GER-71/2022-23 Repair / replacement to tiling, door, walls, windows, roof sheets, plumbing work and connected items under AOR of AGE B/R Dett B under GE 862 EWS

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nanital or similar pattern roof covering, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work, complete all as specified and directed.

M&L for rolled section as in main and cross beam/columns, hip and jack, rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates (Fe-290 Gde E-165 Quality A) complete all as specified and directed. (Note :- All structural steel work shall be painted with one shop coat of zinc chromate red oxide primer including preparation of surfaces before fabrication and rate shall be included in this item).

S&F for steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS - 1161 (1979) grade St-240, complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster of cement mortar 1:3, complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar 1:4, complete all as specified and as directed.

M&L for vitrified tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for 20mm thick black or any other colour granite of any type with table rubbed and polished in steps, jamps, pillars, window, cills, cooking platforms and like, set and pointed in white cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite slab, rounding edges etc, after dismantiling of old unserviceable slab, complete as in repair all as specified and directed.

M&L for Machine cut kota stone slab(mirror polished) flooring 20-25mm thick as in floors and jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including screed bed or bedding layer of 20 mm thick in cement mortar 1:4, after dismantiling of old unserviceable kota stone, complete all as specified and directed.

Description all as per srl item No. 12 above but as in skirting and dado etc

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work using old size bricks sub class 'B', straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4, complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on concrete / brick surface on wall in cement mortar 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on concrete / brick surface on wall in cement mortar 1:4 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on concrete surface in cement mortar 1:3 on soffits of slabs, ceiling, chajja etc finished the surface even and smooth with sagol cement ,complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whitening, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 Sqm and not exceeding 4.0 Sqm each removing form site, complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) n.exc 1.5 Sqm each and removing from site, complete all as specified and directed.

Taking down shutter of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm, complete all as specified and directed.

S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square, complete all as specified and shown on drwaing in SSR Part-II (2020) directed.

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & shown in drawing mentioned in SSR Part-II 2020, complete all as specified and directed.

S&F for box type steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Description all as per srl item No. 28 above but without glazing bar.

S&F for anodised aluminium, power coated (minimum thickness of power coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

S&F for anodised aluminium (minimum thickness of power coating 50 micron) door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, mortice lock, 1 Nos floor door stopper, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F for anodised aluminium window and ventilator shutters, (minimum thickness of power coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 no) suitable handle (1 no) complete all as specified

S&F for sheet glass 5.5 mm thick, ordinary quality and fixed with aluminum & rubber beading in square exc 0.5 sqm in each pane, complete all as specified and directed.

M&L for 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium framework (fittings and fixtures are included in shutter item), complete all as specified and directed.

M&L for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Gde E-165 complete all as specified and directed.

S& F for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks, or galvinsed wire staples, complete all as specified and directed.

S&F for 4 mm thick frosted sheet glass oridinary quality and glazing with oil putty / wooden beads in squares in any size, complete all as specified and directed.

S&F for 100mm long mild steel butt hinges medium weight, fixed to PVC doors, complete all as specified and directed.

M&L for 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked), complete all as specified and directed.

M&L for 125 mm long extruded aluminium alloy handles size fabricated type anodised (ISI marked), complete all as specified and directed.

S&F for sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete as in repair all as specified and directed.

S&F for 1000 ltr capacity three layer (ISI marked) rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball brass valves, high pressure, with polythene float and flynut inlcuding dismantling old tank any capacity complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Taking down old unserviceable GI pipe of 15 /20mm bore with all fittings etc, complete all as specified and directed.

S&F for 15 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc, complete all as specified and directed.

S&F for 20 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc, complete all as specified and directed.

Fixing only 15 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specified and directed.

Fixing only 20 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specified and directed.

S&F for 15mm bore bib tap cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete as in repair all as specified and directed.

S&F for 15mm bore Stop valve (Angle valve), cast copper alloy chromium plated screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed complete as in repair all as specified and directed.

S&F in repair 32mm dia waste coupling of brass chromium plated for glazed ware sinks, basin etc with long screwed shanks and fly nuts, flange and bedded in red lead cement mortar complete all as specified and directed

S&F in repair 32mm dia waste coupling PTMT (half or full threaded), minium weight 60 gms) fixed to stainless steel sinks, complete all as specified and directed.

S&F for brass chromium plated tubular towel rail 20 mm dia "D" type 60 cm long between flange aluminium anodised complete as in repair all as specifed and directed.

S&F in repair 125 mm dia PTMT grating doom stainless steel with waste hole for waste pipe (minium weight 40 grm), complete all as specified and directed.

S&F in repair chromium plate brass connection pipe 15 mm dia with chromium plate brass nuts of length 450mm at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S&F for in reapir for PVC waste pipe 40mm bore fixed to PTMT waste coupling for kitchen sink, complete all as specified and directed.

S&F in repair 20 mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair vitreous China water closet (squatt pan) Orrisa pattern 680x470 mm size pan, white, with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to flushing cistern with flush pipe, complete all as specified and directed.

S&F in repair viterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern) and inlcuding flush pipe set of CP jet with PVC pipe of superior quality complete all as specified and directed.

S&F in repair viterous China water closet pedestal pattern in one piece type of dimention 73cmX36cm74cm including seat cover, floor mounted, 'P' or 'S' trap, flushing kit, CP jet with PVC pipe of superior quality and all necessary fixing arrangements, complete all as specified and as directed.

S&F in repair 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F in repair vitreous China wash basin, white, flat back, size 550x 400mm including waste coupling waste pipe and brackests, complete all as specified and directed.

S&F for in repair sinks with draining board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in repair brass cromium plated mixer for mixing hot and cold water for wash hand basin of 15mm dia screwed down for iron pipe, complete all as specified and directed.

S&F in repair brass cromium plated sink mixer for mixing hot and cold water of 15mm dia screwed down for iron pipe, complete all as specified and directed.

S&F in repair brass cromium plated wall mixer with connection to the over head shower arrangement of 15mm dia screwed down for iron pipe, complete all as specified and directed.

S&F in reapir glass shelf 600mm long including all accessories, complete as specified and directed by the Engr-in-Charge.

S&F in reapir towel ring including all accessories, complete as specified and directed by the Engr-in-Charge.

S&F in repair chromium plate hand shower (Health Faucet) with 1.2 meter long PVC tube & wall hock complete all as specified and directed by Engr-in-Charge.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor, or as in weep hole complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bend any radius, complete all as specifed and directed by Engr-in-Charge.

S&F in repair 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement and connecting to waste pipe, complete all as specifed and directed.

M&L for preparation of new wooden surfaces of any description exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparation of new steel surfaces of any description exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

S&F for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions including dismantling of existing board etc, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level complete all as specified and directed.

M&L for 75mm thick PCC type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand( all by weight) complete after demolation of old cement concrete all as specified and directed.

M&L for 75mm thick PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) as in sub base for tiling, complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description exc 10 cm in width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old steel surfaces of any description exc 10 cm in width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of oil emulsion distemper, complete all as specified and directed.

M&L for complete removal of existing treatment surface of wall and applying one coat of distumper oil emulsion, complete all as speicied and directed.

M&L for preparation of old plastered or unplastered wall surface and applying one coat of cement base paint, completed all as specified and directed.

KANWAL KUMAR GUPTA

MEHTA OM PARKASH

VIJAY KUMAR SURI AND SONS

NATIONAL TRADING COMPANY