Repair Replacement to Joinery, Plaster, Flooring,Sanitary fittings, Internal water supply other misc bldg wks at Sewar Fort and Parade ground Mil Stn Bharatpur

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by Engineer in Charge

Rendering 15 mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces finished even & smooth complete all as specified and as directed by Engineer in Charge

Ditto all as per Item No 02 but in CM (1:6) other than fair faces finished even and smooth without using extra cement complete all as specified and as directed by Engineer in Charge

M&L for rendering 10mm thick in cement mortar 1:4 on concrete surfaces including finished even & smooth without using extra cement on ceiling complete all as specified and as directed by Engineer in Charge

M & L Preparation of new decorated plastered unplastered surfaces surface of wall including cornices, pilasters etc by brooming down and applying two coats of cement base paint of approved shade on walls with hand roller complete all as specified and as directed by Engr-in-Charge.

M & L Preparation of new decorated plastered unplastered surfaces surface of wall including cornices, pilasters etc by brooming down and applying Three coats of white wash on walls complete all as specified and as directed by Engineer in Charge

M & L Preparation of new decorated plastered unplastered surfaces surface of wall including cornices, pilasters etc by brooming down and applying two coats of oil bound distemper over 3mm wall care putty of approved shade on walls by roller all as specified & directed by Engineer-in-Charge

M&L for three coats of white wash on new plastered or unplastered surfaces ofCeilings including prepration of surfaces complete all as specified and as directed by Engineer in Charge

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoin jambs pillars etccomplete all as specified and as directed by Engineer in Charge

M&L Brick work with sub class 'B' old size bricks bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer in Charge

Ditto all as per Item No 10 but except bricks complete all as specified and as directed by Engineer in Charge

Demolition of PCC in ground floors and pavings not exc 15cm thickness ( below or above ground level ) complete all as specified and as directed by Engineer in Charge

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, 50mm thick finished even and smooth without using extra cement complete all as specified and as directed by Engineer in Charge

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in flooring 40mm thick finished even and smooth with using extra cement complete all as specified and as directed by Engineer in Charge

S&F in repair of glass dividing strips 3mm thick and 38mm wide & fixed in position complete all as specified and as directed by Engineer in Charge

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick over and including 15 mm thick rendering in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer in Charge

M&L for Granite (of any type) tiles/slab in skirting/dados 20 mm thick over baking coat 15 mm thick in cement mortar 1:3, laid and jointed with gray cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including rubbing and polishing complete all as specified and as directed by Engineer in Charge

M&L for coloured Glazed ceramic tiles in vertical surfaces of ,area of each tiles exceeding 0.9 sqm but not exceeding 0.27 sqm 10-15 mm thick over and including 15 mm thick rendering in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer in Charge

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed by Engineer-in-charge.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm bur not exceeding 0.38 sqmm, over 10 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Vitrified Light Shade ceramic tiles 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm , over 10 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Marble tiles 30 cm x 20 cm x 20 mm thick machine cut, in skirting/dado over 15 mm thick screed bedding in cement mortar 1:4, laid and jointed with gray cement slurry and pointed in white cement including cutting and polishing of Makrana white.

M&L for screed bed or bedding layer of cement mortar 1:6, 15mm thick for tiling laying in floor finishes complete all as specified and as directed by Engineer in Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiling to store and rubbish off the premisses complete all as specified and as directed by Engineer in Charge

Dismantling of stone slab and tiles of any description or thickness in floors, etc. complete all as specified and as directed by Engineer in Charge

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer in Charge

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dedo and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Cutting, polishing existing Kota/ marble floor flooring,(three cuttings and mirror polishing) including Manson polishing, levelling certain places to Kota/ marble floor ,necessary repair work complete as directed By Engineer-in-Charge at site

Cutting,Scrubbing,Rubbing, polishing existing Terrazo (Mosaic or Marble) flooring polishing) ,including removing mild water stains,organic spill stains ,scratches ,other marks & levelling certain places to Terrazo (Mosaic or Marble) floor ,necessary repair work complete as directed By Engineer-in-Charge at site

Dismantling and taking up or down the existing unserviceable GI pipe of 15 mm bore and M&L for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer in Charge

Dirro all as per Srl item No 30 here in before but 20 mm dia

Dirro all as per Srl item No 30 here in before but 40 mm dia

Taking up or down old serviceable GI pipe of 15 mm bore Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, trenches etc ) including cleaning complete all as specified and as directed by Engineer in Charge

Dirro all as per Srl item No 33 here in before but 20 mm dia

Dirro all as per Srl item No 33 here in before but 40 mm dia

S&F in repair bib tap of 15 mm dia , cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer in Charge

S&F in repair stop valve 15 mm bore, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed

Dirro all as per Srl item No 30 here in before but 20 mm dia complete all as specified and as directed by Engineer in Charge

S&F in repair brass ball valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed of 20mm bore, complete all as specified and as directed by Engineer in Charge

S&F in repairbrass ball valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed of 25mm bore, complete all as specified and as directed by Engineer in Charge

Dismantling existing water tank and S &F in repair of Rotational moulded polyethylene water storage tanks 500 Ltr white colour triple layer and thraded lid cover with locking arrangement (cylinderical vertical with closed top)with ball brass valves,high pressure , with polythene float and flynut complete, hoisted and fixed in position all as specified in SSR part - I complete all as specified and as directed by Engineer in Charge

S & F in repair of vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, 'P' or 'S' trap, including connection to trap, and to flushing pipe, anti-syphonage pipe etc. complete including making good to floor with PCC, Lime concrete bedding complete all as specified and as directed by Engineer in Charge

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore including taking down old pillar tap.

Dismantling of old existing unserviceable WHB glazed and S&F new vitreous china wash hand basin, white, of size 550x400mm flat back excluding taps, waste, chain and plug but including brackets, cutting for and pinning in ends of brackets or erecting stand complete in repairs.

S&F waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including 32mm PVC waste pipe for WHB complete all as specified and as directed by Engineer in Charge

S&F Sink with drainage board made of stainless steel 1 mm thick Kitchen or Laboratory with plugs, washers and wastes; including beding in cement mortar on to dwarf walls or including fixing cantilever brackets and connecting union to waste pipe overall size 915mm x 460mm bowl size 410mm x 330 mmx160mm.complete all as specified and as directed by Engineer in Charge

S&F in repair of sink made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or with & including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410 x 330 x160 mm including waste pipe of polythelene of low or high density or PVC 32mm dia & waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including making holes in stone walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0 complete. Make of sink - Comet/Neelkamal/Hindustan/ Natraj/Devidayal/ Kitchen Queen/Jaquar

S&F reflection mirror range of size 80*60 cm all as specified make parryware etc complete all as specified and as directed by Engineer in Charge

S&F in repair half turn flush cock of brass of 40 mm bore complete all as specified and as directed by Engineer in Charge

Dismantling of old U/S grating of any description or size and S&F MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap. complete all as specified and as directed by Engineer in Charge

S&F in repair of brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union including taking down of old shower rose of any size, any type.

S&F in repair of PVC low level flushing cistern 10 ltrs capacity with inlet ball valve float & handle, syphonic action type including brackets & flush pipe of polythelene of low or high density or PVC 32mm dia for LLFC fixed in repairs

S&F in repair of aluminium anodised tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges. complete all as specified and as directed by Engineer in Charge

M&Lin repair of cast iron nahani trap of 75mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed by Engineer in Charge

S&Fin repair of PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, ISI marked of 75mm bore ncomplete all as specified and as directed by Engineer in Charge

S&Fin repair of PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked of 110mm bore complete all as specified and as directed by Engineer in Charge

S&Fin repair of UPVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, Type 'B', ISI marked of 75mm bore complete all as specified and as directed by Engineer in Charge

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame).

Taking down shutter of any description area exc 1 sqm and n. exc 2 Sqm each complete all as specified and as directed by Engineer in Charge

S&F 35 mm thick 2nd class hardwood( hollock ) factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 PtI complete all as specified and as directed by Engineer in Charge

S&F 35 mm thick 2nd class hardwood ( hollock ) factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part I. complete all as specified and as directed by Engineer in Charge

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, door chowkats of angle or other section and similar works complete of Gde Fe-290 Gde E-165 including welding etc.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position. complete all as specified and as directed by Engineer in Charge

Factory made steel window with side hung shutteers including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including one shop coat of zinc chromas primer (Note :- Mild steel wire cloth shall be measured and paid separately under respective items)

All as per item No 65 above but without glazing bars. complete all as specified and as directed by Engineer in Charge

S&F Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane. complete all as specified and as directed by Engineer in Charge

Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including S&F 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5 complete all as specified and as directed by Engineer in Charge

Galvanised mild steel wire cloth 0.50 mm nominal dia if wire and average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staples complete as directed by Engineer-in-Charge.

All as per item No 69 above but supply and fix in repairs complete all as specified and as directed by Engineer in Charge

S&F steel ventilator with top hung shutter including hinges,steel peg stay, handle complete in repair complete all as specified and as directed by Engineer in Charge

M&L for cutting opening in cement concrete walls (any description) for door, window and other openings(with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering etc. with or without reinforcement complete all as specified and as directed by Engineer in Charge.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified and as directed by Engineer in Charge

S&F 50 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified and as directed by Engineer in Charge

150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) complete all as specified and as directed by Engineer in Charge

S&F Mild steel presses steel bow handle oval type stove enameled black of size 150 mm (ISI marked) complete all as specified and as directed by Engineer in Charge

Small fitting such as brackets of any type latch and hinge blocks shapped door and window stops and the like n. exc 200 cum each of second class hard wood including all necessary labour complete as directed by Engr-in-Charge.

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified and as directed by Engineer in Charge

S&F in repair of MS spring hinges 300 mm, ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden/ angle iron chowkats complete all as specified and as directed by Engineer in Charge

S&F in repair of 25 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and 3mm thick veneering on both face including french polish in two coat and teakwood lipping on edges of shutters complete all as specified and as directed by Engineer in Charge

S&F hasp and staple of size 100 mm aluminium anodised safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by Engineer in Charge

Painting to new untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of Zinc chrome primer including preparation of surfaces complete all as specified and as directed by Engineer in Charge

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer in Charge

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheeet reinforced with m.s. squre tube complete all as specified and directed.

Supplying & fixing in the frames at site factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified and shown on serial pages No. 142, 143, 144 , 145 & 146 of SSR 2010 (Part-II) and Particular specification. Doors shall be of make :- Rajshri Plastiwood / Sintex /Rotomould / Rotomatic..

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked complete all as specified and as directed by Engineer in Charge

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed complete all as specified and as directed by Engineer in Charge

S&F 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified and as directed by Engineer in Charge

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified and as directed by Engineer in Charge

S & F powder coted Anodised Aluminium frame for door,windows,vantilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed by Engineer in Charge

S & F powder coated Aluminium door shutter,aluminium section weighing 0.55kg/m including necessary joining cleats zlazing clips,rubber neoprene packing handles 2 Nos in each door,hinges anodized aluminium snap beading screw etc complete all as specified and as directed by Engineer in Charge

S&F powder coated Anodised aluminium window and ventilators shutters,side hung type without sash bars,aluminium section weighting 0.55 kg/m including necessary joining cleats,glazing clips,rubber packng,anodised aluminium snap beading,screws,anodised aluminium fitting such as peg stays 150mm long 1 nos ,hinges type B-21 100 mm long Nos suitable handle Nos complete all as specified.

S&F in repair/Replacement double action floor spring hydraulically regulated made up of minium 1.25 mm thich aluminium alloy sheet foundation box,main body with stainless steel cover,govering pivot made of brass,other parts made of mild steel heavy duty and fixed.

S&F Aluminium extruded section body door closer hydranlicelly regulated designation no 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.complete all as specified and as directed by Engineer in Charge

Demolition of cement concrete (unreinforced ) of roof , complete all as specified and as directed by Engineer in Charge

M&L for 40mm thick PCC type B-0,( 1.2.4) using 12.5 mm graded stoine aggregate finished even & smooth without using extra cement.complete all as specified and as directed by Engineer in Charge

M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:4 mixed with water proofing compound as per manufactoring instruction, finished even and smooth without using extra cement over cement slurry over existing roof @3 kg/sqm . WPC Shall be meashured and paid seperatly complete all as specified and as directed by Engineer in Charge

Supply only water proofing compound ISI marked Make : DR Fix) complete all as specified and as directed by Engineer in Charge

M&L APP based polymeric membrane not less than 3mm thick , weighing not less than 3.5 Kg / sqm , and upper side of membrane thermally insulated with white mineral gravel finish , informly embedded during manufacturing process,shall only be used . It shall be laid by torch application .Side over laps shall be 75 mm and the end shall be 100 mm and all overlaps and joints shall be sealed by torch application including applying a coat of cold applied bitumen primer conferming IS:3384 @0.40 Kg/Sqm complete all as specified and as directed by Engineer in Charge

M&L Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the rati of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation, boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed by Engineer in Charge

M&L for providing and fixing Gypsum Board 12 mm thick in ceiling fixed with screws as per manufacturers instructions.

S&F anodised GI snap grid frame work for false ceiling complete all as specified and as directed by Engineer in Charge

S&F hangers 6mm dia. G.i. (up to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long complete all as specified and as directed by Engineer in Charge

Dismantling Asbestos cement (plain or corrugated, etc) sheets in roof coverings complete all as specified and as directed by Engineer in Charge

M & L of Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer in Charge

S&F 6 mm thick asbostos cement, corrugated or semi corrugated sheets in roofs, walls etc fixed with L type or J type or cranked hook bolts.complete all as specified and as directed by Engineer in Charge

Taking down chowkats or frames exc 1.5 sqm but Not exc 4.0 Sqm each without taking off shutters from the frame bolts.complete all as specified and as directed by Engineer in Charge

S&F Sheet glass ordinary quality 5.50 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane. complete all as specified and as directed by Engineer in Charge

M & L of 30 x 6 mm flat iron as in wind ties complete all as specified and as directed by Engineer in Charge

M/s Ranaji Construction Co

krishna Associate

GANGA CONSTRUCTION

Pioneer Enterprises

AMIT RISHABH BUILDERS PRIVATE LIMITED

kant material store