1009/25.05.2026

Excavation for all types and sizes of foundation, trenches and drains or for any other purpos including disposal of excavated stuff upto 1.5 m lift and upto 50 m (at least 5m away from the excavated area), including dressing and leveling of pits.Page No.9,Item No.1.1(i)In all types of soil

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation,plinth and at ground level excluding cost of form work. 3.1.3 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size).

7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: 7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand)

Providing & making 15 mm thick cement plaster on the rough of side of single or half brick wall of mix: (iv) In Cement mortar 1:6 (1 Cement :6 fine sand)

Providing and filling in plinth with sand/Crusher dust and hard moorum under floor in layers not exceeding 20 Cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete. Page No.11, Item No.1.18

15mm thick Marble stone slab flooring over 18mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including grinding rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) Wonder marble.

Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work 1:1½:3(1:cement : 1½Coarse sand : 3graede stone aggregate 20mm nominal size)

Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete.

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. SS Grade 204

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 METER to 12 METER high GI octagonal pole including steel reinforcement (minimum 90kg per CUM), form work, embeding 2 nos 50mm dia PVC pipe for cable entry in EACH foundation, excavation disposal of surplus soil and curing etc. as required. TOP POST LANTERN (ELECTRICAL SOR ITEM NO.19.12/74)

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification. 75 mm outer dia and 60 mm Inner dia( for bollard top post) (ELECTRICAL SOR ITEM NO.14.1/52)

Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1). 3.5 x 25 sq. mm. (for Top post) (ELECTRICAL SOR ITEM NO.15.3/54)

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 4 X 10 sq. mm (22 mm) (EL.SOR. ITEM NO.-15.23.23/57)

Supply of GI PIPE POLE made of "B" class GI pipe making necessary hole for cable entry and providing earthing stud (welded at specified height) including painting with one coat of red oxide zinc chromate primer. 80 mm dia (for bollard & top post) (ELECTRICAL SOR ITEM NO.19.4/72)

Providing following size ISI marked FRLS PVC insulated , PVC sheathed, flexible copper conductor wire. 1.5 sq. mm three core (top post ) (ELECTRICAL SOR ITEM NO.32.2/147)

Supply of hot dipped galvanized (in single dip to minimum 75 micron) octogonal pole made of 3mm thick steel grade E-350 sheet having window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with following minimum specifications with 4 way terminal connector including 3mm thick anchor plate, 4 nos 16mm dia foundation bolts of EN8 grade, and as per IS 2062 & BS EN: 10025. (designed for wind speed upto 180km/hr, IS: 875 Part 3) 3 metre high, dia 130mm at bottom and 75mm at top, base plate size 200x200x12mm, foundation bolts 450mm long (top post) (ELECTRICAL SOR ITEM NO.19.6.1/73)

6.23 Supplying, installation, testing and commissioning of following 230/250 volts LED Post Top Lantern fitting with perplexcover/decorative diffuser, electronic ballast and all other accessories on existing gate column/pole bracket, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9 . LED chip efficacy ratio ≥ 100 lumens /watt. 6.23.1 25 Watt (ELECTRICAL SOR ITEM NO.36.23.1/16)

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification. Above 450 mm and upto 600 mm deep MAIN METAL BOARD, BBC, IC (ELECTRICAL SOR ITEM NO.7.19/34)

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification. 300 amp (50x5mm) (ELECTRICAL SOR ITEM NO.7.20/35)

9.1.5 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu. 3 pole MCCB, 125A, Adjustable Thermal - Magnetic Release, 25KA Incomer of Lighting Panel (ELECTRICAL SOR ITEM NO.9.1.5/50)

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps (ELECTRICAL SOR ITEM NO.9.16/44)

Providing and fixing 3 pole, 415/500 volts following rating (AC-1 Duty) power contactor in existing starter/ cubical panel including, connections, testing and commissioning etc. as per specification. 40 amps (ELECTRICAL SOR ITEM NO.10.13/48)

Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification. 50/5 amps (ELECTRICAL SOR ITEM NO.10.15/48)

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification.(ELECTRICAL SOR ITEM NO.10.17/49)

Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification. 0-100 amps (ELECTRICAL SOR ITEM NO.10.18/49)

Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification. Digital type (ELECTRICAL SOR ITEM NO.10.20/50)

Providing and fixing following Time switch (timer) in existing panel including connection, testing and commissioning as per specification. Analoge type (ELECTRICAL SOR ITEM NO.10.22/50)

Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification. (EL.SOR. ITEM NO.-12.13/49)

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering, excavation and refilling the trench etc. as per specification. (EL.SOR. ITEM NO.-12.12/49)

Human Sculptures Statue of Shri Guru Balak Das Ji (As per quotation) Providing & Fixing Shri Guru Balak Das Ji size gun metal statue at birgaon, Size 3.5' weight Approx-250 kg made of gun metal (alloy, copper zing, zinc, tin, Lead) colour Bronze paint 2k auto finish (glosy) and fixing at desired place i/c transportation complete.

UOM Name

Percentage

% of Cost of Bridge (excluding Maintenance) sanctioned by competent authority

Per mile

1000 piece

Print

Per Diem Rate

MAN DAYS

1 Piece

1 Strip

PRINT