CA NO.CWE BLY/ GE (E) /123 OF 2025-26SPECIAL REPAIR TO ROAD OF MAP QTRS FROM SIGNAL UNIT ENTRANCE JUNCTION TO BAGDAD GATE AND ROAD AT GOLF GROUND AT SHAHJAHANPUR CANTT UNDER GE (EAST) BAREILLY

M&L repair to potholes any depth, not exc 1 sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth and making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) but making good by applying tack coat with bituminous primer @ 5 kg per 10 sq m, putting in premix as specified for thin bituminous carpet 2 cm thick, well rammed and sealed with premixed sand seal coat (6.8 kg of binder with 0.06 cum of sand) and again well rammed (including supply of premixed binder and sand) depth of pot hole n.exc. 30mm complete all as specified and directed.

M&L for preparing existing black top surfaces of road by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and directed.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area n exc 400 sqm n exc 50 mm deep complete all as specified and directed.

M&L for applying evenly a priming/ tack coat with bituminous primer at 5 kg per 10 sq metre (Paving bitumen VG-10) complete all as specified and directed.

M&L for Premix bituminous, macadam with binder content of 4% by weight of total mix using paving bitumen VG-30 grade, laid/rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) complete all as specified and directed. Note :(i) Aggregates for Bituminous works shall confirm to clause No 20 B 2.5 of SSR 2009 Part- I (Specifications) with the following Constraints:- Aggregate passing 26.5 mm IS Sieve -100 % Aggregate passing13.20 mm IS Sieve -60% to 80% Aggregate passing 4.75 mm IS Sieve -20% to 30% Aggregate passing 2.36 mm IS Sieve -5% to 10%

S&F in replacement cat eye solar reflective type of metal body alloy of size 100 mm x 100mm x 20mm with PAMA striplens reflector of medel No DA 972.0 fixed with and including MS stud of suitable size as per manufacturers instructions complete.

S&F in replacement solar cat eye aluminium alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65 mm) of high efficiency Mono crystafie solar panel 2.4V /0.3 watt one NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactureres instructions etc all as specified and directed.

S&F in replacement metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed

M&L for preparing bituminous surface of road and marking 2.50 mm thick centre lines, dashes, arrows letter, marking etc and the like not exc 10 cm wide on new surface or previously treated road surface with hot applied retro-reflective thermoplastic road marking paint (white/ golden/ yellow) confirming to MORTH (clause 803.4) with 8% glass beads using special applicator machine with heating arregment upto 160 °C including cleaning and drying the existing road surfaces to ensure dust, oil, grease and moisture free surfaces before applying the paint complete all as specified and directed.

Demolition of brick (laid flat or edge) or brick tiles in floors, channels, kerbs aprons, etc. (each layer) complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan and any radius built in cement mortar 1:4 complete all as specified and directed.

M&L for broken stone or boulder Hardcore of guage n exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick , watered and rammed to a true surface etc complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick workor concrete surfaces in CM 1:4 using water proofing compound @ 3% by weight of cement complete all as specified and directed.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregates in sub base flooring complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Please Enable Macros to View BoQ information