Loading
Loading…
Loading…
Tender Value
₹9.6 Cr
EMD Value
₹19.2 L
Closing Date
6 Jul 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (WMS)
DCECSPPRYJ
17 conditions · 4 needing a document upload
MINIMUM ELIGIBILITY CRITERIA (FINANCIAL): The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Technical Eligibility Criteria:
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
(1)In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for (1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Note for Item no 1: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Defination of Similar Work :- Any Civil Engineering Work, which includes RCC work among other works.
12 conditions · 5 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Contractor will clear/clean the work site after completion of the work, to the satisfaction of site engineer.
In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned tax authority.
Special Conditions of Contract uploaded in Document Upload Section will form part of these Special Condition.
One qualified graduate engineer when cost of work to be executed is Rs 200 lakhs and above and One qualified diploma holder engineer when cost of work to be executed is more than 25 lakhs but less than Rs 200 lakhs. In case the Contractor fails to employ the Engineer, as aforesaid, he shall be liable to pay liquidated damages at the rates, as prescribed in the tender documents.
Execution of various activities in connection with Production and Handling of sleepers at CSP/SFG/PRYJ.
74-W-CSP-26-27-05
74-W-CSP-26-27-05
Open
Works - General
26 Months
Prayagraj, Uttar Pradesh
₹0
₹19.2 L
6 Jul 2026
13 Jun 2026
22 Jun 2026
35 items across 4 schedules · ₹2,16,90,666.9 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | 60 Kg Level Xing Wider, Guard Rail Wider, SEJ/TW-SEJ. Preparation, Casting, De- moulding and Feeding of Aggregates. Cleaning of moulds and benches, oiling of moulds, fitting of end plates, putting HTS wire strands, fixing SGCI Inserts & Dowels, fixing Wedges and Barrels, fixing rod and dowel cap e t c . Casting of sleepers in the already prepared benches using high frequency shuttering vibrator at appropriate locations. Casting cubes for steam curing and water curing. Pulling casted benches with the help of pulling hoist and putting the same in the steam chamber etc. Work includes cleaning of mixer & distributor. De-moulding of PSC sleepers from sleeper mould including cutting of HTS wire at sleeper ends, grinding of inserts if required to suit the dimensional requirements, numbering/ marking on sleepers and cleaning of inserts and dowel holes, feeding of demoulded benches up to roller bed of preparation area. Feeding of aggregate from stacks to mixer hopper and leading of cement from store to production shed, cutting of cement bags and feeding in hopper as per spl. Condition. Handling of demoulded ordinary/special PSC sleeper to curing tank after end painting by anticorrosive paint. Taking out water cured sleepers, again end painting by anticorrosive paint and stacking at nominated location in stacking yard including testing for electrical resistance for their fitness for use in track circuited area as per special conditions to the satisfaction of Engineer in charge. | Numbers | 32000.00 | 140.96 | 45,10,720 |
| 2 | 60 Kg. 1 in 8.5 T/Out Sleepers Preparation, Casting, De-moulding and Feeding of Aggregates. Cleaning of moulds and benches, oiling of moulds, fitting of end plates, putting HTS wire strands, fixing SGCI Inserts & Dowels, fixing Wedges and Barrels, fixing rod and dowel cap etc. Casting of sleepers in the already prepared benches using high frequency shuttering vibrator at appropriate locations. Casting cubes for steam curing and water curing. Pulling casted benches with the help of pulling hoist and putting the same in the steam chamber etc. Work includes cleaning of mixer & distributor. De-moulding of PSC sleepers from sleeper mould including cutting of HTS wire at sleeper ends, grinding of inserts if required to suit the dimensional requirements, numbering/ marking on sleepers and cleaning of inserts and dowel holes, feeding of de-moulded benches up to roller bed of preparation area. Feeding of aggregate from stacks to mixer hopper and leading of cement from store to production shed, cutting of cement bags and feeding in hopper as per spl. Condition. Note: Total sleepers length of 1 in 8.5 Turnout Sleepers put together are 225.84 linear meters. Contractor will also be asked to do the work in connection with Derailing Switch set, 1 in 12 Turnout set and Scattered Sleepers etc. as well under this item, for which payment will be made on pro-rata basis as per the linear meters casted for respective lay outs (i.e. Rate of one set 1 in 8.5 Turnout Sleepers (X) Layout Length of particular type of Turnout Sleepers / 225.84 meters). Handling of demoulded 1 in 8.5 T/out PSC sleepers to curing tank after end painting by anticorrosive paint. Taking out water cured sleepers, again end painting by anticorrosive paint and stacking at nominated location in stacking yard as per instruction of Engineer in charge. Laying of 1 in 8.5 T/Out PSC sleepers on linking bed in proper sequence, linking of turnout sleepers to correct layout for inspection. Delinking the inspected sleeper sets and stacking them at nominated places including testing for electrical resistance for their fitness for use in track circuited area as per special conditions to the satisfaction of Engineer in charge. Note- However for this item deduction will be made @ 3.32% of accepted rate in case of isolated turnout sleepers. | Set | 674.00 | 32,080.74 | 2,16,22,418.76 |
| 3 | Supply & Fixing of 6 mm dia. MS Rod stirrups in sleeper to be casted vide item NS-1B. Note- 1: Length of one set (1 in 8.5 T/O) = 225.84 m. Total length of 120 sets = 674 x 225.84 = 152216.16 mtrs (Consumption of 6 mm dia. MS Rod in one set of 1 in 8.5 T/O = 970 nos. each 770 mm length). Payment of this item will be made for consumption per set. Note-2: Binding wire required for binding of stirrups will have to be provided by contractor for which nothing extra will be paid. | Metre | 152216.16 | 89.43 | 1,36,12,691.19 |
| 4 | Casting of C.C. block of Hexagonal or any other shape as per requirement. Note: Mould for the blocks will be supplied by railways free of cost at the factory premises. | Numbers | 2400.00 | 5.24 | 12,576 |
| 5 | Manufacturing and supply of Wedges capable of holding 3 x 3mm HTS wire strand without permitting any slip/fail (When tensioned up to breaking load of 38.25 KN) and capable of giving service life minimum 20 uses as per drawing No. CSP/ALD/1166/01 as per tender schedule. Wedges (One set comprises of 2 Nos. wedge pieces). | Set | 64000.00 | 19.99 | 12,79,360 |
| 6 | Manufacturing and supply of Barrels capable of holding 3x3mm HTS wire strand without permitting any slip/fail (When tensioned up to breaking load of 38.25 KN) and capable of giving service life minimum 20 uses as per drawing No. CSP/ALD/1166/01 as per tender schedule. | Numbers | 32000.00 | 21.61 | 6,91,520 |
| 7 | Whitee /Putty | Kg | 200.00 | 19.89 | 3,978 |
| 8 | Providing and fixing guide rod 25 mm dia, 350 mm long and vertical strips 400 x 65 x 10 mm with one hole 25 mm dia for rectification of stress benches (01 Job = 02 nos guide rod, 02 nos vertical strips, 02 nos side cleat) | Job | 200.00 | 471.93 | 94,386 |
| 9 | Providing & fixing of insert supports size 12mm x 12mm, Length 80 mm (M.S. Square). | Numbers | 1600.00 | 19.59 | 31,344 |
| 10 | Providing & fixing of vibrator cleat size (50 x 50 x 6) mm (M.S.Angle) length 100 mm | Numbers | 1600.00 | 57.96 | 92,736 |
| 11 | Providing & fixing of Top-bottom holding box (475 x 75 x 6) mm, 300 mm long. | Job | 20.00 | 302.63 | 6,052.6 |
| 12 | Providing & fixing of Channel for mould rest ISMC 100 mm, 660 mm long including 04 nos ISA 50 x 50 x 90 side cleat. | Job | 200.00 | 433.72 | 86,744 |
| 13 | Providing & fixing of Bench shoe ISMC 100 with 100 x 10 mm MS plate to be welded, length 660 mm. | Job | 200.00 | 2,131.68 | 4,26,336 |
| 14 | Buffing of moulds. | Numbers | 400.00 | 140.99 | 56,396 |
| 15 | Providing & Fixing of Embossing Plate as per Drg. No-RT-4216 & 2466 Note: Size of Embossing Plate (i)Year Plate(120 *50) mm = 1 Nos (ii) RE Plate (50 * 50)mm = 0.42 Nos (iii) 1/8.5 60 KG, 1/12 60 KG, DS 60 KG (250*70) mm = 2.92 Nos (iv) Drg No. Plate (125*50) mm = 1.04 Nos | Numbers | 1600.00 | 88.62 | 1,41,792 |
| 16 | General Mechanical Maintenance & Repair of Production Machines Like Mixer, Batching p l a n t , Screw Conveyor, EOT Cranes, De- Moulding Hoist, Pulling Hoist, Hydraulic Pump, Compressor etc - including oiling, greasing, replacement of worn out parts and maintenance of structural steel components of the mechanical structures and machines. Carrying out different repairing activities welding, cutting, bending, straightening, grinding, drilling, bolting etc. with all equipments like welding machine, gas cutter with gas cylinders, cutter machine, grinder, chain pulley etc. with all consumables like gas, electrodes, grinding wheel, drill machine, cutting wheel etc. and deploy competent and efficient labour to carry out different type of repairs at CSP/SFG/ALD. | Shift | 1200.00 | 4,581.15 | 54,97,380 |
| 17 | Generation of steam for steam curing of casted PSC sleepers at CSP/SFG with the help of steam coal fired boiler including arrangement of steam coal Gr.B/Bio- Fuel(Agricultural Husk Briquettes) including maintenance & repair of Boiler at CSP/SFG/ALD as per special condition attached. Size of steam chambers are 13.00 M x 1.00 M x 5.00 M. | Shift | 1200.00 | 13,748.38 | 1,64,98,056 |
| 18 | General electrical maintenance & Repair of Mixer, Batching plant, Screw conveyor, EOT cranes, Demoulding Hoist, Pulling Hoist, Hydraulic Pump, Compressor etc. by deploying competent and efficient labour to carry out different type of repairs at CSP/SFG/ALD. | Shift | 1200.00 | 2,708.1 | 32,49,720 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TOPSHEET.pdf
ATTACHMENT
StandardTenderDocumentUPTOCS11_1.pdf Standard Tender Document UPTO CS 11
ATTACHMENT
SPECIALCONDITIONSContract_1.pdf
ATTACHMENT
StandardTenderDocumentUPTOCS11_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .