Construction of New Marriage Hall in Arulmigu Kailasanatharswamy Temple at Mappilaikuppam village.

Amount

Installation of Vertial Bored cast in situ RCC piles of basic length 20 Rm in all types of soil with M20 Grade using Ready mix concrete (Sulphate resistant cement supply and erection of reinforcement steel fabrication including cost of binding wire , cutting tying welding and placing the reinforcement case in corret position driving and removing the temporary casing pipe of full depth, shifting the plant an equipment form one point to another carrying out any ancillary works adjacent to pilling works trimming the concrete above cut off level cleaning the debries and levelling the site etc., as directed by the departmental officer. The Rig capacity height of Tower and length of casing pipe etc., must be adequate to take care of change in soil profile. The length of pile for payment shall be measured form Top of show to the bottom of the pile cap. Testing of concrete as specified in IS 456/2000 acceptance criteria as per clause 16.1. Frequency of testing as per 15.2 testing to be conducted at both the end at site as well as RMC plant pile driving depth should be decided by the departmental officers.

450 mm dia pile having longitudinal Main reinforcement of 6 Nos 16# with helical reinforcement of 8# at 150mm c/c etc., complete

300 mm dia pile having lingitudinal Main reinforcement of 6 Nos 16# with helical reinforcement of 8# at 150mm c/c etc., complete.

200mm dia Pile having longitudinal Main reinforcement of 6 Nos 10# with helical reinforcement of 8# at 150mm c/c etc., complete.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

TOILET

Supplying and filling in foundations and the area wherever required below ground level and sides of the foundation and basement with river sand in layers not exceeding 150 mm thick, including well watered and compacting, levelling, etc. complete, and as directed.

Supplying and filling in foundations and basement the area wherever required below ground level and sides of the foundation and walls with Well Gravel filling in layers not exceeding 150 mm thick, including well watered and compacting, levelling, etc. complete, and as directed.

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid). (A. For gradebeam & foundation)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Baesment

Ground floor

First Floor

Second Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Cement Concrete 1:3:6 (One Cement, Three sand and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three Sand and Six hard broken stone jelly).

Brick work in Cement Mortar1:5 (One cement and five sand) using best quality Country bricks of size 8 3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Foundation & Basement

Super sturucture

Brick work using Country Bricks of size 83/4" x4 1/4"x 2 3/4 in Cement Mortar 1:6 (One cement and six sand) including curing neat finishing, etc., complete complying with standard specifiction.

Ground floor

First foor

Second floor

Brick partition walls of 11.50cm thickness using best quality country bricks of size 8 3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground floor hall

First floor hall

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coat with approved Emulsion over the cement plastered wall surface, ceiling and other new surface including clearing preparing the surface curing in all floors including brushes etc., complete as per specification. -10 m 2.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Ground floor hall

Second floor

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following Joint free Rectified Glazed ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles of size 300 x 450 x 8mm set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with pre-polished anti-skid Step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on works . (Sor: M0674) pg.no:70

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Providing & Fixing Teak wood work in frames of doors , Panelled shutters of Main doors , other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length hold fast lugs or dash fastener shall be paid for separately, M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid separtely. above 7'-0" height.

FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and Solid Core FRP Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers.

Supplying and fixing Mild Steel Grills for Windows, Ventilators etc including priming coat complete.

Painting the New Iron Works, in all floors, two coats of best synthetic enamel paint of approved quality, colour and brand ( to be approved by executive Engineer before use on works) over one coat of primer including scrapping and preparation of surface, cost of brushes,high scaffolding charges,neat finishing,complying with standard specification.

Polishing the teak wood door with two coats of best French (Lac) polish with approved quality and brand over a coat of bee's waxing including preparing the wooden surface to receive polishing, etc., complete complying as per the standard specifications. (The make, quality and colour of french polish, bees vax should be got approved by the Executive Engineer before use on works.)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete.

Supplying , fabricating and fixing of Hilux(or) Equivalent Board Falseceiling upto height of 4.50m from floor level using perforated sheets (10mm tk).

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Supplying laying and jointing UPVC pipes of super thick of approved quality and best quality conforming to ISS and with ISI mark of the following sizes including cutting threading and fixing uPVC specials but excluding cost of such specials. Fixing into Bore well / below ground level for erection of compressor motor, suction line air pipe etc., 32mm Dia Pipe.

Supplying, laying and jointing uPVC Pipes of the following dia of approved quality and best variety above ground level including fixing of uPVC Specials but excluding cost of such specials and cutting and threading of pipes but including fixing to the wall with necessary clamps and screws, Teak wood plugs making holes in the wall (or) drilling holes in the roof and making good of the disturbed portion to the oriuPVCnal condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges. etc., complete complying with standard specification.

25mm dia uPVC Pipe

20mm dia UPVC Pipe

Supplying and fixing in position the following uPVC Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of uPVC pipes, jointing the uPVC specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification. (The uPVC specials should be got approved by the Executive Engineer concerned before use on works.)

25mm uPVC Coupling

25mm uPVC Elbow

25mm uPVC Union

25mm uPVC TEE

25mm uPVC Bend

25mm x 20mm uPVC

20mm uPVC Coupling

20mm uPVC Union

20mm uPVC Elbow

15mm Hex Nipple

Supplying and fixing in position first quality and approved variety of Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25 mm dia Gate valve

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped riuPVCd PVC black seat and seat cover with CP brass hingesincluding cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also uPVCving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to oriuPVCnal condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Engineer before use on works)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position best Indian make Wash hand basin of size 550mm X 400mm and approved brand and quality with a pair of C.I. Brackets fixed to wall with necessary teakwood plugs and brass screws one No. of 15mm C.P. Pillar tap 32mm C.P. Waste coupling, rubber plug and chain, 32mm G. I. Union, 32mmG. I. Waste pipe 15mm dia G. M. Wheel valve 15mm brass nipple and nylon connection including cost of white lead TW Plugs clamps, rubber washer, etc., complete (The wash hand basin should be got approved from the Executive Engineer before use on works).

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and uPVCving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to oriuPVCnal condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia door bend

110mm dia plain bend

100mm dia Tee

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing Pvc water tank 2000liters capasity including convenyance loading & loading,inlet & outlet,overflow pipe etc complete.

Supplying of 5.0 HP Submersible Pump ,complete complying with standard specifications.

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Drilling of borewell anywhere in Tamilnadu including transportation from one place to another place with in Tamilnadu in alluvial soil or sedimentary strata of clay and sand or sand, stone, shale, pebbles, boulders etc., by first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia by direct or reverse rotatry mud and circulation method using Contractor's rig, fuel, labour, drilling, betonite mud and water required for drilling at the site shown by the departmental Officers including construction of mud pit (only Calyx drills are to be used).

Drilling of 140/150 mm pilot bore Upto 60 m Depth ending below ground level.

Reaming 140/150 mm dia pilot bore to 300mm dia bore Upto 60 m Depth ending below ground level .

Supply of 150mm medium depth PVC pipe supply of size and quality as approved by the executive engineers of departmental officers.

Supplying and errcting the 50mm dia 6ksc PVC pipes (having working pressure 6 kg. / sq.cm) AS PER IS 4985 /2000.

Labour charges for inserting the PVC 165mm dia casing pipe assembly (with slote or without slote) in the drilled hole including jointing the pipe with PVC couplers with cement paste complete and supplying and packing annuals space with pebbles or size and quality as approved by the departmental officers.

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by departmental officers and conducting yield test by 'V' notch method.

Supplyiing and fixing of suitable 160mm dia PVC endcap (6kg/cm²)for 6"dia borewell of best quality with mark (The PVC pipe should be got approved by departmental officers before execution.).

Supply and delivery of Three phase panel board - D.O.L with two level guard and auto start confirming to IS13947, IEC60947 -1 and as amended time to time.

Supply of 4.00Sq.mm PVC insulated and shethed 3core flat type copper cable for motor pump electrfication confirming tro IS 694/1996 including conveyance to work site etc.

Supplying and fixing in position the following GI Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of GI pipes, jointing the GI specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification. (The GI specials should be got approved by the Executive Engineer concerned before use on works.)

25mm Wheel valve G.M

25mm union G.I

25mm bend G.I

25mm tee G.I

20mm x 15 mm reducer G.I

15mm nipple G.I

32mm wheel valve G.M s.o.r 157(i)=-pg.no-48

32mm Union G.M s.o.r 157(i)=-pg.no-48

32mm bend G.I

Conveying and Reclaiming Filling of Conveyance Earth to be lead of 10km distance Soarrounding for land laying area around building inculiding Earthwork conveying, Dumping and Leveling and Consolidating etc., complete as per Std Specification.

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and fixing AC ventilating shaft of 100mm dia with 3 metre height including cost of 100mm dia AC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and Paving the Paver Block flooring using Rubber mould paver block ( Colour ) of standard size over the sand filling of 83mm thick, including laying Compacting with power machine including loading transportation and colour pigments of paver blocks, including cost and conveyance of all materials labour etc complete with standard specification.

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) (4 Points / coil)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & pumproom, etc.)

Wiring with 3 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylem sheet covered TW switch box and 5A FT switch (two way) and making good of the concealed portion with suitable colour for concealed staircase light point

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.

Supply and fixing of single box type 4' 20W LED fitting complete with TW round blocks on wall of ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 7W / 9W LED for BH point.

Supply and fixing of 24W square type LED fitting with necessary electrical connections.

Supply and fixing of 1200 mm (48") AC HIGH SPEED ceiling fan complete with stepped electronic 300W regulator with 1 mtr down rod on the existing clamp.

Supply and fixing of 450 mm 18" Almonard Wall fan with MS Clamp with bolt and nuts for fixing the fan on wall with necessary connection.

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall.

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan .

Supply and fixing of 450 mm (18") sweep (heavy duty) AC exhaust fan complete with necessary wall opening and making good of the wall.

Supply and fixing of light trap arrangements for 450mm (18") sweep exhaust fan.

Supply and fixing of 5A / 15A 3 pin combined flush type wall socket with 15A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet.

Supply and fixing of 3 Nos. 5A (3 pin and 2 pin) combined flush type wall socket with control switches concealed in suitable TW box covered with hylem sheet in flush with wall with earth connection.

Supply and run of 2 of 2.5 sq.mm. PVC insulted SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 10 sq.mm. PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug).

Supply and fixing of 1.5 TR Split AC with 4 KVA stabilizer (V-guard / Eql) with copper coils 5 star rated of reputed make required accessories and as directed by the departmental officers. (Make: Carrier / Voltas / eql).

Supply and fixing of 230V single phase 25L capacity vertical storage type electric water geyser on wall with MS clamps and necessary accessories with electrical connections complete.

Supply and fixing of 30W LED street light fitting complete with 32mm dia GI pipe (Class 'B') on the existing post or on wall with PVC unsheathed Copper leads MS clamps and aluminium paintings.

Supply and fixing of 90W LED street light fitting complete with 32mm dia GI pipe (Class 'B') on the existing post or on wall with Pvc unsheathed Copper leads MS clamps and aluminium painting.

Supply and fixing of 50W LED flood light fitting complete on wall or ceiling with suitable MS clamp (Model: LFL-50-CDL/60-M Make: Crompton / eql).

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure Distribution board with Double door (Metal) 1 No. 32 AmpsP MCB as incoming and 10 Nos 6 amps to 32 Amps SPMCB outgoing in flush with wall and making good of the conceqaled portion with earht connection only. The MCB DB and MCB's should be with ISI mark (like Legrand make).

Supply and fixing of 100A 6 way Vertical type triple pole neutral MCB distribution board (MAIN) in sheet steel enclosure double door (Metal) with 1 No.100A 4 pole MCB isolator as incoming and 6 Nos 63A FPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark (Like Legrand make).

Supply and fixing of 63A 4 way Vertical type triple pole neutral MCB distribution board in sheet steel enclosure double door (Metal) with 63A 4 pole MCB isolator as incoming and 12 Nos. 6-32A SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark (Like Legrand make).

Supply and fixing of powder coated box on wall fabricated with MS sheet of 16 guage of size 900 mm x 600 mm x 450mm with 3 Nos of 100 A (500 V) porcelain fuse units, 1 No of 100 A TPN sheet steel double break switch with HRC fuse units provision for fixing TNEB meter with electrical connections complete.

Supply and fixing of 100A four pole changeover switch on suitable angle iron frame work with electrical connections complete.

Supply and fixing of 63A TPNMC switch with suitable angle iron frame work with MS cable entry boxes with earth connection only .

Supply and fixing of 3 phase 100A aerial fuse unit for 3 Nos. 100A fuse units (500 V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work on the tapping pole with necessary clamps.

Supply and laying of 3-1/2 x 35 sq.mm. PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and laying of 3-1/2 x 50 sq.mm. PVC LTUG Alu.cable on post or on wall with MS Clamps.

Supply and clamping of 3 1/2 x 50 sq.mm. PVC LTUG armoured LTUG Alu. Cable in 65mm dia Class B GI pipe on post or on wall with MS Clamps.

Supply and frxing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete .

Supply and run of 4 of 16 sq.mm. PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 1 of No. 8 SWG hard drawn copper wire for earht connections.

Supply and providing electrical safety & firefighting accessories complete as detailed below. ABC type 6 kg fire extinguisher (SR) - 2 Nos. ABC type 2 kg fire extinguisher (MR) - 8 Nos. 11 KV Rubber Mat of size 2m x 1m confirming to IS - 3 Nos First Aid Box complete with all First Aid Medicines - 1 No Shock Treatment Chart fixed in glass frame - 1 No Fire Buckets - 4 Nos with MS Angle frame stand - 1 No Hand Gloves 11KV Grade - 1 Pair Danger Board with danger caution sticker notices - 1 Set.

Supply,Erection, commisioning and testing of 30 KVAS Diesel generator with acoustic arrangements in accordance with CPCB norms, water / coolant oil cooled type engine with 38.6 BHPfor 15 KVA generator at 1500 rpm under NTP conditions with following specifications. The engine should have turbo charged, should be provided with air cleaner, base frame, crank case, lubricating oil, fan and fan drive, fuel and oil filters, flexible fittings, exhaust governor, hydro-mechanicalgauges for fuel transfer, jacket with radiator engine oil, safety set ups with engine shutdown system for LLOP including the set of tools, spares as supplied by the manufacturer along with the Engine. The alternator should have brusheless self-excited Y connected, self-regulated of continous rating, developing an output of 24 KW at 0.8 power factor lagging, 415 V, 3 phase, 50 Hz at 1500 rpm with a voltage regulation of + 1% under steady state condition with over speed capacity of 10% for 5 minutes with standing capacity with class H insulation , ingression protection of IP 23 with topicalization. The alternator is to be designed built & tested to IS.BS.IEC or any. The engine should be provided with suitable electrical starting system including, suitable radiator arrangements with suitable fully charged new batteries and with other connecting accessories. microprocessor beased genset controllers display and displayed at phase voltage & currents, Frequency, reverse Power, Genset KVA, KW, KWh, KVAr, power factor, canopy temperature, lube oil pressure, engine temperature, RPM, run hours, number of starts, fuel tank should be fabricated with 14 SWG CRCA MS sheet steel inbuilt removable type sheet metal fuel tank with fuel gauge drain plug and fuel connections, fuel level indicator and with a capacity of not less than 75 Ltrs. Provisions are to be made to filter the sediments, water in the fuel at rear side and provision of vent at top to release the air pressure in the tank. The tank should be filled with a minimum level of fuel for test running on full load. The Generator set should be erectedon a concrete bed to be constructed as per standard as directed by the departmental officers.( Make: Ashok Leyland / eql) (Data N)

SS Dinning Table (72"x18"x28") Leg 2 1/2'' x 2'' x 1 1/2''.Complete complying with standard specifications.

Plastic Chair .

Add GST 18%

O SELVAM