Annual contract for miscellaneous office works

Amount

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Kiln seasoned and chemically treated hollock wood

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood a) 50x12 mm

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood a) 25x12 mm

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/Sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. a) 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum board conforming to IS: 2095: part I

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. a) 1.0 mm thick

Providing and fixing 22 mm thick and 90 mm wide top/side rail fixed to partition top/sides in 2nd class teak wood with French spirit polish complete as per the direction and satisfaction of Enginer in charge.

Providing & fixing 12mm thick and 100mm High, 2nd class teakwood skirting on partition & panelling etc. with French spirit polish with angular edges complete as per the direction and satisfaction of Engineer-in- charge.

Providing & fixing GI stud/Floor framing for full height/low ht/ medium ht partitioning with: - 50x55 mm channel 20 gauge horizontal, top middle and bottom metal channel securely fixed to the floor and ceiling @ 900 mm centre to centre, - 48 mm x 55 mm vertical G.I studs 20 gauge @ 600mm center to center fixed with the top and bottom channel i/c providing Hollock wood framework as sub-frame of size 40x50mm for doors/any cutouts i/c floor channel in the bottom complete as per the satisfaction and direction of Engineer in charge. (Only framing to be paid in this item).

Providing & fixing 8 mm plywood to existing partitions/paneling of approved make with MS screws etc. all complete. The cost includes for providing openings for electrical wiring & switches etc. complete as per the direction and satisfaction of Engineer-in- charge.

Providing and Fixing Panelled wall panelling in heritage style ,includes fixing of 8 mm Commercial Plywood over 12 mm commercial plyboard in approved pattern and style and skinned with 4 mm thick decorative veneer (MRP shall not be less than Rs. 1500/Sqm) conforming to IS: 1328 (type-1) to all the exposed surface of ply in directed sizes/style to receive 15 x 12 mm designer moulding in block pattern over the veneer surface, the edge of veneer to be fixed with teak wood side gola (25x15) to have square and clean edge. The said panelling to be fixed with provision to receive 100 x 12 mm teak wood skirting duly sprayed and polished with three or more coats of melamine polish coating in desired shade, all complete as per entire satisfaction of Engineer-in-charge. ( Note: the item includes cost of all material such as 12 mm plyboard for base,8 mm thick plywood,moulding,veneering,beading,stepper, all neccesarry screws , beadings required for making panels and all labour cost required for this item.The sample of veneer shall be approved by Engineer-in-charge. Framing & Skirting to be paid separately).

Providing & fixing designer wall paper (MRP shall not be less than Rs. 1000/sqm) over wall/partition including preparation of surface etc. as per direction and satisfaction of engineer in charge.

French spirit polishing : a) Two or more coats on new works including a coat of wood filler.

Melamine polishing on veneer and wood work by scrapping the veneer/wood surface by sand paper and preparing the surface for melamine polish by applying spirit, thinner, sealer, lacquer polish and applying approved colour on the prepared surface to give the uniform and desired colour/shade by air compressor and for final finish applying melamine polish on the veneer / wood surface by air compressor complete as per the direction and satisfaction of Engineer-in- charge.

Dismantling Aluminium / gypsum / wooden /PVC partition ,doors, windows,fixed glazing and false ceiling including disposal of unservicable surplus material and stacking of serviceable material within RGB premises as directed by Engineer-in-Charge.

Providing & fixing Storage unit/Side unit/Back unit at all floors of Depth 450 mm of required size all complete as per direction and satisfaction of Engineer-in- charge. : a) The carcase made of 18 mm thick commercial board sides/Front/shelves skirting/Bottom & top and back with 12 mm thick commercial board. The shelves are to be provided at height of 300 to 400 mm as per the direction of EIC. The edges of commercial board should be covered with 20X6mm wood margin and polished. b) The all outer surface (except back side) finished with 1.0 mm thick decorative / coloured high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. c) All inside surfaces and shelves shall be skinned with 0.65mm high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. d) Each shutter should be fixed with 2 / 3 nos. SS butt hinges of size 75X47X1.8 mm, one number 100 mm size S.S fancy handles (one on each shutter). The shutter should have 50mm size Nickeled chromium brass cupboard lock and another shutter should have 100X10 mm SS tower bolt. e) The shutter will be supported with Magnetic catcher triple strip vertical type. f) The shelves should be supported with two numbers SS shelf pin on each side. The areas not having Laminate shall be finished with polish. (For payment purpose Front area to be measured.) (Note: The item includes cost of all material and labour. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)

Providing and fixing 18 mm thick commercial Board in partitions paneling and for other works including fixing with 20X6 mm thick teak wood margin, necessary screws, nails etc. as per the direction and satisfaction Engineer-in-charge.

Providing & fixing drawer unit having size 400(W)X500(D)X600(H) mm as per direction & satisfaction of Engineer-in-charge. a) The carcase of drawer unit will be made of 18 mm thick Commercial board & edge should be protected with teak wood margin of size 20 x 6 mm duly polished. All exposed outer area should be laminated with 1.0 mm thick decorative / coloured high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. All inner surface shall be skinned with 0.65 mm high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality as balancing laminate for carcase. b) Drawers shall be made with combination of 8 mm and 12 mm thick plywood. Drawer's sides, back and front shall be made with 12 mm thick plywood of ht 100 mm for 1st upper drawer, 130 mm for 2nd drawer and of ht 225 mm for bottom drawer. The base of all drawers shall be made with 8 mm thick plywood. The front face of all drawers is to be fixed with 18 mm commercial board by screwing from inside having 0.65 mm laminates on all surface (both sides) except front face. Front face is laminated with 1 mm thick laminate. c) All drawers are to be hung on 450 mm long MS powder coated telescopic channels with 3 way locking system which locks all drawer in single time of approved make. All exposed edges of commercial board are to be covered with PVC edge bending tape. d) All drawers shall have 100 mm size SS fancy handles (one on each drawer) or as per instructions and satisfaction of Engineer-in-charge. (Note: The item includes cost of all material and labour. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)

Providing and Placing in Position laminated Working table of required size: a) The Working top of table is to be made with 18 mm thick commercial board having Single board pasted upon another board of width 150 mm at all sides to make it thick up to 36 mm at edges. b) The vertical support shall be of 18 mm thick commercial board for supporting working top of table and 18mm thick commercial board having height of 500 mm to 600 mm shall be fixed at front side as a front / modesty. c) Table top surface, both faces of vertical sides and Modesty / front shall be laminated with 1 mm thick decorative / coloured high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. d) The underside of table shall be skinned with 0.65 mm high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. e) Top to be fixed with 40 x 6 mm teak margin on front, vertical side to have 20 x 6 teak margin on front. The item includes cost of material, labour, nails, screws, adhesive, cut out for cables etc. to be provided wherever required. The item shall be as per direction and satisfaction of Engineer in Charge. (For payment purpose TOP surface area/ plan area will be measured). (Note: The item includes cost of all material and labour. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)

Providing and Placing in Position fully Veneered executive table of required size and shape: a) The working top of table is to be made with 18 mm thick commercial board having Single boards pasted upon another board of width 150 mm at all sides to make it thick upto 36 mm in edges. b) The vertical support shall be of 18mm thick commercial board for supporting working top of table and 18mm thick commercial board having height of 500 mm to 600 mm shall be fixed at front side as a front / modesty. c) Table top surface, both faces of vertical sides and Modesty / front shall be skinned with 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), (Natural sapeli/mahagony/walnut veneer) (MRP shall not be less than Rs. 1500/Sqm) and finally finished with melamine polish of desired shade/finish. d) The underside of table shall be skinned with 0.65 mm high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. e) Top to be fixed with 40 x 6 mm teak wood margin on front, vertical side to have 20 x 6 mm teak margin on front. The item includes cost of material, labour, nails, screws, adhesive, cut out for cables etc. to be provided wherever required. The item shall be as per direction and satisfaction of Engineer in Charge. (For payment purpose TOP surface area/ plan area will be measured). (Note: The item includes cost of all material and labour. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)

Providing & fixing fully veneered Storage unit/Side unit/Back unit at all floors of Depth 450 mm of required size all complete as per direction and satisfaction of Engineer-in- charge : a) The carcase made of 18 mm thick commercial board sides/Front/shelves skirting/Bottom & top and back with 12 mm thick commercial board. The shelves are to be provided at height of 300 to 400 mm as per the direction of EIC. The edges of commercial board should be covered with 20X6mm wood margin and polished. b) The carcase made of 18 mm thick commercial board, sides/Front/shelves/skirting/Bottom & top and back with 12 mm thick commercial plywood. Shelves to be provided at height of 300 to 400 mm as per the direction of EIC. c) The all outer surface (except back side) finished with 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), (Natural sapeli/mahagony/walnut veneer) (MRP shall not be less than Rs. 1500/Sqm) finished with melamine polish of desired shade/finish and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. d) All inside surfaces and shelves shall be skinned with 0.65mm high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality and if shutter is not provided than the exposed internal area to skinned with 4mm thick veneer. e) The each shutter should be fixed with 2 / 3 nos. SS butt hinges of size 75X47X1.8 mm, one number 100 mm size S.S fancy handles (one on each shutter). The shutter should have 50 mm size nickeled chromium brass cupboard lock and another shutter should have 100X10 mm SS tower bolt. f) The shutter will be supported with Magnetic catcher triple strip vertical type. g) The shelves should be supported with two numbers SS shelf pin on each side. h) The areas not having Veneer / Laminate shall be finished with melamine polish. (For payment purpose Front area to be measured.) (Note: the item includes cost of all material and labour. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)

Providing & fixing veneered drawer unit having size 400(W)X500(D)X600(H) mm as per direction & satisfaction of Engineer-in-charge. a) The carcase of drawer unit will be made of 18 mm thick commercial board & edge should be protected with teak wood margin of size 20 x 6 mm. It should be skinned with 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), (Natural sapeli/mahagony/walnut veneer) (MRP shall not be less than Rs. 1500/Sqm) and finally finished with melamine polish of desired shade/finish on all exposed outer area (except back surface) and with 0.65 mm laminate sheet as balancing laminate for carcase. b) Drawers shall be made with combination of 8 mm and 12 mm thick plywood. Drawer's sides, back and front shall be made with 12 mm thick plywood of ht 100 mm for 1st upper drawer, 130 mm for 2nd drawer and of ht 225 mm for bottom drawer. The base of all drawers shall be made with 8 mm thick plywood. The front face of all drawers is to be fixed with 18 mm commercial board by screwing from inside having 0.65 mm laminates on all surface (both sides) except front face. Front face is skinned with 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), (Natural sapeli/mahagony/walnut veneer) (MRP shall not be less than Rs. 1500/Sqm) and finally finished with melamine polish of desired shade/finish. c) All drawers are to be hung on 450 mm long MS powder coated telescopic channels with 3 way locking system which locks all drawer in single time of approved make. All exposed edges of commercial board are to be covered with PVC edge bending tape. d) All drawers shall have 100mm size SS fancy handles (one on each drawer) or as per instructions and satisfaction of Engineer-in-charge. (Note: The item includes cost of all material and labour. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)

Providing and placing fully vennered Heritege executive conference table of approved size/design/shape with following specification . (MRP of veneer shall not be less than Rs. 1500/- per sqm). a) Carcase or structure made of 18mm commercial board to support the table. b) The modesty of the table shall be throughout the periphery and such placed to have adequate space for the legs. c) Top made of 18mm board and in order to have additional thickness a 150 mm wide 18mm board will be finished throughout pheriphery beneth the top. d) The top of table will be skinned with 4mm thick ANERGRE or equivalent priced speices of veneer of approved brand confirming to IS:1328. e) The exposed edge of table shall be covered with 1st class teak wood moulding made out of size 50 X 25 mm to have designed, shape as per direction of Engineer-in-charge. f) The vertical support provided for strength at suitable location protruding from main base and edges shall be covered with teak wood margin of size 20x6 mm. g) The exposed surface of modesty shall have veneer, will be in heritage fashion. h) The blocks will be created in square or rectangle shape by fixing additional 8 mm commercial plywood on the existing 18 mm board and complimented with 25 X 15 mm and 35 X15 beading to have heritage effect on the periphery of supporting structure. i) Teak wood skirting of 100 X 12 mm all along the periphery of supporting structure. j) 4 mm thick lacqaure glass will be fixed on the top as per design and shape as approved by Engineer- In-Charge. k) The underside of the table top shall be laminated with 0.65 mm thick balancing laminate. l) All the venner and teak wood surface will be polished in melamine as per the shade/finish approved by Engineer in Charge. (Lacquer glass at top to be paid separately. Top surface/plan of table will be measured for payment purpose).( Note: the item includes cost of all material cost and labour.The quantity shown in item will be prepared on requirement not at once.Please read clause no 57 of SCC before quoting rate. )

Suppling and placing in position Designer Office Centre table , with frame made in carved 1 st class teak wood with appicted designs all over. The table to be of size 1050 x 600 mm with 8 mm bevelled edge glass, sparyed with base shadder and 2 coats of Dull melamine coating complete as per the direction and satisfaction of Engineer-in- charge.

Suppling and placing in position Designer Office Corner table , with frame made in carved 1 st class teak wood with appicted designs all over. The table to be of size 450 x 450 mm with 8 mm bevelled edge glass, sparyed with base shadder and 2 coats of Dull melamine coating complete as per the direction and satisfaction of Engineer-in- charge.

Providing and placing honour board for the offices as per direction and satisfaction of engineer-in-charge. (a) The carcase or structure of honour board will be made of 18mm thick commercial board having 20 mm X 18 mm thick teak wood leaping at the all around edges of board. The top of honour board will be in semi-circular shape or as instructed by Engineer-in-charge. (b) Font face including leaping of honour board will be skinned with 4mm thick Natural sapeli/mahagony/walnut veneer and finished with melamine polise of disered shade/ finish. (c) The back side of honour board will be laminated with 0.65 mm thick balancing laminated sheet. (d) All exposed edges of honour board will be covered with PVC edge wending tape. Item includes cost of material, hanging clips on wall surface, fevicol , necessary screws, labour and fittings etc. For payment purpose front face will be measure.

Providing and fixing of 4 mm thick lacquer glass of required size with fixing arrangment as per the location (lacquered with MTG) SGG Planileque (Black/Pista Green/Atoll Blu/ Calm Sky/ Cool Earth/ Solar Yellow/ Opera Red/ Casis Purple/ Almond Green/ Olive Green/ Choco Brown) or approved equivalent with clear neutral silicon of make GE winsil 20/ silpruf / DOW CORNING 995 / equivalent on a perfectly leveled existing surface. The SGG Planilaque lacquered glass is highly durable, humid resistance, poly urethane lacquer glass.

Providing and placing clear transparent shield / barrier on table made of 5mm thick clear acrylic plastic sheet (Acast / Modern Glass / Astari) fixed with required L,U brackets / stands and screws. The stands / brackets should also made of acrylic sheet and should be placed at appropriate place to hold the sheet to be acted as shield / barrier against corona virus. The sheet edges stand should have square edges cut with lazar cutter. The sheet should be scratch free and of quality as approved by Engineer-in-charge. The net front elevation / net area of acrylic sheet will be measured and nothing extra will be paid on account of stand.

Providing and placing single / double / triple seater fully laminated wooden satties having size of 450 mm (W) X 500 mm (H) at all floors as per direction and satisfaction of Engineer-in-charge. a) The all sides (sides/Front/Back/Bottom & top) of carcase is made of 18 mm thick commercial board of approved make. The front side of carcase should have openable shutter to keep personal belonging inside the satty. The edges of commercial board should be covered with 20X6mm teak wood margin. b) All outer surface (except back side) finished with 1.0 mm thick decorative / coloured high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.. c)All inside surfaces and shelves shall be skinned with 0.65mm high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. d) Each shutter should be fixed with 2 nos. SS butt hinges of size 75X47X1.8 mm, one number 100 mm size S.S fancy handles on each shutter. The shutter should have 50mm size Nickeled chromium brass cupboard lock. f) 100mm thick foam seat having density 40 kg per cubic metre and upholstered with leatherite is to be placed at top of satty for sitting purpose. The leatherite foam seat shall be placed 2 inch below the top. There is a separation of 150mm between two seats by 18 mm commercial board in a satty. The top of separator is laminated with 1.0 mm thick decorative / coloured high pressure laminated sheet. The areas not having Laminate shall be finished with polish. (For payment purpose length of top surface will be measured).

kailash chawla

CREATORS ENGINEERS AND INTERIORS