REPAIR/ MAINT TO SWR PIPE, SEWAGE SYSTEM, RAISING MANHOLES, DAY TO DAY CLEANING OF SEWAGE LINES, SEPTIC TANK, SOAK WELLS, MANHOLES, DRAINS AND OTHER MISC B/R WORKS IN TECHNICAL AREA

Amount

SCHEDULE A BOQ

Blocking up the entry of septic tank of the following capacities and pumping out effluent dirty liquid and solid sludge from septic tank including intercepting chambers etc up to bottom collecting sludge and cleaning the septic tank line for reuse and removing the sludge out side to MoD Land and depositing the sludge where directed by local municipal authorities complete all as specified.

200 users septic tank

100 users septic tank

50 users septic tank

25 users septic tank

10 users septic tank

Note for item No 3 to 7 :- The unit rate quoted is deemed to be inclusive for the following :-

(a) Solid sludge means bulky mass of sludge which remains at the bottom of septic tank/soakage well after pumping out/taking out sludge water.

(b) Contractors are advised to ascertain the place suitable/earmarked for disposal of sludge/sewage water from local municipality or area controlling authority before quoting their rates. Disposal of waste at suitable place shall be sole responsibility of contractors and no representation or objection in this regard will be entertained at later stage.

(c) The rate included for excavation of borrow pits for burying of removed sludge under the ground, making good the excavated earth to a true surfaces.

(d) Removing of accumulated earth around septic tank up to 3 m of any width and depth up to 30 cm. cleaning/cutting the grass around septic tank up to 3 m and removing the grass waste to outside MD land. Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be carefully filled up with moorum/red bajri well rammed and levelled.

(e) The complaints to be rectified within SIX hours on same day. The Delay in rectification of complaint more than Six hours, the penalty will be levied @ Rs.100.00 Per complaint/ day.

(f) In case the nature of job is such that the work cannot be completed within a period of 6 hrs then the same shall be brought to the notice of the GE/Engr-in-Charge and the period for the completion of the complaint shall be decided by the GE/EIC.

M&L Vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistren and flushpipe) and including seat cover for pedestal pattern complete fixed including taking down existing damaged one complete as specified and as directed.

M&L Vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of lime concrete bedding fixed including taking down existing damaged one complete all as specified and as directed.

M&L PVC (SWR) 110mm bore P Trap including taking down existing one complete all as specified and as directed.

M&L PVC (SWR) 110mm bore S Trap including taking down existing one complete all as specified and as directed.

M&L Cleaning/ clearing of sewage line (including manholes) 150 mm to 300 mm dia main line from 1st manhole onwards bore of any description, underground at any depth, removing any type of blockage including desludging, descaling & decoking of drain as well as manholes with combined high pressure water jetting cum suction (vaccum) type machine mounted on LCV/HCV /LMV/HMV and having facilities of high pressure vaccum and provn of hydraulic through high pressure thermo plastic fiber based water jetting hose and conical round shape nozzle pipe and flushing after cleaning including removing the same out side MD land and deposit where the place marked by the local municipality, all as directed by Engr-in-Charge

Note for item No 19 :- The unit rate is deemed to be included for Removing of accumulated earth at sides of drain of any width and depth up to 30 cm. cleaning/cutting the grass around 1 m from drain (both sides) and removing the grass waste to outside MD land. Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level . Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be carefully filled up with moorum/red bajri well rammed and levelled.

Cleaning of blockage from nahani traps of bath/kitchen in ground floor and upper floors by taking out mud/sand complete all as specified and as directed.

All as per item No. 21 above but cleaning of blockage from Gully trap to 1st manholes in ground floors.

Cleaning of blockages from water closets in ground floors/upper floor including re-fixing of lid of door bends etc in position after completion of job all as specified and as directed.

Note for item No 21 to 23 :-The unit quoted rate is deemed to be included for the following :-

(a) Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be made good carefully by filled up with moorum/red bajri well rammed and levelled.

(b) Safaiwala shall report to concerned JE /AGE B&R in service centre daily including Sunday and holiday and get the job card for carrying out the work. The Job card shall be returned to concerned JE/AGE duly signed by the users as a token of completion of job.

(c) Cleaning, removal of silts/wastage of organic or inorganic materials of Sewage line of 100mm to 450mm bore up to 1st manhole, in between manholes, GT Chamber, etc to maintain sewage system functional all working days including Sundays and holidays along with necessary T&P i.e flexible rods, cleaning pumps and safety kits etc.

(d) The complaints to be rectified within six hours on same day. The Delay in rectification of complaint more than Six hours, the penalty will be levied @ Rs.100.00 Per complaint/ day.

(e) In case the nature of job is such that the work cannot be completed within a period of 6 hrs then the same shall be brought to the notice of the GE/Engr-in-Charge and the period for the completion of the complaint shall be decided by the GE/EIC.

M&L Grating doom 125mm dia with waste hole of PTMT (minimum weight 40gms) including taking down existing damaged one complete all as specified and as directed.

M&L PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement including taking down existing damaged one complete all as specified and as directed.

M&L PVC (SWR) gully trap 125/110 mm dia of outlet pipe, including jointing with solvent cement including taking down existing damaged one complete all as specified and as directed.

Taking out/pumping contaminated sewage water from Grease trap incl inlet/outlet chamber after plugging incoming sewage line, through suction(vaccum) type machine mounted on LMV/HMV and facility of high pressure vaccum and removing and dumping off the same out side MD land/contonment at the place marked for the purpose by local municipality or the authority controling the area as directed by Engr-in-charge.

M&L Cleaning and Removing silt, grit , mud and other materials from covered drain in foul condition including removing materials from the site to outside MD land including necessary removing cover slabs and replacing after cleaning complete area including making good any damages complete all as specified and as directed.

Demolition of Brickwork/stone boulder masonry, built in cement mortar complete all as specified and directed.

M&L Fly ash Brick work with modular bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 complete all as specified and directed.

Description all as per item No 36 here in above but except bricks. Note:-Serviceable bricks obtained from Sl item No 35 be reused.

Note for Item No 36 & 37 :- (a) Fly ash bricks shall be burnt clay flyash building bricks as per IS- 13757.

(b) The rates for work curved or polygonal on plan include for all extra cutting and extra waste in the body of the work. It shall be measured as mean length of wall.

(c) Sinking of steining shall be measured separately under relevent item. Well curbs, tie-rods, etc. shall be measured under the appropriate item.

(d) bricks shall be of class designation 75 (Kgf/cm).

(e) The quoted rate shall be deemed to be inclusive for all scaffolding, ladders, plant and templates required

(f) Exposed faces of brick work shall be fair.

(g) Exposed faces shall be facing with best bricks

(h) The quoted rate shall be deemed to be inclusive for Plumb to angles

(j) Forming reveals to jambs where fair cutting on exposed faces shall not be involved

(k) The quoted rate shall be deemed to be inclusive for preparing tops and sides of existing walls and the like for raising and extending

(l) Building in vertical seismic reinforcement at the jambs of openings, corners of walls, etc.shall be grouting in cement mortar 1:4

Excavation in trenches in foul position n.exc 1.5m width and n.exc 1.5 m depth and getting out in hard/dense soil complete all as specified and as directed

Excavation in trenches in foul position n.exc 1.5m width and deapth exc 1.5 m but not exc 3mtr and getting out in hard/dense soil, complete all as specified and as directed.

Note for Item No 49 & 50:- (a) Excavating either straight or curved on plan

(b) Clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30 cm girth (measured one metre above ground level) and removing rubbish upto a distance of 50 metres outside the periphery of the area under clearance except in the case of surface dressing which includes for all the foregoing except clearing away of trees

(c) Bailing out, pumping out or otherwise removing all water which may accumulate in the excavations

(d) Setting out the work profiles, etc. as well as for all tools and plant

(e) All materials and labour required protecting against risk of accidents, etc.

(f) Watching and lighting, whenever necessary.

(g) Forming (or leaving) ‘Dead men’ or ‘Tell tales’ in borrow pits and their removal after record of measurements where required

(h) Forming (or leaving) steps in sides of deep excavations and their removal or covering up, after record of measurements

(j) Excavation for insertion of planking and strutting where required

(k) Removing slips or falls in excavations

(l) Authorised battering or benching of excavations

(m) Slinging or supporting pipes, electric cables, etc. met with during excavation

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified.

Removal of excavated material to a distance exceeding 1.50 Km and not exceeding 5.00 Km and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L Plain Cement Concrete (1:4:8) type D2 (using 40 mm graded stone aggregate)as in foundations, filling and mass concrete including demolition of existing concrete complete all as specified and as directed.

M&L Providing cement concrete type C1, 1:3:6 (using 20mm graded crushed stone aggregate) as in surface channels and drains including demolition of existing one complete all as specified and as directed.

M & L Extra for forming fair finished drain or channel of 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc. complete all as specified and as directed.

M&L Rendering 15 mm thick in two layers on brick or concrete surfaces with first coat 10mm thick in cement mortar 1:4 and 2nd coat 5mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete all as specified and as directed.

Note for Item No 68 :- (a) Water proofing compound shall be measured and paid seperately.

(b) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

Supply Only integral water proofing compound complete all as specified and as directed.

M&L in repairs PCC (1:2:4) Type B1 (using 20 mm graded stone aggregate) as in coping including necessary form work finished fair and even surface without using extra cement including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position complete all as specified and as directed.

M&L Precast RCC 1:2:4, Type B–1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, Chajjas, water troughs, mangers, Shelves and similar articles with plain faces including formwork, set in cement mortar 1:4 complete all as specified and as directed.

S&F High strength corrosion resistant TMT bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified.

M&L Salt-glazed stoneware drain pipes, 200 mm bore, laid in trenches and jointed as specified, complete including taking down existing damaged pipe,of any size including damaged haunching/ bed concrete etc complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate) as concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of size 200 mm bore of pipe, complete all as specified and as directed.

M&L Salt-glazed stoneware drain pipes, 150mm bore, laid in trenches and jointed as specified, complete including taking down existing damaged pipe,of any size including damaged haunching/ bed concrete etc complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate) as concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of size 150 mm bore of pipe, complete all as specified and as directed.

Material and Labour for Granite work (of any type) 18 to 20mm thick (table rubbed and polished including round edge) in steps, jambs, pillars, windowcills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over and including 15mm thick screed bed in cm 1:4 including dismantling existing one complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe ,waste pipe etc (excluding flushing cistern and flush pipe ) complete all as specified and directed by Engineer-in-Charge .

S&F in repair Vitreous china urinal partition white of size 32.5 x 69 cm of Cat No 61001 of Hindware or equivalent in Jaguar / Cera, fixed about 40cm above floor line, complete all as specified and directed by Engineer-in-Charge .

M&L 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing damaged PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed.

M&L 150 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing damaged PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed.

M&L 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed.

M&L Salt-glazed stoneware drain pipes, 100mm bore, laid in trenches and jointed as specified, complete including taking down existing damaged pipe any size including damaged concrete in haunching/base etc complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate) as concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of size 100 mm bore of pipe, complete all as specified and as directed.

M&L PVC (SWR) bends any radius 110 mm dia fixed to wall including taking down complete all as specified and directed.

M&L PVC (SWR) bends any radius 75 mm dia fixed to wall including taking down complete all as specified and directed.

M & L 100mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates), laid in 1:20 slope as in hardstanding/ path including making joints @ 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement including demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness and rubish material shall be disposal to out side MD land complete all as specified and as directed. Note :- The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm.

M&L Chequered cement concrete tiles 30cmx30cmx25mm thick machine pressed set jointed and pointed in neat cement slurry as in floors and cut and polished using grey cement and pigments over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) including demolition of existing tile complete all as specified and directed. Note : The manufacturer's test certificate for tiles must be submitted for approval by the concerned authority.

Taking down chowkhat or frame(wooden/steel) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S & FSolid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tubecomplete all as specified .

Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

M & L 100 mm long aluminium, anodised, barrel tower bolts of extruded section including taking down existing one complete all as specified and directed

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

Supply and fixing 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs jindal or Equivalent aluminium anodised ventilator/window with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and two portion to be provided with 4mm thick plain glass fixed shutter and remaining one portion to be louvered using 4mm thick glass louvered portion incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified.

S&F in repair powder coated aluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 37x19x2mm complete all as specified and as directed.

Taking down carefully any type of steel rolling shutters, of size exc. 5 Sqm but n. exc. 15 Sqm each , inspecting/notifying the defective springs, bearings, shaft, side guides, Gear box, Gear box, etc including greasing and replacement of unserviceable/ defective parts and re fixing in the same and releasing the tension in the springs, lowering complete all as specified and directed by Engineer - in - Charge

S&F 6mm thick frame less bevelled edge mirror fixed with steel stud including taking down existing one complete all as specified and as directed by Engineer-in-Charge.

M&L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel covert governing pivot made of brass, other parts made of mild steel heavy duty including taking down existing wire cloth complete all as specified and directed.

S&F Aluminium body door closer hydraulically regulated,designation No.3, universal type, suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 kg and fixed including taking existing one complete as directed by Engr-in-charge.

S&F in repair sinks made of stainless steel 1 mm thick with washers,wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets an connecting union to pipe ,overall size 495mmx420 mm and bowl size 410 mm x 330 mm x160 mm complete all as specified and directed.

M&L White seat cover only of Niagara coupled closet with all fittings including taking down existing one Complete all as specified and as directed Cat Part No C8176 fittings series of Niagara of Parryware or equivalent.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

M&L Joist, channel, angles or tee sections fixed independently, without connection platess Fe-290 Gde E-165 etc all as specified and as directed

M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted , bolted or welded attachment.(Fe 410 -W (Gde- E-250) quality -A complete all as specified and as directed.

S & F in repairs Stack clamps made out of 50 mm x 3 mm flat iron and 100 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore pipe complete all as specified and directed.

M&L Applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new or previously untreated steel surfaces of any description exc 10cm width or girth complete all as specified and as directed.

Note for item No 110:- (a) Synthetic enamel paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

M&L Low density polyethylene (LDPE) pipes 32 mm bore of pressure rating 6 kgf/sqcm for sink/ wash basin including taking doen old unserviceable LDPE pipe complete all as specified and as directed.

M&L Cutting into existing manholes for connecting new drains, making good pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4 type B-1 using 20mm graded stone aggregate) smooth finished and reforming benching as required 150mm internal bore, complete all as specified and as directed.

S&F Chromium plated Urinal spreader for fixing with 15mm dia pipe complete all as specified and as directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and provision of new Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size exc 0.09 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as specified and as directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and provision of new Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado including 10mm thick 1:3 backing coat complete all as specified and as directed.

S & F in repairs PVC (SWR) branch piece single (single Y) 75mm bore equal or unequal provided with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) branch piece single (single Y) 110mm bore equal or unequal provided with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) 75mm bore junction (single T) equal or unequal provided with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) 110mm bore junction (single T) equal or unequal provided with access door complete all as specified and as directed.

M&L Cutting salt-glazed stoneware drain pipe 150mm bore in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 and making good, complete all as specified and directed.

M&L Cutting salt-glazed stoneware drain pipe 200 mm bore in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 and making good, complete all as specified and directed.

M&L Cutting salt-glazed stoneware drain pipe 100 mm bore in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 and making good, complete all as specified and directed.

S & F in repairs Stack clamps made out of 50 mm x 3 mm flat iron and 160 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof suitable for 110 mm bore pipes complete all as specified and directed.

M&L Non - skid coloured Ceramic tiles joint free 7 to 8 mm thick (square/ rectangular) area of each tiles exeeding 0.06 sqm but not exeeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer of motar 15mm thick in cement mortar 1:6 for laying floor finish ,over 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as levelling course including demolition of existing floor complete all as specified and as directed.

supply and fixing in repairs vanitary counter top wash basin (Jaquar - Thin rim table top basin, size 415 x 415 x 145mm round) with MDF cabinet of size 723 x447 x735mm complete all as specified and as directed.

S& F in repairs Vitreous china wash down water closet pan (pedestal pattern) wall hung type, Compact (snow white) carona seat cover 490 x 350 x 330 mm, hinges, fixing accessories with concealed flush cistern fittings, S trap -300mm complete fixed complete all as specified and as directed.

S & F CP pillar cock pressomatic auto closing fancy type 15mm dia CP with capstan head screwed down high pressure screwed for iron pipe CAT Part No-Sl. No-PRS-031 Jaquar Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

S & F in repairs 20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed.

Note for item No 136 :- (a) The unit rate shall be include for taking down existing pipe and connections and all fittings as directed.

(b) The unit rate shall be include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

M&L 25mm outer dia of pipes PPR gate valves (brass insert) including taking down damaged existing one complete all as specified and directed.

M&L Pillar taps 15mm bore CP with capstan head screwed down high pressure screwed for iron pipe Cat Part No QT F2006101 of CERA or equivalent to /Parryware/Hindware including taking down existing one complete as directed by Engr-in-charge.

M&L Bib Cock with wall flange screwed down screwed for iron pipe 15mm bore CAT Part No QTF 2006151 of CERA or equivalent to Parryware/ Hindware including taking existing one complete as directed by Engr-in-charge

S&F CP 2 way bib cock with wall flange fancy type screwed down screwed for iron pipe 15mm bore CAT Part No-Sl. No- QT F2006163 of CERA or equivalent in Parryware ,or as per list of makes Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F CP Hand shower (Health Faucet) with 1.20M braided hose pipe with 8mm bore wall hook with N.R.V (Back Flow Preventor) CAT Part No-S. No-F8030401AB of CERA equivalent in ESSCO/ Kohler as per list of makes Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 Ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repair Towel rail 24" long for wash basin (Make : CAT Part No- F 5002103 of CERA series or equivalent make of hindware / parryware all as specified and as directed.

M&L Angular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, CAT Part No G3007A1 of Parryware or equivalent to Hindware/Cera including taking down existing one complete as directed by Engr-in-charge.

S & F 20 MM bore dia of pipe Ball brass valves. high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule including taking down existing one complete all as manufactures and all as specified and directed by Engineer- In - charge

M&L in repairs for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size, polished confirming to IS-15658 of 60mm thickness M-35 grade, laid over and including M sand cushion of 50mm thick and packing the sides with PCC 1:3:6 complete all as specified and directed. Note : The Unit rate quoted is included for Demolition of Stone Slabs and tiles of any description or thickness in floors,aprons etc laid bedded and pointed in any mortar and removing of debris outside of MD land

NAVEEN ENTERPRISES

D.R ASSOCIATES

T C KARUNANITHI

p.chinnasamy

K S MUTHU CONSTRUCTTIONS

KSR AND COMPANY

KAARTHIC BUILDERS

SARASWATHI CONSTRUCTION