REPAIR/REPLACEMENT OF FLOOR / WALL TILING, CGI /PGI SHEETS, FALSE CEILING AND OTHER MISC B/R WORKS AT JCOs/ORs MD ACCN IN ZONE III AND IV AREA AT AGE B/R-II UNDER GE DINJAN

Amount

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as directed.

Refixing of shutters in existing location/ opening exceeding 1 sqm but not exceeding 2sqm each including resecuring or easing & adjusting also refixing existing serviceable builders hardware complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing the rubbish off the premises complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed

Taking down cement plaster or cement lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retreived debris as directed including necessary scaffoldings etc complete all as directed.

Hacking out old broken glasses (any thickness/type and in any position) from wooden frames/ metal frames fixed with oil putty or beads etc and removing from site complete all as directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and as directed.

M&L for PCC (1:2:4), type B0 ( using 12.5 mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs,, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C1 (using 20mm graded stone aggregate) as in back filling of pressed steel frame, cills, hold fast, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60cm in height, copings, kneelers, apex stones, bed plates, kerbs including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for precast cement concrete type B0 (1:2:4) (using 12.50 mm graded aggregate) as in louvers and jallies, 25mm thick (measured solid), including all mouldings but excluding frame set in cement mortar (1:6) complete all as specified and directed.

M&L for RCC (nominal mix) Type B0 (1:2:4) (12.5mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, etc complete all as specified and as directed. (Note: Reinforcement shall be measured & paid separately) .

M&L for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Cutting chases, pinning in making good to facings where required and pointing in cement motar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slab, floor slabs, landing covers, and similar works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs exceeding 5cm but not exceeding 10cm wide fir rough finished surfaces of concrete flat complete all as specified and as directed.

S&F 35mm thick second class class hard wood glazed and skelton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, complete all as specified and directed.

S&F factory made 35 mm thick 2nd class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F flush door shutters 35/40mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with partcle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 200mm long mild steel, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S & F 150 mm long, Mild Steel, barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and directed.

S&F for 150 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed.

S&F for mild steel sliding door bolts, 250mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

S&F Mild steel butt hinges, Medium grade, 75 mm size , complete all as specified and directed.

S&F Mild steel butt hinges, Medium grade, 100 mm size , complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F for 150 mm size mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed.

S&F in repairs curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F for mild steel small articles using flat iron such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S&F 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate etc complete all as specified.

S&F for anodised aluminium grill, (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screw @200mm c/c, including cutting the grill to proper opening size for fixing approved anodised aluminium standard section around the opening, complete all as per manufacturer instruction and directed by Engr-in-Charge.

S&F aluminium anodised snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and as directed. Make of E-Board : Eternit Everest / Lafarge/ Armstrong/Visaka Industries Ltd.

S&F Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed.

S&F in repairs 18/19 mm thick pre-laminated particle board exterior grade pre-laminated one side with decorative choice laminated and other side balancing white lamination fixed with screws to timber frame work as in cup board shutters, partitions and shelves complete as specified and directed.

M&L for special treatment for sunken portion of WCs/ Bath & toilet executed in following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris from site of work etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per Manufacture's instructions.Complete. Stage 3:- Apply Dr Fixit Primeseal primer or Equivalent of STP Ltd (and allow to dry for 8 hours) all as per Manufacture's instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP (The surface after painting one coats shall be allowed to dry for 6 hours before next coats) all as per Manufacturer's instructions. Stage 5:- Rendering 10mm thick in CM 1:3 mixed with Integral water proofing chemical Dr Fixit Pidicrete URP or plaster seal of STP Ltd all as per Manufacture's instructions. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP all as per Manufacture's instruction. Stage 7:- Making holes in wall and fixing 600mm long 40mm dia medium grade GI spout for draining the surplus water if any . Stage 8:- Carry out ponding test for 48 hours to ensure water tightness of repaired sunken portion water tightness of repaired sunken portion and filling of sunken portion for cement concrete Type E2 1:5:10 using 40 mm graded aggregate as in lean concrete complete all as specified and directed. Note :- (a) Only plan area shall be measured and accounted for payment under this item. (b) Depth of sunken portion of WC's/Baths shall be upto 35cm, which is to be taken into account while quoting the rate against this item. (c) Rate quoted by Contractor shall be deemed to be included for all the horizontal and verticale treated surfaces of sunken portions of WC & Bath.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a)Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L 25 thick cement concrete type B0 1:2:4 (12.5 mm graded aggregate) finished even and smooth. (c) Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight). (d) M&L for 20 mm thick screed bed in cement mortar 1:4 finished even and smooth. (e) Preparing & cleaning of fully dried cement plastered surface. (f) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384. (g) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (h) One coat of aluminium paint over APP membrane @0.11Kg/Sqm. Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

M&L for 75 mm thick PCC (1:3:6) type C-2 (using 40mm graded aggregate) thick as in plinth protection/Hard standing , etc finishing cement concrete surface even & fair without using extra cement making joints with bitumastic filling in proportion of bitumen and sand 1:2 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

M&L for coloured 450x350x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting, dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30 cm size, 25 mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry in floor with grey cement mixed with pigments to match with the colour of tiles, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 20mm thick granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite complete all as specified and directed.

M&L for Kota stone slab 18-20mm thick in floor laid over and including 20 mm thick screed bed or bedding layer of cement morter (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as specified and directed.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:4) including rubbing and polishing all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as sub base of flooring complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggt as in floors finished even and smooth with using extra cement, complete all as specified and directed.

M&L for rendering 5mm thick in cement morter (1:3) on ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick wall on other than fair faces of brick work or concrete surfaces in cement mortar in (1:6) and finished even and smooth (without using extra lime or cement) complete all as specified and as directed.

M&L for rendering 20 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10mm thick each layer) in cement mortar in (1:4) using water proofing compound in top layer and finished even and smooth (without using extra lime or cement) complete all as specified and directed. Note: Water Proofing Compound measured and paid separately.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand morrtar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed.

M&L for applying three coats of colour wash on new plastered surfaces of walls, complete all as specified and directed.

M&L for applying three coats of white wash on new ceiling surface including preparation of surface, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over one coat of primer after preparation of surface complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane complete all as specified and directed.

M&L for preparing of new wooden surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F 15 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

S&F 20 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Refixing old steel tubing 15mm bore and connections in new or old position (walls/ceilings/floors etc) complete all as specified and directed.

Refixing old steel tubing 20 mm bore and connections in new or old position (walls/ceilings/floors etc) complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowL size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white with "P" or "S" Trap front or back inlet fixing bolts, PVC seat cover complete and making all necessary connection as specified and directed.

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) incl setting the trap and pan in cement mortar (1:3:6) all round and "P" or "S" Trap, complete all as specified and directed.

S&F in repair 10Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F in repairs Vitreous China wash hand basin, white, flat back, size 550x400mm with coupling , waste, chain and plug and porcelain stopper, brackets, with and incl 32mm dia 90cm long PVC waste down pipe, but excluding taps complete all as specified and directed.

S&F for 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed.

S&F in repairs grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

S&F in repairs, 15mm cromium plated Bib taps, cast copper alloy with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repairs Bip tap standard of PTMT any colour screwed for iron pipe and fixed (Minimum weight 15mm - 90gms) complete all as specified and as directed.

S&F in repairs cromium plated Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F repairs 15mm bore dia Stop cock cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and replacement in repairs of brass spindles, phases of brass of any size required 3/4/5 for bib taps, pillar cocks, stop cocks, angle valves, concealed valves complete all as directed.

S&F in repairs, swival shower of PTMT 15mm bore (minimum weight 40 gms) including shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum wt 40 gms) complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F in repairs 110mm bore, PVC (SWR) pipes type 'B', single socketed in any length with rubber ring joints fixed to walls using MS holder bat, fixed complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed

S&F for 75 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe incl 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minimum weight 20 mm - 210 gms ) complete all as specified and as directed.

S&F in repairs Ball valves high pressure of PTMT 20 mm bore with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms), screwed for iron pipe etc complete all as specified and directed.

M&L for forming 12mm thick expansion joints in 100 mm thick concrete slabs, filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’, complete all as specified and directed.

Cleaning of open shaft of bldg including gully trap, cleaning with wire brush incl of grass, roots, bushes etc and taking out accumulated garbage etc, from shaft and removing the same to a distance not exceeding 50 meter, complete all as specified and as directed.

Checking and attending to complaints of no water supply, water leakage from bib taps, stop cock, pillar taps, flushing cisterns, wash hand basins, urinal, wall mixer/basin mixer, angle valve, concealed valve,shower rose , health faucet & jet, float valve, of any type & size or any other water supply fittings/fixtures incorporated in plumbing works any where in the bldgs which is causing obstruction to water supply in area & requires plumbing including carrying out minor repair such as replacement of washers, brass spindle/phases of brass, check nuts, tightening of fittings of flushing cistern or any other repair not mentioned herein before etc using petty materials like washers, thread (soot), Teflon tape, M-Seal, screws (any size), nails (any size) to make water supply/plumbing lines & fiittings/fixtures functional and leak proof to the satisfaction of the occupants/ users complete all as directed. Note : (i) The rate of above mentioned item incorporates use of any materials & equipment used for completing the complaints on time to the satisfaction users/occupants. (ii) Contractor or his authorised representative shall collect such type of complaints mentioned here in above from complaint cell at 8.30 AM on daily basis except Sunday & Holiday & submit the completion of complaints on the next day duly signed by the users/occupants. No extra payment shall be made on account of collection of complaint and submission of complaints . (iii) Complaints must be completed with in 24 hrs without any fail otherwise recovery shall be made double the market rate to the contractor. (iv) Any items required to be replaced shall be paid under respective items and in that case this items shall not be measured and paid.That complaint should also be completed within 24 Hrs without fail.

Checking and attending to carpenter complaints from all joinery works/cup boards etc including petty repairing wk with materials like nails/screws/beads/oil putty as per site requirement to the satisfaction of the occupants/users complete all as directed. Note : (i) The rate of above mentioned item incorporates use of any materials & equipment used for completing the complaints on time to the satisfaction users/occupants. (ii) Contractor or his authorised representative shall collect such type of complaints mentioned here in above from complaint cell at 8.30 AM on daily basis except Sunday & Holiday & submit the completion of complaints on the next day duly signed by the users/occupants. No extra payment shall be made on account of collection of complaint and submission of complaints . (iii) Complaints must be completed with in 24 hrs without any fail otherwise recovery shall be made double the market rate to the contractor. (iv) Any items required to be replaced shall be paid under respective items and in that case this items shall not be measured and paid.That complaint should also be completed within 24 Hrs without fail.

Shree Trilok Electric Corporation (BID ID -3433239)

M/S HAZARIKA CONSTRUCTION (BID ID -3432126)

M/S CHANDAN ENTERPRISE (BID ID -3433094)

M/S AUTOMOTIVE WORLD (BID ID -3433301)

jitendra narayan goswami (BID ID -3433363)

Bimal Trading Company (BID ID -3431855)