Creation of New MDP Office and renovation of old MDP office

Creation of New MDP office

Civil Work

Providing and laying Vitrified/ GVT/ DGVT tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints. Cost of grouting are included in the rates. As per the size 600x1200 mm, shade and finish Approved by the engineer In charge/ user Department

Providing and laying Vitrified tiles Vitrified/ GVT/ DGVT in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints Cost of grouting are included in the rates. As per the size 600x1200 mm, shade and finish Approved by the engineer In charge/ user Department

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm

each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete 66mm overall thickness partition using 8mm thick double skin multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS : 14862 with suitable fibre cement screws

Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the 'W' profile (0.55 mmthick) having a knurled web of 51.55 mm and two flanges of 26 mmeach with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channelhaving one flange of 20 mm and another flange of 30 mm with thicknessof 0.55 mm and web of length 27 mm. Perimeter channel is fixed on thefloor and the ceiling with the nylon sleeves @ 610 mm C/C with fullythreaded self‐tapping dry wall screws. Board is fixed to the 'W' profilewith 25 mm countersunk ribbed head screws @ 200 mm C/C., allcomplete as per the drawing & directions of engineer‐in‐charge, thejoints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish. Multipurpose cement board reinforced with suitable fibre cement screw. 8 mm thick cement fibre board as per IS : 14862

Providing, making and fixing of Storage cabinet /wall mount cabniet /back cabniet with shelves/drawers/doors as per the design/ drawing and instructions of Engineer Incharge fabricated with Marine ply borere proof/ Resistant (for prevention from temites) conforming to Is 710 of century plywood/ Greenply/ Archid ply/ Kitply, covering up with 1 mm thck. outside Mica/ laminate and 0.8 mm thck.inside Mica/laminate of Century/ greenlam /Archid/ Surfica/Airolam with Nails, fevicols etc complete including the hardware and fittings as aprroved by Enginer-in-charge such as Handle, Telescopic hinges, Telescopic Channels, locks, magnet, towerbolt, profile lights, buffer below cabniets etc. complete. Main Framing with 19/ 18mm and rest portion with thickness as per the design/ instructions of Architect/ Enginer in charge. This also includes fixing of the profile lights, buffer below cabniets, Electrical wiring etc. Cabinets measurements will be taken in elevation i.e Length x Height only.

Providing, making and fixing of Tables with shelves/drawers/doors as per the design/ drawing and instructions of Engineer Incharge fabricated with Marine ply borere proof/ Resistant (for prevention from temites) conforming to Is 710 of century plywood/ Greenply/ Archid ply/ Kitply, covering up with 1 mm thck. outside Mica/ laminate and 0.8 mm thck. inside Mica/laminate of Century/ greenlam /Archid/ Surfica/Airolam, with Nails, fevicols etc complete including the hardware and fittings as aprroved by Enginer-in-charge such as Handle, Telescopic hinges, Telescopic Channels, locks, magnet, towerbolt, profile lights etc. complete. Main Framing with 19/ 18mm and rest portion with thickness as per the design/ instructions of Architect/ Enginer in charge. This includes making cutouts in the Table, buffer, fixing of the Electrical switch/ Socket, Desk Wire Cord Cable Grommets Hole Cover for Office PC Desk Cable Cord Organizer, cable manager, any internal wiring when required etc. Measurement of the Table will be taken in elevation i.e Length x Height only.

Providing, Fixing and Making of 09 seater conference table of size LxBXH=3.55mx1.20mx0.80m as per the design/ drawing and instructions of Engineer Incharge fabricated with Marine ply borere proof/ Resistant (for prevention from temites) conforming to Is 710 of century plywood/ Greenply/ Archid ply/ Kitply, covering up with Mica/ laminate of 1mm thickness of Century/ greenlam /Archid/ Surfica/Airolam, with Nails, fevicols etc. including all hardware and fittings. complete. Main Framing with 19/ 18mm and rest portion with thickness as per the design/ instructions of Architect/ Enginer in charge For design details drawing is attached. This includes making cutouts in the Confernce Table, buffer, fixing of the Electrical switch/ Socket, Desk Wire Cord Cable Grommets Hole Cover for Office PC Desk Cable Cord Organizer, Pop up charging box, Hiding of A.V. etc. and cutting holes for Mica etc. cables including cable manager etc. what ever required to finish the table with associated Audio video. Part ( A.V. will be done by other contractor but the civil contractor will coordinated with him to avoid any confusion and mistake) Measurement of the Conference Table will be taken in elevation i.e Length x Height only. (i.e 3.55 mx0.08m)

Providing, making and fixing of Book shelves with shelves/drawers having glass doors as per the design/ drawing and instructions of Engineer Incharge fabricated with Marine ply borere proof/ Resistant (for prevention from temites) conforming to Is 710 of century plywood/ Greenply/ Archid ply/ Kitply, covering up with 1 mm thck. outside Mica/ laminate and 0.8 mm thck. inside Mica/laminate of Century/ greenlam /Archid/ Surfica/Airolam, with Nails, fevicols etc complete including the hardware and fittings as aprroved by Enginer-in-charge such as Handle, Telescopic hinges, Telescopic Channels, locks, magnet, towerbolt, profile lights etc. complete. Main Framing with 19/ 18mm and rest portion with thickness as per the design/ instructions of Architect/ Enginer in charge. This includes fixing of the profile lights, Electrical wiring etc. Book shelf measurements will be taken in elevation i.e Length x Height only.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coat

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacture over the plastered wall surface to prepare the syrface even and smooth complete.

Providing & Fixing of Premium Self-Adhesive decorative type Waterproof Wallpaper a versatile and high-quality roll covering provides excellent protection against moisture and stains as per Aproved Design, Thickness, texture/ finish etc. including pasting it with the suitable addtional Adhesive properly complete as per design/ drawings and instructions of Engineer.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. including dash fasteners: Powder coated aluminium (minimum thickness of powder coating 50 micron) For fixed portion

Providing and fixing aluminium work for sliding doors in doors/ windows/ ventilators / partitions with extruded built up standard tubular sections/ appropriate and required sections of approved make, including rubber beading, 03 way sliding tracks, rollers, dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, interlocks, fixing labour for glass in sliding doors/windows/ventilators, lobour, material cost etc. complete job in all respect. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. including dash fasteners: Powder coated aluminium (minimum thickness of powder coating 50 micron) For sliding portion. Complete job in all respect. The aluminium section and required section should be strong enough to withstand the weight of slding door without shaking of window/door frame.

Providing & Fixing of Roman Blinds ( Blackout) made up of Approved cloth, Design, colour texture/ finish etc. as per Architects choice. Having weight of 250 GSM complete with all acessories/ fittings, fixing etc. as per the instructions of Engineer Incharge.

Foam/Thermacol sheets sandwiched between board of false wall for noise cancelation. The sheet size: 1200 X 1800, 50MM thickness.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long

dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Providing and fixing marine ply - 19mm thick ply Conforming to IS 710 and boral proof of approved brand and shade with suitable full threaded steel screws etc. in partitions, including laminate/venner and polish, whatever required to complete the job etc. complete job as per direction of Engineer-in-charge .

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick. Laminate to be fixed on existing door constructed as per Above item with proper grooves etc. as per the drawing/ design/ instructions of the Engineer Incharge.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below

Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete : 12 mm thick

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete Makes : Godrej, Harrison as approved by Engineer Incharge

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete

Providing and fixing bright finished brass/ Stainless Steel tower bolts (barrel type) as per the Approved design with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass/ Stainless Steel single/ double hanging type floor door stopper as per the Approved design with necessary screws, etc. complete.

Providing and fixing acrylic LED logo sign board in 3D concept with necessary accessories and screws etc. complete

Provding, making and fixing of 03seater sofa-01 nos. and 01seater sofa-01 nos. with wooden top handle, pine top finish polish fabricated with 40 density seat chushion of size 21"x22"and back foam of 32 density including fabric (as approved by Engineer-in-charge), making cloth, any size foam required to give required shape, nails, glue, fevicol, stepler pins,sticking of fabric, labour cost, any material as when required etc. complete in all respect. as per instructions of Engineer-in-charge.

Providing, making and fixing of centre table and corner table made up of powder coated anodize Aluminium section frame size 1.20x0.60x0.45 m. as per the design/ drawing and instructions of Engineer Incharge fabricated with Marine ply borere proof/ Resistant (for prevention from temites) conforming to Is 710 of century plywood/ Greenply/ Archid ply/ Kitply, covering up with 1 mm thck. outside Mica/ laminate and 0.8 mm thck. inside Mica/laminate of Century/ greenlam /Archid/ Surfica/Airolam, with Nails, fevicols etc complete including the hardware and fittings, Main Framing powder coated anodize Aluminium section as aprroved by Enginer-in-charge such as Handle, Telescopic hinges, Telescopic Channels, locks, magnet, towerbolt, profile lights, buffer etc. complete. Main Framing powder coated anodize Aluminium section frame size 1.20x0.60x0.45 m. as instructions of Architect/ Enginer in charge. Measurement of the Table will be taken in elevation i.e Length x Height only.

Making Cutout for Eye View in the Door

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge. For door/ window/ clerestory window

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Cold twisted bars

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

P/F of translucent / Frosted/ Opaque dark film as approved (Glass ware make or equivalent) on glass/ventilators/window etc. complete in design/pattern as per the suggested design including cutting for strips etc. However, the measurement for such strips cut out will also be taken all work completed to the satisfaction of Engineer-in charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Electrical works for Creation of new MDP office

SUB HEAD {I):- INTERNAL WIRING

Point wiring in PVC conduit, with piano type switch :-

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit, with mdular type switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Twin Control Point wiring in PVC conduit, with piano type switch :-

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, 2 way piano type switch, phenolic laminated sheet, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Power plug wiring in PVC conduit (2 x 4 Sq.Mm.):-

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Power plug wiring in PVC conduit (4 x 4 Sq.Mm.):-

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Circuit/ Sub main wiring in PVC conduit:-

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.

2 X 1.5 sq. mm+ 1 X 1.5 sq. mm earth wire.

2 X 2.5 sq. mm+ 1 X 2.5 sq. mm earth wire.

Supplying and fixing metal box of 150 mm X 75 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required.

Supplying and fixing metal box of 180 mm X 100 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 A & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2 poles and earth metal enclosed plug top along with 20 amps. "C" curve, SP MCB in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required.

S/F modular type electronic fan regulator:-

Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F modular type blanking plate :-

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supply and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required:

SUB HEAD (II):- MCB's

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts 'C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole

Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

S/F DP MCB Isolator

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following rating, four pole, (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensivity current upto 300 miliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required:

SUB HEAD (IV):- MISCELLANEOUS

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing Cat 6e 100 Meter Ethernet Cable/LAN Cable/Network Cable I High Speed 250MHZ I Weatherproof/UV Resistant I RJ45 Lan Cable I -10° To 60° Weather I Solid Conductor.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. As required.

5/6 A switch

3 pin 5/6 A socket outlet

TV antenna socket outlet

Bell push

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

SUB HEAD(V):-INTERNAL LIGHTING FIXTURES & FANS

Installation, testing and commissioning of pre-wired, flourescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection with 1.5 sq. mm. FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supply, Installation, Testing and Commissioning of Crompton SilentPro Blossom 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply, Installation, Testing and Commissioning of Crompton high flo waveplus 400mm wall mount fan with copper wire winding motor suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

SUPPLY OF LIGHTING FIXTURES

Supply and fixing of Philips Twin Glow LED Downlighter 15W having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect.

Supply and fixing of Profile light Fitting for false Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. 320-520 system lumens with fully covered diffuser type >120 Lm/W, PF>0.95, THD< 10% at full load CRI >80, > 300 V over voltage Protection 4 KV internal Surge Protection with (5 Year Warrenty)

Supply & installation of Split Direct Expansion Air Conditioners Suitable for operation on A/C supply single phase 50HZ 230 Volts with hermetically sealed compressor with air cooled condenser, motor capacitor and start run capacitor, relay and over load protector internal unit, with one indoor and one outdoor unit. The condenser unit will be placed outside the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube. (High Wall Chorded/ Cordless) Suitable Capacity 3 Core sheathed/ PVC copper cable and a battery operated wireless remote unit. BEE 5STAR EER 3.4 (2.0 TR) inverter AC

Renovation of old MDP Office

Civil work for Renovation of old MDP office

Providing & Fixing of Roman Blinds ( Blackout) made up of Approved cloth, Design, colour texture/ finish etc. as per Architects choice. Having weight of 250 GSM complete with all acessories/ fittings, fixing etc. as per the instructions of Engineer Incharge.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm

and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing ISI marked 19 mm thick door shutters for trap door including wooden frame work in false ceiling, tie rods, hanging arrangements, fastener etc. what ever required to fix the trsp door shutters fabricated withmarine ply borer proof/resitant conforming to IS 710 of centrury plywood/Green ply/ Archid ply, Kitply. Complete job in all respect.

Providing, making and fixing of Tables with shelves/drawers/doors as per the design/ drawing and instructions of Engineer Incharge fabricated with Marine ply borere proof/ Resistant (for prevention from temites) conforming to Is 710 of century plywood/ Greenply/ Archid ply/ Kitply, covering up with 1 mm thck. outside Mica/ laminate and 0.8 mm thck. inside Mica/laminate of Century/ greenlam /Archid/ Surfica/Airolam, with Nails, fevicols etc complete including the hardware and fittings as aprroved by Enginer-in-charge such as Handle, Telescopic hinges, Telescopic Channels, locks, magnet, towerbolt, profile lights etc. complete. Main Framing with 19/ 18mm and rest portion with thickness as per the design/ instructions of Architect/ Enginer in charge. This includes making cutouts in the Table, buffer, fixing of the Electrical switch/ Socket, Desk Wire Cord Cable Grommets Hole Cover for Office PC Desk Cable Cord Organizer, cable manager, any internal wiring when required etc. Measurement of the Table will be taken in elevation i.e Length x Height only.

Providing, making and fixing of Storage cabinet /wall mount cabniet /back cabniet/bookshelf with shelves/drawers/doors as per the design/ drawing and instructions of Engineer Incharge fabricated with Marine ply borere proof/ Resistant (for prevention from temites) conforming to Is 710 of century plywood/ Greenply/ Archid ply/ Kitply, covering up with 1 mm thck. outside Mica/ laminate and 0.8 mm thck.inside Mica/laminate of Century/ greenlam /Archid/ Surfica/Airolam with Nails, fevicols etc complete including the hardware and fittings as aprroved by Enginer-in-charge such as Handle, Telescopic hinges, Telescopic Channels, locks, magnet, towerbolt, profile lights, buffer below cabniets etc. complete. Main Framing with 19/ 18mm and rest portion with thickness as per the design/ instructions of Architect/ Enginer in charge. This also includes fixing of the profile lights, buffer below cabniets, Electrical wiring, Profile lights etc. Cabinets measurements will be taken in elevation i.e Length x Height only.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coat

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacture over the plastered wall surface to prepare the syrface even and smooth complete.

Providing & Fixing of Premium Self-Adhesive decorative type Waterproof Wallpaper a versatile and high-quality roll covering provides excellent protection against moisture and stains as per Aproved Design, Thickness, texture/ finish etc. including pasting it with the suitable addtional Adhesive properly complete as per design/ drawings and instructions of Engineer.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. including dash fasteners: Powder coated aluminium (minimum thickness of powder coating 50 micron) For fixed portion

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of enginee rin-charge Pre-laminated particle board with decorative lamination on both sides as per Approved design, Shade , colour etc.

Providing and laying Vitrified tiles/ GVT/DGVT in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints. Cost of grouting are included in the rates. 600x600 mm size, As per the shade and finish Approved by the engineer In charge/ user Department

Providing and laying Vitrified tiles/ GVT/DGVT in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints Cost of grouting are included in the rates. . 600x600 mm size, As per the shade and finish Approved by the engineer In charge/ user Department

Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the 'W' profile (0.55 mmthick) having a knurled web of 51.55 mm and two flanges of 26 mmeach with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channelhaving one flange of 20 mm and another flange of 30 mm with thicknessof 0.55 mm and web of length 27 mm. Perimeter channel is fixed on thefloor and the ceiling with the nylon sleeves @ 610 mm C/C with fullythreaded self‐tapping dry wall screws. Board is fixed to the 'W' profilewith 25 mm countersunk ribbed head screws @ 200 mm C/C., allcomplete as per the drawing & directions of engineer‐in‐charge, thejoints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish. Multipurpose cement board reinforced with suitable fibre cement screw. 8 mm thick cement fibre board as per IS : 14862

Refurbishment of exisiting 03 seater sofa-01 nos., 02seater sofa-04 nos. and 01seater sofa-02 nos. changing of upholestry, polishing of sofa, repalcement of damaged 40 density seat chushion of size 21"x22"(13 nos.)and back foam of 32 density (13 nos.) including fabric (as approved by Engineer-in-charge), making cloth, any size foam required to give required shape, nails, glue, fevicol, stepler pins,sticking of fabric, labour cost, any material as when required etc. complete in all respect. as per instructions of Engineer-in-charge.

Dismantling wooden boardings / PVC boarding in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : Up to 10 mm thick

P/F of PVC wall Cladding of required shade and size same as existing installed in old MDP office with nails, screws,corner beading, U shape beading, supporting members, including labour cost, material cost etc. whatever required to complete the job damaged due to creation of electrical points.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Providing and fixing marine ply - 19mm thick ply Conforming to IS 710 and boral proof of approved brand and shade with suitable full threaded steel screws etc. in partitions, including laminate/venner and polish, whatevere required to complete the job etc. complete job as per direction of Engineer-in-charge .

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Electrical work for old MDP Office

SUB HEAD {I):- INTERNAL WIRING

Point wiring in PVC conduit, with piano type switch :-

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with mdular type switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Twin Control Point wiring in PVC conduit, with piano type switch :-

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, 2 way piano type switch, phenolic laminated sheet, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Power plug wiring in PVC conduit (2 x 4 Sq.Mm.):-

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Power plug wiring in PVC conduit (4 x 4 Sq.Mm.):-

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Circuit/ Sub main wiring in PVC conduit:-

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.

2 X 1.5 sq. mm+ 1 X 1.5 sq. mm earth wire.

2 X 2.5 sq. mm+ 1 X 2.5 sq. mm earth wire.

Supplying and fixing metal box of 150 mm X 75 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required.

S/F power plug point piano type accessories:-

Supplying and fixing metal box of 180 mm X 100 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 A & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2 poles and earth metal enclosed plug top along with 20 amps. "C" curve, SP MCB in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required.

S/F modular type electronic fan regulator:-

Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F modular type blanking plate :-

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supply and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required:

SUB HEAD (II):- DISTRIBUTION BOARDS & MCB's

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts 'C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole

Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

S/F DP MCB Isolator

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following rating, four pole, (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensivity current upto 300 miliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required:

Supplying and fixing following way, SP&N, sheet steel, MCB distribution board, 240 Von surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator)

2+4 WAY/6 way, Double door

Supplying and fixing following way, horizontal type TP&N, sheet steel MCB distribution board, 415 Von surface /recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

4 way (4 + 12), Double door

SUB HEAD (IV):- MISCELLANEOUS

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing Cat 6e 100 Meter Ethernet Cable/LAN Cable/Network Cable I High Speed 250MHZ I Weatherproof/UV Resistant I RJ45 Lan Cable I -10° To 60° Weather I Solid Conductor.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections butexcluding modular plate etc. As required.

5/6 A switch

3 pin 5/6 A socket outlet

TV antenna socket outlet

Bell push

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

SUB HEAD(V):-INTERNAL LIGHTING FIXTURES & FANS

Supply, Installation, Testing and Commissioning of Crompton SilentPro Blossom 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

SUPPLY OF LIGHTING FIXTURES

Supply and fixing of Philips Twin Glow LED Downlighter 15W having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect.

Supply and fixing of Profile light Fitting for false Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. 320-520 system lumens with fully covered diffuser type >120 Lm/W, PF>0.95, THD< 10% at full load CRI >80, > 300 V over voltage Protection 4 KV internal Surge Protection with (5 Year Warrenty)

Please Enable Macros to View BoQ information