ADDNITION/ALTERATION OF TOILET BLOCK OF BLDG NO.T-92 OF HQ CIF(R) AT PALMA GRN UNDER AGE (I) CIF (R)

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S & F rolled mild steel work in tubular trusses, vertical posts, rafters, purlins etc. including special shaped etc complete using ERW or induction butt welded tubes conforming to Gde St-240 and painted one shop coat of zinc chromate primer paint (including preparation of surface) at contractor's workshop before fabrication complete all as specified and directed.

S & F mild steel work as in wind ties for roof including all necessary drilling, bolting or riveting, etc.,and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

Preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel painting over a coat of red oxide primer complete all as specified and as directed by Engr-in-charge.

Dismantling wall and ceiling boards, fibre pulp insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

S&F AC designer composite ceiling board 4-6mm thick in 600x600mm panel confirming to IS-14682 TYPE-B category-3 including GI frame, holdfast and suspenders complete all as specified and as directed by Engr-in-charge

Cutting holes exceeding 150 sq.cm but nexc 400 sq.cm in to brick walls built in CM and making good in cement concrete 1:2:4 type B1 for fixing of cooler Brackets etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor, paving not exc. 15 cm thickness (below or above ground level) complete all as specified and directed

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

M&L 75 mm thick cement concrete (1:4:8) type D2 as sub base to floor as complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for 10 mm thick rendering as backing coat to receive the tiles on fair faces of brick /concrete surfaces in cement mortar 1:3 and finished even and rough complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles (square/rectangular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface,complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 300 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:3:6 type C 2 (40 mm graded aggregate ) as in plinth protection, finished even and smooth without using extra cement complete all as specified and directed

S&F powder coated aluminium window side hung aluminium window/ ventilator frame or chowkats 1.5 mm thick aluminium anodized of size 65 mm x 40 mm and window shutter frames (sides rail, top rail, bottom rail and middle rail) 1.5 mm thick aluminium anodized of size 45 mm x 45 mm including all fitting such as rubber gasket aluminium glazing clips, locking arrangement and 75 mm aluminium handle and including 5mm thick tinted plain glass in panels fixed with rubber, gasket and aluminium beads, aluminium tower bolt 100 mm, aluminium butt hinges 75 mm 02 No in each shutter, complete all as specified and directed by Engineer-in-charge (Size of window shall be as sper site requirement.)

S&F powder coated aluminium frame and grill for door, window,ventilators with one or more rebated incl jointing cleat for fixing etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), complete all as specified and directed by Engineer-in-Charge.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube and fixed in opening as per specification and drawing complete all as specified and directed.

30 mm thick, factory made solid panel PVC moulded door shutter (style) consisting of frame made out of M.S tube for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rails and bottom rail on either side & as gap insert for top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, fixed in the frame at site as per specification and drawing complete all as specified and directed.

S&F aluminum handles cast type, anodised, 150 mm sizecomplete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and directed.

S&F stainless steel cold rolled butt hinges medium weight 100 mm long complete all as specified and directed.

M & L for Providing cement concrete Type D-2, 1:4:8 (40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

Brick work with Sub Class ‘B’ burnt bricks (Old size bricks) straight or curved on plan exceeding 6 m mean radius complete built in cement mortar 1:6. complete all as specified and directed.

M&L half brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stoneswork and precast concrete articles complete all as specified and directed

M&L for 10 mm thick on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick/concrete or stone surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete with water proofing compound complete all as specified and directed. (WPC shall be measured separtely).

Supply only integral water proofing complete all as specified and directed.

M&L for preparation of new plastered surfaces on walls and applying three coats of white wash.complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of cement based paint white or tinted over a coat of chalk whitening primer complete all as specified and as directed by Engr-in-charge.

M&L Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

S&F for steel water tubing of nominal bore dia 15 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and directed.

S&F for steel water tubing of nominal bore dia 20 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store/yard complete of bore 15 mm complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store/yard complete of bore 20 mm complete all as specified and directed.

S&F for 20mm dia, Ball brass, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified and directed.

S&F 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified and directed.

S&F for 1000 ltrs capacity rotational moulded polythylene water storage tank (Cylindrical vertical with closed top and triple layer with white colour) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F snow white one piece EWC Model Name: CASINO 660X350X760 S trap 220mm with soft colse seat cover, including fixing with screw/bolts complete all as specified and directed.

S/F in repair of hand health faucet complete all as specified and as directed.

S&F SS tubular towel rail, 20mm dia, D type, 60cm long between flanges , fixed with rawl plugs. complete all as specified in repairs. (ISI Mark)

S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

PVC connection 15 mm size with PTMT nuts of length 600 mm in repair complete all as specified and directed.

S&F for two way Angle valve, cast copper alloy fancy type screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and directed.

Stop valves/angle valve of 15 mm bore, but fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions including necessary fitting as required at site as in repair complete all as specified and directed by Engr-in-Charge.

S&F, 15 mm dia bib tap fancy type chomium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair, complete all as specified and directed.

32 mm dia waste coupling fittings brass chromium plated for glazed ware sink, basins etc with long screwed shank and fly nuts, flanges end bedded in red lead cement and other end fixed in repair complete all as specified and directed.

Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F SS grating 100mm dia fixed to floor trap in repair complete all as specified and directed.

S&F in repair PVC waste Pipe 32/40mm dia and fixed complete all as specified and directed

Supply and fix in repair vitreous china wash hand basin white table top size 550x400mm excluding taps waste chain and plug and porcelain stopper but including brackets waste fitting brass chromium plated 32mm dia with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed etc complete all as specified and as directed by Engr-in-charge.

Brass CP wall/basin mixer for mixing hot & cold water screwed down for iron pipe and fixed in repair complete all as specified and directed.

Brass CP shower rose 125 mm size in repair complete all as specified and directed.

S&F for PVC (SWR) floor trap with dia of outlet 75mm with grating including jointing to waste pipe fixed in cement concrete PCC 1:2:4 type B-1 complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls complete all as specified and directed.

S&F 75 mm PVC (SWR) bends any radius complete all as specified and directed.

S& F 110 mm bore PVC SWR bends and fixed with joint sealent etc complete all specified and as directed

S&F stack clamps out of 50mm by 5mm flat iron and 6mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof 100mm bore of pipe complete all as specified and as directed.

S&F 110 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75 mm PVC (SWR) junction double, (double T), equal or unequal complete all as specified and directed.

S&F for PVC (SWR) reducers complete all as specified and directed.

S&F for 75 mm PVC (SWR) vent cowl complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5m in depth for foundations, etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

Removing excavated material(soil) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed

Returning, filling in any type of soil, including spreading, leveling , watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified.

M & L for PCC type C 2 1:3:6 (20mm graded stone aggregate) as in surface channels and drains etc incl.necessary form works complete all as specified and directed.

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stop ends etc complete all as speicified and directed by Engr-in-Charge

Demolition and breaking up 150mm dia SGSW/ PVC or reinforced conerete pipes set in cement mortar and taking out of trenches complete all as specified and directed.

S&F 150 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L concrete bed to drain pipe incl packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) for 150mm bore pipe complete all as specified and directed.

Demolition of cement concrete (reinforced) as in roof, floors (other than ground floor), beams, staircase, landing, chajjas and similar suspended work, complete all as specified and directed.

Providing Precast cement concrete 1:2:4 type B-1 (20mm graded aggregate ) as in manholes cover slab etc all as specified and directed by Engr-in-charge.

Providing cement concrete 1:2:4 type B0 in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles complete all as specified and directed.

M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M & L for Construction of Septic Tanks for 10 users conventional type LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc removing material for taking credit ( credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring for one light/fan point controlled by one switch concealed type with PVC insulated unsheathed copper cable FRLSH 1.5 sqmm multi stranded two single copper conductor in and including suitable size PVC conduit pipe complete with all accessories and with 1.5 sqmm PVC insulated copper cable FRLSH continous earth wire, re-recessed mounting pressed steel GI sheet box 2 mm thick suitable for modular switch/socket of adequate size including iner and outer white cover plate of modular complete all as specified and directed for light/Fan/exhaust/call bell points.

All as per item No. 2 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 2.5 Sqmm PVC insulated unsheathed continuous earth wire and connecting to common earth dolly complete all as specified and directed.

Supply and fixing of modular switch single pole one way 6 Amps 1 module complete all as specified and directed

Supply and fixing of modular switch single pole one way 16 Amps 1 module complete all as specified and directed

Supply and fixing of modular socket 6 A/16 amp -2/3 pin combined 2 module complete all as specified and directed.

Supply and fixing of ceiling rose 65X50 mm two to three terminals complete all as specified.

Supply and fixing MCB DB 8 way double door SPN, 240 Volts all as specified and directed.

Supply and fixing MCB SP 6 to 32 Amps 'B' curve, 240 Volts all as specified and directed.

Supply and fixing MCB SPN 6 to 32 Amps 'B' curve, 240 Volts all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sq mm 2 core. All as per specified and directed.

Supply and fix Exhaust Fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of Sweep 250 mm sweep inluding making fixing arrangements including cutting of wall/surface for fixing of exhaust fan and making good the disturbed surface shall be part of job at no extra cost complete all as specified and directed.

Supply and Fixing LED light fittings 1 x 20 Watt, 220 V, AC decorative box type with driver, holder including LED tubelight connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting with high out put diffuser 2 feet, 10 watt 220 Volt, AC decorative type with driver holder and LED lampincluding connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4.0 mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frame 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I. All as specified and directed.

Excavation in trenches, in any type of soil not exc 1.5 mtr wide and not exc 1.5 m in depth for foundation, etc or not exceeding 10sqm on plan and not exceeding 1.5m in depth for pole, shafts, cesspits, manholes, pier holes, etc. and getting out of any type of soil for laying UG cables of various sizes complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n. exc 25 cm in any type of soil complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Material and labour for well burnt bricks,Sub class 'B' bricks, best quality locally available laid flat, dry in trenches for cable protection complete all as specified and as directed

Material and labour for sand cushioning with fine dry unwashed sand in trenches for protection of cables complete all as specified and directed.

S&F in replacement of GI pipe light grade 40 mm complete for laying under PCC/bitumonus road or critical narrow trench, under floors and mechanical protection of UG cable complete all as specified and directed.

M&L for dismantling of existing serviceable geyser of any capacity and type. Refixing the same including fixing arrangements such as flexible connection pipes, fasteners etc. complete all as directed by Engr-in-Charge.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of 19,178.00 during AOC Note:- Tenderers shall not quote for this Schedule