Construction of Degree College at Kakryal,Katra Distt. Reasi

Amount

Part A

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (Exceeding 30cm in depth, 1.5mtr in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed (50% all kind of soil,20%ordinary rock and 30% hard rock (Blastic prohibitd.

Removal / disposal of surplus excavation earth by mechanical means upto a lead of 1km.

Extra for every additional lift of 1.5 mtr or part thereof in all kinds of Soil

Providing and lying in position cement concrete of specified grade excluding the cost of centring and shuttering- all works upto plinth level. (crushed Stone 40 mm nominal size) 1 cement 4 coarse sand: 8 graded, stone aggregates 40mm size crushed Stone.

Providing and laying in position specified grade of reinforced cement concrete M 20 Mix excluding the cost of centering, shuttering, finishing and reinforcement- All works upto plinth level: 1:1:5:3 (1 cement: 1:5 coarse sand:3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts ans sturts, etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of 1:3:6 grade (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) excluding the cost of centring andshuttering- All work upto plinth level.

Brickwork with common burnt clay F.P.S (non modualar) bricks of class designation 75 upto plinth level in 1cement : 4 fine sand mortar.

Providing and laying damp-proof course 50 mm thick with cement concrete 1: 2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 nominal size) crushed aggregate

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Brickwork with common burnt clay F.P.S (non modualar) bricks of class designation 75 in superstructure in 1cement : 6 fine sand mortar.

Half brick masonry with bricks of class designation 75 in foundations and plinth, and superstructure upto floor V level in Cement mortar 1:4 (1 cement: 4 coarse sand).

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15 degree, landing balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding cost of centring, shuttering, finishing and reinforcement. 1 cement: 1.5 coarse sand : 3 graded stone aggregates 20mm nominal size.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Cetring and shuttering including strutting, propping etc and removal of the form work for:

Foundation, footing, bases of columns

Suspended floors, roofs, landing, balconies and access platforms.

columns, Pillars,Piers, Abutments, Posts and Struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Edge of slabs and break in floors and walls Under 20 cms wide.

Retaining Walls, Return Walls, walls (any thickness) including attached pilasters, buttresses, plith and string courses etc.

Weather shade, chajjas, corcels etc., including edes.

Stairs, (excluding landings) except spiral staircases

Extar for additional height in centring, shuttering where ever required with adequate bracing, propping etc, including cost of de-shuttering and decentring at all levels, over a height of 3.5 m, every additional height of 1 metre or aprt thereof (Plan area to be measured)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying Cement Concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded brick aggregate 40 mm nominal size) in retaining wall/return wall, columns etc. excluding cost of centering and shuttering, all work upto floor V level

6mm cement plaster to ceiling of mix 1 : 3 (1 cement: 3 fine sand)

15mm Cement plaster on the rough side of single or half brick wall of mix 1 : 6 ( 1 cement : 6 coarse sand)

15mm Cement plaster on the rough side of single or half brick wall of mix 1 : 4 ( 1 cement : 4 coarse sand)

12mm Cement plaster of mix 1 : 6 ( 1 cement : 6 fine sand)

15mm Cement plaster 1 : 3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

18mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1 : 5 (1 cement: 5 coarse sand) top layer 6mm thick with cement mortar 1 : 4 (1 cement: 4 fine sand) for 4cm width.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Add or deduct for plaster drip course/groove in plastered surface of moulding to R.C.C. projections.

Making of Grove 12mm x10 mm between Brick and RCC.

Providing and fixing tiled False Ceiling of approved materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanised @ 120 gms/sqm both side inclusive ) consisting of main 'T' runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross 'T' of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main "T" at 600mm cente to centre to form a grid of 1200 x 600mm and secondary cross "T" of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using Gl slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm Gl adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer in-charge. Gl Metal Cei!ing Lay in perforated Tegular edge globalwhite color ti.[gs of size 595x595 mm and 0.5.mm thickwith 8 mm drop; made of Gl sheet having galvanizing of1 00 gms/sqm .(both sides inclusive) and 20% perforation area with 1.8 mm d!a holes and having NRC (NoiseReduction Coefficient) of 0.5. electro statically polyesterpowder coated of thickness 60 microns (minimum), including factory painted after bending and perforation,and backed with a black Glass fiber acoustical fleece.

Providing and laying 18mm thick Granite of any colour and shape (Area of slab over 0.5 sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Providing and laying full-body vitrified premium quality floor tiles of 60x60cm size (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make of Somany, Kajaria,or equivalent make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying full-body vitrified premium quality floor tiles of 60x120cm size (thickness to be specified by the manufacturer) with water absorptions less than 0.08%and conforming to IS : 15622 of approved make of Somany, Kajaria,or equivalent make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Eningeerin-Charge in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarse sand) and jointing wtih grey cement slurry@ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ceramic floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITC.O, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4 coa.rse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying 16mm thick Granite of any colour and shape (Area of slab over 0.5 sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Providing and laying 18mm thick Granite of any colour and shape (Area of slab over 0.5 sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for stairs steps and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Extra for providing edge moulding to 18 mm thick Granite stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size and shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble I stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Precast terrazo tiles 22mm thick with graded marble chips of size upto 12 mm laid in floors, and landing, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete with precast tiles on 20 mm thick bed of cement mortar 1 :4 ( 1 cement : 4 coarse sand) Medium shade using 50% white cement and 50% ordinary cement.

Precast terrazo tiles 22mm thick with graded marble chips of size upto 12 mm in skirting and risers of steps not exceeding 30 em in height on 12 mm thick cement plaster 1:3 (1 cement: 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of:

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) .Medium shade using 50% white cement and 50% ordinary cement.

Cement concrete flooring 1:2:4 ( 1 cement: 2 coarse sand 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.50 mmthick with 20mm nominal size stone aggregate.

Cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement.

Providing and fixing of 12mmthick GRC wall cladding (Tiles) of pattern stone castie (size 4" x10")on exterior wall/ surface.Unistone make as per the approved sample .All complte as per architectural drawings and the directions of Engineer-in -Charge.

Providing and laying integral cement based water proofing treatment including prepration of surfaces as required for treatment of roofs, balconies, terracies etc consisting of following operations.(a) applying a slurry coat of neat cement using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement: 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs) (c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge.(d) finishing the surface with 20mm thick jointless cement mortar of mix 1 :4(1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved byEngineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finially finishing the surface with trowel with neat cement slurrv and making pattern of 300x300mm/sq 3mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge.With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment to vertical and horizontal surface of depressed portions of W.C.kitchen and the like consisting of :(I) 1st course of applying cement slurry @ 4.4kg/sqmmixed with water proofing compound conforming to IS:2645 in recommended proportions including rounding ofJunctions of vertical and horizontal surface.(II) lind course of 20mm cement plaster 1:3 (1 cement: 3coarse sand) mixed with water proofing compound in recommended proportions including rounding of Junctionsof vertical and horizontal surface. (Ill) course of applying blown or/ residual bitumenapplied hot at 1.7 kg. per sqm of area.(IV) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 1 OOmm wide and pastedto each other with bitumen @ 1. 7 kg/sqm.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.110 mm diameter

Providing and fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised- Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 1 0 mm gap for thermal expansion.

Coupler 110mm.

Single tee with door 110 x 110 x110mm

Bend 87.5* 110mm

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75 including grouting with cement mortar 1:4 (1 cement: 4 fine sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Sal wood

Providing 40x5 mm flat iron hold fast 40 em long including fixing to frame with 1 Omm diameter bolts, nuts and wooden plugs and em beddings in cement concrete block 30x1 Ox15 em 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size )

Providing and fixing 35mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. in Second Class Deodar Wood

Providing and fixing 35mm thick wire guage shutters using galvanised M.S. wire guage of average width for aperture 1.4 mm in both direction with wire of dia 0.63 mm for doors, windows and clerestory windows with ISI marked M.S pressed but hinges bright finished butt hinges of required size with necessary screws, in Second Class Deodar Wood

Providing and fixing Glass panes weighing 13.75 kg/sqm with Deodar wood Fillets.(Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1stclass hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc.

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.

Providing and fixing stainless steel tower bolt ISI marked of approved make with necessary screws etc. complete :

Providing and fixing stainless steel Aldrops ISI marked of approved make with necessary screws etc. complete : 250X14 mm

Providing and fixing stainless steel Handles ISI marked of approved make with necessary screws etc. complete :

Providing and fixing stainless steel hanging floor door stopper lSI marked with necessary crews etc. complete .Twin rubber stopper.

Providing and fixing stainless steel M.S. hasp and staple (Safety type) lSI marked with necessary screws etc. complete.

Providmg and fixing IS: 3564 marked Aluminium extruded section body tubular type universal hydraulic door closer,(having superior brand) embossed on the body, door weight upto 36-80 l<g and door width upto 700-1000 mm with double speed adjustment with necessary accessories and screws etc.complete :

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary ccessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

P/F of HPL (High pressure laminate) for front faced of building with Aluminium channel and PVC cap screw in all respect including scaffolding (complete job)

Providing and fixing of stainless steel curtain rods with brackets of 25 mm dia (heavy duty) including all fittings and fixtures.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Wall Painting with plastic emulsion paint of approved lj brand and manufacture to give an even shade including primer coat with cement primmer. Two or more coats on new work

Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 litre/1 Osqm over and including base Coat of water proofing cement paint app-lied @ 2.20kg/1 Osqm)

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work ( wood work).

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade with ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanised iron/steel works. New steel work (two or more coats)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- Charge (glazing, panelling and dash fasteners to be paid for separately.)

For fixed portion Powder coated aluminium (minimum thckness of powder coated 50 microns).

For shutters of doors, windows & ventilators including providing and fixing hinges I pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber I neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminium (minimum thickness of powder coated 50 microns).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) With float glass panes of 5.50 mm thickness (weight not less than 13 .. 50 kg I sqm).

Providing and fixing 12mm thick prelaminated particle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc.Pre-laminated particle board with decorative lamination on both sides. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo em,possed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in-charge.With Stainless Steel cover plate minimum 1.25 mm thickness. floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot" and single piece M.S. sheet outer box with slide plate etc. complet~ as per the direction of Engineer-in-

Providing and fixing structural glazing on required portion of the building with aluminium section (12 gauze using 5.5mm toughen glass with all necessary fittings) as per direction of Engineer-in -charge.

Maintaining 50mm joint right from foundation to top and allowing its free moment throughout the life span of structure "Providing / Supply of dura Board HD 100, 50mm, premounded Compressible filler board in black colour manufactured by the supreme industries Ltd. or equivalent conforming to MORTH specifications (clause 1015)having minimum density 95kg/cum,non staining with less than 1% water absorption and compression recovery 93% minimum as per specifications' in the joint through and through ( foundation to top) in brick masonary ,columns and beams.

Sealing of joint 50mm. Clean the both the side and apply Master Brace ADH 2200 adhesive throughly on the clean surface along the joint with spatula and thickness should be 1mm-2mm. Place the Master seal 1930 10mm on the ADH 2200 on the both sides keeping the centre totally for free

Carriage of material Mechanical Transport including loading/un loading and stacking at site complete.

Stone Aggregate below 40mm size for an average lead of 10 Km.

Sand for an average lead of 10 Km.

Bricks for an average lead of 10 Km.

Brick bats (size 25mm to 115mm ) for an average lead of 10 Km.

Part "B" ( Plumbing)

Providing and fixing white vitreous china pedestal type water closet ( European type) with seat and lid ,10 litre low level white vitreous china flushing cistern and CP flush with fittings, C. I./M.S. brackets 40mm bend diameter flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with lSI marked white solid plastic seat and lid. with white vitreous china flushing cistern & C. P. flush bend.

Providing & Fixing of white vitreous china under counter oval wash basin / circular basin Hindware , Jaquar ,Parko or equivalent with CP brass waste assembly, CP cast brass bottle trap with extension piece 450mm long CP copper connections pipes wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted , nuts, washers, cutting and making good the walls floors.

Providing and fixing wash basin with C. I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing CP single liver extended basin mixer ( height 85mm) with out popup waste system with 450mm long Braided Hoses and brass nut with all fittings and accessories as per direction of Engineer-in -charge.

Providing and fixing white vitreous china flat back half stall urinal basin of 580x380x350mm with Flat White P.V.C automatic flushing cistern, of approved make with fittings, C.I./M.S. brackets, standard size of C.P. brass flush pipe, spreaders with unions and clamps complete, (all in C.P. brass) with waste fitting as per IS:2556, C.l trap with outlet grating and other couplings in C.P brass including painting of fittings and brackets, cutting and making good the walls and floors wherever equired. Range of three half stall urinals with 10 litre white P.V.C automatic flushing cistern of approved quality.

Providing and fixing Salem Stainless Steel A lSI 304 (18/8) kitchen sink as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required .

Kitchen sink with drain board 510x1040mm bowl depth 225mm( Dry canteen/ kitchen).

Kitchen sink without drain board 610x460mm bowl depth 200mm( Pantry ).

Providing and fixing , testing and commissioning of C.P brass single hole sink mixer with CP wall flange, swinging spout complete as required and making good as per direction of Engineer-in Charge

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931( 15 mm nominal bore) Make Hindware , Jaquar ,Parko or equivalent .

Providing and fixing Stainless Steel robe hook fixed to wall/ door with plastic rawl plugs and C.P brass screws including cutting and making good the wall wherever required as per direction of Engineer-in charge.

Providing and fixing stainless steel soap dish holder with all fittings and fixtures of approved make (complete) of approved make..

Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms. compete as per directions of Engineer-in charge.

Providing and fixing 600x450mm beveled edge mirror of sperior glass (of approved quality) complete with 6mm thick hard board ground fixied to wooden cleats with CP brass screws and washers complete.

Providing & fixing stainless Steel towel rail with all fittings and fixtures of approved make (complete) of approved make.

Providing and Fixing stainless Steel towel ring round of approved make of Jaquar, Cera or equivalent.

Providing and Fixing 600120x5mm glass shelf with edges round of supported on anoised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs, etc complete.

Providing and fixing toilet paper holder stainless Steel .

Providing and fixing 15MM dia C.P. brass Bib cock of approved quality conforming to IS: 8931 standards and weighing not less than 690 gms.(make of Jaquar, Cera or equivalent).

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.(make of Jaquar, Cera or equivalent).

Providing and fixing C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 89319(15 mm nominal bore) make of Jaquar, Cera or equivalent.

Sub Head - II-Water Supply

Providing and fixing G.I. pipe to IS: 1239 (Heavy class) with G.I. fittings upto 150 mm dia & above shall be M.S.7 mm thick conforming to I.S. : 3989 including synthetic enamenl paints of approved quality & shade over a coat of approved priming coat (shade as per colour code) and clamps and flanges including cutting and making good the walls complete. For rising mains, suction and delivery headers. ( Internal work - Exposed on wall)

35 mm dia nominal bore of heavy class

35 mm dia nominal bore of heavy class

Providing and fixing G.I. pipe to IS: 1239 (Heavy class) with G.I. fittings upto 150 mm dia & above shall be M.S.7 mm thick conforming to I.S. : 3989 including synthetic enamenl paints of approved quality & shade over a coat of approved priming coat (shade as per colour code) and clamps and flanges including cutting and making good the walls complete. For rising mains, suction and delivery headers. ( Internal work - Exposed on wall)

20 mm dia nominal bore of heavy class

25 mm dia nominal bore of heavy class

Providing and fixing G.l. pipes complete with G.l. fittings including trenching and refilling etc. (external work)

20 mm dia nominal bore of heavy class

25 mm dia nominal bore of heavy class

32 mm dia nominal bore of heavy class

32 mm dia nominal bore of heavy class

Providing and fixing of Brass Check Valve of approved make complete. 25mm

Sub Head - III-Drainage System

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (Exceeding 30cm in depth, 1.5mtr in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed:

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design.

Inside size 90x80 cm and 45 cm deep including C.l. cover with frame (light duty) 455x610 mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With F.P.S. bricks with class designation 75 & with Crushed stone aggregate.

Inside size 90x80 em and 60 em deep including C.l. cover with frame (light duty) 455x610 mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)

Providing and fixing PVC pipes 6kg/cm2 pressure excluding pvc fittings, jointing with adhesive/seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion of approved make Supreme/Finolex/ Astral or equilant.

110 mm dia

80 mm dia

160 mm dia

Providing and fixing PVC plain Bend of approved make Supreme/Finolex/ Astral or equilant complete.

110 mm dia

160 mm dia

Providing and fixing PVC Floor Trap of approved make Supreme/Finolex/ Astral or equilant complete.

110 mm X 80 mm

160 mm X 110 mm

Providing and fixing PVC Plain Tee of approved make Supreme/Finolex/ Astral or equilant complete.

110 mm X 80 mm

Providing and fixing PVC Door Bend of approved make Supreme/Finolex/ Astral or equilant complete.

Providing and fixing PVC Door Tee of approved make Supreme/Finolex/ Astral or equilant complete.

Providing and fixing PVC Coupler of approved make Supreme/Finolex/ Astral or equilant complete.

Providing and fixing PVC Clamps for pvc pipes of approved make complete.

Providing and fixing PVC Cowl of approved make complete.

Providing and fixing C.P Jali of approved make complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) (1000 ltr. Capacity 15 No.).

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks.

SUB HEAD - WATER SUPPLY, DRAINAGE, PUMPS & EQUIPMENT

Supply, assembly, erection, testing and commissioning of pumping system comprising the following:

Vertical/Horizontal centrifugal pumps (1 Working + 1 Stand-by) with mechanical seal, SS Volute casing and SS impeller connected to suitable capacity TEFC induction motor suitable for 415 ± 10 % volts, 3 phase, 50 cycles A.C. supply with 100 mm dia. pressure gauges including MS skid and mounting of the pumps on the skid. (Motor to be of the same make as the pump) (wilo,ebara and matherplatt etc.)

Pump Capacity 180 lpm, at 30 m head (1 working + 1 standby) (Domestic water relift pump).

PART-B ELECTRICAL

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor singlecore cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthingthe point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group B

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4.0sq. mm + 1 X 4.0sq. mm earth wire

2 X 6.0 sq. mm + 1 X 6.0 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 16.0 sq. mm + 2 X 6.0 sq. mm earth wire

TV Cable in existing conduit :

Supplying and drawing co-axial TV cable RG-6 grade, 0.7mm solid copper conductor PE Insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/recessed steel/PVC conduit as required.

S/F PVC Conduit

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of Recessed conduit as required

S/F modular boxes, base and cover plate :

Supplying and fixing following size/modules , GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 module ( 75mm x 75mm)

3 module ( 75mm x 75mm)

4 module ( 125mm x 75mm)

6 module ( 200mm x 75mm)

S/F power plug point modular type accessories:

Supplying and fixing on exisitng GI Box modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc as required.

Supply, Installation, Testing and commissioning of Modular Type Power Outlet Unit for AC / Geyser 572154 of Legrand or equiv in MK( Aspect) /Schneider Zencilo including supply and fixing GI box for mounting of Power Unit.

S/F Modular type switch/socket :

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

5/6Amp Switch

2 way 5/6 Amp 2 way Switch

3 pin 5/6 Amp socket outlet

Telephone socket outlet

TV antenna socket outlet

S/F modular type electronic fan regulator:

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F modular type blanking plate:

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

S/F ceiling rose :

Supplying and fixing 3pin 5 Amp ceiling rose on the existing junction box/wooden block including connection etc. as required.

S/F call bell/ Buzzer

Supplying and fixing call bell / buzzer suitable for D.C./A.C. single phase , 230volts, complete as required.

ITC fluorescent fitting directly on surface :

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

ITC Ceiling Fan :

Installation, Testing and commissioning of ceiling fan, including wiring the down rods of standard length ( upto 30 cm) with 1.5sq mm FR PVC insulated, copper conductor , single core cable etc. as required including providing and fixing phenolic laminated sheet cover on fan box etc. as required

Numbering of Fan/Fittings :

Numbering of ceiling fan/exhaust fan / fluorescent fittings as required.

ITC exhaust fan upto 450mm sweep:

Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

Fixing louvers/shutters for exhaust fan:

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

S/F Prewired TP MCB DB:

Supplying and fixing following way , sheet steel, IP 43 MCB distribution board, 415/230 volts, on surface/recess, complete with , terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc. as required.( But without MCB/RCCB/Isolator)

2 Rows X13 modules, Double door

3 Rows X13 modules, Double door

4 Rows X13 modules, Double door

S/F 'C' series , SP MCB:

Supplying and fixing 5 amps to 32 amps rating, 240 Volts, 'C" series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

S/F 'B' Series, SP MCB blanking plate

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, MCB, 10kA, Class 3 with integral label holder in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

P/F M.V. danger notice plate :

Providing and fixing M.V. danger notice plate of 200mm x 150mm , made of mild steel, at least 2 mm thick , and viterous enamelled white on both sides, and with inscription in single red colour on front side as required.

S/L 8 SWG copper wire in ground:

Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required.

150mm dia R.C.C. Pipe

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

upto 35sq.mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

upto 35sq.mm

Above 185 sq. mm and upto 400 sq. mm

Supply of 1.1kV Grade XLPE Insulated PVC sheathed Aluminium Armoured cables conforming to IS 7098 Part-II of following ratings conforming to IS 7098 Part-1 with Latest Amendments

3.5C X 400 sq. mm

3.5C X240 sq. mm

4Cx 16sqmm

S/M LV/MV cable end termination:

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as required

3½ X 400 sq. mm (82mm)

3½ X 240 sq. mm (62mm)

Supplying and fixing following modular Bell Push on the existing modular plate & switch box including connections but excluding modular plate etc. as required

Supply of following LED lighting fixtures :

19W( Maximum) 4ft LED Surface Mounted light fixture 2000 lumens having minimum system lumen efficiency of 100 Lumens per watt equivalent to Endura LED BN108C 6500K, L70 40000hrs of Philips /Trilux/GE

38W( Maximum) 4ft LED Surface Mounted light fixture 4000 lumens having minimum system lumen efficiency of 100 Lumens per watt equivalent to Endura LED BN108C 6500K, L70 40000hrs of Philips /Trilux/GE

12W ,1100 Lumens ( system output), surface mounting having CRCA body, IEC compliant driver LED Fixture SM200 Cirrus Mini Pro of Philips/Trilux/GE

15W ,900 Lumens ( system output), surface mounting having dies cast aluminium housing and heat sink, IEC compliant driver LED Fixture SM518C Cirrus Mini of Philips

10W LED Endura Bulkhead IP66 WT202W of Philips/Trilux/GE

30W ( Maximum) 2ftx2ft Dimmable LED Recess mounting Light Fixture 3000 Lumens having minimum system lumen efficiency of 100Lumens/watt equivalent to RC380B LED 30S 6500 PSD OD of Philips

Supply of 1400mm sweep 230V 50Hz celing fan with double ball bearing with low power consumption

Supply of following sizes of heavy duty exhaust fan as per approved makes

300mm Sweep

Measurable quantities may vary at the time of actual execution of the work and shall be allowed as per actual with in the cost.

RAQ INFRA

M/s Kanhaiya Constructions

M/S CONSTRUCTION ENGINEERS

Ghulam Mohammad Bhat