Construction of New Bus Stand at Tosham in Distt. Bhiwani (Pdg. Street/ High Mast Light only). RECALL

Amount

Wires and Cables Supply and erection of PVC copper insulated and sheathed 2-core circular flexible wire. (31.9) d) Size 1.50 sqmm ( 48 / 0.20mm).

Main Switches (HSR 31.12 (a) Supply and erection of metal clad switches / B.D.Bs with rag bolts on wall or on existing angle iron board / pedestal including bonding to earth and necessary connections . v) Double pole switch 32 amp. 415 Volts Cat-B,

xiv) Triple pole switch with neutral link 32 amp. 415 Volts Cat-B.

Miniature Circuit Breaker and Isolator. Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. (HSR 31.17) Miniature circuit breakers of 9 KA breaking capacity. ii) SP MCB 6 amp. to 32 amp.

iii) SPN MCB 6 amp. to 32 amp.

iv) TP MCB 6 amp. to 32 amp.

TPN MCB 6 amp. to 32 amp.

Earthing (HSR 31.22) i) Earthing with GI earth pipe 4.5 m long and 40 mm die with masonry enclosure on the top etc. as required .

ii) Extra for using salt and charcoal / coke for pipe earth electrode as required.

xix) Supply and erection of 20 mm x 3 mm thick G.I. tape fixed with suitable G.I. staples of same size.

Under Ground Cables. Supply and erection of underground cable 1 meter below ground level covered with sand and bricks including necessary connections, digging and refilling of trenches. (HSR 31.25) xl) 16 Sq. mm 4 Core Ard. Cable .

xli) 25 Sq. mm 4 Core Ard. Cable .

Supply and erection of underground cable ,loose in existing pipe or trenches complete with necessary connections. (HSR 31.26) xl) 16 Sq. mm 4 Core Ard. Cable .

Supply and erection of suitable compression type brass cable glands for underground Cable. (HSR 31.28) ii) 10 Sqmm to 16 Sqmm Cable 2 to 4 Core .

iii) 25 Sqmm to 50 Sqmm Cable 2 to 4 Core.

Pedestal . Supply and erection of Godrej Almirah type M.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embedded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- (HSR 31.33) iv) M.S.pedestal of size 900 mm wide , 1500 mm high , 450 mm deep and bottom totally open , duly embedded in cement concrete block of size 1050 mm x 600 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster ,having a base of size 1200 mm x 750 mm x 250 mm below ground level.

S/E of double door sheet steel enclosure distribution board suitable for MCBs and ELCBs recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge of the work. (HSR 31.41) i) 4-way, SP&N (Horizontal)

v) 4-way,TP&N (Horizontal)(8+12)

Supply and errection of double walled corrugated (DWC) HDPE pipe laid 1 meter below ground level including digging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including the cost of the labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work. (HSR 31.67) ii) HDPE pipe 90/75 mm outer die / inner die

Supply and errection of Hot Dip Galvanized octagonal pole 3 mm thickness, with base plate including of nut and bolts and all accessories as supplied by the manufacture including cost of foundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galvanized pole complete of 2 nos. 100 A, 4 pole nature links including connection etc with suitable connection arrangements for 2 no. MCB/ kit kat including cost of RCC 1:1:5:3 for foundation of size 0.7 m x 0.7m x 1.8 m with minimum 8 Nos. 12 mm die longitudinal MS reinforcement rods with rings of 8 mm die not more than 200 mm CC for fixing the pole with all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work. (HSR 31.68) i) 7 M long pole with top die 70 mm and bottom die 130 mm with base plate of size 220 x 220 x 12mm.

HIGH MAST POLE Supply, installation, Testing and commissioning of 16 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 Nos. Luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer-in-Charge. (HSR 31.83) Thickness of Top Section = 3mm (Minimum) Bottom Section -4inni (Minimum) Top Dia = 150mm Bottom Dia = 410mm Thickness of Galvanization = Top = 65micron (Min.) Bottom = 85micron (Min.)

Non Schedule Items Supply & Erection of single arms bracket made of 32/50mm dia GI pipe B class ISI 1.20 mtr. Long with coller pipe (GI) 75mm dia 60cm Long top covered with ornamental cap duly welded, painted 2 coats of aluminium paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect upto the entire satisfaction of Engineer-incharge. Bracket duly erected on existing 7/9 Mtr. High Octagonal pole.

S/E of 200 W LED Flood light luminaries with high power LED 120 Lumens per Watt Wipro/ Philips/ Crompton/ Bajaj make in aluminum pressure die casting housing toughened glass cover with IP-66 protection With Lense and dual surge protection device internal 5 KV and external 10 KV including all petty material with labour for errection, complete in all respect of Engineer-in-Charge of the work..

S/E of 60 W LED street light fitting minimum 110 Lumens per Watt Wipro/ Philips/ Crompton/ Bajaj make in aluminum pressure die casting housing toughened glass cover with IP-66 protection With Lense and dual surge protection device internal 5 KV and external 10 KV including all petty material with labour for errection, complete in all respect of Engineer-in-Charge of the work.

S/E of 0.3 KVA capacity inverter with SMF battery for aviation light in existing panel including the cost of all labour & material for connection and petty material etc. to complete in all respect upto entire satisfaction of the Engineer-in-Charge of the work. Make of Inverter -Microteck, Sukam, Luminous Battery make - Exide, Amron