bore gun metal, globe or gate valves, with iron wheel heads, screwed both ends for iron pipes and fixed complete all as specified and directed.

S & F PVC connection 15mm bore 60cm long with brass union at each end complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to wall or laid in trench or in floor complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to wall or laid in trench or in floor complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S & F PVC (SWR) floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75 mm bore complete all as specified and directed.

S & F 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F of salt glazed stone ware gully trap 180 x 150 mm, setting and jointing with solvent cement complete all as specified and directed

M&L for 150 mm dia bore salt glazed stone ware drain pipe grade 'A' conforming to IS 651-1972 laid in trenches and jointed in CM 1:1 complete all as specified and directed

M&L for cement concrete bed to drain pipe 100 mm dia including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type D2 using 40mm graded stone aggregate complete all as specified and directed.

Cutting holes into existing manhole brick wall manhole built in CM, connection new drains making good to pipes and rendering cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete (1:2:4) type B1 smooth finished and reforming benching as required for internal dia of pipe 150mm complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or above ground level unreinforced complete all as specified and directed. .

Dismantling of Stone slabs and tiles laid dry and dry or pointed of any description or thickness in floors, aprons etc complete all as specified and directed. .

M&L for 18 to 20 mm thick machine cut kota stone flooring ,laid & jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing finished laid over and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for grinding, rubbing and mirror polishing of kota stone complete all as specified and directed.

Taking down cement plaster on brick wall or stone wall etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed

M& L for Pressed steel frames 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified & directed.

M&L for Second class hardwood 35 mm thick factory made plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete al as specified and directed

S&F anodised aluminium snap grid frame work for false ceiling with size of grid 605 x 605 mm consisting of main and cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg per RM and 23.5 x 26.4x 1.4 mm weighing 0.191 Kg per RM respectively complete all as specified & directed.

S& F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified all as specified

S&F in repair 16 mm thick board acoustical tegular 600 mm X 600 mm in size fixed in joint less finish with jointing compound and jointing tape as per manufacturer instruction complete all as specified all as specified

M&L for preparation of new plastered surfaces, applying white cement based wall care putty(Birla/JK white) on the surfaces with minimum 1 to 2 mm uniform thickness making surface absolutely smooth by grinding with sand paper and applying two coats of oil emulsion distemper over a coat alkali resistant primer of approved shade on new surface of wall complete all as specified and directed.

M&L for complete removal of the old treated surfaces of wall including cornices etc.by scrapping with metal plate, wire brush etc & apply white cement based wall care putty(Birla/JK white) on the surfaces with minimum 1 to 2 mm uniform thickness making surface absolutely smooth by grinding with sand paper and applying two coats of oil emulsion distemper over a coat alkali resistant primer of approved shade on new surface of wall complete all as specified and directed.

M&L for preparing of newly plastered wall surface and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for complete removal of the old treated surfaces of wall including cornices etc.by scrapping with metal plate, wire brush etc and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Taking down door chowkhat with shutter area n-exc 1.5 Sqm each(without taking off shutters from the frame) complete all as specified & directed.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutters from the frame) complete all as specified & directed.

S&F MS framed work as in doors frame, doors or gates of angle iron, door frame or other section with gusset plate, rails, braces etc complete, drilled for fixing of steel sheeting or other covering etc. to prepared for hanging or sliding with including either hooks and hinges, also fastening and fixing and similar work confirming to Fe 290 Gde-E-165 complete all as specified.

Demolition of plain cement concrete in any position including tar felt & cement mortar bedding etc from roof or sunken complete all as specified and directed.

Complete removal of mud phuska from roofs of any thickness and removing the waste material from site to a distance exc. 250m but not exc. 500m and deposited where directed including cleaning of surface complete all as specified and directed.

Dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

All as per item No 53 but except tiles. Note:- Tiles obtained from dismantling shall be used.

S&F framed work such as in grills, grating ,hold fast of door and window chowkat etc., with ends of bars shouldered and or riveted or forget into spikes, frames guard bars, barred iron doors, and similar work conforming toFe 290 Gde-E-165 complete all as specified and directed

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F butt hinges extruded aluminium alloy with galvanised mild steel pin type B-21 of size 100mm including welding etc complete all as specified and directed.

S&F 150 mm size extruded aluminum alloy handle, fabricated type, anodised, fixed with screws complete all as specified and directed.

S&F 200mm long aluminum anodized barrel tower bolt of extruded section, fixed with screws complete all as specified and directed.

S& f in repair 300mm long aluminium alloy anodised sliding door bolts, with hasp staple ( bolt type) and fixing clips of sheet cast or extruded or cast aluminium alloy complete all as specified & directed.

S&F 300mm, MS ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in bed blocks for hold fast including necessary form work complete all as specified & directed.

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing capping/concealed etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing surface & taking down old light fitting and fixtures complete all as specified & directed. Note:- Contractors quoted their rate of this item deemed inclusive of unscrewing of the serviceable fitting and fixtures shall be contractor's property as per Sch of credit. (ii) Quoted rate also deemed to include cost of cutting chases for taking out concealed conduit and nitch for terminal boxes etc.

M&L for point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FR PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bend, junction box and modular metal flush sunken box 60 mm deep & 1.6 mm thick duly painted inside and anticorrosive out side for mounting switches, sockets, fan regulators etc with modular white cover plate with frame of suitable size, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar (1:4) and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/Exhaust fan/ bell point etc complete all as specified and directed. Note : (a) Switch/bell push/fan regulator etc will be measured and paid separately (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surfaces. (c) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amp same board.

One point for socket outlet 5 amps on independent board

All as per srl item No. 121 above but for one 3 pin socket outlet 15 amps, independent, with cables 4.0 sqmm size on independent board 4.0 Sqmm earth wire complete all as specified and directed.

S&F ceiling rose surface type bakelite 65x50mm three terminal complete all as specified and directed.

S&F angle/batten type holder insulated body with back plate suitable for light point complete all as specified and directed.

S&F modular Switch piano single pole one way 6 amps complete all as specified & directed.

S&F modular Socket out let 2 in one, 5/3 pin 6 Amp flush type 2 module complete all as specified & directed

S&F modular switch, 16 Amps flush type single pole one way complete all as specified & directed.

S&F modular socket outlet 2 in 1, 3 pin, 2 module 5 &16 Amps flush type complete all as specified & directed.

S&F modular fan regulator, electronic type, 5 stepped, 120 watt, flush type , single phase 230 volt including connection complete all as specified & directed.

M&L for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 6 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 6.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

S&F in replacement sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' curve, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB SPN 40/63 Amps 'C' curve breaking capacity 10 KA of rating & making connection complete all as specified & directed.

S &F LED tube light fittings with decorative ultra slim linear LED light fitting fixture 20 watt with co extruded polycarbonate body environmental friendly, Energy efficient tube light complete with all associates internally prewired & including LED lamp 20 watt 01 no. and connecting up with 2 core flexible copper conductor cable with suitable size complete all as specified & directed.

Supply & fixing ceiling fans complete with blades ,down rods , electronic regulator and accessories ,230V ,1200mm sweep .min air delivery 210 CFM with service valve 6.00 BEE .five star rated with brushless direct current ( BLDC) including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan including testing on completion complete all as specified and directed.

S & F VTPN DB 4 way DPX³ 100A MCCB Double door DB's as per IEC 61439-3, suitable for flush mounting and surface mounting with 250 Amp copper busbar for each phase with 2 Neutral bar, 2 earth bar and cable ties for cable management, fully insulated busbar & shrouded neutral bars, improved pan assembly for ease of installation, prefitted masking sheet, reversible door for IP 43 & IP 54 DB's with provision for DPX³ 100 MCCB as incomer and SP/TP MCB's as outgoing with metal door complete all as specified and directed.

S & F in repair MCCB 100 Amps, 415 Volts, 4 Pole, breaking capacity 16 KA, ISI marked, adjustable type complete all as specified & directed.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type B-0 using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified and directed. Note:- PCC pit shall be provided at least 500 mm away the earth pit and not just on the earth pit and extra cost of additional length of water pipes & fittings junction etc shall be deemed to be included in the quoted rate. (ii) Item includes the cost of 7.5 mtr earth lead wire and G.I. pipe for protection of earth wire are also included in the quoted rate.

Supply and fixing LED building security street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection bracket for street light made out of 40 mm bore GI pipe medium grade not less than 1.2 mtr length bent at 120 degree to shape fixed on pole/wall with and including 50x6mm FI clamps = 02 Nos with nut bolts, washers including painting of clamps with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for sand cushioning with Ganga Sand to underground cable (8 cm thick before laying and 15 cm thick after laying the cable complete all as specified & directed. Note:- Punned thickness of sand shall be measured for payment.

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete all as specified and directed.

Supply & laying of XLPE cable of size 25 Sqmm 3.5 core Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor using lugs both end of cable& wrapping pvc tape over XLPE insulation cable and testing complete all as specified & directed. Note :- Excavation & earth work, sand cushioning, bricks protection where required shall be measured & paid separately)

M&L for 40 mm bore GI tubing 'light grade' with all necessary fittings laid in trenches/under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete all as specified & directed.

M&L for boring under road horizontally of size 50 mm bore using GI pipe for passing of cable in road/path in hard/soft/ loose soil complete all as specified and directed.

S&F switch piano, flush type 5 amps, single pole, one way 230 volt complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5/6 amp flush type complete all as specified & directed.

S&F in replacement sheet metal enclosure for MCB's 240 volt 4 way single pole and neutral with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB SPN 32/40 Amps 'C' curve breaking capacity 10 KA of rating & making connection complete all as specified & directed.

M&L for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 4 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

S & F LED light fitting 10 watt mirror type with high output with opal diffuser 2 ft 230 V AC with driver holder and LED lamp including making connection with three core PVC flexible insulated, sheathed copper conductor cable complete all as specified and directed.

S&F LED with 10 W bulk head fitting with high output with opal diffuser 230 V AC decorative type with driver holder and LED lamp including connecting with three core flexible copper conductor cable of suitable size complete all as specified.

S&F Exhaust fan, steel body AC single Phase. 230V of size 300 mm single phase 230 V AC , 1200 RPM Range complete with frame & louvers shutter including making hole & grouting in wall , mounting frame with nut, bolts, washers, fasteners , etc and connecting exhaust fan to ceiling rose including provision of three core flexible copper cable of size 1.5 sqmm not less than 0.5 mtr long for connection & testing including writing MES No complete all as specified & directed.

Supply & laying of XLPE cable of size 10 Sqmm 2 core Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor using lugs both end of cable& wrapping pvc tape over XLPE insulation cable and testing complete all as specified & directed. Note :- Excavation & earth work, sand cushioning, bricks protection where required shall be measured & paid separately)

Supply & laying of XLPE cable of size 35 Sqmm 3.5 core Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor using lugs both end of cable& wrapping pvc tape over XLPE insulation cable and testing complete all as specified & directed. Note :- Excavation & earth work, sand cushioning, bricks protection where required shall be measured & paid separately)

M&L for 50 mm bore GI tubing 'light grade' with all necessary fittings laid in trenches/under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete all as specified & directed.

Taking down carefully submain wiring of any number of wire and size with earth wire on wooden batten / surface conduit/ casing caping complete with its all accessories complete all as specified and directed.

S&F DLP UPVC trunking compartment of 150 X 50 mm size with all accessories with cover clip on separates partition left right top internal angle, flat angle, raise function cover to body joints mosaic clip & support from mosaic isolation bracket 2 mm thick complete all as specified and directed.

S&F Lamp holder, PVC/ polycarbonate type with back plate suitable for batten fitting complete all as specified & directed.

S&F modular Switch piano flush type single pole one way 5 amps complete all as specified & directed.

S&F modular Socket out let 2 in one, 5/3 pin 5 Amp complete all as specified & directed

S&F modular Switch piano flush type single pole one way 15 amps complete all as specified & directed.

S&F modular socket 6 pin, 3 module 5/15 Amps flush type universal complete all as specified & directed.

S&F fan regulator, modular type, 5 stepped, 120 W, single phase 230 volt including connection complete all as specified & directed.

S&F in replacement sheet metal enclosure for MCB's 240 volt 6 way single pole and neutral with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F in replacement of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver with suitable size of wire complete including connecting with three core flexible copper conductor cable of suitable size complete all as specified by Engr-in-charge

M&L for taking down deposit to MES store yard & painting of ceiling fan complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc make it serviceable by repair / rewinding and hanging the same on hook and GI pipe as required etc complete all as specified and directed.

M&L in replacement modular single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps 240 volt capacity including taking down complete all as specified & directed.

Schedule of Credit (MINUS) Rs. 22515.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

Channa Brothers and Co. (BID ID -3132918)

M/S Garg Sons (BID ID -3123677)