ProvidingWellPump RoomAndPipe line NelliyalamScColonyin NelliyalamMunicipality

Amount

Earth work excavation for foundation in all kinds of soils and sub soils to full depth as directed by the departmental officers except hard rock inclusive of shoring strutting and balling out water wherever necessary and refilling the sides of foundation with excavated earth in layers of 15cm thick well rammed and consolidated and depositing the surplus earth with in the compound in places shown by the departmental officers with initial lead of 10 meters and initial lift of 2 meters including cost of all labour charges etc., complete as per standard specification 23 & 24 VI (S2) VII.9,10

Open well excavation complying with relevant clauses of T.N.D.S.S. Well sinking and with lead upto 10 metre in Medium rock and dense medium rock not requring blasting - First depth of 2 metre complete complying with standard specifications. (PWD SOR 2021-2022

First depth

Second depth

Third depth

Fourth depth

Supplying and filling with fine M sand including cost and conveyance of all materials etc., complete complying with standard specifications and as per standard specifications and as directed by the departmental officers

Supply and erecting centering to sides and soffits including supports and strutting up to 5.29m height for plane surface such as R.C.C. slabs Rectangular beams, Tee or Ell beams lintels bed blocks stair case waist slab and landing beams, canopy slabs with all cross bracings using 90cm x 60 cm x 3 mm B.G. 10 stiffened with welded mild steel angles of size 25 mm x 25 mm x 3 mm for boarding laid over (Silver oak joists) of size 10 cm x 6.50 spread at about 90 cm center to center and supported by the casurina props of 10 cm to 13 cm diameter at 75 cm center to center etc., complete complying with standard specifications and as directed by the departmental Engineers.

For pumb room

For well

Reinforced cement concrete in 1:11/2:3[one cement and one and half M-Sand and four the aggregate ] using 20 mm size IRC grade machine crushed chips and excludingcost of reinforcement and centering works and including the cost of mixing,laying , curing ,and etc.,complete complying with standard specification .

Supply and fabricating and placing in position of R.T.S. rods of reinforcement and including the cost of binding wire and bar bending and including the cost of fabrication and using the binding wire at 1 Kg per quintal etc., complete complying with standard specifications.

Plain Cement concrete 1:4:8 mix (one cement and four sand and eight aggregate mix using 40mm size is hard blue granite metal laying in layers of not more than 15 cm thick etc., and including cost of mixing laying, curing etc., complete complying with standard specifications and as directed by the departmental engineers.

Brick work in Cement mortar 1:5 (One cement and six sand) using best quality of second class bricks of size 23 x 11 x 7cm for the following including curing et., complete complying with standard specification and as directed by the departmental officers.

Plastering with cement mortar 1:3 (One cement and Three sand) 10mm thick with well fine screened sand etc., complete including finishing the surface and curing charges etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with cement mortar 1:5 (One cement and five sand) 12mm thick with well fine screened sand etc., complete including finishing the surface and curing charges etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with cement mortar 1:4 (One cement and five sand) 20mm thick with well fine screened sand etc., complete including finishing the surface and curing charges etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of MS Sheet door using 18 guage MS sheet with MS "L" angle 40 mm x 40mm x 6mm including necessary fittings locking arrangements cutting welding revelting cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Painting two coats with approved iron paint over one priming coat of cement paint over cement plastered wall surface and ceiling including cost of one priming coat, Cost of all materials, all labour charges, brushes, cleaning preparing the surface,scaffolding charges and curing charges etc, complete as per SS.

OPENWELL SUBMERSIBLE PUMPSET AS PER IS 14220 / 2002 WITHOUT PANEL BOARD Supply and delivery of Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation. ( 125x125 lpm x m TWAD SOR 2024-2025 )

Supplying and laying of following dia G.I Pipes as per ISI Specifications etc., Complete complying with standard specifications.

50mm G.I Pipe

40mm G.I Pipe

32mm G.I Pipe

25mm G.I Pipe

20mm G.I Pipe

Laying of G.I. Pipes and specials to proper line and level including jointing but excluding cost of pipes and jointing materials for plumbing works for providing water supply and sanitary works in the premises of the building as per ISI Specifications etc., Complete complying with standard specifications. (TWAD : 2020-2021 wITH 40 % ext. For Labor)

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour SD. :63

Supply and fixing of TNEB Moter Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units (500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copperwire with earth connection complete SD. :129

(MAIN SWITCH) TRIPLE POLE SWITCHES (SIDE HANDLE) (STANDARD /HPL/HAVELLS/ EQUIVALENT) 63 Amps TPN Metal clad switch with rewirable fuse units

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to and testing the pumpset and trail run for 10 days.earthing as per IE rules etc., complete andlaying and jointing the cables and twin phasing preventor, water level guard and three pilot (indicating) lamps capacitor single TPICN switches starter, Voltmeter, Ammeter, and erection of panel board consisting of gauges upto the exterior wall of pump room depth valves erection clamps, pressure also fixing of riser pipes to the required required depth

Provision of G.I. special and scour pipes and over flows pies etc., complete

50 mm Dia G.I. Coupling

50 mm Dia G.I.Bend

50 mm Dia G.I.Union

Barrel Nipple 50 mm Dia. 30.00 cm length

50 mm Dia G.M. Gate Valves

50 mm Dia G.I. Equal Tee

50 mm Dia G.I. Equal Elbow

40 mm Dia G.I. Coupling

40 mm Dia G.I.Bend

40 mm Dia G.I.Union

Barrel Nipple 40 mm Dia. 30.00 cm length

40 mm Dia G.M. Gate Valves

40 mm Dia G.I. Equal Tee

40 mm Dia G.I. Equal Elbow

32 mm Dia G.I. Coupling

32 mm Dia G.I.Bend

32 mm Dia G.I.Union

Barrel Nipple 32 mm Dia. 30.00 cm length

32 mm Dia G.M. Gate Valves

32 mm Dia G.I. Equal Tee

32 mm Dia G.I. Equal Elbow

25 mm Dia G.I. Coupling

25 mm Dia G.I.Bend

25 mm Dia G.I.Union

Barrel Nipple 25 mm Dia. 30.00 cm length

25 mm Dia G.M. Gate Valves

25 mm Dia G.I. Equal Tee

25 mm Dia G.I. Equal Elbow

20 mm Dia G.I. Coupling

20 mm Dia G.I.Bend

20 mm Dia G.I.Union

Barrel Nipple 20 mm Dia. 30.00 cm length

20 mm Dia G.M. Gate Valves

20 mm Dia G.I. Equal Tee

20 mm Dia G.I. Equal Elbow

Goods & Services Tax (GST) 18%

sivaprakasam (BID ID -1465156)