NIT-30 of 19-20 REPAIR TO BRICK WORK, JOINERY, PAINTING, PLUMBING WORK, ROOFING, FLOORING AND OTHER MISC ITEMS IN ARMY UNITS OF PATNITOP, NATHATOP, BATOTE, RAMBAN AND BANIHAL UNDER GE (I) 873 EWS

Amount

Taking down cement plaster on bricks or stone wall/ceiling decayed surfaces of concrete from roof projection or RCC chajjas etc. including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

Rendering 15mm thick in cement mortar 1: 6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement, complete all as specified.

Demolition of cement concrete in ground floors and paving (un-reinforced) not exceeding 15cm. thickness, below or above ground level, complete and removing rubbish from the site, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

75mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection etc., finishing surface even and smooth without using extra cement including making joints with bitumastic filling in proportion of bitumen and sand 1:3 by weight complete as specified and directed. Note : The concrete shall be laid at a stretch not exceeding 3.0m in length and joint shall be made at every turning / corners, complete all as specified and directed.

40mm thick, plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in floors etc., finishing surface even and smooth without using extra cement including use and waste of formwork to divide the area into panels, complete as specified and directed.

Vitrified coloured tiles, light shade, of size 596mm x 596mm x 9 to 10mm thick as in floors etc. bedded & jointed in neat cement slurry over and including 15mm thick screed bed in CM 1:4 and pointed in coloured cement to match the colour of tile all as specified and directed.

Non-skid coloured glazed ceramic tiles of any shade and any pattern of size (Pattern consists combination of two or more tiles) 400mm x 400mm x 7mm thick, over and including 15mm thick screed bed in CM 1:4 as in floors etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Glazed ceramic coloured wall tiles in any type and in any pattern (Pattern consist of combination two or more different colour tiles etc.) in vertical surfaces of size 300mm x 200mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4, finished fair to received the tile, complete all as specified and directed.

16mm to 18mm thick of size not less than 53 x 53cm, machine cut Kota stone slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finish polishing, over and including 15mm thick screed bed or bedding layer of cement mortar 1:4 all as specified and as directed.

16mm to 18mm thick, machine cut Kota stone as in riser or steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and rounding off edges complete with mirror finish polishing, over and including 15mm thick backing coat of cement mortar 1:3 all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frames exceeding 1.50 Sqm and not exceeding 4.00 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Taking down shutter of any description, exceeding 1.00 Sqm and not exceeding 2.00 Sqm each all as specified and directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 No's of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge, complete all as specified and directed.

PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregate) as in back filling of pressed steel frames and in bed block for holdfast etc. similar work etc. complete all as specified and directed.

35mm thick 2nd class Hard wood factory made rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

35mm thick, 2nd Class hard wood, factory made, glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

Steel windows with side hung shutter including projecting type hinges, steel handle 02 Nos., steel tower bolts 100mm long and steel peg stays lugs including hold fast complete with glazing bars dovetailed or welded including locking arrangement, complete all as specified and as directed.

Steel windows with side hung shutter including projecting type hinges, steel handle 02 Nos., steel tower bolts 100mm long and steel peg stays lugs including hold fast complete without glazing bars dovetailed or welded including locking arrangement, complete all as specified and as directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified and directed.

Mild steel framed works such as grills, framed guard bars and similar work conforming to Fe- 410- O or Fe- 310- O grade, including bending, cutting and welding as required, complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified & directed.

Factory made solid panel PVC door / cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification in SSR Part-I.

Powder coated aluminium anodised frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., (minimum thickness of powder coating 50 micron), complete all as specified & directed.

Powder coated aluminium door shutter, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos on each shutter, hinges, anodised aluminium snap beading screws etc., minimum thickness of powder coating 50 microns, complete all as specified, complete all as specified & directed.

Powder coated aluminium window and ventilator shutter, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 01 Nos, peg stay 01 No, on each shutter, hinges type B-21 100mm long 02 Nos, anodised aluminium snap beading screws etc., minimum thickness of powder coating 50 microns, complete all as specified, complete all as specified & directed.

Door closer aluminium die cast body, hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Door closer aluminium die cast body, hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repairs, complete all as specified and directed.

Butt hinges, medium weight, cold rolled mild steel, 100mm size, complete all as specified and directed.

Sliding door bolts, mild steel, 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

Mild steel barrel tower bolt of stove enamelled black with bright bolt and fixed complete of size 150mm long complete all as specified and directed.

Mild steel barrel tower bolt of stove enamelled black with bright bolt and fixed complete of size 125mm long complete all as specified and directed.

Aluminium handles, cast type, anodised handles of size 150mm, complete all as specified and directed.

Floor door stopper 150mm overall length of cover plate of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, complete all as specified and directed.

Mortice lock, fancy type, 4 levers, verticle type, brass body, 100mm size, fixed in repairs, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads, complete all as specified and directed.

4mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

4mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

4.8mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

4mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square not exceeding 0.5 Sqm each complete all as specified and directed.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and aperture 1.00mm and fixed with tinned tacks or galvanized wire staple, complete all as specified and directed.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and aperture 1.00mm and fixed with tinned tacks or galvanized wire staple, fixed in repairs, complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings, complete all as specified and directed.

6mm thick Asbestos cement corrugated or semi-corrugated sheets in roofs, walls etc., fixed with L-type or J-type or cranked hook bolts, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including nanital or similar pattern from roof covering or in ridges, hips, valley gutter and similar works complete, all as specified and directed.

Galvanised, corrugated mild steel sheeting, with two corrugation side lap fixed with 'L' type or 'J' type or cranked hooked bolts with washers in roofs, 0.63mm thick, Gde-O quality, with 120grams/sqm zinc coating and Gde 'B' (i.e. 12.5 mm) corrugation complete, all as specified and as directed.

All as per the description of Serial Item No '50' here-in-before but fixing only using serviceable sheets obtained from Serial Item No '49' complete, all as specified and as directed.

0.80mm thick plain, Galvanised, mild steel sheeting (ISI marked) grade 'O' with minimum 120grams/sqm for zinc coating in ridges, hips, valley gutters, drip, and straight flashings, fixed with coach screws and washers complete, all as specified and as directed.

Pre-painted galvalume aluminium zinc coating G.I based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering, fixed with self taping screws, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating G.I based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering / cladding to wall, fixed with self taping screws, complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, PVC, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillets complete all as specified and as directed.

Arm strong mineral suspended ceiling system (FINE FISSURED (TEGULAR) EDGE TILES WITH ARMSTRONG XL 24MM EXPOSED GRID) (regular) edge tiles with armstrong. The grid should be of "Armstrong" make with 24mm wide T-section flanges colour white having rotary stitching on all T section i.e. the main runner with C3 coupling, 1200mm & 600mm cross Tees with Hardened XL2 clip and web height of 32, 27 and 25mm with a load carrying capacity of 7.05 Kgs/m. The T section have a Galvanizing of 120 grams per Sqm & passed through 72 hrs of Salt test complete all as specified.

4mm thick non asbestos fibre cement building boards laid / inserted to GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and hangers 6mm dia GI (upto 1200mm length adjusting level fixed to roof/slabs by means of ceiling cleats made out of GI flat 40mm x 30mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long and scrwed at 450mm centre to centre / intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleats and steel expansion fasteners with and including ceiling section (not exceeding 1.20 metre length) of 0.55 mm thickness having kurled web of 50mm and flanged of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457 mm centre to centre, size of grid 605mm x 605mm complete all as specified and directed.

12mm thick Perforated Particle Board / Tiles for insulation and accoustic purpose, 600mm x 600mm size, fixed with nails to timber frame work all as specified and directed.

12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work all as specified and directed.

PVC panelling made up of PVC hollow panels 25 / 30 cm in width and 10mm thickness, interlocking pattern, of approved shade and design, fixed to walls or ceilings all as per the manufacturer's instructions, fixed in repirs, complete all as specified and as directed.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

Dismantling water tanks of any description exceeding 250 litres capacity but not exceeding 500 litres, complete all as specified and directed.

Dismantling water tanks of any description exceeding 500 litres capacity but not exceeding 1000 litres, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position, including over flow and drain out pipe complete of 500 litre capacity complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position, including over flow and drain out pipe complete of 1000 litre capacity complete all as specified and directed.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed to 20mm bore dia of pipe (Minimum weight 210gms), complete all as specified and directed.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed to 20mm bore dia of pipe (Minimum weight 210gms), fixed in repairs, complete all as specified and directed.

Gun metal globe or gate valve with iron wheel heads, screwed both ends for 15mm dia bore iron pipe complete all as specified and as directed.

Gun metal globe or gate valve with iron wheel heads, screwed both ends for 20mm dia bore iron pipe complete all as specified and as directed.

PVC cover for water storage tank of capacity 500 litres / 1000 litres complete including hinging device all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 15mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 15mm dia complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 15mm dia complete all as specified and as directed.

Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, fixed in repair, complete all as specified and as directed.

Pillar taps, cast copper alloy, fancy type, swan neck, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, fixed in repair, complete all as specified and as directed.

Bib tap long body cast copper alloy CP, fancy type, with capstan Head handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule, fixed in repair, complete all as specified and directed.

Stop cock / Angle valve CP cast copper alloy, fancy type, with capstan head handle,and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, complete all as specified and directed.

Stop valve CP, cast copper alloy with crutch or butterfly handle, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, fixed in repair, complete all as specified and directed.

Brass CP Wall mixer with adjustable wall flange, for mixing hot & cold water screwed down for iron pipe of 15mm bore and fixed in repairs complete all as specified and directed.

Stop cock / Angle valve CP cast copper alloy, fancy type, concealed type, with long shank and cup, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, complete all as specified and directed.

Two way Stop cock / Angle valve, CP cast copper alloy, fancy type, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, complete all as specified and directed.

Vitreous china wash hand basin 550 x 400mm, white flat back including cast iron bracket, cutting for and pinning the ends of brackets or erecting on stand including 32mm bore brass chromium plated waste coupling with long screwed shank and fly nuts, PVC flexible waste pipe of bore 32mm and adequate length, 15mm bore PVC connection pipe 450mm long with brass nuts on both side, complete all as specified and as directed.

Vitreous china wash down water closet pan (pedestal pattern) white, including ‘P’ or ‘S’ trap, white seat cover with flat bottom and mild steel CP hinging device, CP brass jet nozzle with 1500 mm long PVC pipe, fixed in repairs, complete all as specified and directed.

Vitreous china Orissa pan of pattern, long pan size 580mm x 440mm, with ‘P’ or ‘S’ trap, front or back inlet and integral foot rest complete including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe, and anti siphon pipe, fixed in repairs complete all as specified and directed.

10 litres capacity PVC low level flushing cistern of approved make complete with PVC flush pipe and connection to water closet, fixed in repair, complete all as specified and directed.

Vitreous China urinal bowl type of size 465mm x 355mm x 265mm white with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall, securing urinal to plugs, pointing around and making connection to flushing pipe and outgoing pipe, (excluding flushing cistern, flush pipe and waste pipe), fixed in repairs, complete all as specified and directed.

Vitreous china coloured half stall urinal, flat back (Large) of size 430mm x 370mm x 340mm with C.P. flushing nozzle on top, grating and union for discharge pipe including PVC waste pipe, complete all as specified and directed.

Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, fixed in repairs, complete all as specified and directed.

Brass chromium plated shower rose 125mm with swivel joints including fixing to steel pipe or union S&F in repair, complete all as specified and directed.

PVC flexible Waste pipe 32mm dia for Wash Hand Basin, complete all as specified and as directed.

Waste coupling of PTMT 32mm bore for urinal / Sink / WHB complete all as specified and as directed.

Chromium plated Jet nozzle (Jet Spray) including 1500mm CP flexible pipe for EWC fixed all as specified and completed.

Chromium plated hand shower (health faucet) including CP flexible pipe for EWC fixed all as specified and completed. completed. Make : JAQUAR Cat Part No ALD-CHR-593 or equivalent in ESS ESS / MARC / CERA

Soap dish, vitreous china of size 160mm x 160mm x 90mm, complete all as specified & directed.

Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats (Minimum weight 190gms), complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified & directed.

Corner glass shelf with bracket, complete all as specified & directed.

PVC connection 600mm long fitted with PTMT nut and washer on both ends, fixed to 15mm bore iron pipes, complete all as specified and directed.

PVC pipes, single socketed, in any length of 110mm bore with rubber ring joints, laid in fixed to walls, complete all as specified and directed.

PVC pipes, single socketed, in any length of 75mm bore with rubber ring joints, laid in fixed to walls, complete all as specified and directed.

Grating round 140 mm dia of PTMT (with or without holes) complete all as specified & directed.

Cast iron Floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) dia of outlet 100mm, complete all as specified & directed.

Cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) dia of outlet 100mm, complete all as specified & directed.

Preparation new plastered or previously untreated surfaces of walls and applying three coats of white wash , complete all as specified and directed.

Preparation old plastered surfaces of walls including brooming down or steel wire brushing, scrapping down smoke, soot, mould, moss and efflorescent salts and treating oil and greasy spot, applying one coat of white wash, complete all as specified and directed.

Preparation old plastered surfaces of ceiling including brooming down or steel wire brushing, scrapping down smoke, soot, mould, moss and efflorescent salts and treating oil and greasy spot, applying one coat of white wash, complete all as specified and directed.

Preparation new plastered surfaces of walls and applying two coats of cement base paint including one coat of cement primer complete all as specified and directed.

Preparation old plastered surfaces of walls including brooming down or steel wire brushing, scrapping down smoke, soot, mould, moss and efflorescent salts and treating oil and greasy spotand applying one coat of cement base paint complete all as specified and directed.

Preparation old plastered surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and as directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of old wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Staining and Varnishing wood and wood based surfaces of any description over 10cm in width or girth and applying thin varnishing including preparation of old treated surfaces complete all as specified and as directed.

Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

khajuria builders

SINGH CONST CO

KUMAR CONSTRUCTION CO

Bidder Name

khajuria builders

SINGH CONST CO

KUMAR CONSTRUCTION CO

M S BANSI LAL CONSTRUCTION CO