GE/BAS-62/2026-27 Special repair of building No P-65 at Madhopur under GE Basoli

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed.

M&L in repair of Steel rolling shutters ( 1.25 mm thick lathe) with ball bearing, including top cover, anchoring rod, hasp and staple, spring, hood, clamp, guide rail and including all other accesories whichsoever required to make the shutter functional and fixing in position as indicated, complete push pull or manual type including taking down the existing shutter,including one shop coat of red oxide primer and two coats of synthetic enamel paint complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed

S&F Powder coating (min thickness of powder coating 50 micron) aluminium frame for door, windows, ventilators with one or more rebates including joining cleat fixing etc complete all as specified and directed

S&F For Powder Coating aluminium single or double leaf door shutter in single or two panels with standered aluminium section weighting 0.55 kg/m including necessary jointing cleat, glazing clilps,rubber neoprene packing , handles 2 Nos in each door hinges, 02 nos of tower bolt 150mm, 01 nos of mortice lock three lever,01 nos of door stopper and hydraulic door closer in each shutter powder coated snap beading screws etc including 5mm thick tinted glass complete all as specified and directed

Material & Labour for Box type steel windows and ventilator comprised of tubular frame and shutters made out of 1.25 mm thick M S sheet tube, factory made with double side shutter wire gauged shutter using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions & glass glazed shutter with Float glass/(Frosted glass in case of bath/toilet) panes of nominal thickness 4 mm with side hung shutters with steel handle and steel peg stay dovetailed or welded including 2 Nos tower bolts 150 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/C-TD/27/13 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M& for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper including smoothing of plastered surface by applying a coat of wall care putty 1 mm thick and one coat of primer complete all as specified and directed.

M & L for Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying two coat of oil bound distemper on walls, pillars, cornices surface including making good uneven surface/holes and smoothening of surface with wall care putty 1mm thick coloured in same shade where ever required etc. complete all as specified and directed.

M&L for roof treatment to RCC roof slab in following procedure:(a) M&L for liquid waterproofing treatment to RCC roof slab including dismantling of existing water proofing treatment complete, cleaning of roof slab and making good all disturbed portions of any description in the following procedure. (b) Prepare the surface by cleaning with concrete surface grinder, wire brush and a high pressure water jet and allow to dry. All defects and repair cracks of old concrete by cutting "V" groove, corners and joints of drain pipes shall be repaired with epoxy mortar and installed with epoxy primer as per manufacturer's instructions. (c) Laying 10 mm thick rendering in cement mortar 1:3 mixed with approved liquid waterproofing compound (as per manufacturer's instructions) to receive treatment on roof complete. (d) Applying three coats of polymer waterproofing coating as per manufacturer's instructions to achieve a dry film thickness of 1.5 mm and elongation at break of free film of approx. 500% ± 50% and tensile strength at 14 days over complete. Complete in all respects as per manufacturer's specifications and under the direction of Engineer-in-Charge/Consultant. Note: (i) Minimum 6 hrs interval between two coats shall be maintained. (ii) All accessories involved during application shall be supplied by a single manufacturer as a part of system. Work to be carried out by authorized applicator as per manufacturer's instructions. (iii) Providing test with filling of water continuous 48 hours. If there is any leakage, the same shall be repaired by the contractor without any extra cost. The rate includes filling cracks in existing roof with epoxy cement mortar using suitable bonding agent before laying cement plaster.