Providing Internal and External Electrification Lift and Generator set Arrangements to the Construction of Additional Building in Government Hospital at Parangipettai in Cuddalore District. (Second Call)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3x1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylem sheet covered TW switch box and 5A FT switch (two way)with continuous earth wire connection by 1.5sq.mm copper wire and making good of the concealed portion with suitable colour for concealed staircase light point.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

Supply and fixing of fancy glass shade and 7W / 9W LED bulb

Supply and fixing of 4 Feet LED 20W Fitting with LED 20W tube (Higher End) complete with TW round blocks on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 4 Feet LED 20W Fitting with LED 20W tube (Higher End) complete with conduit pipe suspension from the ceiling with PVC unsheathed FRLS copper leads from terminals to the fitting with tube.

Supply and fixing of 1200mm (48") A.C ceiling fan complete with Fan step regulator 10 0w 2 module in suitable 1/2 module metal flush type box covered with 2 module white cover plate (Higher End ) with 300 mm down rod with fan clamp

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm dia GI bend complete on the existing post/ on wall with PVC unsheathed FRLS copper leads with MS clamps and with painting.

Supply and fixing of 1 no.6A two module 3 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and run of 2 of 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire with painting of suitable colour

Supply and fixing of 3nos.6A two module 3 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 4nos.6/16A two module socket , 4 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of vertical type 8 way triple pole neutral MCCB DB in sheet steel enclosure double door metal cover with IP 43 protection with 1No. 125A MCCB as incoming 6Nos. 63A TP MCB Switch and 6Nos 6A to 32A SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCCB DB,MCCB and MCB's should be with the ISI mark

Supply and fixing of vertical type 4 way triple pole neutral MCB DB in sheet steel enclosure double break metal cover with IP 42 protection with 1No. 63A 4 pole MCB isolator as incoming 1No. 32A TP MCB and 9 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark .

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher EnD.

Supply and run of 4 of 6 sqmm (84/0.3) PVC insulated SC unsheathed FRLS Copper wire Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 6 Sq.mm Copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position.

Supply and clarnping of 3 1/2 x 25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and Laying of 3 ½ x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and clamping of 3 ½ x 50 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 ½ x 50 sq.mm PVC armoured LTUG cable, with earth connection.

Supply and providing cable end termination of 3 ½ x 50 sq mm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply and clarnping of 3 1/2 x95 sq.mm. PVC LTUG armoured cable

Supply and fixing of brass cable gland for 3-1/2 x 95 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 95 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and Laying of 3 ½ x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 ½ x 120 sq.mm. PVC armoured LTUG cable in suitable size 65 mm dia G.I pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 ½ x120 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and clamping of 3 ½ x 120 sq. mm PVC LTUG armoured LTUG cable through 65 mm dia G.I pipe on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ x 120 sq.mm PVC armoured LTUG cable, with earth connection.

Supply and providing cable end termination of 3½ x 120 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Design, Engineering, supply, fabrication, erection, testing, commissioning and handing over of 1 No 20 persons capacity Bed cum passenger lift with Machine room ,speed : 1 m/sec with Stainless Steel Panel ,Disable Friendly ,Microprocessor Based Controller ,VVVF Drive , Fire Rated Doors and ARD with the following Technical Specification.

1. Location: Additional Building, GH Parangipettai 2. No of Lift : 1 No 3. Type of lift : passenger cum bed lift.(1360Kgs) 4. Capacity of lift : 20 persons capacity Gearless passenger cum bed lift 5. Speed : 1.0 M / Sec 6. Type of Drive: Specific variable voltage variable frequency V3F drive with enhanced ride comfort and near Zero leveling functions. 7. No. of floors: (ground + 2 floors)( 3 landing ) 8. Total Travel : 9mtrs Travel. 9. Leveling Accuracy: High level accuracy with smooth & jerk free stopping 10. Construction of Car: 18SWG High quality S.S car Neat hairline finish or Hony comb, S.S hand rail, SS floor line finish, Perspex false ceiling, stretcher impact protection. 11. Position of machine: Directly above the lift well 12. No. of landing entrance: one in front 3 Nos 13. No. of car entrance: one in front only 14. Car entrance door: power operated V3F drive side opening sliding 18SWG stainless steel hair line finish.

27. Emergency light: Battery operated light to be provided with Automatic charging device. 28. Fireman’s switch: To be provided at ground floor 29. Minor builders work: to be provided by lift contractor. 30. Scaffolding: to be provided by lift contractor 31. Sill angles and facia plates: to be provided by lift contractor 32. Steel for lift machinery: to be provided by lift contractor 33. Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by the lift contractor during the guarantee period of one year. 34. Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories.

35. Provision of intercom with phone: To be provided by lift contractor 3 points EPABX system at three places vide 1) inside the car 2) Head room 3) at ground floor attender room 36. Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor. 37. Floor announciator with music, included 38. Special features: a. Infra red door sensor with full height screen. b. Tubular S.S hand rail in cars. c. Voltage stabilizer for circuit control. d. Stainless Steel signal fixtures. e. Vendal proof S.S. Button with S.S. cover f. SS hairline finish door frames for landing doors. g. VF door Register signal h. Call Register signal i. Stainless steel facia plate for car operating panel and landing fixtures. j. Steel ladder for machine room and ladder for lift Shaft pit, k. On – Off switch for fan and light l. Over load warning indicator With audio announcement. m. Fall width half height rear panel mirror. 39. Provision of architraves covering all three sides up to a width of 300 decorum sheet of plywood with TW frame with aluminum beading architraves should also cover the thickness of still level door frame at the landing and indicator boxes at all landings.

40. Other standard features: Voltage stabilizer for control units, Over speed governor, phase failure and phase reversal relay alarm bell, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limits switch, main suspension ropes counter weights lifting hoist for mounting the machineries. 41. Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period not less than one year. 42. Site testing in accordance with IS 14665 should be carried out at the time of handing over. Necessary spares and tools required for the maintenance for a period of one year 43. Supply of operation and maintenance manual with Necessary tools for Operation. The list of tools required should be detailed by the contractor in a separate sheet duly signed by contactor. 44. Disable Friendly Features 45. 2 Hours Fire Rated Doors

Supply, Testing, Commissioning and Handing over of 1 No 40KVA Diesel Generator set with AMF panel with Acoustic enclosure Conforming to CPCB IV + Norms and BIS Specifications (A) ENGINE: Water cooled diesel engine suitable for Generator application with a shaft output of Suitable BHP output for 40kVA, 1500 RPM under NTP condition. The Engine shall comprise the following standard fitting flexible coupling, fly wheel, air cleaner, fan blower radiator, water pump, fuel filter and lubricating oil filter etc., (B) 12 Volt DC Electric Starting Equipment: Complete with Starter motor dynamo, 24V charged standard battery with leads, exhaust piping of 50cms Length. (C) Engine AMF Control Panel / Mounted : Micro processor based LCD display the following Monitoring features: a) Phase Voltages, Phase Currents, kVA, kW, kWh, kVAr Power Factor. b) Lube oil pressure, engine temperature, RPM, Run Hours, Number of starts, Fuel Level, Auto / Manual stop.c) Battery charge condition. d) Common Alarm/Hooter output,and with following Diagonistic features: a) Battery charging failure, Over/Under speed, Over Current, Over/Under Voltage, OverkW, Phase Sequencing, Phase missing.

b) Low lube oil Pressure, High Engine Temperature, Low/High battery voltage, Low fuel level, Over Crank protection, Routing Maintenance indicator, Genset Test Facility. The engine should be cabable of providing 10% temporary over loading. Note: 1. The Control panel should be complete with necessary fuses, cables, lables, other accessories with neutral isolation. 2. The engine should trip for the following conditions. a) Low lubricant pressure b) High water temperature. c) Over speed. (D)ALTERNATOR: 40KVA/32 KW AC 3phase 50c/s 415/420V 0.8PF 1500RPM Capacity Brushless Alternator with special windings to reduce Harmonics with Vacuum Pressure Impregnation and epoxy gel coating on the winding under NTP conditions conforming to IS 13364 (part-II) 1992 to be means of coupling. (E) FUEL TANK: Removable Fuel tank with the capacity of 100 Ltrs locks shall be fabricated out of 14SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connections and mechanical fuel gauge. Fuel tank should be easily removed for cleaning or any maintenance. F) AMF Panel: The AMF control panel cubical should be fabricated with vermin proof and duct proof best quality sheet steel and floor mounted with removable rear panels and hinged front door with enamel paint and incorporating the following suitable provisions for connecting incoming and out going leads having been made on the control panel

Erection of Gen set:- Providing suitable concrete foundation with cement concrete 1:2:4 with sand cushion all around the foundation. Erection of 40 KVA Generator set over the existing foundation with proper alignment of Suitable Bed size .

Supply and fixing of 63A FP MCB in Metal box FP enclosure in flush with wall and making good of the concealed portion with earth connection.

Supply and fixing of 32A FP MCB in Metal box FP enclosure in flush with wall and making good of the concealed portion with earth connection.

Supply and fixing of 100A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixingof 63A TPN MC switch with suitable angle iron frame work with MS cable entry boxes with earth connection only

Supply and fixing of 100A 30mA FP RCCB/ELCB Isolator in suitable FP sheet enclosure in flush with wall and making good of the concealed portion with earth connection.

Supply and fixing of 100A TPN sheet double break switch with HRC fuse and neutral on suitable angle iron frame work with earth connection only

Supply and fixng of TNEB meter board suitable for 3phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2"x1-1/2"x1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1-1/2 feet of 12 mm thickness with necessary bolts and nuts supports and supply and fixing of 3Nos.100A fuse units (500V), 1No. neutral link, copper earth flat of size1"x1/4"with inter connection of EB metert of use units by 16 Sq.mm PVC insulated copper wire with earth connection complete

Earthing as per PWD standard with an earth electrode of 2 metre Class'B 'GI pipe of dia not less than 32mm complete with necessary masonry work

Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and run of 25mm x 3mm copper flat with porcelain insulator with screws on wall/floor for earth connection.

ADD GST 18 %

Please Enable Macros to View BoQ information