Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹44.4 LAccepted-AOC VILL SANDIPUR PO DWARNARY DISTT PURBA MEDINIPUR KOLKATA 7134403 WB | KOLKATA | PURBA MEDINIPUR | WB | 7134403 | L1 | Accepted-AOC BEING L1 BID | |
| 2 | L2₹46.1 L+₹88,984 (1.97%)Rejected-Finance 1ST FLOOR SIDHARTH TOWER BALTI KHARKHANA BYELNE S J ROAD ATHGAON GUWAHATI KAMRUP ASSAM 781001 | KAMRUP METRO | ASSAM | 781001 | L2 | Rejected-Finance OTHER THAN L1 BID | |
| 3 | L3₹71.5 L+₹26.3 L (58.3%)Rejected-Finance VILL PO KOTA VIA PANAGARH BAZAR DIST BURDWAN WB PIN 713148 | BURDWAN | BURDWAN | WEST BENGAL | 713148 | L3 | Rejected-Finance OTHER THAN L1 BID |
Tender Value
₹47 L
EMD Value
₹94,000
Closing Date
19 Jun 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (I) (CGN) KOLKATA
GE (I) (Coast Guard Navy) Military Engineer Services Damodar Complex Naval Transit Accommodation Hastings, Kolkata700 023
ADDITION/ ALTERATION OF PROTECTION WORK TO TARRACE CLADDING INCLUDING RCC PORCH AND STAIRCASE AT BLDG NO P-76 AND SPECIAL REPAIR TO GANGWAY BRIDGE (P-38) OF PANTOON JETTY AREA AT CGDHQ-8 AT HALDIA UNDER GE (I) (CGN) KOLKATA
2023_MES_597325_1
NIT No 8701/07/2023-2024/05/E8
Open Tender
Civil Works
Item Rate
180 days
HALDIA
AS PER TENDER DOCUMENT
8 documents required · 8 mandatory
₹500
GE (I) (CGN) Kolkata
₹94,000
Yes
12 Jul 2023
22 May 2023
20 Jun 2023
22 May 2023
19 Jun 2023
5 Jun 2023
Amount
Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or water supply pipes lines etc or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.
Removing excavated material (soils) exceeding 250 m but not exceeding 500 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.
Material and labour for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.
Material and labour for hardcore (broken bricks) of gauge not exceeding 63 mm deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.
Material and labour for cement concrete in foundation, filling and mass concrete in 1:4:8 type D2 using 40 mm nominal size graded crushed stone aggregate complete all as specified and as directed.
Material and labour for RCC 1:1.5:3 type B1 using 20 mm nominal size graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. Note:- The structural steel work shall be measured and paid separately.
Material and labour for RCC 1:1.5:3 type B1 using 20 mm nominal size graded crushed stone aggregate as in columns, pillars, piers, posts and struts concrete complete all as specified and as directed. Note:- The structural steel work shall be measured and paid separately.
Material and labour for RCC 1:1.5:3 type B1 using 20 mm nominal size graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note:- The structural steel work shall be measured and paid separately.
Material and labour for RCC 1:1.5:3 type B1 using 20 mm nominal size graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and as directed. Note:- The structural steel work shall be measured and paid separately.
Material and labour for RCC 1:1.5:3 type B1 using 20 mm nominal size graded crushed stone aggregate as in stair case complete all as specified and as directed. Note:- The structural steel work shall be measured and paid separately.
Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed.
Material and labourfor formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified and as directed.
Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and as directed.
Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed.
Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.
Material and labour for mild steel TMT bars 8 mm dia, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.
Material and labour for brick work with fly ash bricks of class designation 7.5 as per IS 12894: 2002, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.
Material and labour for plastering 15 mm thick on fair face of brick work or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed.
Material and labour for plastering 15 mm thick on fair face of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.
Material and labour for plastering 5 mm thick on fair face of brick work or concrete surfaceon ceiling in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed.
Material and labour for preparation of newly plastered surface of wall and applying two coats of anti fungal weather proof paint over and including one coat of alkali resistant primer complete all as specified and as directed
Material and labour for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over one coat of alkali resistant primer complete all as specified and as directed
Material and labour for cement concrete1:2:4 type B1using 20 mm nominal size graded crushed stone aggregate in cills, steps; seismic and other similar bands, plinth courses, parapets, copings, kneelers, bed plates, hold fast including necessary formworks complete all as specified and directed by Engineer-in-charge.
Material and labour for 75 mm thick plain cement concrete 1:3:6 type C1using 20 mm nominal size graded stone aggregates finished surface even and fair as in floor, plinth protection and hard standing all as specified and as directed.
Material and labour for 18 to 20 mm thick granite (ZED BLACK) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like over 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.
Supply and fixed pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.
Supply and fixed pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.
Supply and fixed hot rolled medium and high tensile structural steel of grade E 250 quality A conforming to IS 2062: 2011 as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed.
Supply and fixed hot rolled medium and high tensile structural steel of grade E 250 quality A conforming to IS 2062: 2011 as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.
Material and labour for 60 mm thick factory made colured cement concrete interlocking paver block of M35 grade conforming to IS 15658-2006 made by block making machine with strong vibratory compaction, of approved size, design & shape, cast in rubber mould, glossy finish of approved colour, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water including all necessary scaffolding complete all as specified and as directed.
Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position below or above ground floors, not exceeding 15 cm in depth complete all as specified and as directed.
Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed.
Material and labour for machine-pressed clay interlocking roofing tiles of the Mangalore Pattern, class AA, any size, conforming to IS 654: 1992, laid dry including sreed bed 15 mm thick in cement mortar 1:6 complete all as specified and as directed.
Material and labour for concealed point wiring for one light or one fan or one exhaust fan controlled by one switch complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be included in quoted rate).
Material and labour for concealed point wiring for one 3 pin/ 5 pin 5 Amps socket outlet on the same board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be included in quoted rate).
Material and labour for concealed point wiring for one 3 pin/ 5 pin 5 Amps switch socket combination on independent board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be included in quoted rate).
Material and labour for concealed point wiring for one 3 pin/ 5 pin 15 Amps socket outlet on independent board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 4 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 4.0 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be measured included in quoted rate).
Supply and fixed concealed sub main wiring complete with and including two Nos single core PVC insulated, unsheathed flexible conductor FR-LSH cables 6 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through and including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories and fixed on walls and 6 sqmm one No single core copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable for earthing and connected to common earth dolly complete all as specified and directed by Engineer-in-charge. (Note 1- Two runs of 6 sqmm cable, one run of 4 sqmm cable and one run of conduit shall be measured and paid as one unit length. Note 2- Cost of cutting chase and making good shall be included in the quoted rate).
Supply and fixe metal flush box 3 module complete all as specified and as directed.
Supply and fixe metal flush box 6 module complete all as specified and as directed.
Supply and fixe modular white cover plate with frame, 3 modules complete all as specified and as directed.
Supply and fixe modular white cover plate with frame, 6 modules complete all as specified and as directed.
Supply and fixed white blank plate 1 module complete all as specified and as directed.
Supply and fixe modular switch, 1 way, 6 A, 1 module complete all as specified and as directed.
Supply and fixe modular switch, 1 way, 16 A, 1 module complete all as specified and as directed.
Supply and fixe modular bell push, 1 way, 6 A, 1 module complete all as specified and as directed.
Supply and fixe Modular fan regulator, 120 W, 2 modules complete all as specified and as directed.
Supply and fixe Modular socket outlet modular type 6 A, 2 modules complete all as specified and as directed.
Supply and fixeModular shuttered socket outlet 5 pin 16 A, 2 modules complete all as specified and as directed.
Supply and fixe Modular switch socket combination 6 pin, 16 A, 3 modules complete all as specified and as directed.
Supply and fixe buzzer, din dong, suitable for single phase, AC, 240 volts complete all as specified and as directed.
Supply and fixe ceiling roses, 3 terminal, 6A, 240 V, surface type, intended to support mechanical loads by means of flexible cord, having provision for the connection of switch wiring, screw type terminal, made out of Polyamide or hornbean complete all as specified and as directed.
Supply and fixed flush type AC starter 6M with MCB DP and plug complete all as specified and as directed.
Supply and fixed LED batten light 20 W, made of epoxy powder coated white extruded aluminium channel, operational voltage of 140 volts to 270 volts, frequency of 50 Hz, lumen output of minimum 2100, lumen efficacy of minimum 110 lumens per watt, integral electronic LED driver (SMPS based constant current supply) with output short circuit protection, over voltage protection, surge voltage protection upto 2 KVs, CRI greater than 80%, CW available CCT of 6500K, power factor of minimum 0.95, life span of minimum 50000 working hours complete all as specified and as directed.
Supply and fixe mirror light fitting composite 10 watt LED with Epoxy white powder coated CRCA sheet steel housing with clear/opal acrylic diffuser including connecting flexible wire from ceiling rose to fitting, complete all as specified and as directed.
Supply and fixe LED panel type, surface mounted type, light fitting 12 watts with high power LEDs as light source and electronic driver and Epoxy white powder coated CRCA sheet steel housing complete all as specified and as directed .
Supply and fixed decorative type LED lamp light fittings 9 watts, wall mounted brushed nickel finish with opal glass diffuser suitable for 9 watts LED light B22 suitable base complete all as specified and as directed.
Supply and fixed high energy efficient LED Bulb 9 watts with high power LEDs as light source complete all as specified and as directed.
Supply and fixing BLDC base technology ceiling fan 1200 mm, RPM 370, Air delivery 220 CMM, 35 Watt, with remote control and white colour ceiling fan, BEE rating, five star including connecting with flexible FR-LSH wire complete all as specified and as directed.
Supply and fixed LED 7, watts surface mounted, spot light in matt finish for premium esthetics complete all as specified and as directed.
Supply and fix Heavy duty metal body, Exhaust fans 300 mm sweep, four blade, complete with motor and all required accessories for fixing/hanging complete all as specified and as directed.
Supply and fixed LED building security light nominal power 35 Watt, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumen efficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, protection grade IP 65, CRI greater than 70%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hours complete all as specified and as directed.
Supply and fixe double door MCB Distribution board of sheet metal enclosure, single pole and neutral, 4 way with rated bus bar, 240 volt, IP42 protection grade and fixed with PVC plug and screws and grouted in wall complete all as specified and as directed.
Supply and fixe double door MCB Distribution board of sheet metal enclosure, single pole and neutral, 8 way with rated bus bar, 240 volt, IP42 protection grade and fixed with PVC plug and screws and grouted in wall complete all as specified and as directed.
Supply and fixed MCB, two pole with one protected pole (SPN), unenclosed, panel board type, screw type terminals for external copper conductors, C-type, instantaneous tripping, rated voltage single phase, rated frequency 50 Hz, Rated current 40 A, Rated Short circuit capacity 10 kA, any type of fixation, Protection IP 20 complete all as specified and as directed.
Supply and fixed MCB, SP, unenclosed, panel board type, screw type terminals for external copper conductors, C-type, instantaneous tripping, rated voltage single phase, rated frequency 50 Hz, Rated current 6 to 32 A, Rated Short circuit capacity 10 kA, any type of fixation, Protection IP 20 complete all as specified and as directed.
Material and labour for earthing complete with galvanised steel plate earth electrode 600 mm X 600 mm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to earthing lead of 4.0 mm dia galvanised mild steel wire by means of bolts, nuts, check nuts and washers of galvanised iron from earth plate to test point upto 7.5 metre including all as shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete chamber in cement concrete M15 (Nominal Mix) using 20 mm nominal size coarse aggregate, precast RCC cover slab in cement concrete M15 (Nominal mix) using 20 mm nominal size coarse aggregate of size 40 cm X 40 cm X 5 cm reinforced with 8 mm dia TMT bars @ 150 mm c/c with one handle for lifting made out of 8 mm dia bar, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 20 mm dia GI pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/ strata and testing complete all as specified and as directed by the Engineer-in-charge.
Dismantling of wrought or mild steel work of any description such as in ladder work, bracing/supporting agle iron, roof top MS sheets, railings etc.
Dismantling of plain or corrugated steel sheeting, any gauge, thickness including any pattern roof coverings complete all as specified and as directed.
Dismantling of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed by Engineer in charge.
Dismantling wooden boarding, any description, fixed in any position with nails complete all as specified and as directed.
Taking up or down 25 mm or 32 mm bore of steel tubing and connections, including cleaning for refixing or removal to store or taken on schedule of credit complete all as specified.
S & F hot rolled medium and high tensile structural steel of grade E 250 quality A conforming to IS 2062: 2011 as in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including necessary scaffolding / formwork in foot bridge of gangway in river/ jetty as per site requirement complete all as specified and as directed.
Erection and fixing only hot rolled medium and high tensile structural steel of grade E 250 quality A conforming to IS 2062: 2011 as in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and fixed with angle cleats or other connecting plates including necessary scaffolding / formwork in foot bridge of gangway in river/ jetty as per site requirement complete all as specified and as directed.
Supply and fixed mild steel screw bolts (machine made), diameter of neck 16 to 20 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5 cm but not exceeding 10 cm long complete all as specified and as directed.
Supply and fixed 1st class hard wood as in plain, wooden plank, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed in foot bridge of gangway complete all as specified and as directed.
Refixing of wooden plank of any description, upto 4 sqm to the foot bridge of gangway complete all as specified and as directed.
Supplying & fixing to walls and ceilings or laid in floors 32 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.
Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.
Preparation of old steel surfaces of any description, over 10 cm width or girth by scraping the old paint by wire brush and sand paper and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.
Material and labour for pre-cast cement concrete block masonry with cement concrete 1:2:4, type B1 using 20 mm size crushed stone graded aggregate exceeding 10 cm in width and set in cement mortar (1:4) including necessary formwork complete all as specified and as directed.
Material and labour for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.
Material and labour for preparation of old painted wood or wooden surfaces, of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.
Material and labour for cutting existing steel tubing GI pipe 100 mm pipe and 80 mm and inserting flanged tee with 80 mm pipe and connected to 100 mm dia pipe and fixing resileant valve for inter connection with 80 mm dia for alteration and additions ( Each cut measured) complete and screwing existing steel tubing for alterations or additions ( or lengthening screw op pipe to form connector) complete all as directed.
Supplying & fixing to walls and ceilings or laid in floors 80 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.
Supplying & fixing to walls and ceilings or laid in floors 100 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.
Supply and fixed for 80 mm dia D.I. resilient (soft) seated gate valve with pocket less body, ss stem (AISI 410), EPDM coated di wedge 100% vaccum tight design with toroidal sealing rings & over 250 micron epoxy coating in PN16 designed to BS:5163/IS:14846 non-rising stem type with hand wheel operation complete all as specified and as directed .
Supply and fixed for 100 mm dia D.I. resilient (soft) seated gate valve with pocket less body, ss stem (AISI 410), EPDM coated di wedge 100% vaccum tight design with toroidal sealing rings & over 250 micron epoxy coating in PN16 designed to BS:5163/IS:14846 non-rising stem type with hand wheel operation complete all as specified and as directed .
Supply and Fixed flexible pipe of 100 mm dia and connected with existing GI pipe with all fitting and accessories for connected two gangways complete all as specified and directed.
Material and labour for construction of new valve chamber of size 1000 mm X 1000 mm X 1000 mm including necessary earth work in any type of soil, PCC foundation M10(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate as in base concrete, brick work (one and half brick thick) in CM 1:6 with 20 mm thick cement plaster internally and externally in two coats of (12 mm and 8 mm) in cement mortar 1:4, 100 mm thick RCC cover in M15 (Nominal mix) using 20 mm nominal size graded crushed stone aggregate reinforced with 8 mm dia TMT bars both ways @ 150 mm c/c spacing, handle made with 10 mm dia bar bent in shape of channel with outside projection (100 mm X 200 mm X 200 mm) embedded in RCC, 100 mm thick flooring in PCC M7.5(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate over 75 mm thick hardcore, painting exposed steel surfaces with two coats of bituminous paint and embedded surfaces of steel with two coats of tar, finishing exposed faces of concrete surfaces and plaster surfaces with three coats of white wash complete all as specified and as directed.
Supply & laying unreinforced precast concrete cable cover class LV type 1, flat shape, dimension 250 mm X 150 mm X 40 mm as per IS 5820: 1970 complete all as specified and directed.
Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated cable for working voltages of 1100 V, PVC sheathed, armoured, 3.5 core, nominal cross sectional area of main conductor 240 sqmm, stranded aluminium conductor, ISI marked as per IS 7098(Part-I): 1988 including cable glands, lugs etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc. complete all as specified and as directed.
Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated cable for working voltages of 1100 V, PVC sheathed, armoured, 4 core, nominal cross sectional area of main conductor 10 sqmm, stranded aluminium conductor, ISI marked as per IS 7098(Part-I): 1988 including cable glands, lugs etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc. complete all as specified and as directed.
Supply and fixed cable jointing kit for 1100 V (Earthed) grade cable for straight through heat shrink type joint, indoor/ outdoor type complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 25 sqmm to 95 Sqmm complete all as specified and as directed.
Supplying & laying in trenches 100 mm nominal bore, light grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.
Supplying & laying in trenches 80 mm nominal bore, light grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.
Material and labour for repair and maintenance of existing polycarbonate panel with decarburizing/ cleaning complete LT 415 volts 3 phase panel/ bus bar chamber with electrical connections complete bus bar from the bus bar chamber, cleaning with CTc, connection of all control cables and ensure proper decarburizing, refixing the same after applying Backtol red solution to the bus bar insulator & checking all the connections, tightening the nuts, bolts & thimbles of in-coming/ out-going system complete incl replacement of defective rusted bolts & nuts, below written accessories and Removing existing old paint by scraping from LT Panels supporting MS angles, material labour for two coats of synthetic enamel paint (1st quality) complete all as specified and directed:- (i) Empty Box-Opaque Lid 300X600X170 Mi 0401 Hensel 1 No. (ii) Empty Box-Opaque Lid 300X300X170 Mi 0201 Hensel 1 No. (iii) Opaque Lid MiD 0201 Hensel 1 No. (iv) Hinged Flap Mi KL 6 Hensel 2 No. (v) Wall Gasket Mi WD2 Hensel 6 Nos (vi) Flange Mi FP 20 Hensel 2 No. (vii) Terminal Block (Bolted Type) 50SQ MM DPBB50 ELMEX 4 No. (viii) Barrier Plate BPN70 ELMEX 5 No. (ix) End Clamps SCUSL ELMEX 2 No. (x) Marking Label (1-10) KN 10 ELMEX 1 No. (xi) Terminal Block (Stud Type) 16SQ MM KBT M5-15 ELMEX 4 No. (xii) End Plate KPS4 ELMEX 1 No. (xiii) End Clamps SCUN ELMEX 2 No. (xiv) Marking Label (1-10) KN 6.5 ELMEX 1 No. (xv) Mounting plate(Size 2) Aluzinc/Hylam(AS REQUIRED) REPUTED 1 No. (xvi) Wiring Accessories, Sleeves, End clamp,Acc, Etc. 01 LOT (xvii) Digital Volt meter 0-500 Volts - 01 Nos. (xviii) Digital Ammeter 0-250 amps with suitable CTs -01 No. (xix) R-Y-B LED Indicator Lamps - 01 set
Material and labour for Shifting existing LT Panel from existing location to 200 mtr distance, Making new foundation and base angle and Decarburizing/ cleaning complete LT 415 volts 3 phase panel/ bus bar chamber with electrical connections complete bus bar from the bus bar chamber, cleaning with CTc, connection of all control cables, chnage the defective voltmeter, Ameter and RYB Indication lights, fixing the MCCB at blank space, replace defective base plate, cleaning bus bar or refixing suitable size bar for supply and ensure proper decarburizing, refixing the same after applying Backtol red solution to the bus bar insulator & checking all the connections, tightening the nuts, bolts & thimbles of in-coming/ out-going system complete incl replacement of defective rusted bolts & nuts and Removing existing old paint by scraping from LT Panels, material labour for two coats of synthetic enamel paint (1st quality) by spraying only including writing in/ out going details, capacity in white paint complete all as specified and directed.
Material and labour for repair and maintenance of existing polycarbonate panel with decarburizing/ cleaning complete LT 415 volts 3 phase panel/ bus bar chamber with electrical connections complete bus bar from the bus bar chamber, cleaning with CTc, connection of all control cables and ensure proper decarburizing, refixing the same after applying Backtol red solution to the bus bar insulator & checking all the connections, tightening the nuts, bolts & thimbles of in-coming/ out-going system complete incl replacement of defective rusted bolts & nuts, below written accessories and Removing existing old paint by scraping from LT Panels supporting MS angles, material labour for two coats of synthetic enamel paint (1st quality) complete all as specified and directed. (i) Empty Box-Opaque Lid 300X600X170 Mi 0401 Hensel 1 Nos. (ii) Wall Gasket Mi WD2 Hensel 3 Nos. (iii) Hinged Flap Mi KL 6 Hensel 1 Nos. (iv) Flange Mi FP 20 Hensel 2 Nos. (v) Terminal Block (Bolted Type) 50SQ MM DPBB50 ELMEX 4 Nos (vi) Barrier Plate BPN70 ELMEX 5 Nos. (vii) End Clamps SCUSL ELMEX 2 Nos. (viii) Marking Label (1-10) KN 10 ELMEX 1 Nos. (ix) Terminal Block (Stud Type) 16SQ MM KBT M5-15 ELMEX 4 Nos. (x) End Plate KPS4 ELMEX 1 Nos. (xi) End Clamps SCUN ELMEX 2 Nos. (xii) Marking Label (1-10) KN 6.5 ELMEX 1 Nos. (xiii) Wiring Accessories, Sleeves, End clamp,Acc, Etc. 01 LOT. (xiv) Digital Volt meter 0-500 Volts - 01 Nos. (xv) Digital Ammeter 0-250 amps with suitable CTs -01 No. (xvi) R-Y-B LED Indicator Lamps - 01 set
Supply and fixed MCCB 4 Pole, 415 V, with Microprocessor release 250 Amps with breaking capacity 36 KA complete all as specified and as directed.
Supply and fixed ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 400 Amps complete all as specified and directed.
Material and labour in repair for connection of street Light with two single core PVC insulated unsheathed , 1100 Volts grade, (FR-LSH) copper cable 1.5 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 1.5 sqmm copper conductor and connected to common earth dolly complete as directed Note :-(i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.
Material and labour in repair of PVC cable end terminal boxes outdoor type, and inside (300x200x105 mm), PVC door, fixed on street light poles complete with thermoplastic clamps, GI nuts & bolts with washers suitable for cable incoming and outdoing from bottom with cable glands, comprising of two MCB SP 6-32 Amps, earth termination with nuts & bolts,cable glands and one porcelein connector four way and including 02 sets of 32x6 mm flat iron clamps with nuts, bolts and washers including painting with two coats of synthetic enamel paint over a coat of red oxide primer completed fixed on wall/pole with necessary clamps, screw etc all as specified and directed.
Supply & fixed hot dip galvanized steel perforated cable tray, 300 x 50 mm with minimum thicknes 3 mm, rectanglar type comprising of base plate at bottom, fixed to wall with angle size 40 x 40 x 5 mm at 500mm c/c distance, and outer perforated cover clamped together with GI clamp and GI nut bolts and of suitable width ranging from 4 inch to 8 inch to be fixed on wall with complete all specified and as directed. Note: Disturbed surfaces to be made good, price deemed inclusive of the quoted rate.
Material and labour for repair/maintenance/ servicing of 125 KVA, 3 phase servo voltage stabilizer of Make : Aplab checking all the connections, earthing, coils, level of oils, showing parameters by display, display switch for set all parameters, including replacement of necessary unserviceable parts like LED RYB indicator lamps, 4 way porcelain terminal, gaskets, pre sets, toggle switches, display, PCB controller ckt, meters etc complete all as specified and as directed. Note : (i) Connector, PCB controller ckt, Resistance, lugs etc. measured and paid separately under relevant item of this schedule as supply only. (ii) Labour for taking down, dismantling, connecting back and re-fixing shall be included in the unit rate quoted. (iii) Replacement of other minor parts like LED RYB indicator lamps, 4 way porcelain terminal, gaskets, pre sets, toggle switches, dimmer, meters, transporation charges etc are included in quoted rates of this item. (iv) For maintenance purpose transporation rate deemed to quoted rate.
Material and labour for repair/maintenance/ servicing of 250 KVA, 3 phase servo voltage stabilizer of Make : Aplab checking all the connections, earthing, coils, level of oils, showing parameters by display, display switch for set all parameters, including replacement of necessary unserviceable parts like LED RYB indicator lamps, 4 way porcelain terminal, gaskets, pre sets, toggle switches, display, PCB controller ckt, meters etc complete all as specified and as directed. Note : (i) Connector, PCB controller ckt, Resistance, lugs etc. measured and paid separately under relevant item of this schedule as supply only. (ii) Labour for taking down, dismantling, connecting back and re-fixing shall be included in the unit rate quoted. (iii) Replacement of other minor parts like LED RYB indicator lamps, 4 way porcelain terminal, gaskets, pre sets, toggle switches, dimmer, meters, transporation charges etc are included in quoted rates of this item. (iv) For maintenance purpose transporation rate deemed to quoted rate.
Supply and Fixed accessories porceline/ poly carbonate Connector, Copper lugs, resistance, copper connecting wire etc for 125 KVA Servo Voltage Stabilizer complete all as specified and as directed.
Supply and Fixed accessories porceline/ poly carbonate Connector, Copper lugs, resistance, copper connecting wire etc for 250 KVA Servo Voltage Stabilizer complete all as specified and as directed.
Supply and fixed SVS PCB control card suitable for 125/ 150 KVA servo voltage stabilizer of make Aplab complete all as specified and as directed.
Supply and Fixed in repairs 0.5 HP motor as per existing model and type suitable for SVS of capacity 125 KVA to 250 KVA complete all as specified and as directed.
Supply and Filling 1st hand transformer Oil for Voltage stabilizer as per OEM recommendation complete all as specified and complete.
BHARAT TRADING CORPORATION
NATIONAL CONSTRUCTION CO
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .