PROVN OF DEFI TECH ACCN (OTM) AT KLP FOR MDC KIRKEE

Amount

NOTE: Schedule ‘A’ Part I to X are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-13 only.

Total amount of Sch 'A' Part-I (Building Works)

Total amount of Sch 'A' Part-II (Internal water supply)

Total amount of Sch ‘A’ Part III (Internal Electric Supply)

Total amount of Sch ‘A’ Part IV (External Water Supply)

Total amount of Sch ‘A’ Part V (External Electric Supply)

Total amount of Sch 'A' Part-VI (Road, Path & Culvert)

Total amount of Sch 'A' Part-VII (Sewage Disposal)

Total amount of Sch ‘A’ Part VIII (Area drainage)

Total amount of Sch ‘A’ Part IX (Compound wall, Fencing & Steel Gate)

Total amount of Sch ‘A’ Part X (Excavation, Earthwork & Site Clearance)

SCH 'A PART XI (Air Conditioning) Note: This schedule is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only

Supplying, installing, testing and commissioning of Air cooled type packaged air-conditioning units complete with Hermetically sealed MULTI SCROLL compressors fitted inside the indoor unit & first charge of refrigerant & oil, air cooled condenser, fan section with statically/ dynamically balanced centrifugal blower driven by a TEFC squirrel cage three speed motor, Multi rows cooling coil of copper with aluminium fins etc. The enclosures shall be fabricated of MS. The package unit shall be equipped with sythelic fibre filter, insulated drain pan, controls all encased in a unit. The casing shall be factory made powder coated. Electrical panel board for package units shall comprise of SFU's Fuses. Voltage scanner, complete with overload, low voltage, high voltage & phase imballance protection for the following capacity (MAKES:BLUESTAR/CARRIER/ DAIKIN/ VOLTAS) :

(a) 22 TR Air cooled floor mounted package R 407 C based AC with corded remote controller.

(i) The unit shall be operative on 380 V to 420 V AC 3 ph 50 Hz power supply.

(ii) De-Humidifiers with strip heaters shall be measured and paid seperately.

(iii) Civil works such as masonry foundation/plinth for indoor/outdoor units shall be deemed to be included in the unit rate quoted.

(iv) Power cable connection from LT panel to package unit shall be measured and paid seperately.

(v) Anti vibration pads for indoor /outdoor units shall be deemed to be included in the unit rates quoted.

(vi) The package AC plant shall have pure polyster powder coated GI steel housing comprise indoor & outdoor units of under mentioned specifications:-

Indoor Unit

(ai) Type of blower : Centrifugally forward curved double inlet double width.

(aii) Nominal air flow: 14950 CMH/ 8800 CFM.

(aiii) Capacity contrl : 0,50%, 100%.

(aiv) Air filters : Non wooven polyster media 5 microns enclosed by HDPE mesh.

(av) Controller Unit: Microprocessor based with LCD display.

Outdoor unit

(bi) No of ODUs: 2 Nos operative on 230 V AC single phase 50 Hz power supply.

(bii) Condensor type: Air cooled

(biii) Condensor fan type: Propeller

Intelligent Microprocessor Controller

All units are controlled by microprocessor based controllers with the following features:-

(ci) Seven- segment LCD display.

(cii) Auto restart after power failure.

(ciii) Fault display.

(civ) Run- time equalisation.

(cv) Touch- key on/off switch

(cvi) Single phasing and phase reversal protection.

(cvii) Time delay for comprossor operation.

(cviii) Accurate temp control +/-1°C.

(cix) Provision for fire alarm input.

(cx) Non -Volatile memory.

Supply, assembly and erection of GI sheet with TDF flange rectangular/square duct made out of L shaped hollow profile, duly factory boxed including all accessories such as corner, cleat, carriage bolt, gasket and appropriate sealant on longitudinal joints etc complete with GI sheet of thickness 24 gauge complete all as specified & directed.

Supply, assembly and erection of GI sheet with TDF flange rectangular/square duct made out of L shaped hollow profile, duly factory boxed including all accessories such as corner, cleat, carriage bolt, gasket and apropriate sealent on longitudinal joints etc complete with GI sheet of thickness 22 gauge complete all as specified & directed.

Note: (i) Necessary opening in the brick wall shall be carried out for the installation of supply and return air ducts as the air conditioning is to be carried out in the proposed building without any structural modification and the openings shall be finished properly and matched with surrounding colour.

(ii) The layout of the ducting shall be designed by the contractor through the OEM and the drawing with all details specifications shall be produced to GE for approval before starting of work.

(iii) The contractor shall design, suppply ducts and return ducts based on the room design conditions and detailed drawing alongwith design calculations shall be submitted for the approval of the Accepting Officer. (iv) The heat load arrived is about 22 Tons which is tentive and for quoting purpose only. Any difference in the tonnage of the plant arrived at on plus side to meet the desired conditions will be provided without any extra cost to the department.

Supplying, Installation, Testing and Commissioning of Refrigerant copper piping for 22 TR air cooled package AC with required size from manufacturer (OEM) complete with all fittings such as bends, tees, elbows etc. including cheseling and painting. The pipe shall laid with proper supporting arrangement on wall/ground/floor. Making good of distubed surfaces of walls and provision of suitable size clamps etc.complete all as specified & directed.

Supply, laying, testing and commissionnig of UG LT cables 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded coppper conductor, ISI marked, heavy duty including cable glands, cable lugs in power and control cable with size 4 core 4 Sqmm with and incuding PVC conduit not less than 25mm dia. Cable with end termination for Indoor units with Plug Top, Earthing connection, BMS connectivity etc. (From indoor to outdoor & interconnecting control cabling between ODU and CRC)

Supply, laying, testing and commissionnig of UG LT cables 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded coppper conductor, ISI marked, heavy duty including cable glands, cable lugs in power and control cable with size 2 core 2.5 Sqmm with and incuding PVC conduit not less than 25mm dia. Cable with end termination for Indoor units with Plug Top, Earthing connection, BMS connectivity etc. (From indoor to outdoor & interconnecting control cabling between ODU and CRC)

M & L for duct thermal insulation for Rectangular supply air duct- Thermal Insulation with self adhesive 13 mm thick closed cell nitrile rubber & all joints of the insulation shall be further covered with 50 mm wide 3 mm thick self-adhesive tape made of similar material all as specified and as directed.

M & L for duct accoustic insulation with 25 mm thick self adhesive nitrile rubber (armasound) all as specified and as directed.

M & L for 32mm dia heavy duty PVC pipe as in drain piping with all fittings, supports and clamps including drilling hole in wall, chipping wall etc to conceal and to route the drain pipe. The piping shall be suitably insulated with 19 mm thick Closed Cell foam Class O (Nitrile Rubber) stuck with approved adhesive compound. The insulation shall be covered with glass cloth and pointed with rubberised paint all as specified and as directed.

M & L for 40mm dia heavy duty PVC pipe as in drain piping with all fittings, supports and clamps including drilling hole in wall, chipping wall etc to conceal and to route the drain pipe. The piping shall be suitably insulated with 19 mm thick Closed Cell foam Class O (Nitrile Rubber) stuck with approved adhesive compound. The insulation shall be covered with glass cloth and pointed with rubberised paint all as specified and as directed.

M & L for 50mm dia heavy duty PVC pipe as in drain piping with all fittings, supports and clamps including drilling hole in wall, chipping wall etc to conceal and to route the drain pipe. The piping shall be suitably insulated with 19 mm thick Closed Cell foam Class O (Nitrile Rubber) stuck with approved adhesive compound. The insulation shall be covered with glass cloth and pointed with rubberised paint all as specified and as directed.

S& F air diffuser for the 4-way square supply air ternimal should be in aluminium powder coated construction with easily removble central core & 4-way uniform air distribution. Volume control damper to be of opposed blade, nylon geared with aerofoil blades & blank matt powder coated (Out to out size shall be 24"x24" with full louvers with required duct connection size (as per opproved layouts) & as per approved sample (Color to match architects requirements) all as specified and as directed.

S& F return air diffuser with HEPA filter for the return air terminal which should be in aluminium powder coated construction EP O deg.4 side flange Grill of (900 mm x 200 mm) as per approved layouts & as per approved sample. (Color to match architect's requirements) return air Grill should be with inbuilt Box type volume control damper of opposed blade constructon, nylon geared with aerofoil blades & black matt powder coated complete all as specified and as directed.

M & L for mild steel framed work as in support stands heavy duty painted with two coats of synthetic enamel paint over a coat of red oxide primer (Wall Brackets) suitable for outdoor/indoor units placing ODU's as required by the available location at site complete all as specified and as directed.

M & L for providing canvas connection of suitable size & of approved material for AC system complete all as specified and as directed.

Supply, installation, tesing and commissioning fresh air fan with gravity lourvers assembly complete with suitable power cable with plug top and of capacity 700 cfm 18 mm STP complete all as specified and as directed.

Supply, installation, testing and adjusting of GSS volume control damper within ducts complete with suitable links. Levers blades should be double skinned aerofoil construction and opposed blades should be at 50mm pitch centres. The blades should be mounted in nylon bushes opreated by and interior wheel gear system. Manual quadrant control with position indicator to be provided to enable adjust volume of air as required, complete all as specified and as directed.

Supply, installation, testing & commissioning of Motorised fire and smoke dampers with actuators (FSD) shall be installed in supply air duct when they pass through AHU room walls & as per specfications. The Dampers shal be motor operated with atleast 90 minutes fire rating as per UL 555S Class II for fire and smoke management rated for 90 min as tested by CPRI Roorkee, India Each FSD shall be of multi leaf type low leakeage and shall be tested inthe factory and will be certified by the manufactures in form of the test certificate. The actuator shall br direct coupled spring return type & motorised. Each FSD shall be supplied with matching sleeve (factory supply) and set of retaining angles for installation on wall /slab. Note: The actuator shall be in line with the technical specifications ans shall be maitenance free direct coupled spring return type suitable to work on 24 velectric supply., complete all as specified and as directed.

S & F mild steel collar clamps for fixing along with ducting of AC plant, made out of flat iron of size 40x5mm complete all as specified and as directed.

Supply, installing, testing and commissioning, weather, dust and vermin proof wall mounted LT panel factory made, Indoor type of suitable size so as to accommodate the following accessories, depth not less than 500mm, IP 54 and all as per IE rules, prewired and fabricated with 2mm thick CRCA sheet exoxy power coated double door with aprons, duly powder coated mounted on MS angle iron frame 50x50x6mm welded in shape with two coats of synthetic enamel paint over a coat of red oxide primer including necessary fixing arrangement on wall including connection cable with cable glands, lugs etc and consisting of the following : .

(a) Copper bus bar 300Amps ( 04 Nos) 3 nos for Phase and 01 N mfor neutral duly colour sleeved mounted on epoxy insulator- 01 Set

(b) Incoming

(a) MCCB 100 Amps, 50 KA Breaking capacity adjustable magnetic release (3.5 to 10.0 In), over load release of adjustable thermal release (0.64 to 1.0) -01 No

(c) Outgoing

(a) MCCB 63 Amps, 35 KA Breaking capacity adjustable magnetic release (3.5 to 10.0 In), over load release of adjustable thermal release (0.64 to 1.0) -03 Nos

(b) Voltmeter digital type, 3 phase, 500 VAC -01 Nos

(c ) Ammeter digital type 3 phase 0-200 Amps with CTs-01 Nos

(d) LED phase indicator of Red, yellow, blue-01 set of 03

(e) Panel wiring with suitable capacity of copper conductor cable of 1100 V grade

(f) PCC Foundation (1:2:4) type B1 of suitable size as directed by Engr-in-Charge.

Supply and laying synthetic rubber insulating mat 2mm thick all as per IS 15652-2006 all as specified and as directed.

Supply and fixing De-humidifier strip heaters suitable controls shall be provided for humidity control to keep the humidity 55(+)/(-)5% such that heating should operate automatically including connecting cables, contactors etc. to maintain humidity all as specifeied and as directed.

Supply and fixing GI strip 25x3mm as in earthing complete all as specified and as directed.

SCH 'A PART XII (Miscellaneous B/R and E/M works) Note: This schedule is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only

M &L for submain wiring with 2 single core FRLS PVC insulated unsheathed, multi stranded flexible copper conductor 1100 volts grade cables 2.5 Sqmm drawn through consealed conduit and including PVC conduit heavy grade with and including 1 single core 2.5 Sqmm 1100 V grade FRLS PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified & directed. Note: 3 runs ( 2+1) of single core FRLS PVC insulated unsheathed multi stranded flexible copper conductor and one run of PVC conduit heavy grade shall be measured as one unit.

M &L for submain wiring with 2 single core FRLS PVC insulated unsheathed, multi stranded flexible copper conductor 1100 volts grade cables 4.0 Sqmm drawn through consealed conduit and including PVC conduit heavy grade with and including 1 single core 4.0 Sqmm 1100 V grade FRLS PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified & directed. Note: 3 runs ( 2+1) of single core FRLS PVC insulated unsheathed multi stranded flexible copper conductor and one run of PVC conduit heavy grade shall be measured as one unit.

M &L for submain wiring with 2 single core FRLS PVC insulated unsheathed, multi stranded flexible copper conductor 1100 volts grade cables 6.0 Sqmm drawn through consealed conduit and including PVC conduit heavy grade with and including 1 single core 6.0 Sqmm 1100 V grade FRLS PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified & directed. Note: 3 runs ( 2+1) of single core FRLS PVC insulated unsheathed multi stranded flexible copper conductor and one run of PVC conduit heavy grade shall be measured as one unit.

M &L for submain wiring with 4 single core FRLS PVC insulated unsheathed, multi stranded flexible copper conductor 1100 volts grade cables 10.0 Sqmm drawn through consealed conduit and including PVC conduit heavy grade with and including 2 single core 10.0 Sqmm 1100 V grade FRLS PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified & directed. Note: 6 runs ( 4+2) of single core FRLS PVC insulated unsheathed multi stranded flexible copper conductor and one run of PVC conduit heavy grade shall be measured as one unit.

M &L for submain wiring with 4 single core FRLS PVC insulated unsheathed, multi stranded flexible copper conductor 1100 volts grade cables 16.0 Sqmm drawn through consealed conduit and including PVC conduit heavy grade with and including 2 single core 16.0 Sqmm 1100 V grade FRLS PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified & directed. Note: 6 runs ( 4+2) of single core FRLS PVC insulated unsheathed multi stranded flexible copper conductor and one run of PVC conduit heavy grade shall be measured as one unit.

Supply & fix ceiling fan, 1200 mm (48") sweep with BLDC motor, 5 star rating BEE mark (after assembling the same with the fan hook/box) with the fan hook/box and connecitng up complete with and including electronic fan regulator stepped type, modular type, 2 module flush and with and including three core copper conductor flexible cord of 0.5 sqmm cross sectional area of required length from ceiling rose to porcelain connector block of fan. Make : Havells Cat No ES-60 or equivalent in makes listed in Appendix 'C', complete all as specified and as directed.

S & F LED tube along with CRCA LED Batten complete LED light fitting fixture including LED Tube and Batten, LED Tube fitting consist of Polycarbonate housing with extruded aluminium heatsink for mounting LED chip, LED tube system wattage consist of 18 / 20 W, 140-260V AC, system Lumen output min 1800 Lumen in 18 W and 2000 lumen in 20 W with 5700-6500 K CCT with PF>0.95 CRI>=80 and with <=10 % THD, with Min 2.5 KV Surge protection in Built LED Batten consist of powder coated CRCA box type batten with decorative end caps should be supplied for installing above LED tubes. Make as per Appendix 'C'

S & F 25 Watt LED street light Pressure die cast aluminium alloy for housing (heat sink) for effective thermal management with LED PC lens LED Street Light system wattage consist of 25 Watt ,140-260 V AC, System Lumen Out put min 2550 Lumen in 25 w with 5700-6500 K CCT with PF >0.95 CRI >=70 and with <=10 % THD, with Min 2.5 KV Surge protection in Built and LED Street Light with BIS R Registration number and necessary brackets , GI pipe 32 mm dia medium grade 1.2m, duly bent to shape including provision of clamps of suitable size all as specified and diretced. Make as given in Appx 'C'.

S & F square 2 ft x 2 ft, 36 w-42 w surface mounted bottom opening LED Clean room fitting including, LED Lamp with powder coated CRCA housing and polycarbonate diffuser, LED Fixture system wattage 36 -42 w,140V -260 V AC ,System lumen out put min 3600 lumen in 36 w and 4200 lumen in 42 w with 5700-6500 K CCT with PF>0.95 CRI>=80 and with <=10 % THD, with Min 2.5 KV surge protection in Built complete LED fixture with BIS Mark and R Registration no. Make as per Appendix 'C'.

S & F 2 x 6 w doube head mirror ight LED Batten fixture with IP20 moisture protection, Premium opac glass housing and chrome mounts, LED fixture system wattage of 06 w each, 140V-260V AC, System Lumen output min 600 Lumen in 06 w with 5700-6500 KCCT, all as specified and directed. Make as given in Appx 'C'.

S&F MCB Single pole 240 volts 6 Amps to 32 Amps 10 KA , 'C' series, complete all as specified and directed.

S&F MCB Single pole and neutral 240 volts 6 Amp to 32 Amps 10 KA complete all as specified and directed.

S&F MCB TPN, 415 volts, 63 Amps 10 KA complete all as specified and directed.

S&F MCB TPN, 415 volts, 40 Amps 10 KA complete all as specified and directed.

S&F Blanking plate made of PVC complete all as specified and directed.

Supply & fix PVC body exhaust fan 250mm sweep, 1350RPM, single phase, light weight, white/ivory plastic rust proof body & blades, self opening louvers for protection from birds and rain water, fixing by means of rugged bolts, nuts and washers etc on the round hole cut in wall, including three core copper conductor flexible cord of 0.5sqmm cross sectional area of required length from ceiling rose to porcelain connector block of exhaust fan suitable on working AC, SP 230 V electric supply. Make as listed in Appendix 'C', complete all as specified and as directed.

M& L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick, buried vertically in ground (Earth pit not less than 2.25 metres deep below normal ground level and top edge of the plate not less than 1.5 m below ground level), connected to and including GI strip 32x6 mm by means of bolts, nuts & checknuts and washers etc; GI pipe 40 mm dia medium grade pipe for protection of G.I earth strip, both to be provided to the extent of 7.5 metres, all as shown on electrical plate No 3 of MES SSR-2009 Part-I, other end connected to electrical main switch board (inside the bldg) GI protection pipe buried in ground, laid under floors/plinths or fixed on walls or concealed in walls etc; with provision of mixture of charcoal dust & common salt packed upto minimum 150 mm all around the earth plate , including PCC 1: 2 : 4 type B-1 earth pit with M.S angle iron frame, cast iron cover with locking arrangement, with G.I 20 mm dia medium grade pipe and M.S funnel with wire mesh for watering arrangement, including necessary excavation and earth work in any type of strata & testing on completion.

M& L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick, buried vertically in ground (Earth pit not less than 2.25 metres deep below normal ground level and top edge of the plate not less than 1.5 m below ground level), connected to and including GI strip 25x4 mm by means of bolts, nuts & checknuts and washers etc; GI pipe 40 mm dia medium grade pipe for protection of G.I earth strip, both to be provided to the extent of 7.5 metres, all as shown on electrical plate No 3 of MES SSR-2009 Part-I, other end connected to electrical main switch board (inside the bldg) GI protection pipe buried in ground, laid under floors/plinths or fixed on walls or concealed in walls etc; with provision of mixture of charcoal dust & common salt packed upto minimum 150 mm all around the earth plate , including PCC 1: 2 : 4 type B-1 earth pit with M.S angle iron frame, cast iron cover with locking arrangement, with G.I 20 mm dia medium grade pipe and M.S funnel with wire mesh for watering arrangement, including necessary excavation and earth work in any type of strata & testing on completion.

Design, supply, installing, testing and commissioning of weather, dust and vermin proof LT distribution panel board factory made, outdoor type of suitable size so as to accomodate the following accesories, depth not less than 500mm, IP 54, and all as per IE rules, prewired and fabricated with 2mm thick CRCA sheet epoxy power coated double door with aprons, duly powder coated after seven tank process with fully compartmentalised / modular construction with Bus bar and cable ally, mounted on MS 50x50x6mm angle iron frame and in shape with two coats of synthetic enamel paint over a coat of red oxide primer including necessary grouting in PCC 1:3:6 type C-1 using 20mm graded coarse stone aggregates complete with leg 50cm grouted in ground in PCC at 40cm above ground, including connection cable with cable glands, lugs etc and consisting of the following:- . Note: PCC plinth will be measured and paid separately.

(a) Copper bus bar 200Ampsmounted on epoxy based insulator installed with colour sleevs - 01 Set( 3 Phase and neutral)

(b) Incoming

i) MCCB 100 Amps, FP, 415V, 50Hz ICU 35 KA thermal magnatic release type - 01 No

(c) Outgoing

i) MCCB 40 Amps, FP, 415V, 50Hz ICU, 25 KA thermal magnatic release type- 3 No.

ii) MCCB 63 Amps, FP, 415V, 50Hz ICU, 25 KA thermal magnatic release type- 2 No.

iii) Multi function meter to measure voltage, current, frequency & Power factor- 01 No

iv) LED type indicator lamp (R,Y,B) set of Three. - 01 Nos.

v) LT Danger board

vi) Panel control wiring complete with suitable size copper conductor cable and suitable size gland for LT cables

Note: Panel shall be manufactured by the reputed manufacturer who is possession of type test certificate by CPRI not older than ten years.

M&L for 60mm thick machine pressed pre-cast cement concrete interlocking paver blocks with grey cement and pigment, rubber moulded any shape and size confirming to IS 15658-2006, M-35 grade as in floor/pavement laid over and including 30mm thick crushed stone sand complete all as specified and as directed.

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 110mm and inner dia 95mm polyethylene including coupler and bend with smooth internal and profiled external surface for non pressure under ground cable complete all as specified and as directed.

Supply, laying, testing and commissionnig of UG LT cables 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded aluminum conductor, ISI marked, heavy duty including cable glands, cable lugs in LT panel/MDB in building etc to suit the cable including material and labour for all jointing/connecting material as required size, cables laid in trenches/ducts/under plinth floors passing through pipes etc, fixed on wall complete of following sizes :-

(a) 400 sqmm x 3.5 core

(b) 185 sqmm x 3.5 core

(c) 95 sqmm x 3.5 core

Supply and install following size of perforated MS cable trays including horizontal and vertical bends, reducers, tees, cross members duely painted with two coats of synthetic enamel paints over a coat of red oxide primer and other accessorie as required, duly suspended from the ceiling with and including MS suspenders (10 mm dia threaded rod, anchor fasteners and angle of 40x40x5 mm thick) complete all as specified and as directed.

(a) 300 mm width x 50 mm depth x 1.6 mm thickness

(b) 150 mm width x 50 mm depth x 1.6 mm thickness

Supply, installing, testing and commissioning, weather, dust and vermin proof Feeder Piller box factory made, outdoor type of suitable size so as to accommodate the following accessories, depth not less than 500mm, IP 54 and all as per IE rules, prewired and fabricated with 3.15mm thick CRCA sheet exoxy power coated double door with aprons, duly powder coated mounted on MS angle iron frame 50x50x6mm welded in shape with two coats of synthetic enamel paint over a coat of red oxide primer including necessary grouting in PCC 1:3:6 type C-1 using 20mm graded coarse stone aggregates complete with leg 50cm grounted in ground in PCC at 40cm above ground including connection cable with cable glands, lugs etc and consisting of the following : .

(a) Copper bus bar 300Ampsmounted on epoxy based insulator installed with colour sleevs - 01 Set( 3 Phase and neutral)

(b) Incoming

(a) MCCB 160 Amps, 50 KA Breaking capacity adjustable magnetic release (3.5 to 10.0 In), over load release of adjustable thermal release (0.64 to 1.0) -01 No

(c) Outgoing

(a) MCCB 80 Amps, 35 KA Breaking capacity adjustable magnetic release (3.5 to 10.0 In), over load release of adjustable thermal release (0.64 to 1.0) -03 Nos

(b) Voltmeter digital type, 3 phase, 500 VAC -01 Nos

(c ) Ammeter digital type 3 phase 0-200 Amps with CTs-01 Nos

(d) LED phase indicator of Red, yellow, blue-01 set of 03

(e) Panel wiring with suitable capacity of copper conductor cable of 1100 V grade

(f) PCC Foundation (1:2:4) type B1 of suitable size as directed by Engr-in-Charge.

Note: Panel shall be manufactured by the reputed manufacturer who is possession of type test certificate by CPRI not older than ten years.

Supply, installing, testing and commissioning, weather, dust and vermin proof Feeder Piller box factory made, outdoor type of suitable size so as to accommodate the following accessories, depth not less than 500mm, IP 54 and all as per IE rules, prewired and fabricated with 3.15mm thick CRCA sheet exoxy power coated double door with aprons, duly powder coated mounted on MS angle iron frame 50x50x6mm welded in shape with two coats of synthetic enamel paint over a coat of red oxide primer including necessary grouting in PCC 1:3:6 type C-1 using 20mm graded coarse stone aggregates complete with leg 50cm grounted in ground in PCC at 40cm above ground including connection cable with cable glands, lugs etc and consisting of the following :-

(a) Copper bus bar 300Amps mounted on epoxy based insulator installed with colour sleevs - 01 Set( 3 Phase and neutral)

(b) Incoming

(a) MCCB 200 Amps, 50 KA Breaking capacity adjustable magnetic release (3.5 to 10.0 In), over load release of adjustable thermal release (0.64 to 1.0) -01 No

(c) Outgoing

(a) MCCB 160 Amps, 16 KA Breaking capacity adjustable magnetic release (3.5 to 10.0 In), over load release of adjustable thermal release (0.64 to 1.0) -02 Nos

(b) Voltmeter digital type, 3 phase 0-500 V AC -01 No

(c ) Ammeter digital type 3 phase LED range 0-200 Amps with CTs -01 No

(d) LED phase indicator of Red, yellow, blue-01 set of 03-01 No

(e)Panel wiring with suitable capacity of copper conductorcable of 1100 grade

(f) PCC Foundation (1:2:4) type B1 of suitable size as directed by Engr-in-Charge.

Note: Panel shall be manufactured by the reputed manufacturer who is possession of type test certificate by CPRI not older than ten years.

Design, supply, installing, testing and commissioning of weather, dust and vermin proof LT distribution panel board factory made, outdoor type of suitable size so as to accomodate the following accesories, depth not less than 500mm, IP 54, and all as per IE rules, prewired and fabricated with 3.15mm thick CRCA sheet epoxy power coated double door with aprons, duly powder coated after seven tank process with fully compartmentalised / modular construction with Bus bar and cable ally, mounted on MS 50x50x6mm angle iron frame and in shape with two coats of synthetic enamel paint over a coat of red oxide primer including necessary grouting in PCC 1:3:6 type C-1 using 20mm graded coarse stone aggregates complete with leg 50cm grouted in ground in PCC at 40cm above ground, including connection cable with cable glands, lugs etc and consisting of the following:- . Note: PCC plinth will be measured and paid separately.

(a) Copper bus bar 200Amps-04 Nos for phases and 01 Nos for neutral duly colour sleeved mounted on epoxy insulator-01 Set

(b) Incoming

i) MCCB 100 Amps, FP, 415V, 50Hz ICU 35 KA thermal magnatic release type - 01 No

(c) Outgoing

i) MCCB 63 Amps, FP, 415V, 50Hz ICU, 25 KA thermal magnatic release type- 2 No.

ii) Street light timer switch of ccapacity 5KW-01 No

iii) Multi function meter to measure voltage, current, frequency & Power factor- 01 No

iv) LED type indicator lamp (R,Y,B) set of Three. - 01 Nos.

v) LT Danger board

vi) Panel control wiring complete with suitable size copper conductor cable and suitable size gland for LT cables

Note: Panel shall be manufactured by the reputed manufacturer who is possession of type test certificate by CPRI not older than ten years.

Sypply, laying, jointing and testing of heavy grade GI pipe Type C for air compressor line of dia 25mm including painting and fixed with and inclding suitable size clamps and supports, colour coding all as specified.

Sypply and fix ball valve heavy grade of size 25mm bore suitable for air compressure line of dia 25mm bore all as specified.

SCH 'A' PART XIII : Manning and operation of AC plant (PHASE-II WORK)

Out sourcing for Manning and Operation of Air Conditioning system as provided in Sch 'A' Part XI , in one shift of 08 hours per day by deploying 01 operator (ITI qualified) per shift of 08 Hrs including working on Saturday, Sunday and Holidays complete all as specified and as directed.

Note for BOQ item No - 5.1 : a) The contractor shall quote the rates for M&O only as comprehensive maintenance of the plant i.e. replacement of defective parts & providing spares, all consumables during this period of 02 (two) years from completion of phase -I shall be covered under defect liability period.

b) The work order of outsourcing for M & O shall be placed by GE & no price adjustment during whole period due to change in minimum fair wages shall be admissible.

c) The AC system will be operated for 08 hours in 01 shift per day, unless otherwise specified by the Engineer-in-Charge / GE.

d)The operator being deployed in the work shall have minimum qualification of ITI (Refrigeration & AC) / ITI (Mechanical) with 02 years experience in the relevent field. Necessary qualification certificate and experiance certificate shall be produced for verification of Engineer-in-Charge & get the approval before deploying for works.

e) Proper and effeicient functioning of the plant must be ensured through regular inspection by qualified Engineer bi-monthly preferably by OEM or by his authorised agency.

f) The contractor shall carry out routine maintenance as per procedure mentioned in the PS. Any repair/maintenance of minor spare parts covered under routine maintenance schedule shall be carried out by the contractor by engaging his labour.

Samruddhi Construction

shah construction

Mukund Engineers and Contractors