SPECIAL REPAIR TO BLDG NO P-108 AT BHAGAT ENCLAVE AT LGJ MIL STN

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) complete all as specified and directed by Engr-in-charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specificlly provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engr-in-charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engr-in-charge.

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-charge.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 on wall finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for rendering, 10 mm thick on brick work or concrete surfaces in cement mortar 1:4 on ceiling finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for two coats of oil bound distemper on newly plastered surfaces of walls paint over 3mm thick wall care putty including preparation of surfaces complete all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatment and two coats of oil bound distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engr-in-charge.

M&L for 3 coats of white wash on newly / old plastered surfaces of Wall including preparation etc. complete all as specified and directed by Engr-in-charge.

M&L for 3 coats of white wash on newly / old plastered surfaces of ceiling including preparation etc. complete all as specified and directed by Engr-in-charge.

M&L for two coats of cement base paint on newly / old plastered surfaces of wall incl preparation etc. complete all as specified and directed by Engr-in-charge.

M&L washed stone grit plaster on exterior walls in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement : 1/2 coarse sand : 2 stone chipping 10mm nominal size) (using white cement in place or ordinary cement in the top layer) in panels with groove all around as per approved pattern incuding scrubbing and washing, the top layer with bruses and water to expose the stone chippings complete all as specified and directed by Engr-in-charge. Note :- payment for providing groovs shall be made separately

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of wahed stone grit plaster as per approved pattern using wooden battens, naild to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer-in-Charge.

Providing and Applying rising damp proof coating system with single component ready to use damp proof coating Roff Hydamp 1. Preparation :- Throughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc all large voids and hallow portions must be removed and re-plastered non moving cracks having width upto 5mm must be filled with polymer based crack filler. 2. Application :- Apply the first coat of Dr. fixit dampguard classic with a paint brush directly on the prepared surfaces by mixing (1 part base : 1 part hardner : 1 part of water), allow to dry for a minimum 2-3 hrs. apply one part of Dampguard mixed chemical and 2 parts of OPC white cement / Birla putty and make the putty, apply putty on the entire surface area, allow to dry for at least 3-4 hrs, apply the final coat of air cure 48 hrs proceeds for paints.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by Engineer-in-Charge.

M&L for Virified Ceramic tiles 8 to10 mm thick (square/ rectangular) light shed polished, area of each tiles not exceeding 0.36 sqm, in floor etc. over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for Virified Ceramic tiles 8 to10 mm thick (square/ rectangular) light shed polished, area of each tiles not exceeding 0.36 sqm, on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for glazed ceramic coloured tiles of size 450 x 300 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engr-in-charge.

M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid over cement screed base laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as specified and directed by Engr-in-charge.

M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as specified and directed by Engr-in-charge.

Surface excavation N.exc. (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by Engr-in-charge.

Removing excavated materials n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed by Engr-in-charge.

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stones size 300mm x 300mm x 100mm with plain fair faces, including chamfers, weathering, throating etc setting in CM 1:4 complete all as specified and directed by Engr-in-charge.

M&L for hard core of broken stone or boulders of gauge not exc 63mm deposited, spread & levelled in layers not exc 15cm thick, including watering and ramming to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base below floors complete all as specified and directed by Engr-in-charge.

M&L Machined pressed precast concrete interlocking paver block glossy with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with over 25mm thick Fazilka sand cushion complete all as specified and directed by Engr-in-charge. Note : Sand will be measured and paid seperatly

Suply only 25mm thick Fine aggregate (sand) for Cushioning (Fazilka sand) complete all as specified and directed by Engr-in-charge.

Formwork to chajjas, troughs and similar items including edges, for rough surface of concrete complete all as specified and directed by Engineer-in-charge

M&L for reinforced cement concrete 1:1.5:3 type A-1 using 20mm graded stone aggregrate in Chajjas complete all as specified and directed by Engr-in-charge. Note : Reinforcement shall be measured and paid seperately.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clip all as specified & directed by Engineer-in-Charge.

S&F mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clip all as specified & directed by Engineer-in-Charge.

Cutting into existing manholes for connection of new drain making pipes and rendering cutting out existing benching & forming branch channel in PCC 1:2:4 type B1 smooth finished & forming benches as reqd etc for 150 mm bore all as directed.

M&L for broken brick boulder hard core of gauge, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-charge..

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and directed by Engr-in-charge.

M&L continous brick edging with fly ash bricks old size bricks, with width equal to the width of the brick; liad dry on end vertically complete all as specified and directed by Engr-in-charge.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 all as specified.

M&L for PCC 1:2:4 type B1 using 20mm graded aggregates as in benching / haunchig of manholes including forming channels including necessary formwork etc.complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:2:4 type B1 using 20mm graded aggregates as in coping and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary formwork etc. complete all as specified and directed by Engr-in-charge.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate and set in cement mortar 1:6 as in cover slabs (for manholes etc,) chajjas, shelves and similar articles with plain faces complete all as specified and directed by Engr-in-charge.

M&L moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed by Engr-in-charge.

Supply and laying DWCPE (SN8) drain pipes 150mm inner dia as per IS-16098 (Part-II), laid in trenches on moorum bed to required slope, including all assessories / fittings, jointing and tested complete all as specified and as directed by Engineer-in-Charge. (Make :- Rex Polyextrusion Limited/ Dura line / Alom Poly Extrusions Ltd / Jain Irrigation

Dismantling of brick tiles in floor laid dry and pointed in cement morter complete all as specified and as directed by engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and as directed by engineer-in-Charge.

M&L PCC (1:5:10) using 40mm graded stone aggregate as filling of sunken floors/bottom and side of drain complete all as specified & directed by Engr-in-charge.

Material and labour for creating fillet caving 50x50mm with polymer modified mortar on the junction of slab and wall as per manufacture instructions, Material and labour Providing for applying two coats of two component (1 part Liquid: 2 part Powder) ready to use cementitious waterproof coating on properly prepared surface by brush having elongation of >50% for the applying water proofing treatment as per following and complete all as directed by the Engineer-in-Charge. (i) Applying 1st coat of two components modified polymer coating on horizontal and verticle surfaces. (ii) Provn of glasses fiber mess of 2x2mm immediately on alone coating. (iii) Applying 2nd coat of two components modified polymer coating after 72hrs on horizontal and verticle surfaces. NOTE:- Complete treatment to be carried out by authorised applicatior of waterproofing manufacture. Make : Dr Fixit/Fosroc/BASF/STP

M&L for Roof treatment to RCC roof as follows:- (a) Cleaning the roof surfaces thoroughly using wire brusehes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/plaster etc. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with WPC, finished even and smooth without using extra cement. (c) Providing one coat of approved bituminous primer @100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP membrane,(mineral finish) reinforced with non woven polyster fabric, by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by E-in-Charge. Make : STP Dr Fixit/Pidilite, Texsa India Ltd/Tikitar Dansona/Bengal Bitumen Notes : (i) All joints and change in directions should be covered wih cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/as per site reqmt and cured well before laying membrane by torching. (ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only. The name of firm shall be got approved from GE before carrying out the wk. (iv) The independent testing of membrane for technical parameters given in particular specifications shall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarnatee of treatment shall be for min 10 yrs reckoned from date of completion of whole wk.

M & L Lime concrete terracing as specified in roof (excluding bitumen tack coat) complete all as specified and directed by Engr-in-Charge.

M&L 40mm thick brick tiles laid flat on lime concrete & joints grouted flush in cement mortar (1:3) bedded in 15mm th cement morter (1:6)mixed with 5% of crude oil by weight of cement on lime concrete complete all as specified and directed by Engr-in-Charge.

,---ditoo--- all as per serial item No 52 above but except tiles complete all as specified and directed by Engr-in-charge.

M&L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, and like rounded or chamfered on edges including necessary form work etc complete all as specified & directed by Engr-in-Charge.

M&L racking out joints/pointing to brick work or brick tiles laid flat in floors, surface channels, roofs etc. and flush pointing to bricks laid flat or brick tiles in pavings and roofs in CM 1:3 complete all as specified and directed by Engr-in-charge.

Material and labour for repair to damage RCC coloumns/Beam/Slab/Chajja by using micro mortar and concrete in Following Stages :- (a) Removing the mortar and loose concrete from RCC elements. (b) Cleaning the rusted reinforcements and applying rust removal. (c) Inserting the addl reinforcements in cape the coves sectional area reduction in more than 20 percent welding the reinforcement with existing area and supporting adequate on walls if reqiurd with grout. (d) Providing micro morter and concrete over bond coat to cover the reinforcements and slet surface. (e) Providing adequate from wave and scaffolding if required. (f) Curing the surface. Note :- (i) Rust removal, bonding agent, grout, micro morter and concrete and related chemicals shall be of Dr Fixit/BASF and STP (ii) Work is to be got executed from authorised applications and company. (iii) Steel measured and paid separately

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engr-in-charge.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engr-in-charge.

Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each all as specified and directed. (Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.)

Supply and fixing of Fibre glass Reinforced plastic (FRP) door frame of required built in colour in three legged of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and as directed by Engineer-in- charge.

Supply and fixing of 30 mm thick glass fibre reinforced plastic (FRP) paneled doorshutter confirming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin, moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings, cast molithically with 5mm thick FRP laminated for panels including fixing to frames, complete all as specified and as directed by Engineer-in- charge.

S&F framed work as in chowkats of doors windows of angle iron , gates or other section with gusset plates, rails, braces etc conforming to Gde Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

S&F hold fast of flat iron 25 x 3 mm conforming to Fe-290 or Fe 330 including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified & directed

S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-charge.

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed by Engr-in-charge.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anosied and fixed type B-21 all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed by Engr-in-charge.

S&F 125 mm long aluminium anodised handle, cast type complete all as specified and directed by Engr-in-charge.

S&F 150 mm long extruded aluminium alloy handle, fabricated type anodised complete all as specified and directed by Engr-in-charge.

S&F 100 mm long butt hinge, medium weight, cold rolled mild steel complete all as specified and directed by Engr-in-charge.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engr-in-charge.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia fixed all as specified & directed by Engr-in- charge.

S&F as 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as directed.

,---ditto--- All as per item No 74 above but fixed in repairs complete all as specified and directed by Engr-in-charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sqm in each pane complete all as specified and directed by Engr-in-charge.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engr-in-charge.

M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engr-in-charge.

M&L preparation of old painted wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint all as specified.

S&F powder coated aluminium frame/shutter for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect all as specified & directed by Engr-in-Charge. Make of Al Section : Jindal / Hindalco / NALCO

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing exc 0.55 Kg/m (1.50 to1.80mm th) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (01 No) hinges type B-21 100 mm long (2 Nos) suitable handle (01 No) in each window shutter and necessary accessary as required complete all as specified and directected by Engr-in-Charge. (Note : Glass will measured and paid separately) Make of Al Section : Jindal / Hindalco / NALCO

S&F Neoprene / EPDM rubber gasket all as specified and directed by Engineer-in-Charge. (taken for other other than door/window shutter if reqd)

M&L 4.8 mm thick sheet glass, ordinary quality and glazing with aluminium snap beading of any size of glass in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engr-in-charge.

S&F powder coated standard aluminium anodised grill size of mesh 75mm x 75mm and 8mm thick section using U channel 25x12mm complete all as specified and directed by Engr-in-charge.

M&L for Cement concrete 1:3:6 type C–1 (using 20mm graded crushed stone aggregate) as in coping, hold fast, bed blocks or similar block etc complete all as specified and directed by Engineer - in - Charge.

M & L for painting steel and iron surfaces of any discription,over 10 cm width or girth, with preparation of old painted surfaces priming with two coat of read oxide & finish with two coats of synthetic enamel paint ordinary tint all as spefified and directed by Engr-in-Charge.

M & L for painting steel and iron surfaces of any discription,over 10 cm width or girth, with preparation of new or previously untreated surfaces priming with one coat of read oxide & finish with two coats of synthetic enamel paint ordinary tint all as spefified and directed by Engr-in-Charge.

S&F drapery stainless steel rods, standrad quality, not less than 25mm dia with heads at both ends and middle support, rings, etc. complete all as specified and directed by Engr-in-charge.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-charge.

S&F in repair brass hat pegs, solid body, 125 mm to 175 mm (4 legs) complete all as specified and directed by Engr-in-charge.

S&F towel rails 20mm dia 600mm long brass chromium plated superior quality brass chromium plated fancy type complete all as specified and directed by Engr-in-charge.

S&F in repair chromium plated fancy type soap dish complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous china squatting pan Orissa pattern size 580 x 440 mm white with integral foot rests (excl flushing cistern) but including CI 'P' trap set in and including concrete fixed.

S&F in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed by Engr-in-charge.

S&F in repair vitreous china wash hand basin coloured Flat back of size 550x400mm, long screwed shank fly nut flange end including cutting for and pinning in ends of brackets in 1:3 CM including 32mm dia chromium plated waste coupling/trap complete all as specified and directed by Engr-in-charge.

S&F pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified and directed. Note : Wt should not be less than 450 gms

S&F in repair bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, hand operated, screwed for iron pipe or for brass ferrule all as specified.

S&F in repair CP brass stop/angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup fixed complete all as specified and directed by Engr-in-charge.

S&F in repair CP brass stop valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup (Concealed type) fixed complete all as specified and directed by Engr-in-charge.

S&F in repair, shower rose, 125 mm size, brass chromium plated with sweivel joint complete all as specified and directed by Engr-in-charge.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engr-in-charge.

Dismentling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site complete all as specified and directed by Engr-in-charge.

S&F rotational moulded polythene water storage tank 500 ltr capacity, ISI marked vertical with closed top hoisted and fixed in position all as specified in SSR part-I complete all as specified and directed by Engr-in-charge.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair all as specified and as approved by GE/Engineer-in-Charge.

S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe complete all as specified and directed by Engr-in-charge.

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re-fixing the serviceable pipe complete all as specified and directed by Engr-in-charge.

,---ditto---all as per item No 107 above but 20mm dia pipe complete all as specified and directed by Engr-in-charge.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as directed.

,---ditto---All as per item No 109 above but 15mm dia pipe fixing only complete all as specified and directed by Engr-in-charge..

,---ditto---All as per item No 109 above but 20mm dia pipe complete all as specified and directed by Engr-in-charge..

,---ditto---All as per item No 109 above but 20mm dia pipe fixing only complete all as specified and directed by Engr-in-charge...

Dismantling of cast iron pipes, jointed in cement mortar and tabing out of trenches if required upto 100mm dia complete all as specified and as directed by engineer-in-Charge.

Dismantling of cast iron pipes, jointed in cement mortar and tabing out of trenches if required 75mm dia complete all as specified and as directed by engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overalll as fixed along the cente line over fittings and accessories) complete all as specified and directed by Engr-in-charge..

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engr-in-charge..

S&F in repairs 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engr-in-charge..

S&F in repair stainless steel Trap with grating round or square 150mm size (minimum weight 100gms) complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

S&F in repair stainless steel kitchen plate rack made out with 1mm thick sheet of size 24" x 24" x 10" including taking down existing wooden plate rack complete all as specified and directed by Engineer-in-Charge.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm all as specified.

Supply & fixing 100 mm bore cast iron hubless pipe waste and vent pipe in any length with or without ears laid in trenches/floor/wall including clamps, jointing with necessary coupling complete all as specified & directed by Engr-in-charge.

S&F in repairs cast iron type hubless P trap/CPWD floor trap 100mm bore with CP grating including jointing to waste pipe fixed with necessary coupling arrangement complete all as specified and directed by Engineer-in-charge.

S&F in repair 100mm bore cast iron hubless type door T equal/uneqal branch pieces (any radius) diminishing pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified and directed by Engineer-in-charge.

S&F in repair 100mm bore cast iron hubless type plain bends (any radius) dimining pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified and directed by Engr-in-Charge.

Supply only 100 mm bore sheilding (ss) coupling (with EPDM rubber as per requirement complete all as specified and directed by Engineer-in-charge.

Supply & fixing 75 mm bore cast iron hubless pipe waste and vent pipe in any length with or without ears laid in trenches/floor/wall including clamps, jointing with necessary coupling complete all as specified & directed by Engr-in-charge.

S&F in repairs cast iron type hubless P trap/CPWD floor trap 75 mm bore with CP grating including jointing to waste pipe fixed with necessary coupling arrangement complete all as specified and directed by Engineer-in-charge.

S&F in repair 75mm bore cast iron hubless type door T equal/uneqal branch pieces (any radius) diminishing pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified and directed by Engineer-in-charge.

S&F in repair 75mm bore cast iron hubless type plain bends (any radius) dimining pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified and directed by Engr-in-Charge.

Supply only 75 mm bore sheilding (ss) coupling (with epdm rubber as per requirement complete all as specified and directed by Engineer-in-charge.

Supply & fixed Clamp for hanging/ fixed of 75mm/100mm hubless pipes complete all as specified and directed by Engineer-in-charge.

E/M PORTION Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces complete all as specified and directed by Engr-in-Charge.

Taking down MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed by Engr-in-Charge.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engr-in-Charge.

M&L for concealed Point wiring with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with modular sheet top cover of required module for mounting switches, sockets etc complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour for One Light point controlled by one, one way switch.complete all as specified and directed by Engr-in-Charge. .

,--ditto--- all as per Serial item No 135 above, but for One ceiling/exhaust fan point controlled by one switch and regulator complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 135 above, but forOne bell/buzzer point controlled by one bell push complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 135 above, but for One 3 pin 5 amps switch socket outlet point on same board with other switches complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 135 above, but for One 3 pin 5 amps switch socket outlet point on independent board complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 135 above, but for Two way point controlled by two way switch complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 135 above, but for wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for 15 amps power point complete all as specified and directed by Engr-in-Charge. ..

Supply and fix piano switch flush button single pole one way 5/6 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fix socket outlet 2 in 1, 2/3 pin 6 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix socket outlet 2 in 1, 3 pin 5 amp and 15 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix piano switch 15 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix piano switch flush button single pole two way 6 Amps complete all as specified and directed by Engineer-in-Charge.

S & F batton integrated LED light fitting 1 x 20 W integral sleek polycarobonate LED Channel with white acrylic cover to roof/ceiling/wall with necessary wooden/PVC blocks etc and connecting with 2 core flexible PVC insulated multistranded copper conductor from ceiling rose to fitting incl taking out old one complete all as specified and directed by Engineer-in-Charge. Note : (i) With lumen efficiency in excess of 100 lumens par watt and driver efficiency>85% (with pf>0.95) (ii) CRI>80 (iii) The warranty of LED fittings is 02 year after completion of liability period

Supply and fix lamp holder insulated body with back plate for angle/batten fitting with LED of 09 watt complete all as specified and directed by Engr-in-Charge.

Supply and fix switch piano bell push 6A flush type complete all as specified and directed by Engr-in-Charge.

Supply and fix door bell AC 230 volts single phase complete all as specified and directed by Engr-in-Charge.

Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps complete all as specified and directed by Engr-in-Charge.

S & F stepped type fan regulator electronic solid state with stepssuitable for 1200/1400mm sweep ceiling fan working on 230V AC complete all as specified and directed by Engr-in-Charge. .

Supply and fix Vertical MCB DB TPN 4 ways double door including MCCB 125 Amp 16 KA as incommer with bus bar rating 200 Amps vertical type dust and vermin proof including fixing on wooden board or recessed on wall complete all as specified and directed by Engr-in-Charge.

Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door including wooden board complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB single pole 240 volt 5-32 amps 10 KA, complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB SPN 5-32 amp, 240 volt 10KA complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB SP 40 amp, 240 volt 10KA complete all as specified and directed by Engr-in-Charge.

Supply and fixing PVC Blanking Plates one way with internal lock complete all as specified and directed by Engr-in-Charge.

Material & Labour for Sub Main Wiring with two run single core 6 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable with and including 4 Sqmm copper green colour earth wire complete all as specified and directed by Engr-in-Charge. NOTE - Two run of 6 sq.mm & One run of 4 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15mm thick and packed layer of charcoal dust and common salt, connected to earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire galvaniseed iron or steel and thimbles and other end of the earth wire connected to earthing test point and prortected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel and wire mesh, PCC chamber in cement concrete (1:2:4) type B1 and CI cover with frame all as shown in electrical plate No 3 of MES Schedule Part I of SSR 2009 complete all as specified and directed by Engr-in-Charge. Note : (i) 20mm dia GI pipe for watering to be provided with a socket and plug and should be 10cms above ground level (ii) Outer edge of earth pit will be 1 metre away from the outer edge of PCC chamber (iii) GI wire upto DBs earth connection is included in this item (iv) Water pipe shoul be provided in slanting position.

S&F sheat metal enclosure single pole and neutal with 02 Pin and earth plug and socket complete with 01 single pole 20 Amps 240volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection complete all as specified and directed by Engr-in-Charge. .

M&L for repair to door hinges of MS housing of size 0.90X0.60 m icluding necessary welding and painting the panel with two coat of synthatic enamelled paint over a coat ofred oxide primer complete all as specified and directed by Engr-in-Charge.

Supply and fix fresh air fan 230 mm sweep 240 vot 50 Hz plastic body complete with louvers and including making cavity/hole in wall, window for fixing complete all as specified and directed by Engr-in-Charge.

S&F electric water heater, storage type steel body with copper tank and heating element upto 2KW capacity 25 liter, BEE 5 star rated cpomplete with all accessoriessuch as safety valve, thermpstate, NRV, connection piece etc after dismantling old items deposit to MES store complete all as specified and directed by Engr-in-Charge.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200mm sweep, BEE 5 star rating with bushless direct current motor after dismantling old item deposit to MES store complete all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan steel body AC single Phase 230V of size 300mm sweep with blades and frames and louvers after dismantling old item deposit to MES store complete all as specified and directed by Engr-in-Charge.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

ram rattan dass aggarwal