ADDN/ ALTN OF JCOs MESS BLDG NO P 885 AT 33 CSR AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN OF GE SUKN

Amount

BOQ Part-I (B/R Work)

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out, returning, filling and ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm watering and removing surplus soil to a distance not exc. 50 m and making good surface as in hard / dense soil complete all as specified and directed.

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M & L for plain cement concrete, 1:4:8, Type D-2, (using 40 mm graded stone aggregate) as in foundation, base, hardstanding, etc concrete complete all as specified and directed.

M & L for plain cement concrete, 1:4:8, Type D-2, Nominal Mix (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for plain cement concrete 1:2:4, Type B-2, Nominal Mix (using 40 mm graded stone aggregate) as in surface channel or drain or benching in manhole complete all as specified and directed.

M & L for providing reinforced cement concrete A1 (1:1.5:3) Nominal Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete A1 (1:1.5:3) Nominal Mix using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete A1 (1:1.5:3) Nominal Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete A1 (1:1.5:3) Nominal Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posps and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25, Design Mix using 20 mm graded stone aggregate as in Chajjas and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25, Design Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m sapn and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc. complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for applying evenly a coat of blown type bitumen @ 1.50 Kg per Sqm including cleaning of surface and binding with clean dry sand @ 0.05 cum per Sqm including 50 micron Polythene film thick laid on a coat of bitumen primer @ 0.40 kg per Sqm complete all as specified & directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in square,rectangular orpolygonal , rough finished surface of concrete complete all as specified and directed.

S & F of 35 mm thick flush shutter solid core construction, with MDF board core and plywood face panels, commercial type on both faces complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each complete all as specified and directed.

S & F of 125 mm long (Length of bolt) Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

S & F of 100 mm long Aluminium butt hinges, complete all as specified and directed.

S & F of 150 mm long Aluminium handles, cast type, anodised complete all as specified and directed.

S & F of 100 mm long Mortice lock, 4 lever, aluminium body, vertical type, complete all as specified and directed.

S & F of 150 mm size (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S & F of Door closer Aluminium(Die cast) body Hydraulically regulated ( designation No. 3) universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 t0 80 kg complete all as specified and directed.

S & F of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks of galvanised wire staples complete all as specified and directed.

S&F decorative polished wooden brackets / supports to be fixed at walls for holding curtain rods and corners to be fixed at ends of curtain rod of 20mm dia with necessary screws complete all as specified and directed. Note :- 2 Nos bracket and 2 Nos corners shall be measure as one pair

S&F 28 mm dia curtain rod, mild steel, chromium plated wooden finish complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

S & F of mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexagonal or square nut, exc. 22.5 cm and not exc. 30 cm long and 16 to 20 mm dia of shank complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per Sl item No. 1.42 above but 8 mm dia in stirrups, spacers and binders.

M & L for mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F of rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe – 410 – W(Gde E - 250) quality 'B' complete all as specified and directed.

All as per Sl item No. 1.45 above but with riveted, bolted or welded attachment.

S & F framed work as in designer doors or gates having circular geometry formal work as in doors or gate mades of hollow square pipe or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing confirming to Fe – 410 – W (Gde E - 250) quality 'A' complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S & F of steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F of steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed. Make:- AVA Steel Industries / M/s AGEW Steel manufacturers Pvt Ltd / M/s Ajanta Ispat Pvt Ltd Siliguri

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc., complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed. Make:- Colour Roof (India) Ltd / TATA Bluescope Steel Ltd / Dyna Roof / Bhushan Power & Steel Ltd / Prestar Infrastructure Projects Ltd.

All as per Sl item No. 1.53 above but plain steel sheet.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) 15 mm thick screed bed in CM 1:4 on surface. (ii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (iii) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Contd...)

(iv) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction. (d) APP based polymeric membrane shall be manufactured by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (e) Water proofing aluminium paint shall be by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited

S&F pre painted 4 mm thick E-board designer/ decorative ceiling of size 600x600mm fixed or laid / inserted to aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including anodised aluminium snap grid frame work for false ceiling hanging from structural steel / scantling with 6 mm GI wire (upo 1200mm length)adjusting level fixed to roof slab by means of ceiling cleats made out of GO flat 40x3 mm size 600 mm long and expansion hold fastners 12.50 mm dia 40 mm long with and including building board complete all as specified and directed. Make of boards:- Everest / Visaka Industries / Lafarge / Armstrong Make of aluminium snap grid:- M/s Saint-Gobain Gyproc India Pvt Ltd / M/s USG Boral Building Products (India) Pvt Ltd / M/s PR Ceiling Products

M & L for granite (of any type) tiles 18-20mm as in platform thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with nosing over 15mm screed bed in CM 1:4 complete all as specified and directed.

M&L 16-18 mm thick granite (of any type) tiles machine cut, bedded over & including 15 mm thick screed bed in CM 1:4, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing complete all as specified and directed.

M&L providing precast cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) in window or door cills, lintels upto 1.5m clear span, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match including necessary formwork or moulds etc. complete all as specified and as directed.

M & L for providing 75 mm thick cement concrete 1:2:4, type B-2, Nominal Mix (using 40 mm grade stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

M & L for providing 75 mm thick cement concrete (1:3:6) type C-2(using 40 mm grade stone aggregate) as in plinth protection complete all as specified and directed.

M & L for providing 100 mm thick cement concrete (1:4:8) type D-2 (using 40 mm grade stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

M & L for providing 75 mm thick cement concrete (1:4:8) Nominal Mix type D-2 (using 40 mm grade stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

M & L for providing 40 mm thick cement concrete (1:2:4) type B-0 (using 12.50 mm thick graded stone aggregate) as in floor as underlayer to recieve cement screedtop surface even and fair complete all as specified and directed.

All as per item No. 1.65 but type B-1 (using 20mm graded stone aggregate) as in floor including finishing the surface even and smooth using extra cement complete all as specified and directed.

M & L for providing 25 mm thick cement concrete (1:2:4) type B-0 (using 12.50 mm thick graded stone aggregate) as in floor, laid in panels and position to conform to design and finishing top surface even and smooth with using extra cement complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick as in floors, set and jointed over and including 15 mm thick screed bed in CM 1:4 and pointed in grey cement and pigments to match the colour of tile including dismantling complete all as specified and directed. Make : Lovely / Anjali / Ultra / Bansal / Nitco / Multiwyn

M&L coloured glazed ceramic tiles 300 x 450 x 7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 complete all as specified and directed. Make :- M/s Asian Granito India Ltd. / M/s Somany Ceramics Limited / M/s Varmora Granito Pvt Ltd / M/s OASIS Vitrified Pvt Ltd / M/s Sunshine Tiles Co (P) Ltd (Tiles) /Orient Bell Ltd / H & R Johnson India Ltd

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed. Make:- M/s Asian Granito India Ltd. / M/s Somany Ceramics Limited / M/s Varmora Granito Pvt Ltd / M/s OASIS Vitrified Pvt Ltd / M/s Sunshine Tiles Co (P) Ltd (Tiles) / Orient Bell Ltd / H & R Johnson India Ltd

M&L 10 mm thick vitrified ceramic tiles light shade (square / rectangular) polished, area of each tiles exc. 0.42 but n.exc 1 Sqm sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 and dismantling complete all as specified and directed. Make :- M/s Asian Granito India Ltd. / M/s Somany Ceramics Limited / M/s Varmora Granito Pvt Ltd / M/s OASIS Vitrified Pvt Ltd / M/s Sunshine Tiles Co (P) Ltd (Tiles) / Orient Bell Ltd / H & R Johnson India Ltd

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing the surface even and fair complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces and finishing the surface even and fair complete all as specified and directed.

M & L for 10 mm thick rendering in cement mortar 1:3 on other than fair faces of brick work or concrete surfaces and finishing the surface even and fair complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finishing the surface even and fair mixed with water proofing compound complete all as specified and directed. ( Note WPC shall be measured and paid seperately).

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of Oil emulsion distemper over a coat of cement primer over a thin layer of wall care putty complete all as specified and directed.

M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint complete all as specified and directed.

M & L for preparation of newly plastered or previously untreated surfaces of ceiling and applying two coats of Oil emulsion distemper over a coat of cement primer over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of exterior weather coat paint over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed. Make from serial No. 1.87 to 1.91 shall be of -Royal acrylic (crimson paints pvt ltd) / Dulax / shalimar paints ltd (Extra maximum ultra) / Berger paints ltd (weather coat) / Asian paints ltd (Appex ultima) / Jotun India pvt ltd

S & F of 3 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

All as per Sl item No. 1.81 above but 4 mm thick sheet glass

All as per Sl item No. 1.81 above but 4 mm thick sheet glass but exc 0.50 sqm in each pane

S&F 4.8 mm thick tinted/dark film glass and glazing with oil putty / wooden beads in square exc 0.50 sqm in each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

M & L for preparation of New or previously un-treated steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S & F 15 mm bore galvanised steel water tubing medium grade with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S & F 20 mm bore galvanised steel water tubing medium grade with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S&F rotational moulded polyethylene three layered water storage tanks of 1000 Litres capacity, multilayered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed. Make of tank:- Sintex / Polycon / Oriplast / Jindal Make of ball valve:- Prayag Cat No. 152 or equivalent in M/s Pearl Precision Products Pvt Ltd / Polytuf

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed. Make :- Jotun India Pvt Ltd / Apcolite (Asian) / Luxol (Berger) / Jenson & Nicholson Paints Ltd (Borolac) / Shalimar Paints Ltd (Superlac)

S & F of 15 mm bore bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F of 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'HOT' or 'COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F of 15 mm bore stop valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F of 15 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 142 gram) complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls, floor complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls, floor complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) Vent cowl complete all as specified and directed

S & F of 75 mm bore PVC (SWR) Vent cowl complete all as specified and directed

S & F of 75 mm dia PVC (SWR) Plain floor trap, with grating including jointing with solvent cement complete all as specified and directed.

M & L for cement concrete 1:4:8, type D-2, Nominal Mix, using 40 mm graded stone aggregate as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested including dismantling old pipes complete all as specified and directed.

M & L for 150 mm bore salt glazed stoneware (SGSW) drain pipes grade 'A' laid in trenches and jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed.

M & L for cutting into existing manholes for connecting new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm dia pipe complete all as specified and directed.

S&F in repair CP fancy type soap dish holder of dia not less than 110mm, with wall flange complete all as specified and as directed. Make:- Jaquar, Cat No. - ACN-1131N or equivalent in Hindware (QUEO & Italian Collection) / Prayag (D’OR Series) / Cera (Premium / Luxury Range)

S & F for brass chromium plated shower rose 125 mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S & F of 75 mm dia stainless steel grating complete all as specified and directed.

S&F towel rail, 18 mm (minimum) dia & 600 mm long of stainless steel chromium plated, fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed. Make:- M/s Jaquar & Company Pvt Ltd (Essco), Cat No. - AEC-1111N or equivalent in Hindware (Less Italian Collection) / Cera (Med Range) / Prayag (7000 & 8000 Series)

S&F in repairs corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, 300mm side with brass chromium plate bracket guard complete all as specified and directed. Make:- Prayag, Cat No. - BEA-44 or equivalent in M/s Jaquar & Company Pvt Ltd (Essco) / Hindware (Less Italian Collection) / Cera (Med Range)

S&F in repairs angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed. Make:- M/s Jaquar & Company Pvt Ltd (Essco), Cat No.- SQT-526NKN or equivalent in Hindware (Less Italian Collection) / Cera (Med Range) / Prayag (7000 & 8000 Series)

S&F in repairs health faucet 15 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook complete all as specified and directed. Make:- M/s Jaquar & Company Pvt Ltd (Essco), Cat No. - ALE-ESS-585 or equivalent in Hindware (Less Italian Collection) / Cera (Med Range) / Prayag (7000 & 8000 Series) Make:- Jaquar, Cat No. - ALD-565 or equivalent in Hindware (QUEO & Italian Collection) / Prayag (D’OR Series) / Cera (Premium / Luxury Range)

S&F vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed. Make of wash hand basin:- Hindware, Cat No. - 10010 (Starwhite) or equivalent in Cera (Med Range) / M/s Jaquar & Company Pvt Ltd (Essco) Make of waste fitting - Prayag Cat No.- BEA-10 or equivalent in M/s Jaquar & Company Pvt Ltd (Essco) / Hindware (Less Italian Collection ) / Cera (Med Range) Make of PVC waste pipe - Prayag / M/s Pearl Precision Products Pvt Ltd / Polytuf

S&F vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed. Make of Water Closet:- Hindware, Cat No. - 20011 (Starwhite) or equivalent in Cera (Med Range) / Essco Make of Seat cover:- Hindware, Model - Seat Cover Standard (Starwhite) or equivalent in Cera (Med Range) / Essco

S&F PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed. Make:- Parryware, Cat No.- E8055 or equivalent in Cera(1st quality) / Hindware / Essco

S&F vitreous china urinal half stall type, of size not less than 380 x 400 x 590 mm, white including chromium plated urinal spreader & waste coupling complete all as specified and directed. Make:- Parryware, Cat No. - C0583* (Combo set) (white) or equivalent in Cera (1st quality) / Hindware / Essco

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

Demolition of Re-inforced Cement Concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

S&F 10 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof and complete all as specified and directed. Make of GI Grid- M/s Saint-Gobain Gyproc India Pvt Ltd / M/s USG Boral Building Products (India) Pvt Ltd / M/s PR Ceiling Products Make of PVC Insulation Panel :- Rajshri Plastiwood Ltd / M/S Polyline Extrusion Pvt Ltd / M/s Navratan Specially Chemicals Ltd

M&L decorative type plaster of paris work of size not less than 50 mm x 50 mm, as in cornice or junction of wall and ceiling complete all as specified and directed.

S&F pre-painted powder coated aluminium anodised door, window, cup board and ventilator shutter and frame any type (sliding or openable) with frame and either similar work, fabricated aluminium mest etc, aluminium heavy section fabricated including all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw including cost of rubber gasket, beading roller wheels etc,complete all as specified and directed. Make:- M/s Halco Aluminium Extrusion / M/s Bhagwati Sai Metal Alloys / M/s Argent Industries Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate

Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e; at, top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P brass/ Stainless steel screws all complete as per architectural drawings and directions of engineer-in- charge. Make:- M/s Halco Aluminium Extrusion / M/s Bhagwati Sai Metal Alloys / M/s Argent Industries

S&F 12 mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination and other side balancing white laminated fixed with screw to timber / aluminium frame work complete all as specified and directed. Make:- Kitply / Bhutan Board / Novapan / Greenply

M&L 10 mm thick double charged vitrified ceramic tiles light shade (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20 mm thick screed bed in CM 1:6 finished even and rough complete all as specified and directed. Make :- M/s Asian Granito India Ltd. / M/s Somany Ceramics Limited / M/s Varmora Granito Pvt Ltd / M/s OASIS Vitrified Pvt Ltd / M/s Sunshine Tiles Co (P) Ltd (Tiles) / Orient Bell Ltd / H & R Johnson India Ltd

All as per Sl item No 2.23 above but in skirting / dado etc. laid over and including screed bed 10 mm thick in CM 1:3.

S&F 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. Make:- Kirloskar / Leader / Zoloto / Venus / Audco / Upadhyaya

Supply & fix GI Tee 25/20mm complet all as specified and directed

S&F15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

BOQ Part-II (E/M Work)

Taking down copper / aluminium concealed point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody or for taking credit, cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down copper / aluminium concealed sub main wiring complete with all fixture and fittings including cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down old unseviceable DB/TPN DB including MCB/ RCB / Isolator any size and any capacity complete all as specified and as directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch and including cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Make of cable:- Havells /MESCAB/ Polycab /Phinolex Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

All as per Sl. item No. 3.04 above but for one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 3.04 above but for one 5 / 6 Amps socket outlet point on independent board.

M&L point wiring with 2.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 2.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for 15 / 16 Amps socket outlet on independent board and including cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Make of cable:- Havells / KEI / Polycab / RR Kabel Ltd. / HPL Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

M & L concealed sub main wiring with 2 runs of 4 sqmm main wire along with 1 run of 4 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. Make of cable:- Havells / KEI / Polycab / RR Kabel Ltd. / HPL Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

All as per item No. 3.08 above but with 2 runs of 6.0 Sqmm main wire along with 1 run of 6.0 Sqmm earth wire.

S&F switch piano flush type one way, 5 / 6 Amps, 240 volt complete all as specified and directed. Make :- L&T / ABB / Legrand / C&S

S&F switch socket combination 3 pin 15 Amp, flush type universal complete all as specified and directed. Make :- Havells / Anchor / Legrand /C&S

S&F switch socket combination 3 pin 5 Amp, flush type universal complete all as specified and directed. Make :- Havells / Anchor / Legrand /C&S

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed. Make:- L&T / ABB / Legrand / C&S

S&F MCB SPN 40 to 63 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed. Make :- L&T / ABB / Legrand / C&S

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed. Make :- L&T / ABB / Legrand / C&S

S&F stepped type electronic fan regulator two module, with 5 step, AC 50 Hz 240 Volts grade complete all as specified and directed. Make :- Anchor / Legrand/ C&S

S&F ceiling fan 1200 mm (minimum) sweep, BEE 2 star (minimum) rated AC single phase 230 V, 340 RPM (minimum), squirrel cage induction motor with copper winding suspended from fan hook and including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 0.75 Sqmm copper conductor from ceiling rose to ceiling fan complete all as specified and directed. Make :- Orient / Ram Ratna Electricals Ltd (RRE)/ Cromptom

S&F in repairs exhaust fan 200 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvers, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint complete all as specified and as directed. Make :- Orient / Ram Ratna Electricals Ltd (RRE)/ Cromptom

S&F MCB DB, SPN 8 way, IP-43, IK 09, double door type with metal door, with 200A copper neutral and earth bus bar for fixing MCB, fixing flush to wall & making good the disturbed surfaces complete all as specified and as directed. Make :- L&T / Panasonic / Hager / ABB / Legrand / Indo Asian (Optipro)

S&F 12 watt LED bulb, inverter (backup) type, A19 shape with B22 base 230 Volts, battery with minimum 4 hrs backup time, frosted diffuser, suitable for surface mounting, total system lumen 900 Lm (minimum) on supply and 400 Lm (minimum) on battery, colour temperature 6500K (minimum), CRI 80 (minimum) complete all as specified and directed. Make:- Crompton / Century Led /C&S

S&F 09 watt LED bulbcomplete all as specified and directed.Make:- Crompton / Century Led /C&S

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings including taking down complete all as specified and as directed.Make :- Anchor / Legrand/ C&S

M&L earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick buried directly in ground in vertical position (earth pit not less than 2.25 m deep below the normal ground level) with top edge of the earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire of 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel, all as shown in electrical plate No. 3 connected to earthing test point and including dismantling complete all as specified and directed. Note:- The unit rate shall also include for earth work in any type of soil, PCC 1:3:6 type C1 chamber, RCC 1:1.5:3, type A1 cover slab, 50 mm thick reinforced with 8 mm dia TMT bar @ 140 mm C/C both ways, 10 mm dia plain bar lifting handle embedded in cover slab, 20 mm bore medium grade GI watering pipe, 15 mm bore GI light grade earth lead protection pipe, funnel, wire mesh, copper lugs, charcoal and common salt in alternate layer etc.

S&F sheet metal enclosures with socket single pole and neautral enclosure with a two pin and earth plug and socket complete with one single pole MCB's of 10 Amp complete all as specified and directed.

S&F LED light fitting 1 x 10 watt, 220V, AC PVC box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size for ceiling rose complete all as specified & directed. Make:- Crompton / Havells / Century LED ltd

S&F LED light fitting 1 x 20 watt, 220V, AC PVC box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size for ceiling rose complete all as specified & directed. Make:- Crompton / Havells / Century LED ltd

S&F 1 x 34 / 36 watt, LED Panel light fitting, square shape (2ft x 2ft), suitable for recess mounting in ceiling, integrated type, aluminium Housing, with high efficiency opal diffuser & integrated electronic driver etc., all electrical accessories pre-wired upto terminal block including all fixing accessories, electrically connecting complete all as specified & directed. Make :- C&S / Indiabulls LED / Crompton / Surya / Orient Electric Ltd. / HPL / Jaquar & Company Pvt Ltd / Eveready Industries India Ltd. / Havells

M&L earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20 x 3.15 mm copper strip complete all as specified and directed.

M&L air termination, single pointed, copper rod 12 mm dia and 300 mm long with all necessary nuts, washers bolts etc. complete all as specified and directed.

M&L test point terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25 mm drilled and screwed including 3 nos. 8 mm dia 25 mm long hex. head screw complete all as specified and directed.

S&F synthetic PVC insulator sutable for fixing copper strip upto 50 x 6 mm to wall / roof including necessary nut, bolts, washers etc. complete all as specified and as directed.

M&L earthing complete with copper earth plate electrode of size 600 x 600 x 3.15 mm thick buried directly in ground in vertical position (earth pit not less than 2.25 m deep below the normal ground level) with top edge of the earth plate not less than 1.5 m below normal ground level, connected to copper earth lead of size 20x3 mm by means of bolts, nuts, check nuts and washers of copper, all as shown in electrical plate No. 3 connected to earthing test point and including dismantling complete all as specified and directed. Note:- The unit rate shall also include for earth work in any type of soil, PCC 1:3:6 type C1 chamber, RCC 1:1.5:3, type A1 cover slab, 50 mm thick reinforced with 8 mm dia TMT bar @ 140 mm C/C both ways, 10 mm dia plain bar lifting handle embedded in cover slab, 20 mm bore medium grade GI watering pipe, 15 mm bore GI light grade earth lead protection pipe, funnel, wire mesh, copper lugs, charcoal and common salt in alternate layer etc.

MS ORIENT ENGINEERING WORKS

M/s TALCO

G C DUTTA N CO

KARMIBRINDA

MS ESSCON

GEETA CONSTRUCTION

M/S RANEN PAL