GE CHD T 108 2025 26

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer-in-Charge.

Demolishing of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part there of) and including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer-in-Charge.

Dismantling existing brick tiles or terracing tiles, single layer on roofs from any position grouted in cement mortar, complete including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats with shutters (without taking off shutter from frame) n exc 1.5 Sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutter from frame)exc 1.5 Sqm but n exc 4 sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down and refxing of shutter in same opening of any description size but exc 1 sqm and n.exc 2 complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed by Engr-In-Charge.

Cutting chases in stone wall, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc 10 cm girth and complete all as specified and directed by Engineer-in-Charge.

Cutting holes in brick walls in mud mortar for inserting holdfasts andmaking good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc using acetic acid and citric acid used for descaling and removing mineral deposite from tank (capacity exc 200 but n exc 500 ltr), Complete all as specified and as directed

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc,including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer-in-Charge.

Dismantling existing tanks of capacity exc 500 ltr but not exc 1000 ltr and removing to store complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment preparation of wall and applying two coats of oil bound distemper on walls over and including a coat of primer and 1 mm wall care puty complete all as specified and directed.

Plain cement concrete (1:7:12) type F-2,using 40 mm graded stone aggregate as in sunken floor etc complete all as specified and directed by Engineer-in-Charge.

Providing, cement concrete PCC 1:2:4 type B-1 (using 12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs stone, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engineer-in-Charge.

25 mm thick Cement concrete (1:2:4) type B-1,using 20 mm graded mechanically crushed stone aggregate as in levelling concrete etc. complete all as specified and directed by Engineer-in-Charge.

Material and labour for providing 40 mm Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in flooring including finishing the cement concrete surface even and smooth with using extra cement complete all as specified and directed.

Plain cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base to paver blocks etc complete all as specified and directed by Engineer-in-Charge.

75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified.Plinth protection shall be laid in 1:20 slope and joint filling sealed with bituminous sealing compound grade "A" .

Glazed ceramic coloured tiles 600 x 300 x 7 mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed with 4 mm spacer and grouting the joint of wall with epoxy grout mix of organic coated filler of desired shade, hardener, resin in the ratio of 8:1:2 complete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic tiles coloured Light shade (sctratch and stain resistant tiles) 9 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floor,skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 10mm thick screed bedding layer in CM (1:6) complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc. set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Out door/parking tiles heavy duty for light traffic Non skid,anti scratch,heavy grip ,vitreous/semi vitreous coloured ,unique designs tiles 8 to 10 mm thick area of each tile of size 300 mm x 300 mm, in floors parking/outdoortiles etc. set and jointed setting & jointed with 4 mm spacer and grouting the joint with epoxy grout mix of organic coated filler of desired shade , hardener,resin in the ratio of 8:1:2 over & including 15mm thick bedding of cement sand mortar (1:6) and pointed with appoxy coloured cement to match with surface of tiles complete all as specified and as directed.

Green Marble work 16 to 18 mm thick (table rubbed and Pre polished) in steps (Treads/Riser/Skirting), jambs, pillars, window cills, cooking platforms and like over 15mm thick screed bed/back coat in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including Bull nose Rounding to edges of stone slabs, such as in steps, cooking platform, and other similar works complete all as specified

Material and labour for chamfering half rounding of edges of cudappa/ granite slab as in platform vertical support and edge poloshing complete all as specified and directed.

Material and labour for 10 mm thick cement plaster in CM (1:3) using WPC on RCC roof slab/sunken including cleaningof existing surface complete all as specified and directed by Engineer-in-Charge. Note:- WPC shall be measured and paid separately.

Material and labour for providing 25mm thick cement concrete type B-0 (1:2:4) 12.5 mm graded aggregate in roof kerbs, mud slopes or roof padding , complete all as specified and directed by Engineer-in-Charge.

Water proofing roof treatment using APP polymeric ( on roof/sunken portion) water proofing membrane minimum 3 mm thick and weighting not less than 3.0 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm over cleaned surface including parapet,applying a coat of blown bitumen 85/25 grade @ 1.2 kg per square metre over priming coat torching over laps with a propane or butan gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing all as per manufacturers instructions incl wire brushing and cleaning the top surfaces of concrete, roof surfaces etc. with water including flashings and junction of parapets etc complete all as specified and directed.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 5 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Supply only liquid water proofing comound ISI Marked complete all as specified and directed.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

30 mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercialm type with 0.80 mm mica on both sides complet all as specified and directed.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frame of doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 200 mm, ISI marked complete all as specified and directed by Engineer-in-Charge.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 100 mm, ISI marked complete all as specified and directed by Engineer-in-Charge.

300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

150 mm long Aluminium extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed by Engineer-in-Charge.

100 mm long Aluminium extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed by Engineer-in-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 140 mm complete all as specified and directed by Engineer-in-Charge.

Continuous (piano hinges) 30mm width of flap in repairs Paino hinges SS Gde-304 (width of flap 30mm) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair door closer (Aluminium die cast body) hydraulically regulated,designation No. 2,universal type, suitablefor door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed by Engineer-in-Charge.

300 mm, ordinary rat tail rod pattern springs including roller and roller plate fixed in repair complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete fixed in reapir all as specified and directed by Engineer-in-Charge.

Sheet glass 4mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane complete all as specified and directed by Engineer-in-Charge.

Sheet glass 5mm thick tinted/plain/Figured glass type, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane complete all as specified and directed by Engineer-in-Charge.

5.5 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Stainless steel work such as Frames , grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred doors;ladders; framed balusters; walk ways; railings work conforming to grade 304 complete all as specified and directed.

Supply and fixing in repair for Vitreous China wash down water closet pan ( pedestal pattern) white ( including 6mm dia 50mm long fixing mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexgonal or square nut) with plasticc water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device with 32 mm PTMT flush pipes to pedestal pan, including all joints complete all as specified and directed.

Supply and fixing in repair for Vitreous China wash down water closet pan including connection to drain or out going pipes single piece with seat cover complete all as specified and directed. Make:- jaqare(CAT Part No. SLS-WHT-6851S300PP), Cera (Cat Part No. A-1014108), Hindware (Cat Part No. 92562-S-22).

Supply and fixing in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed. Note:- Flush pipe and flushing cistern to be measured and paid separately.

Vitreous China wash basin, white, flat back, size 550 x 400mm excluding taps waste, chain and plug and porcelain stopper but including brackets but including brackets 32 mm waste fittings, brass, chromium plated for glazed ware sink, basins, etc. with long screwed shanks and fly-nts, flange end bedded in red lead cement other and fixed complete all as specified.

Supply and fixing in repair 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Brass chromum plated 3‐In‐1 System wall mixer with Provision for both hand shower and overhead Shower for mixing hot and cold water fancy type with screwed down for 15mm dia iron pipe With 115mm Long Bend Pipe, Connecting Legs & Wall Flange complete all as specified and directed by Engineer-in-Charge.CAT FLR 5267N of jaquar or equivlaent of Hindware, Cera, Somany complete all as specified and directed.

Supply and fixed in repair Brass chromum plated wall mixer non telephonic, fancy type 15mm dia for mixing hot and cold water with screwed down for iron pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair brass chromum plated single lever centre hole basin mixer without popup waste system wround spout with 375 mm long braided hoses complete all as specified and as directed. CAT FLR 5167B of jaquar or equivlaent of Hindware, Cera, Somany complete all as specified and directed.

S&F 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down fancy type high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 20 mm Gun-metal, globe or gate valves, with MS lever handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Health faucet (ABS Body) mild steel chromium plated suitable for 8 mm dia pipe with 1 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed

Supply and fixing in repairs hand shower of size 25 mm x 38 mm oval shape single flow (ABS body and face plate) chromium plated with rubit cleaning system complete all as specified and directed. Make : Jaquar (Cat part No HSH-49537) or equivlaent of Cera, Somany

Supply and fixing in repairs toilet paper holder chromium plated with fixing to wall complete all as specified and directed.

Supply and fixing in repair brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flange, Complete all as specified and as directed

Supplying and fixing chromium plated shower rose 125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint in including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

Supply and fixing glass shelf assembly 5.5mm thick, 12 cm wide and 60 cm long fixed with & including chromium plated brass screws and stainless steel cleats and frame (Minimum weight 300gms) fixed in repair complete all as specified and as directed.

Supply and fixing corner glass shelf assembly 5.5mm thick (set of three of size 250 X 250 mm, 200 X 200 mm & 150 X 150 mm ) fixed with & including chromium plated brass screws and stainless steel cleats and frame (Minimum weight 300gms) fixed in repair complete all as specified and as directed.

Supply and fixing sinks without drainage board made of stainless steel minimum 1mm thick kitchen or laboratory with plugs, washers and wastes ,waste pipe ,coupling; including bedding in cement mortar fixing cantilever brackets and connecting union to pipe,overall size 595 mm X 520 mm ,bowl size 510 mm X 430 mm X260 mm conforming to grade 304 complete all as specified and directed.

Supply and fixing for PVC connections with PTMT nuts of length 450 mm long fixed to 15 mm bore iron pipe or union as in repair complete all as specified and as directed.

Steel water tubes, 15 mm bore, medium grade, galvanized, with all fitting and fixed complete to walls and ceilings or laid in floorscomplete all as specified and directed by Engineer - in -Charge.

Steel water tubes, 20 mm bore, medium grade, galvanized, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer - in -Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.

Supply and fixing 2nd class hard wood Plain fillets. square, rectangular or triangular in section, Exc 6 & n exc 13 sq.cm clean sawn, secured with nails or brads complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directerd.

Material and labour for Polythene film, 400 micron thick, white over sand cushioning complete all as specified and directed.

Supply only river bed fine sand for screed bed min 25mm thick for paving flooring complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Preparation of new/old concrete surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of primer and 1 mm wall care puty including preparation of surface complete all as specified and directed.

Material and labour for preparation of old decorated brick/concrete/ plastered or unplastered surfaces by brooming or by steel wire brushing, scrapping down snow soot,moulds, moss and efflorescent salts and treading oil and greasy spots, of walls including corinces pillars etc filling the all holes / patches with wall care putty to make surface smooth wherever required and applying one coats of oil bound distemper complete all as specified and directed.

Providing and applying cement base putty of 1 mm thickness over plastered surface to prepare the surface even and smooth (New / Old work )complete all as specified and directed.

Preparation of new plastered surfaces of wall and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Preparation of New Plastered of ceiling, applying two coats of oil bound distemper on walls over and including a coat of alkali resistant primer and 1 mm wall care putty complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs drapery rods/ curtain rods stainless steel pipe (fancy type) 20-25 mm in dia with end SS brackets & knobs, funnels fixed with rawl plug and screws, including taking down old curtain rod/ wooden pelmet complete all as specified and directed.

Chrome plated grating 110 mm dia with locking system (with/without hole ) complete all as specified and directed by Engineer-in-Charge.

Stainless steel plate rack of standard size 750 mm x 750mm x 250 mm complete and fixing with rawl plug and steel screws of weight upto 8/10 kg fixed in repair complete all as specified and directed by Engineer in Charge.

Material and labour for roof cleaning by cutting or uprooting grasss, vegetation and small plants etc from the roof/ wall, including making good cement plaster/ concrete surface as specified and directed and removing rubbish off the premises, cleaning the surface complete all as specified and directed

Material and labour Anit-termite of void in masonry injecting, using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement: 2 coarse sand ) to match the existing floors complete all as specified and directed.

Material and labour Anit-termite At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

INTERNAL ELECTRIC SUPPLY WORKS

Disconnection and removing theu/s MCB plug and socket unit and S&F single pole and nutral Enclosure with a two pin earth plug and socket complete controlled by one single pole MCB 20 Amps 240 Volts, complete all as specified and directed.

Taking down MCB DB/ TPN of any size and removal from site and making good disturbed surfaces complete all as specified and directed.

Taking down existing unserviceable sub main wiring with 2 Runs/4 Runs of 2.5/4/6/10 Sqmm aluminum/copper cable all as directed by Engr-in-charge.

Disconnection and removing the u/s casing caping conduit and Supply and fixing PVC casing caping of size 30mm including cut to shape and size to match the existing conduits suitable for LT electric supply along with necessary fixing arrangements complete all as specified and directed.

Same all as per item No 123 above but controlled by two way switch

Same all as per item No 123, One 3 pin 5 Amps socket outlet on independent board

Same all as per item No 123, One 3 pin 5 Amps socket outlet on same board with other switches

Same all as per item No 123, One bell/buzzeer point controlled by one bell push.

Ceiling rose surface backlite 65 x 20mm size three terminal complete all as specified and directed.

Electric bell AC, ding-dong type, 230 Volt, single pole complete all as specified and directed.

Modular snap Switch one way 16 Amps one module complete all as specified and directed.

Modular snap Switch one way 6 Amps one module complete all as specified and directed.

Modular snap Switch two way 5 Amps one module complete all as specified and directed.

Modular Bell Push 6 Amps one module complete all as specified and directed.

Modular Socket 6/16Amps 5 Pin 2 Module complete all as specified and directed.

Modular Socket 5/6Amps 5 Pin 2 Module complete all as specified and directed.

Modular fan Regulator step electronic type 2 module complete all as specified and directed.

Distribution Board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, MCB DB 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as specified and directed.

Distribution Board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, 8 way TPN, 415 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as specified and directed.

MCB SPN 40-63 Amp,240 volts,50Hz, 10KA, 'C' series ISI marked as incoming and outgoing controlling circuit all as specified and directed.

MCB SP 6- 32 Amps, 220 volts , 50 Hzs, 10 KA , "C" series, ISI marked all as specified and directed.

Sub main wiring using approved colour coding as per IS with two runs of 4 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 4 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor as earth wire connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Three runs ( main ) of 4.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

Sub main wiring using approved colour coding as per IS with two runs of 6 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 6 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor as earth wire connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Three runs ( main ) of 6.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

Lamp holder, PVC/ Polycarbonate type with back plate with and including one no of LED bulb 15 watt Base-22 retrofit type complete all as specified & directed.

LED lights fitting 1x 20 Watt, 220V,AC decorative box type,aluminium body with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including 20 watt LED tube rod complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Suplly and fixing decorative post top LED 40 Watt for 360* indirect light with IP 65 protection 230 volts with internally pre-wired and including connecting up with two core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing ceiling mounted slim design LED recessed Square/round downlight with superior light output and internal driver 15/18 Watts 230 volts with internally pre-wired and including connecting up with two core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 105071.50 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

Please Enable Macros to View BoQ information