GE/SMB/T-34/2020-21

Amount

Excavation in tranches in any type of soil n exc 1.5 m wide and n exc 1.5 m depth and getting out for foundation,path,drain,pipe line etc, complete all as specified and as directed..

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone as in foundation /sub base of floor, filling and mass concrete.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L of half brick work with sub class 'B' burnt bricks straight or curved on plan any radius bult in CM 1:4 complete all as spd & dir.

M&L for 40 mm thick DPC to horizontal or vertical surfaces including necessary form work in PCC 1:2:4 type B-0 using using 12.5mm graded stone agg with integral WPC @ 3 % of cement by weight. Note:- Integral WPC Shall be measured and paid separately.

Supply only integral WPC of approved quality.

M&L for rendering 20 mm thick in cement mortar 1:4 on brick work or concrete surfaces as in bearing plaster complete all as directed.

M&L for providing two layers of bituminised craft paper over bearing plaster.

Returning filling in including spreading levelling, watering and well ramming in layers n exc 25 cm in any type of soil.

Spreading and levelling in floor etc with excavated soil in layers n exc 25 cm thick and including watering and ramming complete.

Removing excavated materials n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point

Form work to sides and soffits of roof beam, lintels, cantilevers, overhangs etc for fair finished faces complete

M&L for formwork to soffits of suspended slabs, such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick [Horizontal or sloping] for fair finished faces complete

Form work to edges of concrete flats, roofs exc 5 cm wide and n exc 10 cm wide

Formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete, complete all as specified.

S&F TMT bars 6 to 8 mm dia as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire [annealed] not less than 0.9 mm dia or scruing with clips.

S&F TMT bars 10 mm dia & above as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire [annealed] not less than 0.9 mm dia or scruing with clips.

Same as per item 16 but 5 mm dia and over upto and including 10 mm dia as in stirrups spacers and binders.

M&L for RCC 1:1 1/2 : 3 type A1(Nominal mix) using 20 mm graded stone aggregate as in lintel upto 1.5 m clear span, bands cover slab and the like including necessary form work.

M&L for RCC 1:1 1/2 : 3 type A1 (Nominal mix) using 20 mm graded stone aggregate as in chajjas.

M&L for RCC 1:1 1/2 : 3 type A1(Nominal mix) using 20 mm graded stone as in slabs supported on walls and the like complete all as specified

M&L for rendering 15 mm thick on concrete surfacres in cement mortar 1:4 using integral WPC @ 3 % of cement by weight when concrete is green [ Integral water proofing shall be measured and paid separately]

M&L for rendering 10 mm thick on brick work/ concrete internal surfaces in cement mortar 1:6

M&L for rendering 15 mm thick on external faces of brick work or concrete surfaces in cement mortar 1:4 using integral WPC 3 % of cement content by weight (Note : Integral WPC shall be measured and paid seprately )

M&L for rendering 5mm thick on concrete surfaces of ceiling in cement mortar 1:4 all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone agrregate) as in floor finished complete all as specified & directed.

S&F Pressed steel frames 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

S & F Factory made 35mm thick, IInd class H.W.Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as spd & dir.

Providing and fixing factory made PVC internal UPVC (rigid) door frame of the size 50mm x 95mm with a wall thickness of 5mm, made out of extruded 5mm thick, PVC sheet of density 600kgs/cbm manufactured by an ISO-9000 certified company, mitre cut at two corners and joined with 4 nos of 150mm long brackets of 15mm x15mm M.S. square tube of 19 guage through out the frame .The door frame shall be fixed to the wall using 65/100mm long M.S. screws through the frame by using anchor fasteners.A minimum of 4 nos .of screw to be provided for each vertical member & minimum 2 nos. for horizontal members etc. complete as per manufactures specification and direction of Engr-in-charge.

S & F Supply and fixing Box type Steel fixed ventilator comprised of tubular frame, hold fast etc all as specified complete dovetailed or welded complete including 10 mm squre bar as in grill 100mm C/C incl a shop coat of red oxid paint complete all as specified.Steel windows/ ventilator for industrial buildings, fixed type, with glazing bars complete all as specified.

Supply and fixing Box type Steel windows comprised of tubular frame and shutter made out of 1.25mm thick MS sheet tube factory made with double side hing wire gauge shutter and glaze shutter, of size 79 mm x 39 mm 16 gauze rectangular tubular frame with side hung shutters with glazing bars 12X3 mm flat iron including box/pintol type hinges with steel handles and steel peg stays, hold fast etc all as shown on drg no CEPZ/TD-354/09 sheet 1/3 to 3/3 complete dovetailed or welded complete including 10 mm squre bar as in grill 100mm C/C incl a shop coat of red oxid paint complete all as specified.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, complete all as specified.

S&F 4 mm thick figured, pin head type glass ordinary quality and glazing with oil putty or wooden beading in square n exc 0.50 sq m in each pane.

S&F Butt hinges 100 mm medium weight stainless steel 304 G complete all as specified and directed

S&F aluminium anodised barrel tower bolts of extruded section and fixed 200 mm long (ISI Marked).

S & F Aluminium alloy, anodised, sliding door bolt 300 mm size with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised all as directed.

Supply only stainless steel wire cloth 0.36 mm nominal dia grade 304 of wire and average of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples,complete all as specified and directed

M&L Non skid coloured ceramic tiles 7 to 8mm thick, joint free (square/rectangular joint free) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortor 15mm thick in CM 1:6, complete all as spd & dir.

M&L glazed coloured ceramic tiles in vertical surfaces of wall of size 350x 250x 7mm/ 450X 350X 7mm/450X 300X 7mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4 on brick /concrete surfaces complete all as spd & dir.

S&F counter top wash hand basin oval type vitreous china white size 630 x 425 x 160mm excluding taps, waste chain and plug complete all as specified and directed at site (Make : Parryware / Hindware or equivalent as approved by GE

M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. complete all as spd & dir.

S&F looking mirror frame less, bevelled edge, fancy type area exc 0.50 Sqm but not exc 1.5 Sqm of 4 mm thick glass & mounted on 4 mm thick plywood complete all as specified and directed by GE. (Make of glass : Modi float / Saint globin / Triveni float glass)

S & F in repair PVC connection 15mm with PTMT nut of length 450 mm long complete.

S&F angle valve one way cast copper alloy, fancy type, chromium plated with cup (concealed type) (bore of pipe 15 mm) all as specified and directed.(Make;-Prayag cat no 8310, NMV / SOMA or equivalent as approved by GE

Cutting chases, on brick wall pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth for consealed water tubing etc and making good, disturbed surface to match.

S&F 15 mm bore tubes medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor.

S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete.

M&LPVC ( SWR ) floor trap for 75 mm bore pipe outlet , plain with grating including jointing with solvent cement complete all as specified and directed .

S&F PVC ( SWR ) bends ,75 mm bore of of any radious complete.

S&F 75 mm bore PVC ( SWR ) pipes single socketed , in any length laid in trenches or in floors complete .

S&F 110 mm bore PVC ( SWR ) pipes single socketed , in any length laid in trenches or in floors complete .

S&F bib taps for 15 mm bore pipe cast copper alloy with crutch or butterfly handle,screwed down, screwed for iron pipe and fixed (Make : NMV/ NMC or equivalent as approved by GE)

Supply only pillar taps cast copper alloy chromium plated ,screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts screwed for iron pipe (bore of pipe 15mm)

S&F 125 mm chromium plated shower rose with or without swivel joints any size incl. fixing to steel pipe or union

S & F 15 mm concealed type fancy type, chromium plated with long shank and cup stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F vitreous china wash down water closet (pedestal pattern) white (excluding fixing bolts, flushing cistern & flush pipe) including connection to outgoing drain & flushing pipe complete all as directed.(Make:-Parryware / Cera / Hindware)

S&F CP Jet fixed to WC (E) type including fancy type with PVC connections.

S& Fixing Vitreous china ,Squatting pan 'Orissa' pattern size 580x440mm white with integral foot rest including all joints and making good to the floor,etc complete all as specified. (Make:-Parryware / Cera / Hindware)

S & F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) incl urinal spreader complete all as specified.

S&F Rotational moulded polyethylene coloured water storage tanks (cylinderical vertical with closed top) hosted and fixed in position (1000 Litres capacity) all as specified & directed by EIC. ISI Marked

S&F PVC Ball valves, high pressure, with polythene float & Aluminium rod & fly nut complete, screwed for iron pipe or brass ferrule and fixed 20 mm bore pipe (Make : Prayag)

S&F Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm bore pipe.

Supply only PVC valveless, Dual flush syphonic action type, flushing cistern, ISI mark low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed

Supply only waste fittings brass chromium plated for glazed ware basin etc, 32 mm dia with long screwed shanks and flynuts, flange and bedded in red lead cement and other end fixed.

S&F CP brass tubular towel rail 20 mm dia D type, 60cm long including brackets all as directed by EIC

M&L for preparing of new previously untreated surfaces of wood or wood based material over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparing of new previously untreated surfaces of Steel and Iron surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparing new surfaces on wall plastered or unplastered surfaces and applying two coats of cement based paint

M&L for preparing surfaces, plastered or unplastered new surfaces of walls and applying three coats white wash all as specified and directed.

M&L for preparing New plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling all as specified and directed.

M&L for broken stone hard core of gauge not exc. 63 mm deposited spread and leveled in layers not exc 15 cm thick watered and rammed to a true surfaces all as specified and directed.

M&L for PCC 1:3:6 type C-2(using 20 mm graded cr. stone aggr), 75mm thick as in plinth protection finished even and smooth without using extra cement layed in bays not exc. 2.00m and joints filled with bitumen sand mastic with ratio (1:3 )complete all as spd & dir.

Filleting section not exc 25 Sqcm in any position and any shape in CM 1:3 including all miters stop etc.

M & L Cement concrete 1:2:4 type B1 in surface channels and drains

Providing, cement concrete type B-0 (1:2:4 using 12.5mm graded stone agg) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

M&L for rendering 15 mm thick on external faces of brick work or concrete surfaces in cement mortar 1:4

M & L cement mortar 1:2 Setting coat 3mm thick, trowelled to even and smooth finish

Supply and laying PVC (SWR) pipes 150 mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

M&L Construction of Septic tank of 25 users all as per DRG NO CEPZ/C-TD/13/13 Sheet 1/5 to 5/5 and as specified below :- Earth work in any type of soil, Hard core of stone, Brick work in CM (1:4), PCC (1:3:6) Type C-1 in base, RCC (1:1.5:3) Type A1 Nominal mix in RCC Members, Brick aggregate 80mm to 20 mm gradded, CI Pipe (sand cost) in Inlet, outlet etc, 20 mm plaster in CM (1:4) using approved water proofing compound finished even & smooth internally, flush pointing externally as work proceeds, removing surplus materials to a distence exc. 25.0 m but n.exc. 500 m, rest all as per Drg. (No other items of BOQ is applicable in this item)

M&L for Construction of Soakage well 1800 mm internal dia x 4500 mm deep all as per DRG NO CEPZ/C-TD/13/13 Sheet 1/5 to 5/5 and as specified below :- Earth work in any type of soil, Hard core of stone, Brick work in CM (1:4), PCC (1:3:6) Type C-1 in base, RCC (1:1.5:3) Type A1 Nominal mix in RCC Members, Brick aggregate 80mm to 20 mm gradded, Inlet pipe etc shall be of 150 mm dia SGSW pipe Grade 'A', 15 mm plaster in CM (1:6) finished even & fair internally, removing surplus materials to a distence exc. 25.0 m but n.exc. 500 m, rest all as per Drg. (No other items of BOQ is applicable in this item)

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil

Machine pressed precast concrete interlocking paver block any shape and size of 60 mm thickness, M-35 Grade with grey cement and pigment, over and incl 50mm thick sand cushion complete all as specified.

M & L for point wiring for one light/one fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) with in and including PVC concealed conduit having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet for switches and sockets , including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface area and white wash /colour wash to matching with the existing colour and all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)(Make of 1.5 sqmm copper wire:Grandlay,L&T and Finolex, PVC conduit Make: Finolex,Plaza/Bajaj).

S & F for switch piano flush type one way 5 amps SP complete all as specified and directed, make : Havells (REO) or technocommerically equivalent make of cona /SSK .

S & F for lamp holder/batton holder/angle holder insulated body(Metal ring) with back bakelite plate suitable for batten fittings, make : Havells (REO) or technocommerically equivalent make of cona /SSK .

M & L for ceiling rose 65 x 50mm three terminals complete all as specified and directed, make : Havells (REO) or technocommerically equivalent make of cona /SSK .

Supply and fixing sheet metal enclousre for DBs when MCB to be used double door powder coated factory made flush fixed complete with 200 amps rated bus bar 240 volts single phase 4 ways complete all as specified and directed,Make:Legrand or technocommerically equivalant make of ABB/Siemens.

MCB SP 6 to 32 amps 240 Volt 'B' series complete all as specified and as directed,Make:Legrand or technocommerically equivalant make of ABB/Siemens.

MCB SPN 6 to 32 amps 240 Volt 'B' series complete all as specified and as directed,Make:Legrand or technocommerically equivalant make of ABB/Siemens.

Supply and Fixing 1100 volts grade ,ISI marked ,heavy duty cable PVC insulated solid aluminium conductor , served with inner sheathing of PVC tape and overall PVC Sheathed in service connections 16 sqmm 2 core aluminium conductor suspension by GI wire 4 mm dia and insulated hanger not more than 1 Mtrs apart etc complete.Make:Havells/KEI/Grandlay

Supply only for LED ADORE Lamp, B22 type ,15 watt,make :Havells , cat part no: LHLDDEEEML8R015 or technocommercially equivalent of make : Wipro/Philips/Crompton .

M & L for LED tube light fitting 20 watt, 230 volt,box type complete bipin holders, connector block and retro LED rod of 20 watt polycarbonate diffuser having high efficacy (single side connection) complete with all accessories internally pre wired batten(single side connection) and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed,LED tube rod ,make :Havells ,cat part no: PHOTONULTRAE 2.01213T8SSTL18WLED865SPC and LED tube light batten ,make :Havells ,cat part no: REGALBATTENT 8UPTO1X22WSSBSWH or technocommerically equivalant make of Crompton/Philips/Halonix. Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 2 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost.

S & F of security lights lumanires ASTRA NEO LED streetlight made up of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP66 protection complete fitted on bldg with brackets made out of 32 mm dia GI pipe light grade 1.5 in length long with suitable size of 2 nos MS flat clamps FI 25 x 3 mm including nuts,bolts including connecting up with PVC copper conductor wire 1.5 sqmm s/c from security light to ceiling rose etc, complete all as specified and directed,make: Crompton,cat part no LSTS-25-CDL-M or equivalant make of Havells/Bajaj. Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 2 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost. (iv) Contractor shall arrange complete material at site for approval of GE before incorporation in the work.

Supply and fixing house service bracket (Hook type ) complete with 3.0 mtr long GI pipe 40 mm dia med grade two nos 90 degree bends ,MS hook and stay or guy complete all as specifed and directed.

M & L for providing/cutting the round /square hole on the wall and supply and fixing propeller type AC ventilating fans(Metalic body ) Single phase , 230 volts 300 mm sweep including grouting and fixing the ragged bolts in wall for exhaust fan and louver shutter on the exhaust side wall (outer surface of the wall ) and connecting PVC insulated three core 1.5 SQMM copper cable from ceiling rose to exhaust fan motor and writing MES No with black synthetic enemel paint 2.0 cm high complete all as specified.Make of Exhaust fan - Havells/Crompton/Bajaj.

M & L earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore medium grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt and precast PCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

M&L for Cutting existing GI/Cast iron water main pipe line 150 mm bore of pipe in position far making branch connection ( insertion of GI/Cast iron Tee) including excavation and earth work complete all as specified and as directed. Note- GI fittings such as tee, bends, elbow, reducer etc joint and jointing material for fixing of GI fittings shall be measured and paid separately.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor/drain, filling mass concrete etc, all as specified.

Demolition of plain cement concrete in ground floors or above ground floor and paving n.exc 15 cm thickness (Below or above ground level)

Demolition of brick work or stone masonry, built in cement mortar incl all quoins, arches pillars etc all as spd.

Cleaning sludge and mud etc. of any type & in any position as in drains with an average depth 30 cm and 30 to 45 Cm in width as in foul smell.

Demolition and breaking upto 300 mm drain pipes

M&L Reinforcement pipes 300 mm dia, class NP2, laid and jointed complete with collars.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for

Raking out joints/pointing to brick work in walls or to bricks on edges in floors, surface channels of cement morter etc.

Extra for forming fair finished drain or drain channel 30 cm inner girth in cement concrete using extra cement incl forms moulds, mitred stopped ends etc complete all as specified.

M&L of brick work for drain work with sub class 'B' burnt bricks laid on edges ,bedded, jointed in CM 1:6 and pointed in CM 1:3 complete all as spd & dir.

-ditto but except brick complete all as specified

M&L for flush pointing to brick massonry in CM 1:3 incl raking out joints/pointing to masonory work complete all as specified.

Precast cement concrete 1:2:4 type B1 (using 20 mm graded stone aggr) as in cover slabs (for drain & manholes etc) with plain faces, set in cement mortar 1:4 all as specified

M & L in Cement concrete with 1:3:6 type C-2 Concrete bed to drain pipes dia 300mm including packing under and completely surrounding pipes with concrete after they are laid and tested.

M & L in Cement concrete with 1:3:6 type C-2 Concrete bed to drain pipes dia 150mm including packing under and completely surrounding pipes with concrete after they are laid and tested.

M/S BAWA TRADING CO