Rectification of miscellaneous Daily Complaints Related to Plumbing, Masonry, Sanitary, Carpentry etc. on a Daily Basis in Bokaro Steel City Township

consolidating each deposited layer by ramming and watering, lead up

to 50 m and lift up to 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by

mechanical transport up to a lead of 5 km, also including ramming

and watering of the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc., complete.

Supplying and filling in plinth with sand under floors, including

watering, ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush

wood, trees and saplings of girth up to 30 cm measured at a height of

1 m above ground level and removal of rubbish up to a distance of

50m outside the periphery of the area cleared.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL

anti- termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @

one litre per hole, 300 mm apart including drilling 12 mm diameter

holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse

sand) to match the existing floor :

6 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. sqm 500.00 301.68 150839.33

Treatment of existing masonry using chemical emulsion @ one litre

per hole at 300 mm interval including drilling holes at 45 degree and

plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to

the full depth of the hole :

7 2.35.4.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. nos 2500.00 41.84 104597.50

Treatment at points of contact of wood work by chemical emulsion

Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5

litres per hole by drilling 6 mm dia holes at downward angle of 45

degree at 150 mm centre to centre and sealing the same.

Extra for levelling & neatly dressing of disposed soil completely as

directed by Engineer-in-Charge.

Reinforced Concrete work

1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural

10 4.1.3 sources : 4 graded stone aggregate 20 mm nominal size derived from cum 100.00 7665.78 766578.05

natural sources)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural

11 4.1.5 sources : 6 graded stone aggregate 20 mm nominal size derived from Cum 400.00 7097.74 2839097.24

natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs

having slope up to 15° landings, balconies, shelves, chajjas, lintels,

bands, plain window sills, staircases and spiral stair cases above

5.3 plinth level up to floor five level, excluding the cost of centering, cum 100.00 11194.85 1119485.15

shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5

coarse sand(zone-III) derived from natural sources : 3 graded stone

aggregate 20 mm nominal sizederived from natural sources).

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Reinforced cement concrete work in walls (any thickness), including

attached pilasters, buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and struts etc. above plinth

level up to floor five level, excluding cost of centering, shuttering,

finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural

1 5.2.2 sources : 3 graded stone aggregate 20 mm nominal size derived from cum 95.00 10559.92 1003192.43

natural sources)

Centering and shuttering including strutting, propping etc. and

removal of form for :

5.9.3 Suspended floors, roofs, landings, balconies and access platform.

3 5.9.4 Shelves (Cast in situ) sqm 300.00 902.21 270664.28

4 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 100.00 716.52 71651.72

5 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 125.00 935.34 116918.11

5.9.16 Edges of slabs and breaks in floors and walls, Under 20 cm wide

6 5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm 200.00 925.42 185084.06

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse

sand(zone-III) : 4 graded stone aggregate 6mm nominal size ),

reinforced with 1.6 mm dia mild steel wire, including centering and

shuttering, roughening cleaning, fixing and finishing in cement

mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding

plastering of the jambs, sills and soffits.

Steel reinforcement for R.C.C. work including straightening, cutting,

5.22A bending, placing in position and binding all complete upto plinth

8 5.22A.2 Hard drawn steel wire Kg 1000 93.21 93213.40

9 5.22A.6 Thermo Mechanically Treated bars of grade Fe-500D or more kg 8000.00 104.94 839504.40

Add for plaster drip course/ groove in plastered surface or moulding

to R.C.C. projections.

6.1 Brick work with F.P.S. bricks of class designation 75 in foundation and

11 6.1.1 Cement mortar 1:4 (1 cement: 4 coarse sand) cum 40.00 7171.64 286865.70

Brick work with clay flyash F.P.S. (non modular) brick of class

6.32 designation 7.5 in superstructure above plinth level up to floor five

12 6.32.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 250.00 8849.48 2212370.91

Brick work with modular extruded brunt fly ash clay sewer bricks

6.36 (Conforming to IS: 4885 ) in cement mortar 1:4 (1 cement : 4 coarse

sand) in foundation and plinth :

13 6.36.1 Cement Mortar 1:4 ( 1 cement : 4 coarse sand) cum 50.00 7003.41 350170.54

Half brick masonry with non modular fly ash bricks of class

6.45 designation 10, conformingio IS :12894, in super structure above

plinth and upto floor V level.

14 6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) sqm 300.00 1075.94 322783.02

Providing and fixing 18mm thick gang saw cut ( premoulded and

prepolished) machine cut for kitchen platforms, vanity counters,

window sills, facias and similar locations of required size of approved

shade, colour and texture laid over 20mm thick base cement mortar

8.2 1:4 (1 cement : 4 coarse sand) with joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing,

curing, moulding and polishing to edge to give high gloss finish etc.

complete at all levels.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black

8.2.2 Granite stone slab colour black, Cherry/Ruby red

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Extra for fixing marble /granite stone, over and above corresponding

17 8.4 basic item, in facia and drops of width upto 150 mm with epoxy resin meter 100.00 553.20 55319.92

based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash

basin/kitchen sink in kitchen platform, vanity counter and similar

18 8.5 location in marble/ Granite/ stone work, including necessary holes nos 60.00 952.28 57136.51

for pillar taps etc. including moulding, rubbing and polishing of cut

edges etc. complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to

IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge, in skirting, risers

of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1

cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed with pigment of

matching shade complete

Designing, fabricating, testing, installing and fixing in position Curtain

Wall with Aluminium Composite Panel Cladding, with open grooves

for linear as well as curvilinear portions of the building , for all

heights and all levels etc. including:

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required dia & length

(hold fast lugs or dash fastener shall be paid for separately).

21 9.1.1 Second class teak wood Cum 10.00 139090.06 1390900.58

Providing and fixing panelling or panelling and glazing in panelled or

panelled and glazed shutters for doors, windows and clerestory

9.7 windows (Area of opening for panel inserts excluding portion inside

grooves or rebates to be measured). Panelling for panelled or

panelled and glazed shutters 25 mm to 40 mm thick.

9.7.7 Float glass panes

23 9.7.7.1 4 mm thick glass pane (weight not less than 10 kg/sqm). sqm 100.00 2181.27 218127.14

24 9.7.7.2 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). sqm 50.00 2530.24 126511.89

Providing and fixing glazed shutters for doors, windows and

clerestory windows using 4 mm thick float glass panes (weight not

less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt

hinges bright finished of required size with necessary screws.

9.9.1 Second class teak wood

9.16 Providing and fixing 25 mm thick shutters for cup board etc.

9.16.1 Panelled or panelled & glazed shutters

Second class teak wood including ISI marked nickel plated bright

finished M.S. piano hingeswith necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board construction

9.21 with frame of 1st class hard wood and well matched commercial 3

ply veneering with vertical grains or cross bands and face veneers on

both faces of shutters:

30 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm

28 9.23 minimum depth on all edges of flush door shutters (over all area of Sqm 1200.00 449.87 539839.86

door shutter to be measured).

Providing and fixing nickel plated M.S. pipe curtain rods with nickel

plated brackets :

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing M.S. grills of required pattern in frames of

9.48 windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete.

30 9.48.1 Fixed to steel windows by welding kg 240.00 213.18 51164.23

31 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. kg 240.00 231.91 55659.49

32 9.51.2 With 12 mm mild steel U beading sqm 160.00 913.84 146214.66

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to

frame with 10 mm diameter bolts, nuts and wooden plugs and

33 9.53 embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 Each 1000.00 222.67 222671.05

cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal

Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges

bright finished with necessary screws etc. complete :

Providing and fixing oxidised M.S. hasp and staple (safety type)

9.67 conforming to IS : 363 with necessary screws etc. complete (Copper

oxidised as per IS 1378)

Providing and fixing oxidised M.S. casement stays (straight peg type)

with necessary screws etc. complete (Copper oxidised as per IS 1378)

41 9.68.1 300 mm weighing not less than 330 grams No 500.00 65.58 32790.10

42 9.68.2 250 mm weighing not less than 280 grams Nos 200.00 59.40 11880.33

9.76 Providing and fixing bright finished brass 100 mm mortice latch and

43 lock with 6 levers and a pair of lever handles of approved quality with Each 100.00 831.57 83157.45

necessary screws etc. complete.

9.82 Providing and fixing bright finished brass hanging type floor door

stopper with necessary screws, etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch

45 9.88 and lock with 6 levers and a pair of lever handles of approved quality Nos 120.00 971.39 116567.35

with necessary screws etc. complete.

Providing and fixing chromium plated brass 50 mm cupboard or

wardrobe knobs with nuts complete.

Providing and fixing chromium plated brass handles with necessary

screws etc. complete:

Providing and fixing aluminium sliding door bolts ISI marked anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade with nuts and

screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised

(anodic coating not less than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or shade with necessary

screws etc. complete :

Providing and fixing aluminium pull bolt lock, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed of required colour and shade, with necessary

screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles of approved make anodized

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade with necessry

screws etc. complete.

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing aluminium hanging floor door stopper ISI marked

anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour and shade with necessary

screws etc. complete.

57 9.101.1 Single rubber stopper Each 1500.00 38.53 57796.20

Providing and fixing factory made uPVC door frame made of uPVC

extruded sections having an overall dimension as below (tolerance

±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door

frame to be Jointed with galvanized brackets and stainless steel

screws, joints mitred and Plastic welded. The hinge side vertical of

the frames reinforced by galvanized M.S. tube of size 19 X 19 mm

58 9.117.1 Extruded section profile size 48x40 mm Rmt 396.00 262.90 104110.22

9.118 Providing and fixing to existing door frames.

24 mm thick factory made PVC door shutters made of styles and rails

of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm

(± 0.2 mm) with inbuilt edging on both sides. The styles and rails

mitred and joint at the corners by means of M.S. galvanised/ plastic

9.127 Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt / suede finish with high density protective

surface layer and reverse side of adhesive bonding quality

conforming to IS : 2046 Type S, including cost of adhesive of

Providing and fixing factory made Fiberglass Reinforced Plastic

(F.R.P.) Chhajja 4mm thick of required colour size and design made of

Resin Transfer moulding (RTM)Machine technology, resulting in void

free compact laminate in single piece, having smooth gradual slope

9.140 Providing and fixing plain lining with necessary screws/nuts &

bolts/nails including a coat of approved primer on one face and fixed

on wooden /steel frame work, complete as per direction of Engineer-

in-charge. (Frame work shall be paid for separately)

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type.

Providing and fixing factory made uPVC glazed/wire mesh

windows/doors comprising of lead free uPVC multi-chambered

frame, sash and mullion/coupler (where ever required) extruded

profiles having minimum wall thickness of 1.70 mm for Series R1 and

R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to

EN: 12608 in any shape, colour and design duly reinforced with

galvanized mild steel section made of required shape & size as per

CPWD Specification, uPVC extruded glazing beads, interlocks and

9.147A Inline sash adaptor (where ever required) of appropriate dimension,

EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm

dia with countersunk head, comprising of matching polyamide PA6

grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to

14, plastic packers, plastic caps and necessary stainless steel screws

etc. Profile of frame, sash & mullion (if required) shall be mitred cut

and fusion welded/mechanically jointed duly sealed at all corners,

including drilling of holes for fixing hardware and drainage of water

After fixing frame the gap between frame and adjacent finished wall

shall be filled with weather proof silicon sealant over backer rod pf

approved size and quality, all complete as per approved drawing

conforming to CPWD specification & direction of Engineer-in-Charge.

Section of steel reinforcement and cross sections of uPVC profiles to

be as per design approved by Engineer-in-Charge. Wire mesh /

Glazing of plain/ toughened/ laminated/ double glass unit with /

without high performance coatings as per design requirements and

conforming to IS: 3548 & IS:16231 shall be paid separately.

Note:- Structural design proof checked from a Government

Engineering Institute, to be provided by the manufacturer for:

(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3

(ii) Sites with structure height more than 20m for all wind speeds.

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Two track two panels sliding window with Aluminium channel for

roller track, wool pile, nylon rollers with SS 304 body.

Using R2 series with frame (40mm & above) x (40mm & above) &

63 9.147.A1.1 sash (25mm & above) x (50mm & above) with zinc alloy (zamak) sqm 100.00 8074.78 807478.11

powder coated touch locks with hook (Height upto 1.2 meter)

Ventilator Casement window single panel with or without fixed panel

9.147.D1 with S S. 304 friction hinges as per size and weight of sash, single

point locking zinc alloy (zamak) powder coated handles.

Using R1 series with frame (33mm & above ) x (35mm & above) &

64 9.147.D1.1 sash /mullion (33mm & above) x (50 mm & above). (Height upto 0.90 sqm 100.00 12844.77 1284476.76

Casement window single panel with S.S. 304 friction hinges as per

9.147.E1 size and weight of sash, multi-point locking system, zinc alloy (zamak)

powder coated handles.

Using R2 series with frame (39mm & above) x (39mm & above) &

sash (39mm & above) x (60mm & above). (Height upto 1.2 meter)

Providing and fixing bright /matt finished Stainless Steel handles of

approved quality & make with necessary screws etc all complete.

Providing and fixing factory made ISI marked steel glazed doors,

windows and ventilators, side /top /centre hung, with beading and

all members such as F7D, F4B, K11 B and K12 B etc. complete of

standard rolled steel sections, joints mitred and flash butt welded

and sash bars tenoned and riveted, including providing and fixing of

69 10.11.1 hinges, pivots, including priming coat of approved steel primer, but kg 1000.00 127.49 127492.19

excluding the cost of other fittings, complete all as per approved

design, (sectional weight of only steel members shall be measured

for payment). Fixing with 15x3 mm lugs 10 cm long embedded in

cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing & fixing glass panes with putty and glazing clips in steel

70 10.30.1 doors, windows, clerestory windows all complete with : 4.0 mm thick sqm 1000.00 1035.90 1035904.45

Providing and fixing T-iron frames for doors, windows and ventilators

of mild steel Tee-sections, joints mitred and welded, including fixing

of necessary butt hinges and screws and applying a priming coat of

approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

71 10.13.1 block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded kg 1000.00 137.87 137874.10

stone aggregate 20 mm nominal size).

Welding by gas or electric plant including transportation of plant at

site etc. complete.

Providing and fixing stainless steel ( Grade 304) railing made of

Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories & stainless

steel dash fasteners , stainless steel bolts etc., of required size, on

the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-incharge, (for payment

purpose only weight of stainless steel members shall be considered

excluding fixing accessories such as nuts, bolts, fasteners etc.).

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Brick on edge flooring with bricks of class designation 7.5 on a bed of

11.1 12 mm cement mortar, including filling the joints with same mortar,

with common burnt clay non modular bricks:

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate) finished with a floating coat of neat cement,

including cement slurry, but excluding the cost of nosing of steps etc.

75 11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 1000.00 597.62 597616.60

Chequerred precast cement concrete tiles 22 mm thick in footpath

&courtyard, jointed with neat cement slurry mixed with pigment to

11.2 match the shade of tiles, including rubbing and cleaning etc.

complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4

76 11.20.1 Light shade pigment using white cement. sqm 50.00 1364.15 68207.30

77 11.20.2 Medium shade pigment using 50% white cement 50% Grey cement. sqm 50.00 1292.48 64624.23

78 11.20.3 Dark shade pigment using ordinary cement. sqm 50.00 1089.27 54463.68

79 11.20.4 Ordinary cement without any pigment. sqm 50.00 1027.83 51391.43

Providing and laying rectified Glazed Ceramic floor tiles of size

300x300 mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS : 15622, of approved

make, in all colours, shades, except White, Ivory, Grey, Fume Red

Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse

sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

pointing the joints with white cement and matching pigments etc.,

Providing and laying Vitrified tiles in floor in different sizes (thickness

to be specified by the manufacturer) with water absorption less than

0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid on 20 mm thick cement

mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry

@3.3 kg/sqm including grouting the joints with white cement and

matching pigments etc. The tiles must be cut with the zero chipping

diamond cutter only . Laying of tiles will be done with the notch

trowel, plier, wedge, clips of required thickness, leveling system and

rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

Providing corrugated G.S. sheet roofing including vertical / curved

surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm

diameter with bitumen and G.I. limpet washers or with G.I. limpet

washers filled with white lead, including a coat of approved steel

primer and two coats of approved paint on overlapping of sheets

complete (up to any pitch in horizontal/ vertical or curved surfaces),

excluding the cost of purlins, rafters and trusses and including cutting

to size and shape wherever required.

83 12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m* sqm 400.00 1417.81 567122.78

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A, including jointing with seal

ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming

85 12.42.4.2 to IS : 13592 Type A, including jointing with seal ring conforming to IS Each 500.00 215.37 107686.78

: 5382, leaving 10 mm gap for thermal expansion:Single tee with door

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing unplasticised -PVC pipe clips of approved design

to unplasticised - PVC rain water pipes by means of 50x50x50 mm

hard wood plugs, screwed with M.S. screws of required length,

including cutting brick work and fixing in cement mortar 1:4 (1

cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming

87 12.42.5.2 to IS : 13592 Type A, including jointing with seal ring conforming to IS Each 500.00 146.29 73145.28

: 5382, leaving 10 mm gap for thermal expansion:Bend 87.5° 110 mm

Providing and fixing on wall face unplasticised - PVC moulded

fittings/accessories for unplasticised Rigid PVC rain water pipes

88 12.42.6.2 conforming to IS : 13592 Type A, including jointing with seal ring Each 300.00 128.29 38487.02

conforming to IS : 5382, leaving 10 mm gap for thermal

expansion:Shoe (Plain) 110 mm Shoe

Providing and fixing false ceiling at all height including providing and

fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both

side inclusive) as per IS : 277 and consisting of angle cleats of size 25

mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200

mm centre to centre, one flange fixed to the ceiling with dash

12.45 fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange

of cleat fixed to the angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running

at the spacing of 1200 mm centre to centre, to which the ceiling

section 0.5 mm thick bottom wedge of 80 mm with tapered flanges

of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,

shall be fixed in a direction perpendicular to G.I. intermediate

channel with connecting clips made out of 2.64 mm dia x 230 mm

long G.I. wire at every junction, including fixing perimeter channels

0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long,

the perimeter of ceiling fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x 25

mm at 230 mm c/c, including jointing and finishing to a flush finish of

tapered and square edges of the board with recommended jointing

compound , jointing tapes , finishing with jointing compound in 3

layers covering upto 150 mm on both sides of joint and two coats of

primer suitable for board, all as per manufacturer's specification and

also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably

fixed, all complete as per drawings, specification and direction of the

Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS:

2095- (Part I) : 2011 (Board with BIS certification marks)

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing precoated galvanised iron profile sheets (size,

shape and pitch of corrugation as approved by Engineer-in-Charge)

of total coated thickness 0.50 mm (base metal of minimum 0.45 mm

thickness with total coating thickness of 0.05mm) with zinc coating

120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7

microns epoxy primer on both side of the sheet and polyester top

coat 15-18 microns. Sheet should have protective guard film of 25

microns minimum to avoid scratches during transportation and

should be supplied in single length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed using self drilling /seIf

tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved surfaces, excluding the cost

of purlins, rafters and trusses and including cutting to size and shape

wherever required.

13.1 12 mm cement plaster of mix :

15 mm cement plaster on the rough side of single or half brick wall of

13.16 6 mm cement plaster of mix :

94 13.18 Neat cement punning sqm 2700.00 77.79 210036.65

Rough cast plaster upto 10 m height above ground level with a

mixture of sand and gravel or crushed stone from 6 mm to 10 mm

nominal size, dashed over and including the fresh plaster in two

13.19 layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse

sand) and top layer 10 mm cement plaster 1:3 (1 cement: 3 fine

sand) mixed with 10% finely grounded hydrated lime by volume of

95 13.19.1 Ordinary cement finish using ordinary cement sqm 5000.00 862.66 4313309.00

Extra for providing and mixing water proofing material in cement of

plaster work in proportion recommended by the manufacturers. 50KG

13.37 White washing with lime to give an even shade:

97 13.37.1 New work (three or more coats) sqm 2000.00 38.00 75991.30

13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and

including priming coat of exterior primer applied @2.20kg/10 sqm.

13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and

99 13.46.1 including priming coat of exterior primer applied @ 0.90 litre/10 sqm 500.00 156.26 78131.90

13.5 Applying priming coat :

With ready mixed aluminium primer of approved brand and

manufacture on resinous wood and plywood.

With ready mixed red oxide zinc chromate primer of approved brand

and manufacture on steel galvanised iron/steel works

Providing and applying white cement based putty 1mm on plaster

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50

13.83 grams/ litre. of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and

Applying priming coats with primer of approved brand and

manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC

content less than 50 grams/litre.

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Removing white or colour wash by scrapping and sand papering and

105 13.88 preparing the surface smooth including necessary repairs to sqm 50000.00 19.22 960837.50

scratches etc. complete

Painting with synthetic enamel paint of approved brand and

106 13.99.1 manufacture of required colour to give an even shade : One or more sqm 3000.00 100.02 300073.20

coats on old work

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq.meters and under, including cutting the patch in proper shape,

raking out joints and preparing and plastering the surface of the walls

complete, including disposal of rubbish to the dumping ground, all

complete as per direc on of Engineer in-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand)

Fixing chowkhats in existing opening including embedding chowkhats

in floors or walls cutting masonry for holdfasts, embedding hold fasts

in cement concrete blocks of size 15 x 10 x 10 cm with cement

concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate

14.2 20 mm nominal size), painting two coats of approved wood

preservative to sides of chowkhats and making good the damages to

walls and floors as required complete, including disposal of rubbish

to the dumping ground, all complete as per directions of Engineer-In-

110 14.9 Renewal of old putty of glass panes (length) . meter 6000.00 54.63 327803.70

Pumping out water caused by springs, tidal or river seepage, broken

water mains or drains and the like.

Providing and fixing double scaffolding system (cup lock type) on the

exterior side, up to seven story height made with 40 mm dia M.S.

tube 1.5 m centre to centre, horizontal & vertical tubes joining with

cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps

and M.S. staircase system in the scaffolding for working platform etc.

and maintaining it in a serviceable condition for the required

duration as approved and removing it there after. The scaffolding

system shall be stiffened with bracings, runners, connection with the

building etc wherever required for inspectionof work at required

locations with essential safety features for the workmen etc.

complete as per directions and approval of Engineer-in-charge. The

elevational area of the scaffolding shall be measured for payment

purpose. The payment shall be made once irrespective of duration of

scaffolding.Note: - This item to be used for maintenance work

judicially, necessary deduction for scaffolding in the existing item to

Providing and fixing bright finished brass casement window fasteners

113 14.73 or peg stays to windows/ ventilators with necessary welding and kg 50.00 542.16 27107.78

machine screws etc. complete.

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5

sqm and under, including cutting the patch in proper shape, raking

out joints and preparing plastering the wall surface with white

cement based polymer modified self curing mortar, including

disposal of rubbish, all complete as per the direction of Engineer-In-

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Cleaning of terrace/loft water storage tank (inside surface area) upto

2000 litre capacity at all heights with coconut brushes, duster etc.,

removal of silt, rubbish from the tank and cleaning the tank with

fresh water disinfecting with bleaching powder @ 0.5gm per litre

capacity of tank, including marking the date of cleaning on the side of

tank body with the help of stencil and paint and disposing of malba,

115 14.75A all complete as per direction of Engineer-in-Charge. (The old date Ltr 240000.00 0.49 116760.00

already written on tank should be removed with paint remover or

black paint and if date is not written with the stencil or old date is

not removed deduction will be made @ Rs. 0.10 per litre if during

cleaning any GI fittings or ball cock is damaged that is to be repaired

by contractor at his own cost and nothing extra will be paid on this

Cleaning and de-silting of gully trap chamber, including removal of

116 14.76 rubbish mixed with earth etc. and disposal of same, all as per the No. 400.00 105.38 42150.36

direction of Engineer-in-charge.

Cleaning of under ground sump, Over Head R.C.C. Tank (independent

14.78 staging) including disposal of slit and rubbish, all as per direction of

Engineer-in-Charge. The cleaning shall consist following operations:-

(i) Tank shall be emptied of water by pumping & bottom shall be

cleaned of slit and other deposits.

(ii) Entire surface area of the sump shall then scrubbed thoroughly

with wire brush etc. and pressure washed with water.

(iii) Chlorination of RCC internal surface by liquid chlorine.

(iv) The treated surface shall be dried using air jetting and all loose

particles shall be removal from the surface.

(v) Finally the surface shall be treated with ultraviolet radiation etc.

as per direction of Engineer-in-Charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled

118 14.82 materials i/c malba all complete as per directions of Engineer-in each 40.00 130.48 5219.17

Dismantling 15 to 40 mm dia G.I. pipe including stacking of

dismantled pipes (within 50 metres lead) as per direction of Engineer

(a) Internal Work- Exposed on wall

Taking out existing wooden door shutter, repair by cutting, painting

etc. and refixing of repaired door shutters to existing door frames,

including replacement of hinges with screws, etc. as required, all

complete as per the direction of the Engineer-in-charge

Dismantling works

Demolishing cement concrete manually/ by mechanical means

121 15.2.2 including disposal of material within 50 metres lead as per direction cum 100.00 1463.00 146300.28

of Engineer - in - charge.

Demolishing R.C.C. work manually/ by mechanical means including

122 15.3 stacking of steel bars and disposal of unserviceable material within cum 100.00 3455.37 345536.63

50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including

stacking of serviceable material and disposal of unserviceable

material within 50 metres lead as per direction of Engineer-in-

Dismantling doors, windows and clerestory windows (steel or wood)

shutter including chowkhats, architrave, holdfasts etc. complete and

stacking within 50 metres lead

Of area 3 sq. metres and below.

Dismantling tile work in floors and roofs laid in cement mortar

124 15.23.1 including stacking material within 50 metres lead. sqm 160.00 71.42 11426.91

For thickness of tiles 10 mm to 25 mm

Dismantling barbed wire or flexible wire rope in fencing including

making rolls and stacking within 50 metres lead

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Dismantling C.I. or asbestos rain water pipe with fittings and clamps

126 15.42.2 including stacking the material within 50 metres lead : meter 4000.00 75.89 303576.00

Dismantling G.I. pipes (external work) including excavation and

refilling trenches after taking out the pipes, manually/ by mechanical

means including stacking of pipes within 50 metres lead as per

direction of Engineer-in-charge : 15 mm to 40 mm nominal bore

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

128 15.52 including stacking of useful materials near the site and disposal of each 40.00 109.02 4360.99

unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the

129 15.56 surface for plaster including disposal of rubbish to the dumping sqm 12000.00 53.17 638093.40

ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable,

dismantled or waste materials by mechanical means, including

130 15.6 loading, transporting, unloading to approved municipal dumping Cum 16000.00 256.82 4109173.60

ground or as approved by Engineer-in-charge, beyond 50 m initial

lead, for all leads including all lifts involved.

Fencing with angle iron post placed at required distance embedded

in cement concrete blocks, every 15th post, last but one end post

and corner post shall be strutted on both sides and end post on one

side only and provided with horizontal lines and two diagonals

16.18 interwoven with horizontal wires, of barbed wire weighing 9.38 kg

per 100 m (minimum), between the two posts fitted and fixed with

G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth

work and concrete work to be paid for separately). Payment to be

made per metre cost of total length of barbed wire used.

131 16.18.1 With G.I. barbed wire meter 10000.00 21.50 215033.00

Providing and fixing concertina coil fencing with punched tape

concertina coil 600 mm dia 10 metre openable length ( total length

90 m), having 50 nos rounds per 6 metre length, upto 3 m height of

wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart

and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with

132 16.53 G.I. staples and G.I. clips to retain horizontal, including necessary meter 2000.00 365.65 731306.80

bolts or G.I. barbed wire tied to angle iron, all complete as per

direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) /

Spring core (2.5mm thick) wire of high tensile strength of 165 kg/

sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost

of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying 60mm thick factory made cement concrete

interlocking paver block of M -30 grade made by block making

machine with strong vibratory compaction, of approved size, design

& shape, laid in required colour and pattern over and including

50mm thick compacted bed of coarse sand, filling the joints with fine

sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone

of M-25 grade cement concrete in position to the required line, level

and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse

sand), including making joints with or without grooves (thickness of

joints except at sharp curve shall not to more than 5mm), including

making drainage opening wherever required complete etc. as per

direction of Engineer-in-charge (length of finished kerb edging shall

be measured for payment). (Precast C.C. kerb stone shall be

approved by Engineer-in-charge).

Providing and fixing G.I. chain link fabric fencing of required width in

mesh size 25x25 mm made of G.I. wire of dia 3 mm including

strengthening with 2 mm dia wire or nuts, bolts and washers as

required complete as per the direction of Engineer-in-charge.

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and placing in position 100 mm thick factory made machine

batched & machine mixed Precast RCC Rectangular Covers on drains

of footpath of various sizes, of M-25 grade cement concrete for RCC

work, including cost of centering, shuttering, reinforcement of 8 mm

dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways ,

136 16.93 neat cement punning on finished surface, properly encased on all sqm 50.00 2998.74 149936.87

edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over

priming coat , reinforcement to be welded at edges with MS sheet

and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage,

all leads & lift, handling at site etc. all complete as per direction of

Engineer-in-Charge.

Aluminium works

Providing and fixing aluminium work for doors, windows, ventilators

and partitions with extruded built up standard tubular

sections/appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws

or with fixing clips, or with expansion hold fasteners including

necessary filling up of gaps at junctions, at top, bottom and sides

with required PVC/neoprene felt etc. Aluminium sections shall be

smooth, rust free, straight, mitred and jointed echanically wherever

required including cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge.

Glazing and paneling to be paid for separately) :

21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder coating 50

For shutters of doors, windows & ventilators including providing and

fixing hinges/ pivots and making provision for fixing of fittings

wherever required including the cost of EPDM rubber / neoprene

gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket etc.

21.3 complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid in

With float glass panes of 4.0 mm thickness (weight not less than 10

With float glass panes of 5 mm thickness (weight not less than 12.50

Providing and fixing double action hydraulic floor spring of approved

brand and manufacture conforming to IS : 6315, having brand logo

embossed on the body / plate with double spring mechanism and

door weight upto 125 kg., for doors, including cost of cutting floors

,embedding in floors as required and making good the same

matching to the existing floor finishing and cover plates with brass

pivot and single piece M.S. sheet outer box with slide plate etc.

complete as per the direction of Engineer-in-charge.

141 21.4.1 With stainless steel cover plate minimum 1.25 mm thickness. Nos 6.00 2747.61 16485.64

Providing and fixing 12 mm thick frameless toughened glass door

shutter of approved brand and manufacture, including providing and

fixing top & bottom pivot & double acting hydraulic floor spring type

fixing arrangement and making necessary holes etc. for fixing

required door fittings, all complete as per direction of Engineer-in-

charge (Door handle, lock and stopper etc. to be paid separately).

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and laying water proofing treatment in sunken portion of

143 22.5 WCs, bathroom etc., by applying cement slurry mixed with water

proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This layer will be

allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with

water proofing cement compound @ 0.126 kg/sqm. This layer will be

allowed to air cure for 4 hours followed with water curing for 48

(The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed sqm 300.00 600.39 180116.90

23.1 Boring/drilling bore well of required dia for Casing/ strainer pipe, by

suitable method prescribed in IS: 2800 (part I), including collecting

samples from different strata, preparing and submitting strata

chart/bore log, including hire & running charges of all equipments,

tools, plants & machineries required for the job, all complete as per

direction of Engineer –in-charge, upto 90 metre depth below ground

23.1.1 All types of soil

23.1.2 Rocky strata including Boulders

23..3 Supplying, assembling, lowering and fixing in vertical position in bore

well, unplasticized PVC medium well casing (CM) pipe of required dia,

conforming to IS: 12818, including required hire and labour charges,

fittings & accessories etc. all complete, for all depths, as per direction

of Engineer –in-charge.

23.6 Supplying, filling, spreading & leveling gravels of size range 4.6 mm Cu.M 10

to 4.8 mm, in the recharge pit, over the existing layer of boulders, in 1496.72 14967.17

required thickness, for all leads & lifts, all complete as per direction of

Engineer-in-charge.

23.5 Supplying, filling, spreading & leveling stone boulders of size range 5 Cu.M 50

147 cm to 20 cm, in recharge pit, in the required thickness, for all leads & 1469.04 73451.77

lifts, all complete as per direction of Engineer-in-charge.

23.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5

144 mm to 2 mm in recharge pit, in required thickness over gravel layer, 10.00 1496.72 14967.17

for all leads & lifts, all complete as per direction of Engineer –in-

Repair with New Technologies

Chipping of unsound/weak concrete material from slabs, beams,

columns etc. with manual Chisel and/ or by standard power driven

percussion type or of approved make including tapering of all edges,

148 26.28.1 making square shoulders of cavities including cleaning the exposed sqm 1000.00 367.79 367794.00

concrete surface and reinforcement with wire brushes etc. and

disposal of debris for all lead and lifts all complete as per direction of

Engineer-In-Charge. 75mm average thickness

Cleaning of reinforcement from rust from the reinforcing bars to give

it a total rust free steel surface by using alkaline chemical rust

remover of approved make with paint brush and removing loose

particles after 24 hours of its application with wire brush and

thoroughly washing with water and allowing it to dry, all complete as

per direction of Engineer-In-Charge.

Providing, mixing and applying bonding coat of approved adhesive on

26.31 chipped portion of RCC as per specifications and direction of

Engineer-In-charge complete in all respect.

SBR Polymer (@10% of cement weight) modified cementitious bond

26.31.1 coat @ 2.2 kg cement per sqm of surface area mixed with specified sqm 1500 137.39 206081.40

proportion of approved polymer

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Epoxy bonding adhesive having coverage 2.20 sqm/kg

of approved make

Fabrication and manufacturing of solid precast concrete element

with provisions of shear keys, connecting loops, dowel tubes and

proper lifting accessories for walls, beams, slabs, stairs, column etc,

of various thickness, shape and size of different concrete grades

manufactured in controlled factory environment with approved

methodology including moulds (Pallet system, Tilts form, table

moulds, battery moulds, vertical moulds, beam moulds, column

moulds, staircase moulds, Facade mould, etc.), mixing, transporting

and placing of concrete, vibrating, curing, finishing, making necessary

cutout/holes of required sizes for services, yard handling & stacking

all complete as per IS 11447:1985 and as per approved shop

drawings and design mix as per the direction of Engineer-in-Charge

(Cost of reinforcement, Mechanical, Electrical and Plumbing inserts

will be paid separately).

152 26.74.1 Concrete grade M-35 (Cement content 370 kgs) Cum 50 20363.63 1018181.26

Transportation of Precast Elements by flat bed Trailor (Double /

Triple axle 40ft Length with proper accessories like A frame etc) from

factory, including the cost of loading , unloading & stacking at site

with the help of required capacity cranes.

Erection & Installation of Precast/Prestressed Concrete elements in

correct & final position with proper line level and plumb at site

making all arrangements (i.e cranes, push-pull jacks & all another T &

P for lifting Placing & Alignment of elements, within erection

26.77 tolerance as per IS 15916 as per approved shop drawings and all

complete as per the direction of Engineer-in-Charge but excluding

the cost of sim pads, non shrink grout and steel works i.e hangers. All

work up to fifth floor.

154 26.77.3 Solid concrete wall elements Cum 50 2646.85 132342.60

Total civil works 110882362.4 -

Sanitary & Plumbing

Providing and fixing water closet squatting pan (Indian type W.C.pan

) with 100 mm sand cast Iron P or S trap, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with manually controlled

device (handle lever) conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making good the walls and

floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet

(European type W.C. pan) with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with manually controlled

device (handle lever), conforming to IS : 7231, with all fittings

andfixtures complete, including cutting and making good the walls

and floors wherever required :

156 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Nos 50.00 6339.63 316981.51

Providing and fixing CP Brass 32 mm size Bottle Trap of approved

quality & make and as per the direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as

per IS:13983 with C.I. brackets and stainless steel plug 40 mm,

including painting of fittings and brackets, cutting and making good

the walls wherever required:

17.10.1 Kitchen sink with drain board

17.10.2 Kitchen sink without drain board

Providing and fixing white vitreous china water closet squatting pan

(Indian type) :

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

160 17.13.2 Orissa pattern W.C. pan of size 580x440 mm Nos 100.00 3083.49 308348.57

Providing and fixing white vitreous china pedestal type (European

type/ wash down type) water closet pan.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1

162 17.16A metre long with S.S. triangular plate to Eureopean type W.C. of Nos 200.00 339.72 67944.59

quality and make as approved by Engineer - in - charge.

Providing and fixing a pair of white vitreous china foot rests of

standard pattern for squatting pan water closet :

Providing and fixing P.V.C. low level flushing cistern with manually

17.18 controlled device (handle lever) conforming to IS : 7231, with all

fittings and fixtures complete.

Providing and fixing solid plastic seat with lid for pedestal type W.C.

165 17.20.1 White solid plastic seat with lid Nos 250.00 666.36 166589.76

Providing and fixing white vitreous china wash basin including making

all connections but excluding the cost of fittings :

166 17.25.1 Flat back wash basin of size 630x450 mm. Nos 60.00 1303.53 78211.69

167 17.25.2 Flat back wash basin of size 550x400 mm. Nos 60.00 965.80 57947.99

168 17.25.3 Angle back wash basin of size 600x480 mm. Nos 30.00 1303.53 39105.84

169 17.25.4 Angle back wash basin of size 400x400mm. Nos 30.00 846.75 25402.60

170 17.25.5 Flat back wash basin of size 450x300 mm. Nos 30.00 610.07 18302.13

Providing and fixing P.V.C. waste pipe for sink or wash basin including

P.V.C. waste fittings complete.

17.28.2 Flexible pipe

172 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Nos 300.00 51.81 15543.68

Providing and fixing 600x450 mm beveled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers

Providing and fixing mirror of superior glass (of approved quality) and

of required shape and size with plastic moulded frame of approved

make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off,

supported on anodised aluminium angle frame with C.P. brass

brackets and guard rail complete fixed with 40 mm long screws, rawl

plugs etc., complete.

Providing and fixing trap of self cleansing design with screwed down

or hinged grating with or without vent arm complete, including cost

of cutting and making good the walls and floors : 100 mm inlet and

100 mm outlet Sand Cast Iron S&S as per IS: 1729

Providing and fixing trap of self cleansing design with screwed down

or hinged grating with or without vent arm complete, including cost

of cutting and making good the walls and floors :100 mm inlet and 75

mm outlet Sand Cast Iron S&S as per IS: 1729

Providing and fixing PTMT Waste Coupling for wash basin and sink, of

approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62 mm breadth

weighing not less than 45 gms.

17.7 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm,

effective length of tail pipe 260 mm from the centre of the waste

coupling, 77 mm breadth with 25 mm minimum water seal, weighing

not less than 260 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125

mm high and 112 mm distance from wall of standard shape with

bracket of the same materials with snap fittings of approved quality

and colour, weighing not less than 105 gms.

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,

200 mm wide with minimum distances of 37 mm from wall face with

concealed fittings arrangement of approved quality and colour,

weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to

17.73 wooden cleats with CP brass screws with concealed fittings

arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and

effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete as

per direction of Engineer in Charge.Internal work -

183 18.7.2 Exposed on wall 20 mm nominal outer dia Pipes m 1000.00 325.96 325955.00

184 18.7.3 Exposed on wall 25 mm nominal outer dia Pipes m 1000.00 390.71 390708.15

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

185 18.7.4 clamps at 1.00 m spacing. This includes jointing of pipes & fittings m 800.00 504.74 403795.00

with one step CPVC solvent cement and testing of joints complete as

per direction of Engineer in Charge.Internal work - Exposed on wall

32 mm nominal outer dia Pipes

Providing and fixing CPVC pipes having thermal stability for hot and

cold water supply including all CPVC plain and brass threaded fittings

including fixing the pipe with clamps at 1.00 mt spacing. this includes

jionting of pipes and fittings with one step CPVC solvent cement and

the cost of cutting chases and making good the wall same including

testing of joints complete as per the direction of engineer incharge

concealed work including cutting chases and making good the wall

15 mm nominal outer dia pipes

187 18.8.2 20 mm nominal outer dia pipes rmt 1622.00 523.08 848443.55

188 18.8.3 25 mm nominal outer dia .Pipes. rmt 1622.00 610.31 989929.71

189 18.8.4 32 mm nominal outer dia .Pipes. rmt 1622.00 719.34 1166767.70

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

Providing and fixing uplasticised PVC connection pipe with brass

18.21.1 30 cm length

18.21.2 45 cm length

Providing and placing on terrace (at all floor levels) polyethylene

water storage tank, IS : 12701 marked, with cover and suitable

locking arrangement and making necessary holes for inlet, outlet and

overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931:

18.54 Providing and fixing PTMT bib cock of approved quality and colour.

197 18.54.3 15 mm nominal bore, 165 mm long. Weighing not less than 110 gms. Each 500.00 172.08 86037.53

18.55 Providing and fixing PTMT stop cock of approved quality and colour.

198 18.55.1 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. Each 500.00 115.30 57650.25

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

18.56 Providing and fixing PTMT pillar cock of approved quality and colour .

15mm nominal bore, 125 mm long foam flow. Weighing not less than

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing C.P. brass long body bib cock of approved quality

200 18.51.1 conforming to IS standards and weighing not less than 690 gms. Each 120.00 777.38 93285.40

15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and

201 18.53.1 geyser points of approved quality conforming to IS 8931 a) 15 mm Each 120.00 558.79 67055.27

Providing and fixing CP Brass shower rose with 15 or 20 mm inlet,

150 mm diameter

Dismantling old C.I. pipes including excavation and refilling trenches

after taking out the pipes, breaking lead caulked joints, melting of

203 18.82.2 lead and making into blocks including stacking of pipes at site lead metre 600.00 323.52 194113.50

100 mm diameter C.I. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes

with collars jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement : 2 fine sand) including testing of joints

etc. complete :

Total Sanitary & plumbing works 10551918.45 -

Repairing Steel windows broken handle base / stay handle base / peg

stay base etc. in any floor of the bldg. by supplying and fixing by

welding with new stay handle base / peg stay base / M.S handle base

including cutting the old one and preparation of surface for welding

with new materials including painting with red-oxide primer

complete as per direction of Engineer-in-Charge.

Repairing of broken Steel Window hinges ( in any floor of the

building) by supplying and fixing with necessary hinges, nuts, bolts &

washers etc.as per IS including cutting and removing the old broken

hinges, nuts, bolts and washers etc. including preparation of the

surface for new one. Red-oxide primer should be applied over the

new hinges as per direction of Engineer -in-charge

Supply and installation of VISTA or equivalent Fabric -polyster

209 MR Vertical Blinds of Slat width 100 mm and Slat thickness 0.80 mm per sqm 200.00 0.00 7,64,541.01

drawing and direction of E/I

Removal and cleaning of one or more vegetation/ plants from walls

roofs, chajja etc.up to 4 sqm area, chemically treatment of surface to

210 MR prevent further growth, and making good the surface by plaster , nos 500.00 704.28 3,52,140

grouting ,waterproofing , etc. as the case may be including necessary

scaffolding staging etc.

Clearance and disposal of Jalkumbhi/water Lily from water bodies

including removing and rental cost of boat, labour etc. complete with

211 MR disposal of material to approved municipal dumping ground sqm 12000.00 50.00 6,00,000

including all other charges for materials and machinery with all lead

Cleaning rubbish, sludge, scum, liquid earth, mud etc. from water

bodies by by mechanical/ manual means including all labour, tools &

plants etc. including getting out and disposal of excavated earth, lead

up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge.

Total NS Plumbing 43,62,645

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Non Schedule Items- Plumbing

Replacement of G.I fittings like elbow, short piece T, reducer, bend

and chek nut etc. of any dia. by removing the old one without

213 Old Sor damaging of other fittings and fixtures at any height of the building Each 419.00 39.96 16,743

including returning the removed materials to the Main Post or as per

direction of EIC.

Supply, installation , testing commissioning of PP Mineral filled low

noise Soil & Waste system as per EN 12056, with density 1.9

g/cm3. PP mineral(Astolan) filled Low noise system should has a

fire classification DIN 4102-B2/EN13501 . Product should have a

chemical resistance of pH 2-12 and is a complete sound

protection system according to DIN 4109. including with push fit

rubber ring sockets all necessary fittings and specials such as

Bends, junctions, offsets & vent cowl. Fixing at wall/ceiling level

supported by rubber line bracket & hangers etc. duly epoxy

coated. Cutting, chases/holes in floors / walls / slab.Compliant with

LABC. Weight mass per unit area of DN100MM should not be

less than 110.07kg/m3. sound levels of not more than 15dBA as

per EN 14366 at a flow rate of 4 l/s.including all core cut ,chases

,cutting making holes in all wall and floor as required complete in

Providing Fixing straight /offset type single body push fit type WC pan

connector with factory supplied spring loaded seal guard with

218 NS integral single mould sealing fins made of flexible EVA body, Each 60.00 800.00 48,000

including bush/adaptor as supplied with the pan connector (if

Providing and fixing floor drain (FD) with 50mm/40mm outlet and

219 NS one 40mm inlet for waste, with SS grating (adjustable height), Each 60.00 1655.00 99,300

having 50mm water seal and in-built NRV

Providing and fixing PP/UPVC trap of self cleansing design with screwed

down or hinged grating with or without vent arm complete, including cost

of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet

220 NS Sand cast iron S&S as per IS: 3989 Each 60.00 1655.00 99,300

Providing and fixing PP/ UPVC grating with Cockroach proof

strainer of approved design including setting in floor with cement

motor to match with floor finish as per architect requirement

suitable for waster and FT.

Providing and fixing PP/UPVC brass grating with frame of

approved design including setting in floor with cement motor to

match with floor finish as per architect requirement.

Providing and fixing PP/UPVC extention piece for 100 mm dia floor

trap formed out of main pipe with multiple side inlets, suitable for

various dia pipes including all fixtures as required complete as per

drawing approved sample and direction of engineer in charge.

Providing and fixing Jaguar make ARI-39041 Two way bib cock with

225 NS Providing and fixing Jaguar Make COP-057PM C.P. angular valve Each 20.00 881.08 17,622

Providing and fixing ESSCO make MQT-514 FKN Concealed Stop

227 NS Providing and fixing Jaguar make COP-273PM Short body bib cock Each 20.00 1195.78 23,916

228 NS Providing and fixing Jaguar make OHS-1989 Overhead shower Each 20.00 1407.90 28,158

229 NS Providing and fixing Jaguar make ALD-573 B138Health Faucet Each 30.00 1482.11 44,463

Name of Work- Daily Complaints for Civil and Plumbing works of BSL Township

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY (Rate as per AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing Jaguar make ACN-1111SM Towel rail 600 mm

231 NS Providing and fixing Jaguar make AHS-1551 Toilet paper Holder Each 20.00 1495.43 29,909

232 NS Providing and fixing Jaguar make CAN-1161N Double coat hook Each 30.00 657.99 19,740

Providing and fixing Jaguar make SDR-WHT-DJ0010F Soap

Providing and fixing Jaguar make CNS-WHT-705 Under Counter

235 NS Providing and fixing Jaguar make Pillar cock Each 30.00 1928.56 57,857

236 NS Providing and fixing Jaguar ESSCO Waste coupling Each 30.00 548.57 16,457

Total of the Sub-Head -Plumbing NS

Total NS Plumbing 30,78,856