CERTAIN REPAIR TO JOINERIES (WITH PAINTING) INCL ALUMINIUM WORK, FLOOR AND WALL TILING WORK INCL WOODEN FLOORING ,WALL PANELING, ROOFING, CEILING, LUMBING, SANITARY APPLIANCE /FITTINGS, FLOORING, PLASTERING AND HERITAGE FINISHES ETC OF BLDG LOCATED I

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete complete all as specified & directed.

M&L for brick work using fly ash brick conforming to IS-12894 2002, non modular, class designation 7.5, straight or curved on plan, exc. 6.0 m mean radius in CM (1:6) complete all as specified & directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified & directed.

M&L for rendering 15mm thick in cement plaster in CM 1:4 on surfaces fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified & directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in CM 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified & directed.

M&L for rendering 15mm thick in CM 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified & directed.

M&L rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of wall with integral water proofing compound @ 3% by weight of cement surfaces finished even and smooth without using extra cement complete all as specified and directed.

Supply only water proofing compound complete all as specified and as directed.

M&L for preparation of new or previously undecorated surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer by using roller complete all as specified & directed.

M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash complete all as specified & directed.

Demolition of plain cement concrete of any description and in any position not otherwise specifically provided for complete all as specified & directed.

M&L for 40mm thick PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in flooring, finished even and smooth without using extra cement complete all as specified & directed.

Supply only glass dividing strips 38mm wide and 3mm thick and inserted in position to confirm design etc complete all as specified & directed.

M&L for 75mm thick PCC 1:3:6 typeC-2 using 40mm graded stone aggregate as in plinth protection complete all as specified & directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in flooring, finished without using extra cement complete all as specified & directed.

M&L providing 25mm thick precast plaincement concrete jallies PCC 1:2:4 type B-0 (using 12.50mm graded stone aggregate) (measured solid) including all moulding and set in CM (1:6) complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in coping benching finished fair and even including necessary form work complete all as specified & directed.

M&L for precast PCC 1:2:4 type B-0 using 20 mm graded stone aggregate as in lintel up to 1.5 m clear span, cills, steps, bands, including weathering, slightly rounded or chamfered angles, throating set in CM 1:4 and other similar works including necessary form work complete all as specified & directed.

Demolition of stone slabs and tiles of any description or thickness in floors, platform, aprons etc. laid, bedded and pointed in any mortar complete all as specified & directed.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps jambs, pillars, window-cills cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

S&F in repair dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 Sqm area not exceeding 0.5 Sqm fixed with and including on number SS clamps (grade-202) of flat 30mmx2mm , 50 mm long made to shape in each slab making V groove at top and bottom of stone and drilling hole for hold fasterner, polishing, rubbing and including silicon treatment, pointed with an admixture of white cement and dholpur stone dust 1:1 complete all as specified & directed.

M&L for 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified & directed.

S&F for 25 mm thick exterior tiles superior quality of approved size/design/shade set & jointed in neat cement slurry & pointed in white or coloured cement to match as in floor including 20mm thick screed bed in CM 1:4 complete all as specified & directed.

S&F for 60 mm thick M-35 grade ISI Marked, machine pressed, precast concrete rubber moulded interlocking coloured paver block of any shape and size over including 25 mm thick sand cushion complete all as specifed and directed .

M&L for Ist class exterior floor tiles of size 600x300x10 to12 mm thick of approved colour and shade laid over 20mm thick screed bed in C:M 1:6 complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified & directed.

M&L for non skid finish ceramic coloured tiles 7 to 8 mm thick joint free (area of each tile exc. 0.06 but not exc 0.11 Sqm) set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 15mm thick screed bed in CM 1:4 complete all as specified & directed.

M&L for non skid finish ceramic coloured tiles 7 to 8 mm thick joint free (area of each tile exc. 0.18 but not exc 0.38 Sqm) set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 15mm thick screed bed in CM 1:4 complete all as specified & directed.

M&L for glazed coloured ceramic tiles 300x450x7 to 8mm/ 450X350x7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 as in vertical surfaces complete all as specified & directed.

M&L glazed coloured ceramic tiles 300x600x7 to 8mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 as in vertical surfaces complete all as specified & directed.

M&L for 10mm thick vitrified ceramic tiles light/dark shade (square/rectangular) polished ,area of each tiles not exc 0.36 sqm in floor etc. , set and jointed in neat cement slurry and pointed in white/coloured cement to match 15 mm thick in net cement screed bed in CM (1:4) complete all as specified & directed.

M&L for 10mm thick vitrified ceramic tiles dark shade (square /rectangular), polished, area of each tile exc 0.42 sqm but not exc 1.00 sqm in floor etc. , laid over 20 mm thick screed bed in CM 1:4 ,set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified & directed.

All as per item No 35 above but in verticle surfaces over 10mm thick rendering in CM 1:3 complete all as specified & directed.

S&F solid PVC wall linning consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified & directed.

S&F 5 mm thick PVC sheet fillet of width 35 mm thick for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified & directed.

Refixing of aluminium frame fixed with glazed/ particle board in panels including wooden wall panelling and all necessary repair and replacing the aluminium snap beading, rubber packing, glazing clip etc upto maximum height 2.5mtr complete all as specified & directed.

S&F in repair 1.5mm thick powder coated anodized aluminum partition wall partly paneled and partly glazed size of aluminum section 44X44x 1.5 to 1.8mm thickness divided into square or rectangular (not exc. 1.20Sqm each panel ) in shape top panel shall be glazed with 5.50mm thick sheet glass any shade& design & bottom panel shall be of 12mm thick prelaminated particle board exterior grade with both side choice lamination including necessary joining cleats glazing clips, rubber packing, anodized aluminum snap beading screws complete all as specified & directed.

Taking down shutter of any description not exc 1 sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws complete all as specified & directed.

Taking down shutter of any description exc 1 sqm and not exc 2 sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws complete all as specified & directed.

Taking down chowkat or frame with shutters area not exc 1.5 sqm each (without taking off the shutters from the frame) including irom mongrey and cutting holes for hold fasts & making good complete all as specified & directed.

Taking down chowkat or frame with shutters area exc 1.5 sqm but not exc 4 sqm each (without taking off the shutters from the frame) including iron mongery and cutting holes for hold fasts & making good complete all as specified & directed.

Taking down shutter of any description not exc 1 sqm including irom mongrey and removing from side complete all as specified & directed.

Taking down shutter of any description exc 1 sqm but not exc 2 sqm including irom mongrey and removing from side complete all as specified & directed.

S&F powder coated alumium glazed window shutter sliding type using 1.60 to1.80 mm thick aluminium open three track section having size of style & top rails 83x44mm, bottom rils 100x44mm including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading screws, anodised aluminium fittings complete and including glazing by using 5mm thick plain sheet glass and stainless steel wire mesh of dia 0.36mm and apertue 1.4mm complete all as specified and directed. (Note:- Glazed shutters glass thickness not less than 5.00 mm and wiremesh shutter with SS wiremesh as approved by GE is also included. No payment will be made separately)

S&F anodised aluminium grill (opening of gril not more than 100x100mm) fixed to windows or ventilators with anodised aluminium U channel 25x12mm size complete all as specified and directed.

S&F aluminium powder coated frame/chowkat of aluminium door section of 80x44x1.60 to1.8 mm thick fixed with rawal plug and screw or wire expansion hold fasteners complete all as specified & directed.

Providing and fixing powder coated aluminium partly glazed and partly paneled door shutter side hung type using 1.50mm thick standard door section having size of styles, top rails 83x44mm x 1.6 to 1.8mm thick where as bottom rails will be made up of 100x44mm including necessary joining cleats glazing clips, rubber packing, anodized aluminium snap beading screws, powder coated aluminium fittings such as 100 mm long 3 No. aluminium hinges B-21 ,type 01 No. aluminium tower bolt 200mm long and one no mortise lock 100mm size 4 levers (vertical type) and 01 No 300mm size long aluminium sliding bolt and 02 No fancy type fiber glass 150mm dia circular handle shall be provided to each door and glazing of top panel shall be made of 5.50 thick sheet glass and pannelling shall be provided with 12mm thick exterior grade prelaiminated partical board with both side choice laminations, complete all as specified & directed.

S&F aluminium powder coated frame/chowkat of aluminium door section of 100x44x1.60 to1.8 mm thick fixed with rawal plug and screw or wire expansion hold fasteners complete all as specified & directed.

S&F 90x45mm single rebated factory made 100% solid WPC (wood polymer composit) panels door frame made from 100% lead free (singal & extruded process) material with density not less than 780 Kg/cum complete all as specified & directed.

S&F solid PVC flush door shutter 28mm thick, made from Co-extruded three layer rigid PVC foam sheet (Single Extruded) with density not less than 600 Kg/cum outer layer (0.8-1mm) thick should be of rigid PVC with density of not less than 1400 Kg/cum manufactured by an ISO 9001-2015 certified company, Both of surface to be laminated with 0.12mm thick PVC film with suitable adhesive. Door should be water proof, Termite proof, Fire retradant & having good screw holding capacity complete all as specified & directed.

S&F plain, solid, straight chowkats and frames of second class hardwood, wrought, framed rebated on the solid rounded or chamfered, put together with glue, pinned at joints complete all as specified & directed.

S&F for 30mm thick factory made flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified & directed.

S&F for 35mm thick factory made glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed

S&F for 30 mm thick factory made glazed and skeleton shutters for windows and ventilators made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (b) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified & directed.

S&F butt hinges 100mm size extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed, type B-21 complete all as specified & directed.

S&F butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified & directed.

S&F butt hinges of size 75mm medium weight, cold rolled mild steel ISI marked complete all as specified & directed.

S&F small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, articles of 2nd class hardwood, articles not exc 200 cucm each complete all as specified & directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & directed.

S&F in repair brass sliding door bolt 300mm long with sand or die-cast brass hasp & staple(bolt type) and fixing bolts and sliding bolt with rolled or drawn brass bolt complete all as specified & directed.

S&F 125 mm size aluminium alloy handles, fabricated type, extruded section complete all as specified & directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & directed.

Dismantling boarding any description, fixed in any position with nails complete all as specified & directed.

M&L for second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, fixed with screws, sectional area exc 13 sqcm and not exc 25 sqcm complete all as specified & directed.

M&L for 12 mm thick plywood grade BWR type BB, fixed with screw to timber frame work block board ,grade 2 quality , interior grade having both sides commercial faces fixed with screws to timber frame work, complete all as specified & directed.

M&L for 6 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screws to timber frame work, complete all as specified & directed.

M&L in repair 19/20 mm thick prelaminated particle board, interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work fixed etc complete all as specified & directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified & directed.

S&F stainless steel dull finish handles extrude type 100mm size complete all as specified & directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position, unframed work complete all as specified & directed.

M&L for second class hard wood (wrought) as in timber scantling fixed in framed work complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified & directed.

S&F GI frame for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having knurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long complete all as specified including 12mm seamless calcium silicate ceiling made out of 1800 x 1200mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seamless finish complete all as specified & directed.

S&F 12mm thick plain Gypsum board false ceiling 600mmx600mm with GI frame work including all necessary drilling , cutting to fix electrical items as under:- (a) GI sheet channel 30x25x20mm of 24 Gauge fixed with rawl plug and screws 450mm centre to center alongwith perimeter of walls. (b) GI sheet channel made to shape 50x40x40mm of 24 gauge placed @ 600mm centre to centre from perimeter of wall except long wall (in one span) (c) GI sheet intermediate runners of size 45x10x10mm of 24 gauge fixed @ 1200mm centre to centre leaving frame of one side wall (in other span) (d) GI sheet 25mm wide & 20mm gauge suspenders fixed with steel fasteners to roof, ceiling @ 1200mm centre to centre incl plugging in RCC slab. (e) Fixing of 12mm thick gypsum boards, filling joints with P.O.P and finishing complete with two coats of oil of plastic emulsion paint over one coat of primer on ceiling.

S&F false ceiling with 4mm thick E-board white prelaminated set embosed reinforced designer ceiling board of approved texture fixed with GI imposed grid frame work of size not more than 600x600mm having 24mm wide T-section runner made of 0.33mm GI sheet and angle made of 0.45mm, GI sheet suspected with 4mm dia GI wire including two coats of plastic emulsion paint over one coat primer complete all as specified & directed. (Note. All exposed surface of grid work shall be powder coated white.)

Excavation in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S&F mild steel framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & directed.

S&F for framed work as in doors or gates of angles or other section with gusset plates, rails, braces etc. complete drilled for fixing of steel sheeting or other coverings, doors etc should be prepared for hanging or sliding with and including either hooks or hinges or steel hanging door fitting (exclusive of steel hanging door fittings and other coverings, running rails and guides and hanging also fastening and fixing complete quality conforming to FE-410W(gde E-250) quality B complete all as specified & directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) , corrugated translucent sheeting sheets in roof covering complete all as specified & directed.

S&F 5mm thick Polycarbonate corrugated sheeting with two corrugation side lap fixed with 'L' type or 'J' type or cranked hook bolts, complete all as specified & directed.

M&L for anodised aluminium snap grid frame work for roofing, complete all as specified and directed.

S&F 6 mm thick asbestos cement, corrugated or semi corrugated sheets in roofs, walls etc and fixed with ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc. complete all as specified & directed.

S&F coloured pre-painted GALVALUME aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws including necessary washers etc, all as per manufacturer's instruction complete all as specified & directed.

All as per item No 92 but plain roofing sheet as in ridge all as manufacturer's instruction complete all as specified & directed.

Disconnected PVC water tanks of capacity exc 500 & not exc 1000 ltr and refixing the same after necessary cleaning and reapir complete all as specified and directed.

S&F for 500 Ltr capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc including dismantling of existing one complete all as specified & directed.

S&F for 1000 Ltr capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc including dismantling of existing one complete all as specified & directed.

M&L in repair wooden boarding first class hard wood 40mm thick as in floors plained one side with butt joints and fixed with secret nails for repair to existing floors in patches, including cutting out, piecing , heading joints etc complete all as specified and directed.

S&F in repair wooden floor tiles of fixed with approved adhesive incl making good the surfaces and matching the edges and matcing the surfaces with adjacent floor including grinding and polishing, complete all as specified & directed.

M&L for antitermite treatment at contact of wood work along internal by chemical emulsion @ 2.25 litre/sqm including drilling & plugging hole etc complete all as specified & directed.

M&L for applying two coats of melamine wood polish on new wooden wall surfaces including preparation and applying sealer/filler etc to have smooth and glossy finish surface to the entire satisfaction complete all as specified & directed.

S&F in repair brass mortice lock, vertical type, size 100mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified & directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150 mm complete all as specified & directed.

S&F for 40mm dia cupboard knobs fixed with nut, screw and washer of mild steel, bright finished. complete all as specified & directed.

S&F in repair aluminium body door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg. and fixed. complete all as specified & directed.

S&F in repair mild steel stove enameled black handles 100mm long for steel windows, left or right, fixed to steel windows with nut, bolt and washer complete all as specified & directed.

S&F in repair mild steel stove enameled black casement stay 300mm long for steel windows, with hinged joint & two plates, with studs complete all as specified & directed.

S&F in repair 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & directed.

M&L double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified & directed.

S&F in repair soap dish CP fixed with and including chromium plated brass screws complete all as specified & directed.

S&F in repair PVC connection 15mm bore, 450mm long with brass coupling fixed in position complete all as specified & directed.

S&F in repair bib tap 15mm dia PTMT any colour screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F in repair CP Bib tap fancy type 15mm dia long body complete all as specified & directed.

S&F in repair CP pillar tap fancy type 15mm dia long body complete all as specified & directed.

S&F in repair CP stop Valve fancy type 15mm bore screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified & directed.

S&F in repair tubular towel rail, brass chromium plated 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete as as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or in floor/wall complete all as specified & directed.

S&F 110mm bore PVC (SWR) bends, any radius complete all as specified & directed.

S&F for 20mm bore ball brass valve high pressure with polythelene float and fly nut complete screwed for iron pipe or brass ferrule and fixed of complete all as specified & directed.

S&F in repair 32mm bore brass chromium plated PTMT bottle trap for wash basin with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified & directed.

S&F for galvanized steel water tubing medium grade of 15 mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down of existing one complete all as specified & directed.

S&F for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down of existing one complete all as specified & directed.

S&F in repair ball brass valve high pressure with polythene float valve and fly nut complete screwed for iron pipe or brass ferrule 15mm bore, complete all as specified & directed.

S&F in repair of 25mm bore gun metal , globe or gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified & directed.

S&F in repair vitreous china bowl type urinal flat back, size of 465 x 355 x 265mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified & directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 600x480mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & directed.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete all as specified & directed.

Taking down old unserviceable sink and S&F stainless steel sink made of 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 495mm x 420mm and bowl size 410mm x 330mm x 160mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0 , complete all as specified & directed.

S&F in repair stainless steel sink with drainage board made of 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink complete all as specified & directed.

S&F in repair plastic water closet seat cover coloured, closed pattern with flat bottom & cover and aluminium anodised hinging device complete all as specified & directed.

S&F in repair PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified & directed.

M&L complete removal of existing treatment from wall and applying 3mm thick wall care putty with primer to make surface proper even and smooth of wall and applying two coats of OBD on surfaces of wall complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) slabs supported on walls, beams, and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length to shape required including hooking ends and binding with mild steel wire (anuelled) wire not less than 0.9 mm dia complete all as specified and directed.

S&F in repair vitreous china squatting pan (Orissa pattern) water closet (white) of size 630x450mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E-2 in filling, making good to floor, complete all as specified & directed.

S&F vitreous china wash down water closet pan (Pedestal pattern EWC), coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid and necessary fittings complete all as specified & directed.

S&F vitreous china wash down water closet pan (Pedestal pattern EWC), coloured, wall mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified & directed.

S&F in repair symphonic action type single/twin type flushing cistern kit any size and any type complete all as specified and directed.

S&F in repair PVC cabinet with mirror and door of size 560X410mm complete all as specified & directed.

S&F in repair CP chain 15 mm dia 1.5 m long for telephonic shower as per sample complete all as specified & directed.

S&F in repair flush pipe of polyethylene of lower high density PVC 32 mm dia for WHB, complete all as specified & directed.

S&F in repair brass chromium plated wall mixer with hot and cold arrangement, long shank suitable 15 mm bore of pipe of approved quality without telephonic shower complete all as specified & directed.

S&F in repair brass chromium plated wall mixer for mixing hot & cold water in 3-in-1 with telephonic hand shower and 1.50m long flexible lead & screwed down for iron pipe of 15mm bore complete all as specified & directed.

S&F in repair chromium plated single hole basin mixer with hot and cold arrangement, long shank suitable 15 mm bore of pipe of approved quality complete all as specified & directed.

S&F in repair chromium plated brass angle valve 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup complete all as specified & directed.

S&F in repair CP brass toilet paper holder fixed to wall with chromium plated brass screw of approved quality complete all as specified & directed.

S&F in repair stainless steel pegs 6 legs fancy type, complete all as specified & directed.

S&F in repair health faucet for EWC CP hand hold with flexible pipe complete set complete all as specified & directed.

S&F in repair 15 mm dia CP two way tap consisting angle valve to control water suitable for jet cleaner complete all as specified & directed.

S&F in repair glass corner shelf assembly consisting of 5.5mm thick sheet glass 250X250mm size fixed with chromium plated brackets complete all as specified & directed.

S&F 12 mm thick toughened glass door shutter of opening size 0.90x2.0 metre in single leaf with necessary matching including all fittings and pivot at top fancy type glass handle of size not less than 300 mm on both sides of shutter to match with colour of glass shutter top and bottom aluminium rail with suitable locking arrangement and all necessary fitting complete all as specified & directed.

S&F in repair CP brass towel ring 150mm dia fancy type of approved shade complete all as specified & directed .

S&F in repair for shower in stall made of acrylic plastic of white colour complete 0.335 x 1.380 m size with 100 mm bore 2 shower ,50 mm bore six shower (body jet), built in shleves for toiletries including single leaver diverter/mixture devices complete all as specified & directed.

M&L for severcing of vertical type shower panel for smooth fuctioning including all necessary fittings such as PVC connector,clamps as well as on/off knob of panel and cleaned all tubes, complete all as specified & directed.

S&F in repair vitreous china coloured half stall type urinal with sensor assembly including CP brass urinal spreader, CP brass waste coupling, CP brass bottle trap, 40 mm dia waste pipe, grating & brackets, complete all as specified and directed.

S&F in repair vitreous china coloured WHB 600 x 480 counter top oval shape cascade pattern ) with pillar taps ,cast copper alloy capstan heads CP PVC connection, CP bottle trap and CP waste coupling 32mm dia in lead to waste pipe complete all as specified and directed.

S&F in repair CP shower rose with arms 15 mm dia complete all as specified & directed.

S&F in repair factory made 18mm thick solid PVC board one side prelaminated decorative teak face & other side white as balancing as in kitchen shelf and shutters including chowkats and all accessories fittings etc complete all as specified and directed.

M&L for heritage natural stone grit/granules finishing shade No. G-1987-9 pure white/coloured , consisting of a two component dry granules (25 Kg per pack made of 92% silica/natural stone particles coated with fade resistant pigments of coating 0.8mm to 1.2mm to be applied in single coat, on a cured smooth levelled plaster without keying , over a coat of primer complete all as specified & directed.

M&L ACP Cladding including alm beedings over the wall/ceiling. complete all as specified & directed.

S&F bricks tiles for wall and facias complete all as specified and directed.

S&F in repair CP towel rack fancy type with brass screws, complete all as specified & directed.

S&F in repair stainless steel/CP Brass tube (50mm dia, height maximum 900mm) with two Nos chain (6mm dia & distance between two tube pole 1.5 mtr) complete all as specified and directed.

S&F in repair curtain rods, coloured, standrad quality, PVC coated not less than 25mm dia with heads at both ends and middle support, rings etc. complete all as specified & directed.

S&F in repair curtain rods, standrad quality,bore not less than 25mm dia and thickness with 1.8 mm with head/ bulbs at both ends and middle support if necessary, rings etc. complete all as specified & directed.

M&L for applying one or more coat of melamine wood polish on old wooden floor surfaces including cutting , grinding with mechanical cutting/grinder cleaning the entire surfaces, applying sealer/filler etc to have smooth and glossy finish floor surface complete all as specified and directed.

M&L for applying two coats of melamine wood polish on new wooden wall surfaces including prepration and applying sealer/filler etc to have smooth and glossy finish surface all as specified and as directed.

M&L for two coats of component acrylic polymer modified cementitious high performance coating( two Componenet) minimum two coats with coverage 6-7 Sqm /kg/ 2 coats, for positive & negative side wateroroofing, product should have excellent bonding, good waterproofing and unmatched resistance to hydrostatic pressure and form highly elastic film with which provides elongation up to 100 as per manufacturer instruction complete all as specified and directed.

M&L for two coats of component acrylic polymer modified cementitious high performance coating( two Componenet) minimum two coats with coverage 6-7 Sqm /kg/ 2 coats, for positive & negative side waterproofing, product should have excellent bonding, good waterproofing and unmatched resistance to hydrostatic pressure and form highly elastic film with which provides elongation up to 100 as per manufacturer instruction complete all as specified and directed.

Cleaning of PVC water tank storage of capacity exceeding 500 ltr and not exceeding 1000 ltr, including necessary cleaning and sanitizing material, complete all as specified and directed.

M/S KAUSHIK CONSTRUCTION