PROPOSED COMMUNITY HALL CUM WORK SHED WITH URINAL & WATER POINT IN VILLAGE/TOLA - RAMGANJ , PANCHAYAT- NOHSHA , THANA NO 390 , KHATA NO 30 , KHESRA NO- 265 UNDER, BLOCK - BEN.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia pile

Earth work in excavation in foundtion trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead.

Supplying and Filling in plinth with local sand and under floors including watering, ramming consolidating and dressing complete.

1:2:4(1 Cement:3 coarse sand: 6 graded stone aggregate 20mm nominal size)

1:4:8(1 Cement:4 coarse sand: 8 graded stone aggregate 20mm nominal size)

Foundations, footings, bases for columns

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4{1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water profing material in cement concrete work in the proportion recommended by the manufacturers.

Providing and laying in position specified Mix of reinforced cement concrete excluding the cost of centring,shuttering.finishing and reinforcement-All work puto plinth level 1:1:5:3(1 cement:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (anythickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finisnin and reinforcement 1:1:5:3(1 cement:1.5 coarse sand.3 graded stone aggregate 20mm nominal size)

Beams, planth beams, girders, bressumers, contilevers, Suspended floors lintels roofs and staircases including spiral staircases, shelves etc.

Centering and shuttering including strutting, propping etc. and removal of form for:

Metre

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete.

Brick work with bricks of class designation 100A in foundation and plinth in:

Extra for Brick work in superstructure above plinth level upto floor V Level

Brick work 7cm thick with F.P.S brick of class designation 100A in cement mortar 1:3(1 cement: 3 coarse sand) in superstructure.

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Extra for half Brick masonry in superstructure above pinth level upto floor V level.

Providing wood work in frames of doors,windows, clerestory windows and other frames, wrought framed and fixed in position

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube,the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to beprovided through out theframe.The doorframetobefixedto thewall usingM.S. screwsof 65/100mm size,complete asper manufacturer’s specification and direction of Engineer-in-Charge

35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm,out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel,all complete as per manufacturer’s specification and direction of Engineer-incharge

Providing and fixing flush door shutters non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers including necessary screws etc. complete.(best make of approved quality)

Providing and fixing aluminium but each anodised (anodic coating not less than grade AC 10 as transport or dyed requirement colour or shade with necessary screws etc.complete

Providing and fixing aluminium sliding door bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium handles anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing bright finished brass 100mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS:1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing and fixing aluminium tee chanals(heavy duty)with rollers,stop end in pelmets as curtain rod i

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitred and welded with 15x3mm lugs, 10cm long, with steel lugs embedded in cement concrete blocks 15x10x10cm of 1:3:6( 1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer, excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Extra for providing and fixing steel beading of approved shape and section with screw instead of glazing clips and metal sash putty in steel doors, windows, ventilators and composite units.

Providing and fixing pressed steel door confirming IS code 351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

metre

Providing and fixing circular cast iron box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one ;pcf at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing bright finished brass casement window fastners of minimum weight 200 gms to side hung steel windows with necessary welding and machine screws etc. complete.

Providing and fixing bright finished brass peg stays 300mm long of minimum weight 330 gms. to side hung steel windows with necessary welding and machine screws etc. complete.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying apriming coat of approved steel primer

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with greycement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand

Providing and laying Ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in all colours, shades, White, Ivory, Grey, Fume Red Brow laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement: 4 Coarse sand) including pointing the joints with white cement and matching pigments etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622(thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing designation 100A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

12mm cement plaster of mix:

15mm cement plaster on the rough side of single or half brick wall of mix:

20mm cement plaster of mix:

1:6(1 cement: 6 coarse sand)

6mm cement plaster to ceiling of mix:

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of neat cement

Providing 20mm (1:3) water proofing cement plaster with punning

White washing with lime to give an ever shade

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Providing and fixing water closet squatting pan (Indian type W.C pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required:

Provding and fixing soil,waste and vent pipes

metre

Provding and fixing heel rest sanitary bend

Provding and fixing single equal plain junction of required degree with access door ,insertion rubber washer 3mm thick ,bolt and nuts complete

Provding and fixing terminal guard

Providing and fixing on wall face unplasticised-PVC (working pressure 4 Kgf per sqm) rain water pipes conforming to IS:4985including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion

Metre

Providing and fixing on wall face unplasticised -PVC moulded fittings/ accessories for unplasticised PVC rainwater pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S screws of required length including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Excavating trenches of required width for pipes, cables etc including excavation for sockets and dressing of sides, ramming of bottoms depth upto 1.5m ,including getting out the excavated soil , and then returning the soil as required,in the layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming watering and desposing of surplus excavated soil as dirceted within a lead of 50m

pipes cables etc exceeding 80mm dia but not exceeding 300 mm dia

India mark-II Hand Pump with all accessories including 8 Nos. (3 Mtr length each) connecting rod and one syllinder Confirming IS: 155000 (Part 1-8)/2008

125 mm dia UPVC Casing Pipe confirming to IS : 12818-1983/1992

32 mm dia medium quality G.I. Riser Pipe and 8 Nos. 3 mtre length (3 mtr each length confirming IS:1239

40 mm dia x 2 mtr, long UPVC RIBEED Strainer confirming to IS : 12818 - 1983/1992

125 mm dia x 40 mm x UPVC reducing socket (Heavy Quality)

40 mm nominal outer dia CPVC Pipe

Supplying all materials labours and equipement for constructing platform with foot rest etc. all complete job.(Detail Est attached)

Supplying drain 3 m as per design etc. all complete job.(Detail Est Attached)

Boring by jet dheki by suitable cutter or reduce as the case may be lowering 125 mm UPVC x 40 mm dia G.I. Pipe & Strainer of standard quality iron shoe, plug & socket etc. all complete including providing all tools and oplants required for the job as per sopecification and direction of the engineer in charge.

Supplying labour and equipment including 125 mm dia G.I. cap & fitting and fixing over the T/W properly and taking it out as per direction of E.I. (Cap will be property of the contractor) 1 No.

Providing all labours for fitting and fixing of India mark II hand pump including supplying all tools and plants requred for the all job complete as per direction of E/I.

Supplying all tools equipment all labours for lowering 32 mm dia medium quality G.I. Pipe (Riser pipe) in drilled T/W in 3 mtrs lenth

Providing all labour for fitting and fixing of deep cylinder with the riser pipe including necessary connecting and jointing materials, chrom leather bucket all tools & plants required for the job low water lever all complete job as per specification and direction of E/I.

Supplying all materials & labours for arrangement of additional water required during the drilling work all complete job as per specification and direction of E/I.

Developing and t Testing of T/W till the discharge is free from sand one item all complete job as per specification and direction of E/I.

50 mm size brick aggrigate outer side of soak pit

Wiring for light point/ fan point/ exhaust fan point / call bell point with 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit with piano type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq mm FR PVC insulated copper conductor single core cable etc as required. Group- B a. Light/ call bell points - 27 b. Ceiling fan points - 07 c. Ex. Fan points - 02 Total - 36

Supplying and fixing 3 pin 5/6 amps socket outlet & 6A switch piano type on the existing switch box including connections etc. as required.

Supplying and fixing suitable size GI/PVC box on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outlet & 6A switch piano type connection painting etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade copper conductor PE insulated, with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing piano type T.V antenna socket on the existing metal box including making connection, etc. as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required.

2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire (Circuit wiiring)

4 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire

Supplying and fixing metal box of following size in recess with suitable size of phenolic laminated sheet cover in the front including painting etc. as required.

75mmX75mmX60mm

Supplying and fixing 8 way double door sinle pole and Neutral sheet steel M.C.B. D.B, 240 Volts in recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar , detachable gland plate, interconnection, phosphatized and powder painted including nting, earthing etc. as required ( But without MCB/ RCCB/Isolator)(UPS DB)

Supplying and fixing of following rating C series MCB suitable for inductive and other loads of following poles in the existing MCB DB complete witth connections ,testing and commissioning etc. as required .

6 Amp. To 32 Amp. SP MCB 240 Volt

32 Amp SPN MCB 240 Volt

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. 9/10 watt

Supplying and fixing 2 pin 5 Amp ceiling rose on the existing junction box/ PVC box including connection etc as required.

Supplying and fixing batten / angle holder including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable etc. as required.

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required 200 mm sweep (1300/1400 RPM)

Supplying and fixing 4'X18 wat[ LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS pVC insulated copper conductor etc. as required.

th nos

E.E L.A.E.O, Work Div-1 Biharsharif

E.E L.A.E.O, Work Div-1 BIHARSHARIF

DESCRIPTION

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m

Earth work in excavation in foundtion trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead.

Supplying and Filling in plinth with local sand and under floors including watering, ramming consolidating and dressing complete.

1:2:4(1 Cement:3 coarse sand: 6 graded stone aggregate 20mm nominal size)

1:4:8(1 Cement:4 coarse sand: 8 graded stone aggregate 20mm nominal size)

Foundations, footings, bases for columns

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4{1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water profing material in cement concrete work in the proportion recommended by the manufacturers.

Providing and laying in position specified Mix of reinforced cement concrete excluding the cost of centring,shuttering.finishing and reinforcement-All work puto plinth level 1:1:5:3(1 cement:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (anythickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finisnin and reinforcement 1:1:5:3(1 cement:1.5 coarse sand.3 graded stone aggregate 20mm nominal size)

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 150, landings.balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level exdudingthe cost of centring, shuttering, finishing and reinforement with 1:1.5:3(1 cement:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for:

Metre

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete.

Brick work with bricks of class designation 100A in foundation and plinth in:

Extra for Brick work in superstructure above plinth level upto floor V Level

Brick work 7cm thick with F.P.S brick of class designation 100A in cement mortar 1:3(1 cement: 3 coarse sand) in superstructure.

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Extra for half Brick masonry in superstructure above pinth level upto floor V level.

Providing wood work in frames of doors,windows, clerestory windows and other frames, wrought framed and fixed in position

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube,the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to beprovided through out theframe.The doorframetobefixedto thewall usingM.S. screwsof 65/100mm size,complete asper manufacturer’s specification and direction of Engineer-in-Charge

35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm,out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel,all complete as per manufacturer’s specification and direction of Engineer-incharge

Providing and fixing flush door shutters non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers including necessary screws etc. complete.(best make of approved quality)

Providing and fixing aluminium but each anodised (anodic coating not less than grade AC 10 as transport or dyed requirement colour or shade with necessary screws etc.complete

Providing and fixing aluminium sliding door bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium handles anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing bright finished brass 100mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS:1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing and fixing aluminium tee chanals(heavy duty)with rollers,stop end in pelmets as curtain rod i

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitred and welded with 15x3mm lugs, 10cm long, with steel lugs embedded in cement concrete blocks 15x10x10cm of 1:3:6( 1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer, excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Extra for providing and fixing steel beading of approved shape and section with screw instead of glazing clips and metal sash putty in steel doors, windows, ventilators and composite units.

Providing and fixing pressed steel door confirming IS code 351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

metre

Providing and fixing circular cast iron box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one ;pcf at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing bright finished brass casement window fastners of minimum weight 200 gms to side hung steel windows with necessary welding and machine screws etc. complete.

Providing and fixing bright finished brass peg stays 300mm long of minimum weight 330 gms. to side hung steel windows with necessary welding and machine screws etc. complete.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying apriming coat of approved steel primer

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Providing and laying Ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in all colours, shades, White, Ivory, Grey, Fume Red Brow laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement: 4 Coarse sand) including pointing the joints with white cement and matching pigments etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622(thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with greycement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand

Providing designation 100A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

12mm cement plaster of mix:

15mm cement plaster on the rough side of single or half brick wall of mix:

20mm cement plaster of mix:

6mm cement plaster to ceiling of mix:

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of neat cement

Providing 20mm (1:3) water proofing cement plaster with punning

White washing with lime to give an ever shade

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

E.E L.A.E.O, Work Div-1 BIHARSHARIF

DESCRIPTION

Providing and installing in situ single under reamed piles

Surface dressing of the ground

Earth work in excavation in foundation

Earth work in back filling

S/Filing Local sand in Foundation&Plinth

P/L PCC In

Centering and shuttering for PCC work

Providing 50 mm th. DPC at plinth level

Extra for providing water proofing material

Prov.RCC M20-grade

(a)Walls columns, pillars, posts cind struts

roof beam, Roof slab,Lintel,Stair case,Chajja, Band

Centering&shuttering

Extra for additional height in centring,

Reinforcement for RCC work

100A Brick work in Cm 1:6 in F/p

Extra for Brick work in superstructure above plinth level

7 cm Brick work with bricks ofclass 100A in CM

Half brick work with bricks of100 in cm 1:4

Extra for half Brick masonry in superstructure above pinth level

Sal wood in choukhat of doors

Providing and fixing factory made P.V.C. door frame

Providing and fixing factory made Solid panel PVC door shutter

P/F non decorative flush door shutter

P& F M.S grills

P & F cupboard or ward robe locks

Providing and fixing aluminium but hinge

P&F Alluminium sliding door bolt

P&F Alluminium sliding tower bolt

P&F Alluminium handles

P&FAlluminium hanging floor door stopper

Bright finished 100mm mortice lock

Providing and fixing aluminium tee curtain rod

P&F steel windows& ventilator

Extra for steel beading

Providing and fixing pressed steel door

Providing and fixing circular cast iron box for ceiling fan clamp

Steel window fastner

Steel window peg stays

Steel work welded in built up sections

40mm dia G.I pipe in stair hand rail

40 MM Th.Cement concrete flooring 1:2:4(

18 mm th.Cement plaster 1:3 in skirting

Providing and Laying 300 x300 mmCeramic

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with greycement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand

Ceramic glazed wall tiles in dado

100A one brick flat soling in plinth

Internal Cement Plaster

15mm CP 1:6 in internal surfaces

20mm CP 1:4 in external surfaces

6mm CP 1:4 in ceiling

Providing 20mm (1:3) water proofing cement plaster with punning

12 mm cement plaster 1:3

White Lime wash

Water proof cement paint

Applying priming coat

synthetic enamel paint on wooden & steel

E.E L.A.E.O, Work Div-1 BIHARSHARIF

Name of Items

local sand filling

D.P.C. 50 mm (1:2:4)

100A Brick Work (1:6)

100A Brick Work 7 c.m (1:3)

100A half Brick Work (1:4)

cement concrete flooring 40 mm thick

18 mm c.p.(1:3) with

ceramic glazed floor tiles

ceramic glazed wall tiles

100 A brick flat soling

150mm rammed khoa

instalation pile boring

local sand filling

Brick flat soling

100 A brick work

local sand filling

Brick flat soling

100A Brick Work (1:4)

100A Brick Work (1:6)

50 mm size brick aggrigate

Ghorasahan

ANALYSED RATE (BASIC RATE)

CARRIAGE COST

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m ----------(For all Kinds of Soil)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m

PCC(1:1.5:3)-M20-----(All works Up to Plinth Level)

PCC(1:2:4)-M15---(All works Up to Plinth Level)

PCC(1:3:6)-M10-----(All works Up to Plinth Level)

PCC(1:4:8)--M7.5---(All works Up to Plinth Level)

DPC(1:2:4)-Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Extra for Providing and mixing water -proofing material in cement concrte work in the proportion recommended by the manufactures

RCC(1:1.5:3)--M20----(All works Up to Plinth Level)

RCC(1:1.5:3)-M20--wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc.---(All works Above Plinth Level up to V-Floor))

RCC(1:2:4)-M15-beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases etc ---(Above Plinth Level up to V-Floor))

RCC(1:1.5:3)-M20---Reinforced cement concrete work in Vertical and Horizontal fins individually or forming box louvers, facias and eaves boards--(Above Plinth Level up to V-Floor)) size)-----(Above Plinth Level up to V-Floor))

RCC(1:1.5:3)-M20---(All works Up to Plinth Level)

RCC(1:1.5:3)-M20----(All works Above Plinth Level)-Walls, Columns, Pillars,Posts, Struts etc

RCC(1:1.5:3)-M20-Beams, planth beams, girders, bressumers, contilevers, Suspended floors lintels roofs and staircases including spiral staircases, shelves etc.---------(All works Above Plinth Level)

Add or Deduct for richer or leaner mixes- -(Providing M-25 grade RCC instead of M20 grade RCC )-At all Floor- Level

Add or Deduct for richer or leaner mixes- -(Providing M-15 grade RCC instead of M20 grade RCC )-At all Floor- Level

B/W (100A)-In Cement mortar 1:4 (1 cement: 4 coarse sand )-Brick work in Foundation and Plinth -Up to Plinth- Level

B/W (100A)-In Cement mortar 1:6 (1 cement: 6 coarse sand )-Brick work in Foundation and Plinth -Up to Plinth- Level

Add Extra for B/W in superstructure -Up to Floor V- Level

B/W (100A)-In Cement mortar 1:6 (1 cement : 6 coarse sand )-B/W in superstructure-Up to Floor-V- Level

B/W (100A)-In Cement mortar 1:3 (1 cement : 3 coarse sand )- Providing B/W in half brick masonry in super structure for closing cavity 5 to 7.5 cm widei cavity wall--Up to Floor-V- Level

B/W (100A)-In Cement mortar 1:4 (1 cement : 4 coarse sand )-Half Brick masonary in foundation and Plinth

B/W (Class-100A)-Extra for Half Brick masonary in superstructure above plinth up to V-Level

B/W (100A)-In Cement mortar 1:4 (1 cement : 4 coarse sand )-Half Brick masonary in superstructure above plinth up to V-Level

B/W (100B)-In Cement mortar 1:4 (1 cement: 4 coarse sand )-Brick work in Foundation and Plinth -Up to Plinth- Level

B/W (100B)-In Cement mortar 1:6 (1 cement: 6 coarse sand )-Brick work in Foundation and Plinth -Up to Plinth- Level

Add Extra for B/W in superstructure -Up to Floor V- Level

B/W (100B)-In Cement mortar 1:6 (1 cement : 6 coarse sand )-B/W in superstructure-Up to Floor-V- Level

B/W (100B)-In Cement mortar 1:3 (1 cement : 3 coarse sand )- Providing B/W in half brick masonry in super structure for closing cavity 5 to 7.5 cm widei cavity wall--Up to Floor-V- Level

B/W (100B)-In Cement mortar 1:4 (1 cement : 4 coarse sand )-Half Brick masonary in foundation and Plinth

B/W (100B)-Extra for Half Brick masonary in superstructure above plinth up to V-Level

B/W (100B)-In Cement mortar 1:4 (1 cement : 4 coarse sand )-Half Brick masonary in superstructure above plinth up to V-Level

Providing and fixing Steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with ooden

Flooring Works- Cement concrete flooring (1:2:4)-- 40mm thick with 20 mm nominal size stone aggregate sqm

Kota Stone Slab flooring over 20mm (Average) thick base laid over and jointedwith..…. With Cement mortar (1:4)…... (20 to 25mmthick)

Kota Stone Slab flooring 20mm thick rises of steps skirting , Dado and pillars laid on 12mm (average ) thick with...…. With Cement mortar (1:3)…... (20 to 25mmthick)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3---

Providing and laying Glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4--

Providing and laying Glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in shades except white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4--

Providing designation-100 A -One Brick Flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building pecification and direction of E/l,

Providing designation-100 A -One Brick on Edge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building pecification and direction of E/l,

Providing designation-100 B -One Brick Flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building pecification and direction of E/l,

Providing designation-100 B -One Brick on Edge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building pecification and direction of E/l,

12mm Thick Cement Plaster of Mix (1:3)

12mm Thick Cement Plaster of Mix (1:4)

12mm Thick Cement Plaster of Mix (1:6)

15mm Thick Cement Plaster of Mix (1:6)- in Rough side

20mm Thick Cement Plaster of Mix (1:3)

20mm Thick Cement Plaster of Mix (1:4)

Cement Plaster with a Floating Coat of Neat Cement--12mm Thick Cement Plaster of Mix (1:3)

18mm CP in two coat under layer 12mm Thick Cement Plaster of Mix (1:5) and a top layer 6mm thick CP (1:6)

6mm Thick Cement Plaster of Mix (1:4) in Ceiling

Neat Cement Punning

Ghorasahan

ANALYSED RATE (BASIC RATE)

CARRIAGE COST

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :

metre

Supplying and Filling in plinth with local sand and under floors including watering, ramming consolidating and dressing complete.

Providing designation 100A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying in position specified Mix of reinforced cement concrete excluding the cost of centring,shuttering.finishing and reinforcement-All work puto plinth level 1:1:5:3(1 cement:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (anythickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finisnin and reinforcement 1:1:5:3(1 cement:1.5 coarse sand.3 graded stone aggregate 20mm nominal size)

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 150, landings.balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level exdudingthe cost of centring, shuttering, finishing and reinforement with 1:1.5:3(1 cement:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size).

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete.

Brick work with bricks of class designation 100A in foundation and plinth in:

Extra for Brick work in superstructure above plinth level upto floor V Level

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. all complete.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

15mm cement plaster on the rough side of single or half brick wall of mix:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

E.E L.A.E.O, Work Div-1 BIHARSHARIF

DESCRIPTION

Providing and installing cast in situ single under reamed piles

S/Filing Local sand in Foundation&Plinth

100A one brick flat soling

Prov.RCC M20

All work from plinth level upto floor V level

Centering&shuttering

Column

Reinforcement for RCC work

100A Brick work in Cm 1:6 in F/p

Extra for Brick work in superstructure above plinth level

P& F M.S grills

Steel work welded in built up sections

15mm th. Cement Plaster

Water proof cement paint

Applying priming coat

synthetic enamel paint on wooden & steel

E.E L.A.E.O, Work Div-1 BIHARSHARIF

Description

Providing and fixing water closet squatting pan (Indian type W.C pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required:

Provding and fixing soil,waste and vent pipes

metre

Provding and fixing heel rest sanitary bend

Provding and fixing single equal plain junction of required degree with access door ,insertion rubber washer 3mm thick ,bolt and nuts complete

Provding and fixing terminal guard

Providing and fixing on wall face unplasticised-PVC (working pressure 4 Kgf per sqm) rain water pipes conforming to IS:4985including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion

Metre

Providing and fixing on wall face unplasticised -PVC moulded fittings/ accessories for unplasticised PVC rainwater pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S screws of required length including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Excavating trenches of required width for pipes, cables etc including excavation for sockets and dressing of sides, ramming of bottoms depth upto 1.5m ,including getting out the excavated soil , and then returning the soil as required,in the layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming watering and desposing of surplus excavated soil as dirceted within a lead of 50m

pipes cables etc exceeding 80mm dia but not exceeding 300 mm dia

India mark-II Hand Pump with all accessories including 8 Nos. (3 Mtr length each) connecting rod and one syllinder Confirming IS: 155000 (Part 1-8)/2008

125 mm dia UPVC Casing Pipe confirming to IS : 12818-1983/1992

32 mm dia medium quality G.I. Riser Pipe and 8 Nos. 3 mtre length (3 mtr each length confirming IS:1239

40 mm dia x 2 mtr, long UPVC RIBEED Strainer confirming to IS : 12818 - 1983/1992

125 mm dia x 40 mm x UPVC reducing socket (Heavy Quality)

40 mm nominal outer dia CPVC Pipe

Supplying all materials labours and equipement for constructing platform with foot rest etc. all complete job.(Detail Est attached)

Supplying drain 3 m as per design etc. all complete job.(Detail Est Attached)

Boring by jet dheki by suitable cutter or reduce as the case may be lowering 125 mm UPVC x 40 mm dia G.I. Pipe & Strainer of standard quality iron shoe, plug & socket etc. all complete including providing all tools and oplants required for the job as per sopecification and direction of the engineer in charge.

Supplying labour and equipment including 125 mm dia G.I. cap & fitting and fixing over the T/W properly and taking it out as per direction of E.I. (Cap will be property of the contractor) 1 No.

Providing all labours for fitting and fixing of India mark II hand pump including supplying all tools and plants requred for the all job complete as per direction of E/I.

Supplying all tools equipment all labours for lowering 32 mm dia medium quality G.I. Pipe (Riser pipe) in drilled T/W in 3 mtrs lenth

Providing all labour for fitting and fixing of deep cylinder with the riser pipe including necessary connecting and jointing materials, chrom leather bucket all tools & plants required for the job low water lever all complete job as per specification and direction of E/I.

Supplying all materials & labours for arrangement of additional water required during the drilling work all complete job as per specification and direction of E/I.

Developing and t Testing of T/W till the discharge is free from sand one item all complete job as per specification and direction of E/I.

Providing earth work in excavation

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing P.C.C(1:2:4) in F&P ……do….do…..all complete job

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20 m,m nominal size)

Providing 100A B/W(1:4) in superstructure etc. all complete job.

Providing M-S reinfrocement etc .all complete job.

Providing 12mm thcik CP(1:4) on overall roof surface

50 mm size brick aggrigate outer side of soak pit

Point

Point

Point

Meter

E.E L.A.E.O, Work Div-1 BIHARSHARIF

Description

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m

Earth work in excavation in foundation trendies or drains( not excoding 1.5 m in width or ten sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m. Including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead.

Supplying and filling in plinth with local sand and under floors including, watering, ramming, consolidating and dressing complete.

1:2:4(1 Cement:3 coarse sand: 6 graded stone aggregate 20mm nominal size)

1:4:8(1 Cement:4 coarse sand: 8 graded stone aggregate 20mm nominal size)

Foundations, footings, bases of columns, etc. for mass concrete.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4{1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water profing material in cement concrete work in the proportion recommended by the manufacturers.

Providing and laying in position machine batched and mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved desing mix, Including pumping of concrete to site fo laying but excluding the cost of centering, shuttering, finishing an including retard setting of concrete, Improve workability withoutt impairing strength and admixtures in recommended proportions as per 15:9103to accelerate, reinforcement, durability as per direction of Engineer-incharge, Note:- Cement content considered in this item is @ 330kg/cum, Excessor less cement used as per design mix is payable or recoverable separetely.

Suspended floors, roofs, landings, balconies and access platform.

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Under 20cm wide

Weather shade, Chajjas, corbels, etc. including edges.

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-6mm dia

Thermo-Mechanically Treated bars TMTC-500-8mm dia

Thermo-Mechanically Treated bars TMTC-500-10mm dia

Thermo-Mechanically Treated bars TMTC-500-12mm dia

Thermo-Mechanically Treated bars TMTC-500-16mm dia

Cement mortar 1:6(1 cement:6 coarse sand) B/W ins/s

Extra for Brick work in superstructure above plinth level upto floor V Level

Brick work 7cm thick with F.P.S brick of class designation 100A in cement mortar 1:3(1 cement: 3 coarse sand) in superstructure.

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Extra for half Brick masonry in superstructure above pinth level upto floor V level.

Extra for providing and placing in position 2 nos. 6mm dia, MS bars at every third course of half brick masonry (with F.P.S bricks)

Providing wood work in frames of doors,windows, clerestory windows and other frames, wrought framed and fixed in position

35 mm thick factory made Solid panel PVCDoorshutter, made out of single piece extruded soild PVCprofiles, 5 mm (±0.2 mm) thick, having styles & rails (except lock rail) of size 95mmx35 mm x5 mm,out of which 75 mm shall be flat and 20 mmshall be tapered (on both side), having one side thickness of 15 mmintegrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MStube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVCsolvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing

25 mm thick non decorative flush door shutter paraper

25 mm thick (for cub-board) including nickel plated bright finished M.S.piano hinges with necessary screws

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers including necessary screws etc. complete.(best make of approved quality) 40 mm

Providing and fixing aluminium sliding door bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium handles anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing Alluminium hanging floor door stoper

Providing and fixing bright finished brass 100mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS:1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing and fixing aluminium tee chanals(heavy duty)with rollers,stop end in pelmets as curtain rod i

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitred and welded with 15x3mm lugs, 10cm long, with steel lugs embedded in cement concrete blocks 15x10x10cm of 1:3:6( 1 cement: 3 coarse sand: 6 complete including applying a priming coat of approved steel primer, excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Extra for providing and fixing steel beading of approved shape and section with screw instead of glazing clips and metal sash putty in steel doors, windows, ventilators and composite units.

Steel windows

Steel ventilators

Providing and fixing pressed steel door confirming IS code 351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Providing and fixing circular cast iron box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one ;pcf at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing bright finished brass casement window fastners of minimum weight 200 gms to side hung steel windows with necessary welding and machine screws etc. complete.

Providing and fixing bright finished brass peg stays 300mm long of minimum weight 330 gms. to side hung steel windows with necessary welding and machine screws etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement 18 mm thick

Providing and fixing glass strips in joints of terrazo/cement concrete floors.40 mm wide and 4 mm thick

Providing and laying Ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brow laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement: 4 Coarse sand) including pointing the joints with white cement and matching pigments etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622(thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing designation 100A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Providing average 150mm thick dry rammed khoa beaten to 112mm (compacted with water) made of well burnt or jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1: 10) all complete as per building specification and direction of E/l,

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4( 1 cement: 2 coarse sand: 4 graded stone aggregate of 20mm nominal size) over P.V.C sheet 1mx1mx400 micron, finished with 12mm cement plaster 1:3(1 cement: 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

1:6(1 cement: 6 coarse sand)

1:6(1 cement: 6 course sand)

1:4(1 cement: 4 course sand)

1:4( 1 cement: 4 coarse sand)

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of neat cement

New work (three or more coats)

New work (three or more coats)

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

With ready mixed red oxide zinc chromate yellow primer of approved brand and manufacture on steel galvanised iron/steel works

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Forming groove of uniform size from 12x12mm and upto 25x15mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Providing and laying cement based water proofing treatment over tertace

Providing 15 mm th Rcc pilinth level Band Level.

Providign 100A BIW(1:4) in superstructure etc. all complete job.

12 mm plaster 1:3 with cement punning

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Fixed to openings / wooden frames with rawl plugs screws etc.

Wiring for light point/ fan point/ exhaust fan point / call bell point with 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit with piano type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq mm FR PVC insulated copper conductor single core cable etc as required. Group- B a. Light/ call bell points - 27 b. Ceiling fan points - 07 c. Ex. Fan points - 02 Total - 36

Supplying and fixing 3 pin 5/6 amps socket outlet & 6A switch piano type on the existing switch box including connections etc. as required.

Supplying and fixing suitable size GI/PVC box on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outlet & 6A switch piano type connection painting etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade copper conductor PE insulated, with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing piano type T.V antenna socket on the existing metal box including making connection, etc. as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required.

Meter

Meter

Supplying and fixing metal box of following size in recess with suitable size of phenolic laminated sheet cover in the front including painting etc. as required.

Supplying and fixing 8 way double door sinle pole and Neutral sheet steel M.C.B. D.B, 240 Volts in recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar , detachable gland plate, interconnection, phosphatized and powder painted including nting, earthing etc. as required ( But without MCB/ RCCB/Isolator)(UPS DB)

Supplying and fixing of following rating C series MCB suitable for inductive and other loads of following poles in the existing MCB DB complete witth connections ,testing and commissioning etc. as required .

6 Amp. To 32 Amp. SP MCB 240 Volt

32 Amp SPN MCB 240 Volt

Earthing with G.I earth pipe 4.5 mt. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. including providing salt and charcoal for pipe earth electrode as required.

Providing and laying earth connections from earth electode with 4.00 mm. Dia copper wire in 15 mm. Dia G.I.pipe from earth electrode as required.

Providing and fixing 25mmX5mm GI strip on surface for connection etc as required.

Providing and fixing 4mm dia copper wire on surface or in recess for loop earthing etc as required.

Supplying and fixing bulkhead fitting die cast aluminium alloy body with prismatic glass cover suitable for the GLS/CFL lamp directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable etc. as required.

Supplying and fixing 2 pin 5 Amp ceiling rose on the existing junction box/ PVC box including connection etc as required.

Supplying and fixing batten / angle holder including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable etc. as required.

Supplying and fixing following types lamp in existing electrical fitting/ fixture etc as required.

Supplying and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep including wiring the down rods of stanard length ( upto 30 cm) with 1.5 sq. mm FR PVC insulated insulated copper conductor etc as required.

Supply and Installation of 300 mm, 230 V A.C. exhaust fan in the existing opening, including making good the damage, including making good the damage, connection, testing, commissioning etc. as required.

Supplying and fixing powder coated strip fitting complete with electronic ballast, 4'x40 watt fluorescent lamp etc. directly on ceiling / wall including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable etc. as required.

Providing and fixing water closet squatting pan (Indian type W.C pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests.

Provding and fixing soil,waste and vent pipes

metre

Provding and fixing heel rest sanitary bend

Provding and fixing single equal plain junction of required degree with access door ,insertion rubber washer 3mm thick ,bolt and nuts complete

Provding and fixing terminal guard

Providing and fixing on wall face unplasticised-PVC (working pressure 4 Kgf per sqm) rain water pipes conforming to IS:4985including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion

Metre

Providing and fixing on wall face unplasticised -PVC moulded fittings/ accessories for unplasticised PVC rainwater pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

110mm bend

110mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S screws of required length including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Excavating trenches of required width for pipes, cables etc including excavation for sockets and dressing of sides, ramming of bottoms depth upto 1.5m ,including getting out the excavated soil , and then returning the soil as required,in the layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming watering and desposing of surplus excavated soil as dirceted within a lead of 50m

Providing and laying non -pressure NP2 class(light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 including testing of joints etc. complete

Constructing brick masonary manhole in cement mortar 1:4 (1 cement, 4 coarse sand.) R.C.C. top slab with1:2:4 mix(1 cement, 2 coars e sand, 4 graded stone aggregate 20 mm nominal size) foundation cocrete 1:4:8 mix (1cement, 4 coarse sand, 8 graded stone aggregate 40 mm nominal size.) inside plastering 12 mm thick with cement mortar 1:3 (1 cement, 3 coarse sand.) finished with floating coat of neat cement and making channels in cement concrete 1:2:4. finished with floating coat of neat cement complete as per standard design.

Constructing soak pit 1.20x1.20x1.20 filled with brick bats including S.W.drain pipe 100 mm diameter and 1.20 m long complete as per standard design

India mark-II Hand Pump with all accessories including 8 Nos. (3 Mtr length each) connecting rod and one syllinder Confirming IS: 155000 (Part 1-8)/2008

125 mm dia UPVC Casing Pipe confirming to IS : 12818-1983/1992

32 mm dia medium quality G.I. Riser Pipe and 8 Nos. 3 mtre length (3 mtr each length confirming IS:1239

40 mm dia x 2 mtr, long UPVC RIBEED Strainer confirming to IS : 12818 - 1983/1992

125 mm dia x 40 mm x UPVC reducing socket (Heavy Quality)

40 mm nominal outer dia CPVC Pipe

Supplying all materials labours and equipement for constructing platform with foot rest etc. all complete job.(Detail Est attached)

Supplying drain 3 m as per design etc. all complete job.(Detail Est Attached)

Boring by jet dheki by suitable cutter or reduce as the case may be lowering 125 mm UPVC x 40 mm dia G.I. Pipe & Strainer of standard quality iron shoe, plug & socket etc. all complete including providing all tools and oplants required for the job as per sopecification and direction of the engineer in charge.

Supplying labour and equipment including 125 mm dia G.I. cap & fitting and fixing over the T/W properly and taking it out as per direction of E.I. (Cap will be property of the contractor) 1 No.

Providing all labours for fitting and fixing of India mark II hand pump including supplying all tools and plants requred for the all job complete as per direction of E/I.

Supplying all tools equipment all labours for lowering 32 mm dia medium quality G.I. Pipe (Riser pipe) in drilled T/W in 3 mtrs lenth

Providing all labour for fitting and fixing of deep cylinder with the riser pipe including necessary connecting and jointing materials, chrom leather bucket all tools & plants required for the job low water lever all complete job as per specification and direction of E/I.

Supplying all materials & labours for arrangement of additional water required during the drilling work all complete job as per specification and direction of E/I.

Developing and t Testing of T/W till the discharge is free from sand one item all complete job as per specification and direction of E/I.