Supply and fixing of Furniture for Government Medical College Doda (Ghat).

Amount

Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resiliance moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the the armrest shall be used black integral polypropylene arm completely joint with seat. The frame structure shall be cantilever support type made up of MS/CRCA powder coated round pipe of Dia 25.4mm with 2mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. The seat size shall be 465±10 mm(W) X 460±10 mm(D) and back size shall be 480±10 (W) X 520±10 mm(H) from seat & overall height = 960±10mm.

Providing and supplying executive table with an overall size 1200mm X 600mm X 750mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The top shall be supported on CRCA C-frame with 0.9mm thick duly powder coated. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 38mm X 25mm with 1.2mm thick. Fixed top supporting pedestal shall be supplied at one side of the table. The pedestal shall be made up of 0.8mm thick high yield strength CRCA sheet of grade 'D' confirming to IS:513. It should have 3 nos. of drawer i.e. 2 box and 1 filing. It should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. The table shall be clad with modesty panel. It should be 18mm thick made up of Pre-laminated particle board.There shall be leveller provided at the bottom. The manufacturer shall have basic quality and safety certifications like ISO-9001:2015, ISO-14001: 2015, ISO-18001:2007, BIFMA Membership & AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Providing and supplying executive table with an overall size 1350mm X 750mm X 750mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The top shall be supported on CRCA C-frame with 0.9mm thick duly powder coated. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 38mm X 25mm with 1.2mm thick. Fixed top supporting pedestal shall be supplied at one side of the table. The pedestal shall be made up of 0.8mm thick high yield strength CRCA sheet of grade 'D' confirming to IS:513. It should have 3 nos. of drawer i.e. 2 box and 1 filing. It should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. The table shall be clad with modesty panel. It should be 18mm thick made up of Pre-laminated particle board.There shall be leveller provided at the bottom. The manufacturer shall have basic quality and safety certifications like ISO-9001:2015, ISO-14001: 2015, ISO-18001:2007, BIFMA Membership & AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supply Installation and Assembly of sofa set( Combination of 3 seater and 2 Seater) Seat :· Understructure: Understructure should be made up of combination of plywood & pinewood members. Plywood should be 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood should be of cross sections 22x64mm, 34x64mm & 16x35mm without having major knots & defects on the surface. Zigzag spring of dia. 3.8mm should be mounted on the seat structure using plastic spring mounting clip for support & additional cushioning purpose. Non woven fabric should be stapled on the seat structure frame above the spring asly. to avoid direct contact between the metal springs and the seat foam. This prevents seat foam from tearing. Powder coated MS support pipe should be fitted with the wooden seat frame to give additional strength to the structure. Complete understructure should be made by gluing, nailing & stapling. · Foam: Seat should be made of PU foam with density 28 kg/m3 with a top layer of supersoft PU foam with density 32 kg/m3. Seat front bottom should be stapled with the PU foam with density 28 kg/m3. · Upholstery: Seat upholstery should be made in polyester fabric, having fabric partitions stitched. 2. Backrest : · Understructure: Understructure should be made up of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 16x35mm & 16x74mm without having major knots & defects on the surface. Non-woven is stapled on the back and front bottom of the structure. · Foam: Backrest is made of PU foam with density 28 kg/m3 which serves as the bottom layer. This should be covered with a top layer of supersoft PU foam with density 32 kg/m3. The top surface has supersoft PU foam with density 32 kg/m3 . The front and the top surfaces of the backrest are then covered with a layer of recron sheet of 200gsm. The back surface of backrest is glued with the PU foam with density 28 kg/m3.· Upholstery: Backrest upholstery is made in polyester fabric. Head cover is draped over the backrest, which can be dry cleaned. Armrest [LH & RH]:· Understructure: Understructure is made of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross section 16x35mm without having major knots & defects on the surface. 3mm MDF and non-woven should be stapled on the structure to provide a surface for sticking foam. · Foam: A layer of EVA sheet should be glued on the top surface of the armrest to give extra cushion. PU foam with density 28 kg/m3 should be pasted on top of this and around the entire armrest. The front and the inside surfaces of the armrest are then covered with a layer of recron sheet of 200gsm. · Upholstery: Armrest upholstery should be made in polyester fabric. 4. Coffee Tray: Three seater sofa has a Coffee Tray made up of powder coated 2mm thk Aluminium sheet. 5. Legs: Plastic legs with the M8 stud are fitted at the bottom surface of the Armrest LH & RH. 6. Assembly: Upholstered seat, backrest, armrest-LH & armrest-RH are assembled together with the M8 bolts, nuts & washer. Then a non-woven should stapled on the bottom surface to cover the structure. 7. Packet: Each packet contains one assembled sofa without legs and a separate hardware packet containing 4 nos. of plastic legs.

Supply Installation and Assembly of center table Providing and Placing CoffeeTable in completely KnockDown Condition having overall centre table of 1200mm x 600mm x 450mm Legs: made of 80mm x50mm 2nd class seasoned CP teak wood section duly polished in melamine. Frame: made out 50mm x 40mm teak wood section and top frame 80mm x40mm i/c necessary rebate for resting of 10 mm thick plain clear toughened glass of size 1.08m x 0.48m i/c beveled edge. All teak wood surface shall be finished with high class melamine polish (matt/glossy) polish in required shade on all exposed portions and spirit polish on unexposed faces complete as per approved sample and direction of Engineer-in-charge. All wood shall be second class seasoned CP teak wood. complete and as per direction of Engineer-in charge..The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, OHSAS:18001, BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA.

Supply Installation and Assembly of corner table roviding and Placing Corner Table in completely KnockDown Condition having overall Size: 450 (W) X 530 (L) X 458 (H). Legs: made of 80mm x50mm 2nd class seasoned CP teak wood section duly polished in melamine. Frame: made out 50mm x 40mm teak wood section and top frame 80mm x40mm i/c necessary rebate for resting of 10 mm thick plain clear toughened glass of size 1.08m x 0.48m i/c beveled edge. All teak wood surface shall be finished with high class melamine polish (matt/glossy) polish in required shade on all exposed portions and spirit polish on unexposed faces complete as per approved sample and direction of Engineer-in-charge. All wood shall be second class seasoned CP teak wood. complete and as per direction of Engineer-in charge.The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, OHSAS:18001, BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA.

Supply installation and assembly of Student desk cum bench grouted to ground with Chemical bolt Bolting should be in scope of vendor Legs should be made of MS ERW tube section (157138) of size 75x25x2 mm thick oval tube with 5 mm thk HR brackets as per IS:2062 and 2mm thk CRCA brackets as per IS-513welded on to the tubes. Assembly is powder coated with epoxy polyester. Leg height varies from 705 to 1005 in pitch of 50 as per layout. Sturdy anchoring by anchor bolts on to base of 8mm thk plate for proper resting of Leg**. Shoe made of ultramid -Nylon are provided at the bottom for covering the base plate. Side dads: Two side clads made of e18 mm thk plate with 0.8mm thk pvc lipping and on the outside covered with welded metal structure made of 2 mm thk CRCA as per 1S-513 powder coated with Epoxy polyester . Worktop: Worktop should be made of 25 mm thick Pre-Laminated Board of El-P2 Grade and approved shade conforming to IS:12823:1990. All the edge of work surface should be provided with machine pressed 2mm thick pvc edge band glued with hot melt glue. Seat: Seat has self closing mechanism which will operate by means of dead weight . Seat understructure should be made from combination of welded fabricated structure of 5mm Thk HR as per IS:2062 and 8mm thk ply as per 1S:303 with moulded PU foam of density 55 kg/cu.mtr. on top which in turn shoule be covered with stitched upholstery made of leatherite as per INT/DSN/MSS/UPH1038 or foam back fabric as per TNT/DSN/MSS/UPH/013.

Supply installation and assembly of Student desk cum bench grouted to ground with Chemical bolt Bolting should be in scope of vendor Seat assembly should be covered on bottom side by means of seat cover made of pp. Seat Back: Seat back is made from combination of 8mm thk ply as per 15:303 with moulded foam on top which in turn is covered with stitched upholstery made leaterite as per INT/DSN/MSS/UPH/038 or foam back fabric as per INT/DSN/MSS/UPHJ013. Seat Support Frame : Seat support frame is made from combination of MS ERW tube section (IS 7138) of size 80x40x2.5 mm thick rectangular tube and MS ERW tube section(IS 7138), of size 48x19.1x2 mm thick oval tube welded together . Assembly os powder coated with Epoxy polyester. CAP made of ultramid are provided from front to cover the oval tubes. Modesty: Modesty is made of 25mm thick pre-laminated twin board of E1-P2 Grade and approved shade conforming to IS:12823:1990. All the edge of modesty are provided with machine pressed 2 mm Thick pvc edge band glue with hot melt glue.

Supply installation and Assembly of table of dimension 1665 Width mm x 900 Depth mm x 740 Height mm . The top shall be 25 mm thick PLB with 2 mm thick PVC Edge Beading plus the Understructure shall be having C - Frames 1.6 mm thick MS supporting the top . The Legs shall be of dia. 38.1 x 1.6 mm thick MS ERW tube .

Supply Installation and Assembly of 2 door almirah with locker 900mm(W)x507mm(D)x1950mm(H) Construction & Material- Aesthetically appealing Slimline, completely knock down construction.  Removable Skirting to cover integral legs.  Legs fitted with screw type leveler  Made from combination of CRCA 0.8 mm & 0.6 mm Thickness. Main Door  Steel Hinged Door. Main Door Locking / handle:  Handle & Base Aesthetically appealing, Ergonomic, flush with door made from Zinc alloy.  3 way 90 Degree Removable key type Cam lock & locking mechanism. Locker Door & it’s locking / handle for Model ‘H’ . Fixed Half locker on RH side  Hinged Door  2 way Cam lock with Knob type handle Finish:  Epoxy Powder coated to the thickness of 50 microns (+-10).

D S AND COMPANY

Unison Furniture Palace