Repair and Renovation work at Circuit House at Ramgarh.

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item - A0 and disposal of excavated earth as obtained to a distance upto 50M including all lifts levelling, ramming the foundation trenches, removing roots of trees, shurbs all complete as per approved design, building specification and direction of E/I.

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume)

Providing coarse clean Sand in Filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing designation 75B brick work in C.M. (1:6) in foundation and plinth approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, costs of screening, materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125mm thick reinforced designation 75A brick work in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:2:4(1 cement : 2 coarse sand (zone-III) :4 graded stone aggregate 40mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, fotting, bases of columns, etc. for mass concrete

Lintels, beams, Plinth beams, girders, bressumers and cantilevers

Supplying, fitting & fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneeres of standard makew with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing Toe steel reinforcement of 8mm dia rods as approved design and drawing including carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL, TATA Steel, JSPL, Electro Steel Ltd. and Vizal Steel)

Providing designation 75B brick flat soling filled with local sand including cost of watering taxes royalty all complete as per building specification and Direction of E/I

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 2 coats of Plastic Emulsion Paint of Approved Shade and make over old surfaces as per building specifications and directions of E/I

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l.

Dismantling R.C.C.work including stacking serviceable materials in countable stacks within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l.

Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l.

Dsimantling old plaster and pointing in cement or lime and raking out joints to 15mm depth watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down old door and window shutters including stacking serviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhats in doors including stacking serviceable materials with all leads all complete as per direction of E/I.

Providing 250mm wide brick drain in cement mortar (1:6) with as. 150mm clear depth and 250mm apron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Water proofing for old and New Roof Slab : - Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with following steps:-

Surface preparation :- Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint/coating and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika India Pvt. Ltd/MYK schomberg/Dr. Fixit/fosroc or equivalent. Proiding and reparing of all corners and joints such as those between the parapet wall and the roof slab etc. shall be chamfered with 150mm x 150mm fillet of mortar (Cement sna - 1:4) admixed with acrylic polymer of Sika/Fosroc/MYK Schomberg/Dr. Fixit or equivalent.

Before chamfering surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.

1st coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600mm by brush or roller. After 1st coat of application, 45 gsm of fibre glass cloth to lay when the first layer is still green, 1st coat should be applied @ 1.50 kg/sqm/coat. For the purpose of measurement the entire treated surface will be measured.

2nd Coat :- To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface. 2nd coat should be applied @ 0.7 kg/Sqmt/coat. For the purpose of measurement the entire treated surface will be measured. After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be doen as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing coating to be protected from damage before screed over it. Water proofing Brand-Sika Topseal 109hi/Fosroc Brushbond RFX/Dr Fixit Pidifin 2K/MYK Auafin TG, Product Performance - chemical

Base part A : Acrylic copolymer, Part B : Specially graded cementtitious powder - Density 1.6 kg/l (mixed density) at +270C Tensile strength ~ 2N/mm2 after 28 days (with Fibre cloth) (according to ASTM D 2370) Pullout Bond Strength ~ 2 N/mm2 (concrete failure) (According to ISO 4624) Slant-shear bond strength~4 N/mm2 (According to FIP 5.15) Elongation at Break ~ 35% without Fibre Cloth and 20% with fibre cloth (According to ASTM D 2370)

Protection of treatedsurface with PCC : - The treated surface should be covered with 25mm/50mm PCC of M-20 grade (1:1.:3) with proper slope (1:120) towards the rain outlets in alternatepanels of 2 Mt x 2mt keeping 6mm gap between the panel joint intergal water proofing admixture conforming to IS 2645 @ of 100 ml per bag of cement to be added in the acreed concrete (paid separately for this items) all corners shall be chamfered with 150mm x 150mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between PVC pipe outlet and concerte surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insentive epoxy putty of Sika India pvt Ltd/MYK Schomberg/Dr. Fixit/Fosroc. For the purpose of measurement the entire treated surface will be measured."

Groove of PCC surface should be filled with Polysulphide Sealant. (Paid Separately) Brand - Sika India Pvt. Ltd./MYK Schomberg/Dr. Fixit/Fosroc. Warantly for five years.

Covering of treated surface with PCC : Providing 25 mm thick cement concrete M-20 (1:1.5:3) maintaining slope in alternate 2mt x 2 mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering and mixing cement concrete in mixer with admixture of integral water proffing and placing in position, skirting curing, taxes and royalty all complete as per building specification and direction of E/I. Panels that has been left should be casted next day. there should be 6mm gap between Panels Brand-Sika-Plastocrate plus, MYK proof WP 10, Fosroc-Conplast X421 ic Dr. Fixit Pidiproof LW+

Providing 19mm thick water proof cement plaster (1:3) with clean coasre sand of F.M. 1.5 with integral water proofing compound Liquid @ 125ml per bag cement including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. Brand-Sika-Plastocrate plus, MYK proof WP 10, Fosroc-Conplast X4211C, Dr. Fixit Pidiproof LW+ or Equivalent

Providing and filling of 6mm thick Groove between 50mm PCC Panels with Polysulphide Sealant (Poring Grade) as per drawings and technical specifications and direction of E/I. (with 18% GST) Brand - Sika-Polysulphide, Forsoc-thioflex 600, Dr. Fixit Pidiseal PS (42P, MYK Seal PS or Equivalent.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominalsize) over 75mm thick bed of dry brick ballast 40 mm nominal size,well rammed and consolidated and grouted with fine sand, includingnecessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade - Area of slababove to 0.50 sqm

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture

Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black ofany size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shadecomplete.

Extra for providing ISI marked Stainless Steel butt hinges instead ofM.S. pressed butt hinges bright finished of required size with necessaryscrews. (Shutter area to be measured).

Extra for providing lipping with 2nd class teak wood battens 25 mmminimum depth on all edges of flush door shutters (over all area of doorshutter to be measured).

Providing and fixing bright finished brass night latch of approved qualityincluding necessary screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass hanging type floor door stopperwith necessary screws, etc. complete.

Providing and fixing aluminium die cast body tubular type universalhydraulic door closer (having brand logo with ISI, IS : 3564, embossedon the body, door weight upto 35 kg and door width upto 700 mm), withnecessary accessories and screws etc. complete.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof S.Swire mesh (Two nos. glazed & one no. wire mesh panels)made of (big series) frame 116 x 45 mm & sash 46 x 62 mmboth having wall thickness of 2.3 ± 0.2 mm and single glazingbead / double glazing bead of appropriate dimension. (Areaof window above 1.75 sqm).

Providing and fixing stainless steel ( Grade 304) railing made of Hollowtubes, channels, plates etc., including welding, grinding, buffing, polishingand making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete, i/c fixing the railingwith necessary accessories & stainless steel dash fasteners , stainlesssteel bolts etc., of required size, on the top of the floor or the side ofwaist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel membersshall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wireand 1.4 mm aperture on both sides

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Anti skid/ Matt finish 600x600

Providing and fixing Glass mossaic tiles on finished plain wall surface ofsize 20 mm x 20 mm x 4 mm in all colour, design , fixing in customizedesign as per direction of Engineer-in- Charge. The glass mosaic tilesto be fixed on the wall surface with the help of approved adhesive appliedat the rate of 2.5 kg per sqm and grouting of the same. The rate isinclusive of all operation, material and required pattern approved byEngineer-in-Charge:

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm

thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistantboard

Providing and applying plaster of paris putty of 2 mm thickness overplastered surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm)

French spirit polishing Two or more coats on new works including a coat ofwood filler

Removing white or colour wash by scrapping and sand papering andpreparing the surface smooth including necessary repairs to scratchesetc. complete

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight notless than 10 kg/ sqm)

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Powder coated minimum thickness 50 micron aluminiumtubular handle bar

Providing and fixing 12 mm thick frameless toughened glass doorshutter of approved brand and manufacture, including providing andfixing top & bottom pivot & double action hydraulic floor springtype fixing arrangement and making necessary holes etc. for fixingrequired door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of alljoints, corners, junctions of pipes and masonry with polymer mixedslurry.

Providing & Applying high quality acrylic modified resin based textureof Dholpur/Red sand stone Pattern with anti algae and UV resistanceproperties to be applied as intermediate finish in desired pattern @43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrappingand properly cleaning the surface to remove loose particles from theplaster surface, followed by top coating with Premium Acrylic Smoothexterior paint with Silicone additives of required shade by twoor more coats @ 1.43 litres/10 sqm, complete as the direction ofEngineer -in-Charge.

Providing and supplying aluminium extruded tubular and otheraluminium sections as per the architectural drawings and approvedshop drawings , the aluminium quality as per grade 6063 T5 or T6 asper BS 1474,including super durable powder coating of 60-80 micronsconforming to AAMA 2604 of required colour and shade as approvedby the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extrudedaluminium frame work. Nothing extra shall be paid on this account).The weight of aluminium extruded section shall be taken forpurpose of payment.

Providing and fixing factory made single extruded WPC {Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal

strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2 modulus of elasticity 900 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).

Note: For WPC solid door/window frames, minus Smm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In­ Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC(Computer numeric control) routed of approved design by Engineer- in -charge which are machine cut for duct/shaft covering, partitionsand facades comprising of virgin polymer of K value 58-60(Suspension Grade), calcium corbonate and natural fibers (woodpowder/ rice husk/wheat husk) and non toxic additives(maximumtoxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimumcompressive strength 50 N/mm2, modulus of elasticity 850 N/mm2and resistance to spread of flame of Class A category with propertiesof being termite/borer proof, water/moisture proof and fire retardantand fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mmsquare hollow box section including applying a priming coat ofapproved steel primer, placed at grid made at 1.0 x 1.0 m or as perrequirement at site with necessary stainless steel fasteners and SSscrews etc., all complete as per direction of Engineer-In- Charge.(Note: M.S (mild steel) framework with priming coat and necessarySS fasteners and SS screws shall be paid separately.

Providing and fixing Ply wood 5 ply with commercial ply on both faces 6 mm thick as per drawing, for plain lining / cladding with necessary screws, including priming coat on unexposed surface.

Carriage of materials by mechnical mean including loading at source ,unloading at works site and stacking properly ,labour, POL, etc all complete as per direction of E/I.

Brick

Stone Chips

Stone Metal

Power Plug Wiring in PVC conduit (2x4 sq. mm)(used for power circuit):- Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x2.5 Sqmm + 1x2.5 sq mm earth wire(For 5/6A Plug Points)

2x2.5 Sqmm + 1x2.5 sq mm earth wire(For Switch boards)

4 x 10 sq.mm + 2 x 6 sq.mm earth wire

Wiring in existing conduit - Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as required.

2 x 1.5 sq.mm

3 x1.5 sq mm

3 x2.5 sq mm

Telephone wiring in existing conduit :- Supplying and drawing following pair 0.5 sq.mm FR PVC insulated copper conductor unarmored telephone cable in the existing surface / recessed steel / PVC conduit as required. 2 Pair

TV cable in existing conduit :- Supplying and drawing co-axial TV cable RG-6 grand 0.7 mm solid copper conductor PE insulated ,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed steel / PVC conduit as required.

S/F PVC conduit - Supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case recessed conduit as required.

S/F Modular type switch/ socket :- Supplying and fixing of following modular switch / soket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 amps, one way switch

15/ 16 amps, one way switch

5/6 amps, 3 pin socket outlet

15/16 amps, 6 pin socket outlet

Telephone socket outlet

TV antenna socket outlet

S/F Modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

S/F Modular base & cover plate :- Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required.

1/2 module

4/5 module

6 module

8/9 module

12 module

Supply and Fixing Light Plug Point with Modular Type Accessories ( Used for computer point):- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

Supply and Fixing Light Plug Point with Modular Type Accessories (Used for power ):- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. 1200mm (48") BLDC 5star rating 32W Ceiling Fan

Providing and fixing of XLPE, Aluminium Armoured PVC Cable confirming to IS IS7908 (Part-1) 1988 0f grade 1.1KV. Make:- Havells / Finolex / Polycab 10Sq.mm, 4 core

Building Outer Light (50 /60W LED) :- Supply of building outer lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 50/60W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, with 5ft long 40mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65)Make:- Jaquare / Havells/ Wipro/Baja.

Supply and Transportation of 18W LED Down lighter Recessed/Surface mounting made of diecast alluminium body with powder coating acrylic diffuser with driver,Operating voltage range of 150 to 265 Volts AC . cad no 111555-BGSLO Sleek 12 W WhiteMake:- Jaquare / Havells/ Wipro/Baja.

Making holes in walls for laying G.I. / C.P.V.C pipe and restoring the same after pipe laying as per specification and direction of E/I. 250 mm thick wall

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I. Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror - 600mm x 450mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door - 110x110x110 mm

Single tee without door - 110x110x110 mm

Bend 87.5° - 110mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and fixing PTMT grating of approved quality and colour. - C.P. Gratings Circular type - 100mm dia

Non Schedule Items Supply fitting & fixing TES Access Controlled Handle Door Lock Only RFID Card Based Access Control Product ID : 5116877-38720298842

Supply and Instillation of Loop Pile Carpet Tiles (004) as shown in drawing all complete as per drawings, specification and direction of the Engineer in Charge including all costs/ taxes and royalties Product ID : 5116877-7332632573

Supply and Instillation of VISTA Laminate HDF Wooden Flooring 8mm (VISTA Premium Wooden Laminate Flooring) as shown in drawing all complete as per drawings, specification and direction of the Engineer in Charge including all costs/ taxes and royalties Product ID : 5116877-78233021237

Supply and Instillation of Roller Blinds (ULF-BR-2) all complete, specification and direction of the Engineer in Charge including all costs/ taxes and royalties Product ID : 5116877-96743926036

Supply and Instillation of H.P.L Board all complete with screws and bolts for fixing HPL sheet to Aluminium frame , specification and direction of the Engineer in Charge including all costs/ taxes and royalties

Supply fitting & fixing WALL HUNG WC WITH in built Jet UF SOFT CLOSE SEAT COVER, HINGES, ACCESSORIES SET, SIZE:365X515X390 MM SLS-WHT-6951JUFSM - HSN - 6910

Supply fitting & fixing SINGLE PIECE SLIM CONCEALED CISTERN BODY WITH INSTALLATION KIT (WITHOUT FLUSH CONTROL PLATE) JCS-WHT-2400 - HSN - 3922

Supply fitting & fixing Controle Plate Opal JCP-CHR-152415 - HSN - 8481

Supply fitting & fixing 2 way Bib-cock with wall flange FUS-CHR-29041 - HSN - 8481

Supply fitting & fixing Hand Shower/ Health Faucet with 8mmdia 1.2m long flexible tube and wall Hook ALD-CHR-573 - HSN - 8481

Supply fitting & fixing Toilet Roll Holder with S.S. flap Jaquar Make - ACN- CHR-1153S - HSN - 8481

Supply fitting & fixing Grab Bar 300mm AHS-CHR-1501- HSN - 8481

Supply fitting & fixing Thin rim Table top wash basin, shape - rectangular, size 525x415x140mm JDS-WHT- 25907N- HSN - 8481

Supply fitting & fixing Concealed body for single leaver basin mixture wall mounted but without exposed partes ALD- CHR-233N- HSN - 6190

Supply fitting & fixing Exposed part Kit for Single leaver basin mixture (wall mounted) consisting of operating lever, cartridge sleeves, wall flange, Nipple & spout (compatable with ALD-CHR-233N & ALD-235N) FUS-CHR-29233NK- HSN - 8481

Supply fitting & fixing Towel Ring Square AKP-CHR-35721P - HSN - 8481

Supply fitting & fixing Glass Shelf 600mm long AKP-CHR-35771P - HSN - 8481

Supply fitting & fixing Soap Dispencer with Metalic Bottle - ACN-CHR-1137N - HSN - 8481

Supply fitting & fixing Soap Dispencer with Glass Bottle - ACN-CHR-1135N- HSN - 8481

Supply fitting & fixing Wall mixture with provision for over-head shower with 115mm long bend pipe on upper side connecting legs & wall flange - FUS-CHR-29273UPR- HSN - 8481

Supply fitting & fixing Maze- overhead shower 200x200mm square shape single flow (body and face plate S.S. with crome finish) with ribit cleaning system - OHS-CHR-1619 - HSN - 8481

Supply fitting & fixing Shower Arm 20mm dia. And 425mm long round shape with 90 degree bend for wall mounted showers with flange - SHA-CHR-479L450 - HSN - 8481

Supply fitting & fixing Towel rack, 600mm long with with lower hangers in Stainless steel - ACN-CHR-1181S - HSN - 8481

Supply fitting & fixing Soap Dish Holder ACN-CHR-1131N - HSN - 8481

Supply fitting & fixing Bottle trap (with internal partition) 32mm size with 300mm and 190mm long wall connection pipe and wall flangeALD-CHR-769L300X190 - HSN - 8481

Supply fitting & fixing Waste coupling 32mm size full thred with 130mm height ALD-CHR-705L130 - HSN - 8481

Supply fitting & fixing Angular Stop cock with wall flange FUS-CHR- 29053 - HSN - 8481

Add 18 % GST

Add 1% Labour Cess

M/S BHAGWATI PROMOTORS AND DEVELOPERS

M/s Shree Balajee Eng. Co.

M/S JAY GURUDEO ENTERPRISES

BIMAL CONSTRUCTION COMPANY

M/S S.A.CONSTRUCTION