P/O FIRE ALARM SYSTEM IN LDP LAB ALONGWITH CERTAIN MISC WORKS AND PROVN AND INSTALLATION OF MISC E/M AND B/R SERVICES AT CERTAIN LOC AT AFS PUNE UNDER GE (AF) LOHEGAON

Amount

Supply, Installation Testing & Commissioning of microprocessor based Networkable Analogue Addressable Fire Alarm Control Panel. The Panel shall be compliant with EN54-2, EN54-4 and approved by LPCB. The Panel must have Full colour 800 x 480 LCD with resistive touch screen and automatic backlight dimming. The Panel must also have the capability to take Addressable Intelligent Wired and Wireless Devices on same loop. Each loop shall have a capacity of 127 analogue Addressable devices and 127 Base sounders/Base Sounder Beacons. The panel shall have an event log of minimum 10,000 events @ 1 second resolution, Filterable and Printable. The Panel shall have Three access levels. Panel shall support upto 5000 Cause & Effects entries, with upto 20,000 inputs controlling & 20,000 Controlling outputs across the network. The Panel shall have capability for Peer to Peer networking through RS485 network card. The Panel must have 4 inbuilt programmable sounder circuits, each circuit rated at 2.5A.The Panel must have inbuilt 3 programmable inputs and 5 inbuilt programmable relay outputs. The Panel shall have up to sub-addressable 512 programmable Inputs/Outputs via optional RS485 COMMS serially connected expansion cards. The panel shall have zone indicator ranging from 0 to 144. The Panel shall have 240 V AC power supply along with automatic Battery Charger. The Panel shall be fully expandable via common plug in loop driver boards. The user shall have a choice of using the panel with 5.25 Amp or 10.25 Amp power supply unit which is inbuilt in the FACP and should be approved to EN54-4. The Panel shall have configurable via USB port to PC or SD card slot. The Panel shall have dedicated RS232 serial port for optional printer. complete all as specified and directed by Engr-in-Charge.

Supply, Installation Testing & Commissioning of Active Repeater Panel to be integrated via RS485 network card with Fire Alarm Control Panel,larger display Full colour 800 x 480 LCD with resistive touch screen and automatic back-light dimming and the status of any Fire/Fault of Integrated Fire Alarm Panels. The Panel shall have compliant with EN54-2, EN54-4 and complete all as specified and directed by Engr-in-Charge.

Supply, Installation, Testing and Commissioning of Approved Projected Beam Detector Complete set with required module (100mtrs)• Should be Microprocessor based complete all as specified and directed by Engr-in-Charge. • Signal strength LED's • Should Provide linear protection • Automatic compensation for signal drift or dirty lens • Minimum Three field adjustable sensitivity settings • Form A alarm and Form B trouble contacts • Calibrated filters shall be vailable to verify sensitivity • Emitter and Receiver type

Supply, Installation, Testing and Commissioning of Zener Diode Barrier. The barrier shall have, Simple installation onto standard DIN railing, Removable colour-coded terminals for easy connection, accommodate conductors up to 2.5 mm2, Supports up to two zones of I.S. products, Working voltage 26.5 V at 10 µA complete all as specified and directed by Engr-in-Charge.

Supply, Installation, Testing and commissioning of Analogue Addressable Dual Zone Module which is fully compatible with Hochiki’s ESP analogue addressable protocol and I.S. equipment. The module will allow connection of up to 40 Hochiki I.S. conventional detectors (20 per zone) through a Galvanic isolator, which are fully monitored for open and short circuit. The unit also features an integral short-circuit isolator complete all as specified and directed by Engr-in-Charge. (Please note that this module should only be i . Single loop address supports two independent zone,both zone fully monitored for short/open circuit,required an auxilliary 24 vd.c.power supply,Din rail version and have integral Short Circuit Isolator. EN-54 Approved.

Supply, Installation Testing & Commissioning of Analogue Addressable Single Input Module. which Includes a single monitored input, flying leads for easy installation. Electronically addressed, complete all as specified and directed by Engr-in-Charge.

Supply, installation, testing and commissioning of Response Indicator complete all as specified and directed by Engr-in-Charge.

Supply, Installation, Testing and commissioning base Fault Isolator fully monitored for short/Open circuit compatible with Analogue Addressable Protocol,Electronically addressed, approved by LPCB,unit incorparates an amber LED to show when it is islating a section of a Loop complete all as specified and directed by Engr-in-Charge.

Material and labour for supply and fix armored fire cable copper conductor of size 1.5 sqmm two core FRLS in Red colour fixed on wall / roof with GI saddle complete all as specifed and directed by Engineer-in-Charge

Material and labour for providing point wiring with two runs of 2.5 Sqmm multi stranded copper conductor Flame retardant PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core copper stranded Flame retardant PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping with all fittings / fixture etc and open recessed type Plastic Enclosure (Plastic Switch Board) ISI marked (IS 14782) for housing one 15 A Switch / sockets complete all as specified and directed by Engr-in-Charge.

S&F switch socket combination 3 pin,16 Amp flush type complete all as specified and directed by Engr-in-Charge.

Cutting of existing road/hard standing 15 Cm width and 30 CM depth for passing the cable including making good to disturbed surfaces complete all as specified and directed by Engr-in-Charge.

Supplying laying and jointing threading into trenches/wall/floor etc 40 mm bore light grade GI steel water tubing incl all fittings and accessories complete all as specified and directed by Engr-in-Charge.

Dismantling and taking down unserviceable street light fitting of any capacity ,incl disconnecting the cable connections complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of LED security light pressure die cast aluminium housing,heat resistance toughened glass. IP 66 protection, better optics for uniform distribution 75 Watt, 220/215 Volt 50 HZ with 05 KV built in surge protection device complete all as specified and directed by Engr-in-Charge.

Supply laying and testing cable XLPE insulated screened,PVC bedded,galvanized steel strip or wire armoured,electric power cable(heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth and getting it out for laying of cable / pole Soft/loose soil complete all as specified and directed by Engr-in-Charge.

Ditto item above but in Hard/dense soil

Returning/ Refilling of excavated soil including spreading levelling and well ramming in layers for any type of soil complete all as specified and directed by Engr-in-Charge.

Removing the surplus spoil to a distance not exceeding 50 mtrs from the starting point and depositing at a height not exceeding 1.5 m above ground level complete all as specified and directed by Engr-in-Charge.

Material and labour for stone dust sand cushioning to under ground cable, provided with a layer 8 cm before and 15 cm after laying and stretching jointing and testing the cable complete all as specified and directed by Engr-in-Charge.

Supplying and laying un-reinforced precast concrete cable cover, class I, flat, size 250mm x 150mm x 40mm for cable protection complete all as specified and directed by Engr-in-Charge.

M&L Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed as required 2x1.5 sq. mm +1x1.5 sq. mm earth wire drawn in rigid PVC conduit and neccessary accessories complete all as specified and directed by Engr-in-Charge.

Supply and fix in PVC (Thermoplastic) street light junction box, heavy duty with locking arrangement, single phase and neutral connector along with necessary MS clamp, nuts bolts and washers for fixing and one No MCB single Pole 240 Volts 6 Amps complete all as specified and directed by Engr-in-Charge.

Supply and fix GI pipe light grade with all connected accessories of sizes 40 mm complete for road crossing complete all as specified and directed by Engr-in-Charge.

Supply and fix GI pipe light grade with all connected accessories of sizes 25 mm complete for protection of cable complete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6mm as earthing lead buried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised earth lead 25X4 mm dia by means of bolts, nuts, check nuts & washers etc connected to DBs all as shown in electrical plate No.3 of SSR Part I of 2009 & as specified or indicated and testing on completion including excavation / earth work in any type of strata, PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab cover 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm), funnel with wire mesh, watering pipe of 20 mm bore medium grade,including GI strip 25x4 mm dia with GI protection pipe of 15 mm medium grade up to 7.5 meter length etccomplete all as specified and directed by Engr-in-Charge.

Supply, Install, Test and Commissioning of street light panel box out door type fabricated out of 3 mm thick CRCA sheet double door, of size 500x500x300 mm complete with powder coating with seven tank process mounted on M.S angle Iron frame, duly grouted with PCC reqd. with the following specification MCB DP 32 Amps 10KA -1 Nos,digital type street light timer -1 Nos and suitable rating power contactor -01 Nos and internal wiring complete all as specified and directed by Engr-in-Charge.

Supply anf fix 3 phase surge protecting device (SPD) class I(IEC 61643-1) fixed parallel to the existing power supply with following specification:- (a) Ambient Temperature(operational):-20°C to 80°C (b) IEC Category:IEC Class I/EN Type 1. (c) Nominal Voltage:230 ±10% V AC. (d) Nominal Frequency:50 Hz(60 Hz). (e) Maximum discharge surge current Imax: 25 KA (f) Lightning test current(10/350)µs,peak value limp (g) Protection level up(L-N):≤1.5 KV (h) Response time(L-N):≤25 ns (j) Standard compliance:IEC 61643-1(Vendor to produce compliance test certificate:EN 61643-11. (k) Protecting raiting:IP 20. (m) Form Factor:DIN rail type

Supply install, testing and commissioning single phase isolation transformer, air cooled,indoor type, copper wound of capacity 1 KVA with following specifications. (a) Model Rating : 1 KVA/800 Watt (b) Input nominal Voltage - 240 Volt AC Single phase+ 5% (c) Frequency 47 to 63 Hz (d) Power factor >=0.97 (e) Output Voltage 240 V AC (f) Voltage harmonic <=2% linear load (g) Over load capacity 125% for 3 min and 150% for 30 Sec (h) Wave form : Pure sine wave (j) Isolation : Galvanic isolation>1000M Ω between any winding to ground (k) Primary to secondary ratio : 1:1 (m) Potential difference between neutral to earth should be less than one Volt

M&L for Sub Main wiring with four run of single core 10.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 1100 volts grade drawn in rigid PVC conduit with and including PVC insulated 6.0 sq mm earth wire single core multi strand copper conductor as continuous earth wire in green colour connected to common earth dolly complete all as per OEM specification and directed by Engr-in-Charge.

M&L for Sub Main wiring with two run of single core 2.5 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 1100 volts grade drawn in rigid PVC conduit with and including PVC insulated 1.5 sq mm earth wire single core multi strand copper conductor as continuous earth wire in green colour connected to common earth dolly complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick Cement concrete type B-2 , 1:2:4 (using 40mm graded aggregate) as in sub base finished with cement concrete surfaces without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 40mm thick Cement concrete 1:2:4 type B-1(using 20mm graded aggregate) as in flooring, finished surfaces even and smooth with using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound,Grade ‘A’. in 100mm th slab complete all as specified and directed by Engr-in-Charge.

Excavating in post holes (or similar holes) each not exc 0.5 Cum in any type of soil, getting out, returning fillimg in and ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm thick watering and well ramming and removing surplus soil to a distance n, exc 50m and making good surface complete all as specified and directed by Engr-in-Charge.

Cement concrete 1:2:4 type B2 using 40 mm graded crushed stone aggregates in foundation filling and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for Rolled mild steel as in roof trusses (framed), trusses, purlins, crane gantries, rails and fastenings & heavy bracket frame (beam, tee, angle channel or flat section) in distance pieces, cleats etc confirming to Fe-410-W(grade-250, quality"A') including one shop coat of zinc chromate primer paint before fixing in position complete all as specified and directed by Engr-in-Charge.

M&L for mild steel tubular or trusses etc including special shaped washer etc. complete using ERW or induction butt welded tubes, confirming to IS-1161-1979 grade St-240 including one shop coat of zinc chromate primer paint complete all as specified and directed by Engr-in-Charge.

S&F 2.0 mm thick fibre glass re-inforced translucent corrugated sheeting with two corrugation side lap fixed with 'L'-type or 'J'-type or cranked hook bolts complete all as specified and directed by Engr-in-Charge.

S&F 0.80 mm thick mild steel plain, black sheet as in ridge, hip, valley gutter, drip and straight flushing (length & girth as fixed) fixed with L'-type or 'J'-type or cranked hook bolts complete all as specified and directed by Engr-in-Charge.

S&F, 110 mm dia PVC(SWR) pipes,as in rain water pipes, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-Charge.

S&F 110 mm dia PVC(SWR) bends/shoe any radius complete all as specified and directed by Engr-in-Charge.

S&F, Bands, straps, supports or stays for rain water pipes incl bolts, if required and similar small articles confirming to Fe-290, Grade E-165 complete all as specified and directed by Engr-in-Charge.

S&F, eaves gutter 1.0 mm thick mild steel sheet galvanised class 3, half round with rounded edges for 100 mm dia openings complete all as specified and directed by Engr-in-Charge.

S&F, 1.00 mm thick mild steel sheet, galvanised for 100 mm dia stop ends (for spigot or socket ends) complete all as specified and directed by Engr-in-Charge.

M&L painting with synthetic enamel paint two coats including preparing the new steel surfaces of any description over 10cm in width or girth complete all as specified and directed by Engr-in-Charge.

M&L for laying/spreading of sand as in 25 mm thick cushion to precast concrete interlocking paver block incl watering & consolidating complete all as specified and directed by Engr-in-Charge.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, jointed with grey cement and no pigment complete all as specified and directed by Engr-in-Charge.

Plain Cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) in edging of path (interlocking paver) and the like including weathering slightly rounded or chamfered angles as directed including form work and finishig all exposed surfaces complete all as specified and directed by Engr-in-Charge.

S & laying only and jointing, testing and commissioning of LT under ground cable 1100 volts grade XLPE (cross linked polythene ) armoured with galvanised round steel wire or steel strip , electric power cable heavy duty, with multi stranded aluminium conductor, laid in trenches, ducts fix on walls/poles with proper size saddles and clamp laid under roads/path/ drain /colverts or enclosed in GI pipe/ fix complete all as specified , for following size:- a) 10 Sqmm X 2 core

Supplying and erecting ( in true vertical position) steel tubular swaged poles complete with cast iron base plate final taper plug, bolts nuts and screws all as specified of type 410-SP-31 (9.0 mtr length) complete all as specifed in IS 2713 (part-II) 1980 including one coat or red oxide primer and two coats of aluminium paint to exposed surfaces and with blach bituminous paint for embedded portion of pole complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete (1:4:8) type D2 in foundation filling and mass concrete using 40mm graded stone aggregate for pole/stay foundation complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete (1:3:6) type C2 in foundation filling and mass concrete using 40mm graded stone agg for pole/stay foundation complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete (1:2:4) type B1 in foundation filling and mass concrete and coping of poles incl necessary form work using 20 mm graded stone aggregate complete all as specified and directed by Engr-in-Charge.

Supply & fix new junction box of size not less than 35Cm x25 Cm x 15 Cm, made out of Fibre material, shockproof and rustproof, cable entry from bottom. 100% wheather proof, restricted to unauthorised tapping with class FV-0 as per IS : 11731 Part-II or V-0 as per UL-94 and fixing to pole etc using suitable clamps nuts, bolts etc for accommodating and including the following :- (a) MCB DP 10A - 01 Nos

Supply and fix GI Pipe Light grade with all connected accessories of sizes 40 mm complete all as specified and directed by Engr-in-Charge.

S&F in replacement of two run of PVC insulated 2.5 sqmm copper SC conductor cable between cable loops box to fitting drawn through the pole complete. Note: Two run of cable will be measured as one length complete all as specified and directed by Engr-in-Charge.

Supply & fix (in repair) LED street light fitting 60 Watt with LED lamps and driver and made of pressure die-cast aluminium housing IP 65/IP66 road way luminaries (wider beam angle not less than 120 degree, optics with convex lens/pinet lens) with UV stablized polycarbonate cover or toughen glass cover and high power LEDs as light source with LED fittings system Lumen not less than 95 lumen per watt and electronic driver with efficiency 85% with inbuilt protection against lighting, over voltage, short circuit and surge/spike protection upto 5 KV ensuring longer life (THD<10%, PF shall be > 0.95, colour temperature 5700±300K), life expectancy of LEDs minimum 50,000 burning hrs, warranty of complete luminaries fitting shall not less than three years. The fitting shall be tested in NABL accredited LAB and LM 80 test certificate shall be submitted by the original manufacturer. The light fittings shall be fixed on pole with and including 25 mm dia ( or higher size as per manufacturer recommendation), bracket 1.5 m long complete with MS flat iron clamps (clamp shall be 40x5 mm MS flat), nuts and bolts and washers painting the clamps with coat of aluminium paint over a coat of red oxide primer including connection complete all as specified and directed by Engr-in-Charge.

Saviour Security Systems

Modern Engineering Co