Development of Eco park at Ooty in Nilgiris district, Tamilnadu(Package V)

Surface dressing of the ground including removing vegetation ind inequalities not exceeding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m All kinds of soil.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15cm thick well rammed with surface vibrator, watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying filling in foundation,basement etc with filling suitable embankment filler materilas in layers of not more than 15cm thick well watered,rammed and consolidated etc., complete complying with standard specification and as directed by the department officers.

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Providing and laying in position, standardised concrete Mix M-25 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglm³ and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3'3 cu'm') 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg' of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

Ground Floor

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Foundation and Basement

RCC Lintels

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

R.R Masonary in cement mortar1:5(one cement,and five crushed stone sand) for foundation and basement including simultaneously pointing above ground level with the same mortar directed by the departmental engineers etc., complete complying with standard specification.

Pointing with Cement Mortar 1:3 Flush pointing Random Rubble , etc., complete complying as per the standard specifications.

Precast Concrete Block masonry using Autoclaved Cellular Aerated Concrete Block of size 600x200x225mm conforming to IS 2185 (Part 3) : 1984 with Self Curing AAC Joint Mortar for Partition Wall of non load bearing type in accordance with IS 6041:1985 including neat finishing, etc., complete complying with standard specification and as directed by the departmental officers.

Precast Concrete Block masonry using Autoclaved Cellular Aerated Concrete Block of size 600x200x150mm conforming to IS 2185 (Part 3) : 1984 with Self Curing AAC Joint Mortar for Partition Wall of non load bearing type in accordance with IS 6041:1985 including neat finishing, etc., complete complying with standard specification and as directed by the departmental officers.

Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work).

Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat on cement plastered wall surface ect., complete complying with standard specification and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying, fabricating, and fixing in position cast iron railing of approved design and pattern, including all necessary fixtures, fastenings, nuts, bolts, welding, grinding, and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete as per drawing, specification, and direction of the Engineer-in-Charge.

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc.,

Supplying and fixing solid core flush shutter of following type with thickness with necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 6 Nos of SS 304 Grade Butt Hinges of size (125mm x 30mm) , 3 Nos. 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Double leaf. Type : Thickness:

Supply and fixing of FRP door Sutter with FRP door frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers.

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc -Manually Operated (up to 8 sqm. Area)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The ventilator should be got approved from the Executive Engineer before use on work

UPVC WindowSupplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Granite Stone Slabs of following size 1200 x 600 of 18 / 20 and Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Nosing for Granite Slab

Paving the floor with best quality vitrified Tiles of following size (double charged 600x600x8)mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with ceramic tiles of following size Plain ceramic 305x305x6 mm and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of following printed design colour glazed tiles of size 300 x 450 x 8mm in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and Painting using Enamel metal paint, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately).

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600mm x 600mm x 100mm in Cement Concrete 1:2:4 (One cement, Two sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBRValue-25

Providing and laying Water Bound Macadam Grading - II ( 75mm to 22.40mm) IRC HBG metal consisting of clean, crushed aggregates mechanincally interlocked by rolling and bonding together with screening binding material of 0.24 cum for 10 sqm (the material passing 425 microns sieve shall have liquid limit and plasticity index not more than 20 & 6% repectively) and finished in accordance with the requirements of the specification and thickness as per approved plans or as directed by the Engineer. (Mix -in - place method)

Supply and laying in position of dressed stone slab of 50mm thick Flammed of 450mmx 450mm over a sand bed of 100mm thick and Pointing the joints to full depth with Cement mortar 1:3 as directly by Departmental officers etc., complete compling with standard specifications.

Providing and laying heavy duty cobble stones 75mm thick interlock pavers, using cement and course sand for manufacture of blocks of approved size, shape and colour with a minimum compressive strength of 281 kg per m2 over 50mm thick sand bed ( average thickness ) and compacting with plate vibrator having 3 tons compaction force thereby forcing part of sand underneath to come up in between joints, final compaction of paver surface joints into its final level, including cost of materials, labour and Usage charges of machinery complete as per specifications.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density ( proctor density)

Providing and Laying good quality red earth filling, including cost & conveyance of red earth from approved sources to work site including labour for spreading, watering and compacting to achieve the required Proctor density at 100% compaction.

Supplying and errection of Retail shops/Cloak and Control Room as per drawing mentioned size which is made up of Kiln dried Pine wood Exterior wall of 105 mmthickness. Pine wood wall frame 75mmx38mm thickness 18mm thick pine wood as exterior cladding and 12 mm thick pine wood as internal cladding. Four Layer Roof in Pinewood with wall frame thickness of 100mmx38mm up on which 22 mm Pinewood covering and topped with water barrier sheet and Asphalt Shingles. Internal partition wall between room Polish to be done on Pinewood exposed areas of the colour approved by our engineer in-charge.

Supplying and errection of Toilet of size 11x4m which is made up of Kiln dried Pine wood Exterior wall of 105 mmthickness. Pine wood wall frame 75mmx38mm thickness 18mm thick pine wood as exterior cladding and 12 mm thick pine wood as internal cladding. Four Layer Roof in Pinewood with wall frame thickness of 100mmx38mm up on which 22 mm Pinewood covering and topped with water barrier sheet and Asphalt Shingles. Internal partition wall between room and toilet to be of 99 mm thickness comprising of 75 mm x 38 mm pinewood wall frame covered with 12mm cladding on room side and 12 mm cement fibre board on toilet side. Centre roof height as mentioned in the drawing and as directed by the engineer in-charge. Polish to be done on Pinewood exposed areas of the colour approved by our engineer in-charge.

Designing, supplying the Installing the New Sheffield Cycle Shelter Pre-fabricated sections for ease of installation using the principles of the Wardale design while incorporating curved front-end frames and omitting PET end panels for a cost-effective solution modular units that can be linked to accommodate varying quantities of cycles.all complete as per the direction of Engineer-in-charge

Supply and Fixing pf 1" Class Teak Wood Sports Flooring standards - finished with 21 mm thick, 55 to 85mm wide and in random length in tongue and groove shape. The edges of the boards will have a finger lock groove and the bottom side with air pass groove and treated with special anti-termite and water-resistant lacquer. THE UNDER FRAME: - Resilient SPF Pine Wood sleeper subfloor of 70 mm x 45 mm, treated with anti-termite solution and fixed on the bottom side with 19 mm thick EPDM rubber pads, stapled through the two wings at 350 mm x 350 mm.INSTALLATION: - 52mm thick CC subfloor treated with a vapor barrier to be placed on the levelled CC sub-floor before laying the under frame. The runners having air cushion pads to be placed on the vapor barrier in perfect level at 350 mm in 1 direction. The surface board to be Nail to the runner through the tongue only and will lock the screwed tongue by the groove of adjoining board. Ends of the boards will be locked by inserting the wooden fingers through the edge grooves and fixed with suitable adhesive. The expansion of 12-15 mm will be left open between the wooden flooring and the surrounding tiled area / walls. FINISHING: - After installation the floor will be machine sanded in uniform level and finished with P. U. Polishing water based polyurethane lacquer. Game line marking to be carried out in required colors before applying the finish coat

Providing, fabricating and fixing of stick type structural glazing using Alluminium Extrusions of 63.5 mm x 58.00 mmx 2.25 mm of 1.73 kgs/ mtr for vertical and Horizontal members and 63.5 mm x 38.1 x 1.33 mm of 0.759 kg/Mtr, as outer frame with Electro Anodized Paint coated block finishing, using 6mm thick imported glass reflective hard coatedocean blue raw glass with all necessary accesories like ultra glass Silicon sealant of Space tape, Masking tape, Galvanized Anchaor bolt, machine screws, 6mm thick M.S. angle 50mm x 150mm x 6mm M.S. Galvanized L Brackets, structural sealent setting clocks, fasteners, wall connection etc., complete

Supplying & fixing in position Greenlam Sturdo Classique Invincible Toilet Cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch impact and anti bacterial resistant 12mm thick solid compact laminate panels tested by shriram Test House. Finish of the compact laminate should be suede/ *Raw silk, which includes doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate. This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer’s specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U-Channels, (6) SS-Shoe Box Plate (7) MS-Base Plate, (8) Top rail with Corner conntector (9) Rubber noise deafening tape (10) Screws & wall Plugs. The top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the ss top rail.All screws will of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel Bottom Cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 110mm.Toilet Cubicle with standard dimension of 2100mm Height x 1000mm Width x 1550mm Depth, which includes 600mm door size width). Toilet Cubicle I-Shape (Front Partition) with standard dimension of 1885mm Height x 1000mm Width which includes 600mm door size width). The divider height to 2100mm height All aspects specified by the manufactures, Greenlam Sturdo Classique Invincible Model or equivalent. complete as per directions of Engineer-in - charge

Supply and installation of Perforated Glass Fiber Reinforced (GFR) Gypsum Concealed Acoustics false Ceilings, GFR gypsum panel, backlined with acoustical fleece, having random circular perforations of 8mm dia, 15mm dia and 20mm dia 5% open area having 4x14mm slotted perforations @ 10x20mm pitch, in H8 Pattern 15% open area size 1200x2400x12.5mm, square edge, volume density of base board 650 Kgs/m3, weight 8Kgs/m2 installed by using Strut ceiling framework. The Strut ceiling framework system shall include Strut WC25, fully knurled, sectional thickness 0.5mm, length 3600mm, unequal flanges of 20 & 30mm and web of 25mm, fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. Then suspend Strut MC45, fully knurled, sectional thickness 0.8mm, length 3600mm, equal flanges of 15mm and web 45mm from the soffit at 1200mm centers with Strut SA25, fully knurled, Suspender angle with sectional thickness 0.45mm, unequal flanges of 25 & 10mm such that free end of Strut MC45 rests on Strut WC25 along perimeter of wall. Extra support to be added near jointing of two MC45 so that end cantilever should not be more than 150mm. Strut CC25, fully knurled, sectional thickness 0.55mm, length 3600mm, web 50mm, depth of 25mm and equal flanges 15mm is fastened to the Strut MC45 perpendicularly at 600mm centers for upto RH70, at 400mm centers for RH70-RH90 and at 300mm centers for >RH90 and inserted inside the Strut WC25 at the perimeter Snazz Cosmos panel is installed on the Strut CC25 with suitable fasteners at 600/400/300mm centres. The longer edges of panels should be perpendicular to length of Strut CC25. All edges should be chamfered for V-Groove 4mm gap should be maintained between adjacent boards on all sides and should be filled and finished with Seam AJC and tape Apply one coat of white primer with roller brush evenly across the board surface to achieve uniform colour. The system is backlined with the acoustical infill Synthetic polyfiber 5x50. TechParameters Fire (Class) -1 & P Acoustics - NRC upto 0.75 (For E600” Mounting) Climate (“C, RH)-50, 70 Light reflectance (%) - Paint dependent Green (VOC, RC %) -Low, 25 as directed by the department officers. The cost includes, cost of material, cost of labour, Scaffolding, Transportation, Conveyance Etc. omplete complying to standard specication.

Providing, supplying and fixing 25 mm thick Bison Panel (cement-bonded board as per IS 14276) on approved timber/GI frame, including cutting, fitting, screwing, jointing with compound and tape, applying primer and two coats of approved paint/finish, complete in all respects. All materials, framing, fasteners, and workmanship shall be as approved by the Engineer-in-Charge

Providing and fixing Signage board(300mmx750mm) fixed on the Stone masonry wall including drilling holes nuts and bolts and finishing works etc as per direction of architect and engineer in charge(The cost of stone masonry to be paid Seperatly)

Providing and fixing Signage board(600mmx2400mm) fixed on the Stone masonry wall including drilling holes nuts and bolts and finishing works etc as per direction of architect and engineer in charge(The cost of stone masonry to be paid Seperatly)

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of walls.Brick / Stone Masonry in cement mortar walls under 3m high

Supplying and errection of Cloak Room of size 3x4m which is made up of Kiln dried Pine wood Exterior wall of 105 mmthickness. Pine wood wall frame 75mmx38mm thickness 18mm thick pine wood as exterior cladding and 12 mm thick pine wood as internal cladding. Four Layer Roof in Pinewood with wall frame thickness of 100mmx38mm up on which 22 mm Pinewood covering and topped with water barrier sheet and Asphalt Shingles. Centre roof height as mentioned in the drawing and as directed by the engineer in-charge. Polish to be done on Pinewood exposed areas of the colour approved by our engineer in-charge.

Supplying,erecting and installing the food kiosk with 50mm x 50mm MS Structure with Commercial Ply cladding inside and outside with Laminate Inside and ACP Outside and Metal Rafters inside in the Center area for all side walls, Back walls and front wall. and with wooden flooring and celing with Metro sheet cladding outside and insulation with Glass wool and thermocoal. 18mm Commercial ply with Laminate on the top and granite at the top including the Sink and accessories Tap and Piping for back storage on the floor and also includes focus light and sticker names with electrical works including havells Switch & sockets at 10 Points. and also includes glass work and Branding Work . the rate includes all labour charges transportation charges and other charges for completion of work as per directions of engineer-in-charge of the work.

Renovation Works for Electrical Works

Supplying and fixing in position white/ colour special delux model glazed cascade type paryware/Hindware/Equivalent wall mounted European water closet of best quality and approved make with 100mm "P" or "S" trap connecting with CI pipe of 100mm dia/ PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing,spun yarn, teak wood plugs,brass screws, etc., including supplying and fixing 10 litres capacity PVC/12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball value with polythene float with brass handle, union cuppling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 nos), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover. Wall Fitting

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supply and fixing in position of White glazed porcelain Oval shape Spl type Urinal size 382 x 398 x 601mm of best quality and approved make of size 382 x 398 x 601mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying, fixing, testing and commissioning of approved make 15mm CP Concealed Stop cock with one no, CP flexible tube 1.0m long, CP crutch, nozzle etc., complete.

Supplying and fixing CP Two Way Bib Cock with Health Faucet of approved make.(Parry Trio) as per standard specifications.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying, fixing, testing and commissioning approved make Angle valve with necessary fittings.

Supplying and fixing in position UPVC specials / Pipe of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

40 mm dia

50 mm dia

Dia 40mm Elbow

Dia 50mm Elbow

Dia 40mm Bend

Dia 50mm Bend

Dia 40mm TEE

Dia 50mm TEE

Dia 50mm X 40 mm Reducer

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

75 mm dia

110 mm dia

160 mm dia

Dia 75 mm Elbow

Dia 110 mm Elbow

Dia 110 mm SHOE

Dia 75 mm Y

Dia 110 mm Y

Dia 75 mm Tee with Single Door

Dia 110 mm Tee with Single Door

Dia 75 mm Bend

Dia 110 mm Bend

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M Sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three M Sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) a) 110 x 75 mm dia (20 mm water seal)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110mm dia PVC Pipe

Dia 110 mm Elbow

110 mm dia

160 mm dia(soil pipe)

Supplying, fixing, testing and commissioning of glazed stoneware gully traps, 550x550mm C.I. grating (medium duty), 100 mm dia outlet set in PCC 1:4:8 bed, 115 thick masonry chamber in CM 1:4, internal and external plastering 12mm thick in CM 1:6, necessary earthwork, C.I. cover (medium duty) etc., complete.

Providing and constructing inspection chambers comprising burnt brick/solid block masonry walls of 230 mm thk., built in CM 1:4 over M-15 CC bed of thickness 100 mm, benching in CC M-15, internal faces plastered smooth in CM 1:4, 15mm thick and outside Rough Plastered with CM 1:6, 15mm thick including necessary earth work excavation returning and refilling and disposing surplus soil as directed by the Engineer in charge.

Inspection chamber of size 600 x 600 x 600mm

600 x 600 mm size internal and depth more than 450 mm but not exceeding 850 mm

600 x 600 mm size Heavy duty cover

HGS SS.20.B. Earth work excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders SS.20B

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

dia 20mm

dia 25mm

dia 32mm

Dia 20mm ELBOW

Dia 25mm ELBOW

Dia 32mm ELBOW

Dia 20mm TEE

Dia 25mm TEE

Dia 32mm TEE

Dia 20mm COUPLER

Dia 25mm COUPLER

Dia 32mm COUPLER

25 mm x 20 mm REDUCER

32 mm x 25 mm REDUCER

40 mm x 32 mm REDUCER

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

dia 40mm

Dia 40mm ELBOW

Dia 40mm COUPLER

Dia 40mm TEE

40 mm x 32 mm REDUCER

32 mm dia ( UG SUMP TO OH TANK)

Dia 32mm ELBOW

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

Dia 32mm

Dia 40mm

Providing and placing on terrace Polyethylene water storage Tanks as per IS 12701 : 1996 with manhole lid and suitable locking arrangements, making holes of suitable diameter for inlet, outlet and overflow pipes, including cost of all materials, labour transport charges, HOM and testing complete as per specifications.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with GI Flush Mounting box and 6A FT switch in flush with wall with Modular cover Plate (Plastic) and making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with suitable model MS box, modular cover plate and 6A FT switch and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & pumproom, etc.)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm, MS switch box with Modular coverplate along with 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point

Wiring with 2 x 2.5 sq.mm. (36 / 0.3) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm Metal switch box with face plate for 15A 3 pin non inter locking wall socket with 5/15A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed power plug point

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earthconnection (For Water pump)

Supply and fixing of single box type 4'18W LED Tubelight fitting complete with electronic ballast with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board of double door type with metal door with IP43 protection with 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (like standard make)

Supply and run of 2 of 2.5 sq.mm. (36 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable rigid PVC conduit pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and laying of 2 x 2.5 sq.mm. (36 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in 25mm dia GI pipe (Class 'B') with necessary accessories and end supports for water pump

Supply and run of 1 of No.8 SWG GI wire for earth connection, including cost of all materials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and insallation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

Supply and laying of 2 x 6 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and laying of 4 x 10 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of 5A or 10A or 20A AC single phase 230V, 50 Hz Watt hour metre on suitable TW box complete with earth connections

Supply and fixing of 10A 400V, 50 Hz 3 phase 4 wire watt hour meter on suitable TW box with earth connection

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End

Supply and fixing of WT bulk head fitting with guard suitable for with 7W/9W LED bulb.

Supply and fixing of single box type 4' 20W LED fitting with LED tube complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and Run of 3 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module Plastic surface mounting switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Lower End

Wiring with 2 x 4 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with suitable Module Plastic surface mounting switch box on wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 4 sq.mm copper wire for Open PVC pipe power Plug point ( 8 points / Coil) Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour.

Supply and Run of 3 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire with painting of suitable colour.

Supply and fixing of 1 no.6A two module 3 pin socket , 1 no. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Lower End

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm(12") sweep (lightduty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of 4Feet LED 18W Fitting with LED 18W tube (LowerEnd) complete with TW round blocks on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting

Supplying and fixing regular MCB distribution boards on wall/oodboard/flush mounting using required clamps,bolts,nutsetc.,with provision for fixing suitable type capacity MCB' ssingle phase/3phase/single door with powder coated painting Made out of 14SWG MS enclosure.II - Double Door 6 Way SP & N

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and'C'Typecurve, indicator ON/OFF,energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC60898. 6-32 A DP

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and'C'Typecurve, indicator ON/OFF,energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC60898. 6-32 A SP

Earthing as per PWD standard with an earth electrode of 2metre Class'B' GI pipe of dia not less than 32 mm complete with necessary masonry work

GST at 18%

Please Enable Macros to View BoQ information