Providing Cash Collection counter for Senior Citizens and Physically Challanged persons in the Cellar floor and Providing Chainlink fencing around Transformer plinth for 4nos 33/11 kV GIS SS (Kannamapet, Damodaran Street,Millers road,and Corporation

Amount

Dismantling brick/ stone masonry in cement mortar met with below ground level during execution including labour, tools etc.complete.

Earth work excavation for foundation in ordinary soil with lead of 10 to 100 m and lift of 3m in sand , silt or other loose soil,wet sand , or silt not under water,light black cotton soil, sandy loom and ordinary soil including excavated earth

Supplying and filling in foundation and basement with filling sand in layers not more than 15 cm thick well rammed and watered consolidated etc complete as per standard specification

Re filling in foundation with excavated earth in layers not more than 15 cm thick well rammed and watered consolidated etc complete as per standard specification

Providing and laying PCC 1:4:8 mix using 40mm HBG machine crushed metal for foundation concrete including cost of all labour,materials ,lead ,lift ,curing etc.complete

Laying PCC 1:2:4 mix using 20mm down graded HBG machine crushed metal for foundation concrete including form work , cost of all labour,materials ,lead ,lift ,curing etc.complete as per standard specification.

Brick work in CM 1:6 (one cement & Six sand) using Fly ash bricks of size 230*110*70mm including finishing ,curing etc.complete complying with standard specification - Super structure

Supplying and fixing MS angle, GI Chainlink Fencing, etc wherever required as directed by the Engineer as per standard specifcation

MS Angle

GI Chain link fencing 10G 2''x2" size tie with 18G GI Binding wire

Supplying and fixing MS grill gates ,MS grills, etc.at various levels as per approved drawing using channel, squar rods, ornamentel grill parts and flat including fixing in position with suitable hold fast locking arrangements etc.complete as per standard specification

Supplying and fabrication and fixing in position of anodised aluminium natural colour matt finish sliding window of size 1.18x1.48 m in two track in all floors with following sizes. All the two shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section of outer frames as shown below with necessary accessories such as rubber beading , handle,fixing 4mm thick clear sheet glass including all required for fabrication etc. complete. Necessary dimantling making holes in RCC columns , beams, masonry wherever necessary with power drill to the extent required and made good to the original condition after fixing as directed by the dept.Engineer. The Al. surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI 1868/1962 specification for an average anodic film thickness of not less than 15 microns. ( All materials should be got approved by the Executive Engineer) before fixing in position. Frame:-Bottom track 62x37 @1.218kg/m Side and top 62x31.5mm at 0.788 kg/m. Shutter section Bottom & top 40x18mm @ 0.38kg/m Plain side vertical 40x18mm @ 0.38kg/m. Inter locking vertical 40x18mm @ 0.632kg/m as directed by Engineer incharge.

Supplying fabricating and fixing in position of Aluminium Powder coated fixed type glazed partition with extruded aluminium fabricated grill ( bank grill) for cash collection counter (above the counter table) with 45cm height 6mm thick plain glass with suitable half round opening for cash counter , locking arrangements and 1.38m height extruded aluminium fabricated bank grill and top portion with 9mm thick Duratuff or equvalent both side prelaminated exterior grade MDF board including necessary Aluminium L angle, Clips, cost of all materials, powder coated aluminium sections, lead, lift, labour for fabrication fixing in position etc. complete as per direction of engineer at site.

Supplying, fabricating and fixing in position of Aluminium Powder coated matt finish door of size 1.00x2.10m half glazed and half MDF Both side PLB using 9mm thick PLB and 6mm thick glazed door using rectangular al.box section of following sizes (Top & Middle = 50x 44.45 x 2.5 mm @1.292 Kg/m Bottom =100x 44.45x 2.5 mm @ 1.974 Kg/m,Vedrtical style =50 x 44.45 x 2.5 mm @ 1.292 Kg/m) for frame and shutter with necessary such as rubber beading al.clips Best double action springs ,al.handle on both side ,floor stopper ,tower bolt,locks and glass including all labour , power consumption charges required for fabrication if necessary chipping ,dismantling ,making necessary holes in RCC columns ,beams,or masonry wherever necessary with power drill to the extent required and made good to the original condition after fixing complete. The al.surface must be Powder coated of approved colour with matt finish thickness of not less than 15 microns for all sections and as directed by the engineer at site.

Supplying & fixing CW doors of size 1.18x2.1mwith Kongu wood of outer frame of size 100x75 mm and door shutters Solid core flush shutters with teak ply on both side with teak wood lipping alround 35mm thick both sides pre laminated with necessary adhesive and CP screws complying with standard specification . The rate inclusive of three coats of best quality varnish but including cost of Suitable Hinges Aluminium furniture fittings such as 300 mm tower bolt 2 Nos. 200 mm tower bolt 1no. 300mm aldrop 1No.Aluminium arnamental handle 2 Nos.and 1No.door stoper etc.complete

Supplying and fixing in position of hydraulic door closer heavy duty using Aluminium Extruded section body tubular type universel with ISI mark double speed adjustment like Hardwin,Gazal or equvalent quality including cost of all material, lead, labour etc.complete.

Plastering with cm 1:5 mix using 12mm thick for inside and outside walls, plinth protection including cost of all materials,labour,lead, lift etc complete

Paving the floor with design vitrified floor tiles of Johnson(Morbonite),Nitco, Euro (quality, colour and shade as directed by the engineer at site) of size 600 mm x 600mmx 8mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement mortar neatly finished as per standard specification .

Colour washing two coats of approved Plastic Emulsion Paint over one coat of primer for inside wall including cost of all materials labour lead lift etc complete.

Painting new wood work with two coats of synthetic enamel paint of approved quality and colour over a priming coat including cost of all materials etc complete.

Painting new iron works with two coats synthetic enamel paint over one coat of primer including cost of all materials , lead,lift etc complete.

Providing computerised cash collection counter table desk arrangements of width 0.60m & height of 0.75 using 18mm thick water proof plywood with cash drawer of size 0.50x0.60x0.20m along with denomination racks with Lock & handle arrangements and necessary arrangements to install CPU UPS and battery compartments below the cash drawer, keyboard & printing paper tray with slot holes for paper moving,(all with 18 mm WP plywood) foot rest arrangements and the countersides extended to a length of 1.2m from the table and with hand rest arrangements of 0.6m equalies spaced on consumer side and counter side with counter separation at every 1.22m C/C & counter back closed using 19mm thick good quality commercial plywood for table top and CPU, UPS and battery arrangements Cash drawer,keyboard & Hand rest counterback and counter sides,separates arragements and all outer edges finished with teak wood lipping.The top of the table. hand rest top and key board top portion drawer front face,counter back side and counter sides nearer to the door should be finished with 1mm thicksunmica and all other faces should be painting with 2 coats of enamel paint over one coat of primer. Rates includes cost of all materials leads,lifts etc.,complete.

Supplying and providing heavy duty MS powder coated perforated three seated chairs using corrosion resistant pipe of 50mm dia for supports and 20mm dia for seat and back and 18gauge thickness corrosion resistant perforated sheet for seat and back confined with hand rest for each collection counter including cost of all materials , lead, lift, labour etc. complete as directed by the engineer at site. ( 1set consist of 3 chairs)

PREMKUMAR