Renovation works to the Engineering section at Corporation main office in ward No 82, Central zone.

Removing the existing damaged false ceilings as per the direction of departmental officers

Supply and fixing of Doors Using 32mm flush door,1mm laminate on either sides, First quality Teak wood trimmings, Brass Oxidized hinges, Tower bolt,Lock,Handle,Door stopper, with Door closer Teak wood surface is stained and finished in semi glossy melamine etc, complete as per standard specifications

Supply and providing false ceiling arrangements using 12.5 mm tk tapered edge Gypsm Board False ceiling confirming to IS 2095 including providing and fixing of frame work made up of special sections power pressed from MS Sheet and Galvanised Zinc Coating 600 micron as per IS 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm tk.with flanges of 12 mm and 37 mm providing and fixing at all height false ceiling of at 1200 mm c/c on flanges to the ceiling with dash fastener 12.5 mm dia x 40 mm long with 6 mm dia bolts to the hanger of 25 mm x 25 mm 5mm of required length and other end of angle hanger being fixed with nuts and bolts to G.I. Channels 45 mm x 15 mm x 0.90 mm running at the rate of 1200 mm c/c to which the ceiling section 0.5 mm tk. bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 at 450 mm c/c shall be fixed in a direction perpendicular to G.I Channel with connected clips made out of 2.64 mm dia x 230 mm long G.I.Wire at every junction including fixing the gypsm board with ceiling section and perimeter channels5 mm tk. 27 mm high having flanges of 20 mm and 30 mm long,theperimeter of ceiling fixed to wall /partitions with the help of rawl plugs at 450 mm c/c with 25 mm long drive -all screws at 230 mm intervals including jointing and fixing to a flush finish of tapered and square edges of the Gupsum Board with recommented filler,paper tapes,Finisher and twp coats of primer suitable for Gypsum Board as per manufactures specification and also including the cost of making openings for light fitting ,Grills Diffusers,cutouts made with frame of perimeter channels suitably fixed all complete as per drawings and specification and direction of th departmental officers .(excluding cost of paintnig)

Providing Cornice Work for Gyp Board False Ceiling as per the direction of th departmental officers

painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Providing Wall Panelling using one side teak wood sheet with melamine polishing with following specification. The frame using aluminium tubular section of size 50mm x 25mm x 2mm thick fixing horizontally and vertically in position with wall at interval of 0.60m in both diretions, fixing water proof plywood of 12mm thick over the aluminium frame work with necessary screws. One side teak wood sheet of 3.5mm thick will be fixed over the plywood using fevical and finishing with melamine polishing and the rate inclusive of conveyance to site and labour charges and as directed by the Departmental Officers. The design pattern, water proof plywood, OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work etc., complete

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Supply and Run of 4 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.

Supply and Run of 3 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour

Supply, installation and termination of Data points and LNA cabling and other required CAT6 UTP cables and Optical fiber cables along with accessories as per instruction of departmental officers including all cost etc complete.