SPECIAL REPAIR TO BUILDING NO 92 (FLIGHT CADETS MESS) AT AF STN BEGUMPET UNDER GE (AF) HAKIMPET

Amount

SCHEDULE 'A' PART - I (B&R PORTION) :- Dismantling AC/Steel Plain or corrugatd sheet, any gauge, thickness, including Nainital with Single layer Mangalore patttern or similar pattern roof covering complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed struss complete in all respect complete all as specified and as directed.

Dismantling cast iron work of any description complete all as specified and as directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding and Ridge to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates (Fe 410-W Gde-E-250 quality-A) complete all as specified and as directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as specified and as directed.

M&L Preparing new steel Surfaces of any any description over 10cm width or girth and appling two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Demolition of cement concrete in roofs, floors (other than ground floors), etc. (unreinforced) including old tarfelt & cement mortor bedding and plastering etc complete all as specified and directed.

M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed.

M & L cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) as in roof kerbs, bands etc complete all as specified and as directed.

M & L 25 mm thick plain cement concrete (1:2:4) type B0 using 12.5mm graded agg as in levelling/padding course on roof slab for water proofing treatment complete all as specified and as directed.

M & L rendering 10mm thick on concrete surface in CM 1:4 and finishing even and smooth without using extra cement with using WPC @ 3% by wt. of cement, complete all as specified and as directed. Note:- WPC will be measured and paid separately

Supply only water proofing compound complete all as specified and as directed.

M & L for cleaning the roof surface and applying oil bond bitumen primer @ 0.2 kg/sqm providing and laying 3mm thick APP modified water proofing membrane weight not less than 4kg/sqm reinforced with non woven polyester mat weighing not less than 160 gm/sqm having soften point not less than 140 degree centigrade tensile strength not less than 800 N/sqcm tearing strength 180N with minimum of 10cm side laps and 15cm end laps by application of torch applying a coat of blown grade hot bitumen over the membrane @ 1.2kg/sqm and providing garnish with solar reflective bitumen aluminium paint @ 0.1 kg/sqm over completed area of membrane complete all as specified and as directed by engineer in charge. Note: the quoted rate shall included for cutting grooves in roof parapets, upward facias, etc and inserting of membrane and making good with CM 1:3 wherever required complete all as specified and as directed.

Demolition Wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness, including cover fillets/frame/hangers etc complete all as specified and as directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

S&F for fixing 12mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface with sunk or raised moulding or over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified and as directed.

M&L for preparation of new plastered/ceiling surface and applying two coat of distemper complete all as specified and as directed.

S&F 600x600mm GI bottom pre coated exposed snap grid frame work with 25x25x7mm wall angle and 25mm web, 35mm flange 0.7mm thick T-sections hanging with 4mm dia GI wire (up to 1200 mm long) including level clip, soffit cleat and 12.7 mm dia metal Raw plug at 1200mm c/c in both direction complete all as specified and as directed

S&F PVC laminated designed (one side PVC lamination and other side aluminium paper) gypsum board 600 X 600 X 8 mm thick tiles decorative type in GI grid frame work with screws or clips etc complete all as specified and as directed.

Demolition of cement concrete not exc.15 cm thickness in ground/1st floors including floor tile complete including removal of debries to a distance exc. 150 m and not.exc. 200 complete all as specified and as directed.

M&L 25 mm thick cement concrete 1 : 2 : 4 type B-1 (using 20mm graded crushed stone aggregate) laid in base, cement concrete surface even and smooth w/o using extra cement complete all as specified and as directed.

M&L for 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and as directed..

M&L for Vitrified ceramic coloured /printed tiles double charged of area exc 0.42 sqm and n.exc 0.1.00 Sqm, 10 mm thick, in floors/skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles complete all as specified and as directed. (Screed bed shall be measured and paid for separately)

M&L for 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms, floor, stair case and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified and as directed. (Screed bed shall be measured and paid for separately)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado / Skirting complete all as specified and as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall), window cill 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and as directed.

Rounding to edge of stone slab one edge, such on in stop, cooking plateform, and other similar situation complete all as specified and as directed.

Taking down cement or cement lime plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and as directed.

M & L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 complete all as specified and as directed.

M&L for Preparing New surfaces on wall (Upto plaster surface) and preparing the surfaces and applying two coats of oil bound distemper over a coat of Alkali resistant Primer on 3 mm thick wall care putty, complete all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

M&L for complete removal of existing treatment on wall (Upto plaster surface) and preparing the surfaces and applying two coats of oil bound distemper over a coat of Alkali resistant Primer on 3 mm thick wall care putty, complete all as specified and as directed.

M&L for preparation of existing old painted surfaces of walls and applying one coat of cement based paint,complete all as specified and as directed.

M&L for preparing old painted steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for preparation of previously treated wood or wood based surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed.

M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. complete all as specified and as directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

M&L Of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed.

M&L At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and as directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and as directed. (Glass or wiremesh shall be paid separately) Note:- For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

M&L Disconnecting existing tanks, exc 500ltr and n.exc 1000ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc) complete all as specified and as directed.

S & F 500 Ltrs capacity Rotational moulded, polythene water storage tanks incl suitable nipple( cylindrical shape with vertical top closed) hoisted and fixed in position including taking down old unserviseable water tanks complete all as specified and as directed.

All as per item No 48 herein above but capacity of 1000 ltrs -ditto-complete all as specified and as directed.

S&F in repairs 20 mm bore dia ball valves, high pressure of PTMT with epoxy coated aluminium rod & high dencity plasstic ball screwed for iron pipe and fixed .(minimum weight 15 mm-142gms / 20mm-210gms) complete all as specified and as directed.

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore pipe complete all as specified and as directed.

M&L Resecuring or easing & adjusting, without taking down shutters (Per Leaf) of any description exceeding 2 Sqm each complete all as specified and as directed.

M&L Resecuring or easing & adjusting, without taking down shutters (Per Leaf) of any description exceeding 1 Sqm but n exc 2.0 sqm each complete all as specified and as directed.

Hacking out old broken of glaass from wooden frame or stone concrete or brick with putty or fixed with nail complete all as specified and as directed.

Supply and fix sheet glass, ordinary quality, 4 mm thick, in squares not exc 0.50 Sqm in each pane and glazing with oil putty/wooden bedding complete all as specified and as directed.

Taking down chowkats or frames not exc. 1.5 Sq mtr each with shutters without taking off shutters from the frames complete all as specified and as directed.

Supply and fix solid PVC door frame of size 50 mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification complete all as specified and as directed.

Supply and fix 30 mm thick factory made PVC rigid frame panel door shutter made from MS tubular frame of gauge 19 x 19 mm style and 15 mm x 15 mm top and bottom rails MS frame to be covered with 5 mm thick heat moulded PVC 'C' channel of size 50mm x 30mm for stiles with 5mm thick PVC sheet (50 mm wide for top rail, 75 mm wide for lock rail and bottom rail on either side). Paneling of 5 mm thick PVC sheet to be fitted in the MS frame, sealed to the styles and rails with 25 mm thick PVC sheet beading on either side and joined together with cement solvent adhesive complete all as specified and as directed.

Supply and fix 100 mm size medium weight cold rolled mild steel butt hinges complete all as specified and as directed.

Supply and fix 200 mm size Alluminium, anodised barrel tower bolts of extruted section and fixed complete all as specified and as directed.

Supply and fix 150 mm size extruded aluminium door handles fabricated type fixed in repairs complete all as specified and as directed by the Engineer-in-Charge.

M&L for powder coated aluminium frame for doors, windows (fixed/ sliding), ventilators with one or more rebates including joining cleat for fixing etc. including Powder Coating (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S&F powder coated aluminium window shutters powder coating of any colour (Thickness or powder coating not less than 50 micron)., sliding type three track, two for fixing glass sections and one shutter with wire mesh aluminium section weighing 0.55 kg/Rm including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles and locking arrangement including Anodised aluminium grill ( anodised transparete or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless teel screws@ 200mm centere to centre, including cutting the grill to proper opening size for fixing and operation of handle and fixing approved anodised aluminium standard section around the opening complete all as specified and as directed. Note : Glass and Wire cloth will be measured and paid seperately under relevant item.

M&L for Sheet glass, 5.5mm thick ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and as directed.

M&L for 12mm thick plywood, grade BWR, type BB, fixed complete all as specified and as directed.

M&L for Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Supply and fix vitreous china ware wash hand basin 550mm x 400 mm size flat back or angle including new bracket and making good all connections in repairs complete all as directed by the Engr-in-Charge.

S&F 32mm Dia PVC waste pipe for sinks or wash basines etc,. in repairs complete all as specified and as directed by the Engr-in-Charge.

Supply and fix 32 mm dia bore waste fittings brass chromium plated fixed to wash hand basin/urinals with long screwed shanks and fly nuts flange and bedded in run lead cement and other end fixed in repairs complete all as directed by the Engr-in-Charge.

S&F Bib taps, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm dia and fixed complete all as specified and as directed.

S&F angle valves, cast copper alloy, chromium plated crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair.(15mm bore). complete all as specified and as directed.

Supply and fix 15 mm bore LDPE pipe 45cm long with brass nuts and washers on both ends all as in repairs complete all as specified and as directed.

M&L for unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenches complete all as specified and as directed.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply and fix Pillar taps 15mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, fancy type with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fix vitreous china wash down water closet pan (Pedestal type), western white including removing the existing one complete and making good all connections as in repairs complete all as specified and as directed.

S&F in repairs white /black plastic seat cover solid confirming to ISI any type complete all as specified and as directed.

Supply and fix 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete as in repairs all as specified and as directed.

S&F Towel Rail 600mm long 20mm dia,D type cromium plated, fixed with and including Chromium plated brass screws and wooden/plastic cleats. and fixed in repairs complete all as specified and as directed.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) and fixed in repairs complete all as specified and as directed.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) and fixed in repairs complete all as specified and as directed.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) and fixed in repairs complete all as specified and as directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed. Make : JAGUAR or equivalent in Hindware / Cera

S&F CP 2 way bib cock complete all as specified and as directed. Make : JAGUAR Cat No 38041 or equivalent in Hindware / Cera

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S & F Second class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 13 and not exceeding 25 Sq. cm complete all as specified and as directed.

S&F of 18mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on only one face; fixed with screws complete all as specified and as directed.

Extra over rates of block board or veneered particle board or plywood for external teak wood lipping, 6mm thick fixed with nails 18 mm thick complete all as specified and as directed.

M&L for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

S&F of 75 mm Brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed.

S&F of 100 mm long chromium plated brass handles fancy type complete all as specified and as directed.

S&F of Cup board lock brass 4 levers complete all as specified and as directed.

S&F of Stainless steel auto closing cup-board hinges complete all as specified and as directed.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete incomplete all as specified and as directed.

M & Labour for 25mm dia Stainless Steel Curtain Rod fancy type complete all as specified and as directed.

M & Labour in repair for Brackets, Ends Cap and Holder suitable for 25mm dia Stainless Steel Curtain Rod fancy type complete all as specified and as directed.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F, 35mm thick, 2nd class hardwood glazed & skelton shutters, open rebated & prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I section 8 clause 8.20 (a) complete all as specified and as directed.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150mm long Extruded aluminium alloy handles, fabricated type, anodised. complete all as specified and as directed.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges. complete all as specified and as directed.

Demolition of cement concrete (unreinforced and including tiles) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 75mm Cement concrete Type C-2 1:3:6 (40mm graded aggregate) for plinth protection complete all as specified and as directed.

M&L for 20 mm thick screed bed or bedding layer in CM 1:6 for laying of floor finish complete all as specified and as directed.

M&L Colour Chequired cement concrete tiles 20 cm x 20 cm x 25 mm thick with grey pigment cement and pigmenst set ionted and pointed in neat cement slurry colour to match in floors. complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section incl trusses in any position as in unframed work, complete all as specified and as directed.

Taking down or down steel tubing and connections 15 mm bore, including cleaning for refixing or removal to store complete all as specified and as directed.

All as per item No 109 above here in before but 20 mm bore -ditto- complete all as specified and as directed.

Supplying and laying 16mm of CPVC pipes SDR11 & Plain CPVC SDR 11 fitting on walls/ceiling or laying in floors complete all as specified and as directed.

All same as per item No 111 above here in before but 20 mm bore -ditto- complete all as specified and as directed.

Demolition and breaking up drain pipes(salt glazed ware, AC or reinforced concrete) set in cement motar including concrete beddeing and haunching complete all as specified and directed 100mm internal dia pipe complete all as specified and as directed.

M&L for Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 for 100mm dia pipecomplete all as specified and as directed.

M&L for SWG drain pipe grade `A` of 100mm internal dia laid in trenches and jointed in cement mortar 1:1 complete all as specified and as directed.

SCHEDULE 'A' PART - II (E&M PORTION) :- Taking down carefully copper/ aluminium point wiring (light, fan,socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good disturbed surfaces of walls, floors etc. complete all as specified and as directed by the Engineer-in-charge.

Taking down carefully MCB DB SPN/TPN, Metal P&S alongwith MCBs complete and taking credit complete all as specified and as directed by the Engineer-in-charge.

M& L for point wiring complete with 1.5 sq mm single core PVC insulated FRLS cable, with multi standard copper conductors, 1100 volts grade, including suitable size PVC conduit (concealed) and including provisoin of 1.5 sq mm PVC insulated copper cable FRLS as earth continiuty conductor, metal flush box concealed in walls and hylum sheet of suitable module and for fixing switches /sockets/ regulators etc.complete all as specified and as directed for :-

One light point controlled by one way switch .

One ceiling fan/ exhaut fan point controlled by one way switch.

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin switch socket outlet 5 Amps independent

All as per item No 118 here-in-before but with 2.5 Sq mm for 3 pin 5/ 15 Amps socket point controlled by one switch but below the switch board of light points or in the same vertical plane and 2.5 Sq mm copper conductor green in colour as earth continuity conductor complete all as specified and as directed.

All as per item No 119 above here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor complete all as specified and as directed.

S&F Switch Piano, flush type single pole, one way 5 Amps.

S&F Socket outlet 2 in 1, 3 pin, 6A flush type

S&F Switch socket combination, 2 in 1, 3 Pin, flush type 5 Amps.

S&F switch socket combination, 2 in 1, 5 Pin, flush type 5&15 Amps.

S&F stepped type electronic fan regulator flush type complete all as specified and as directed.

S&F ceiling rose 3 terminal PVC/Polycarbonate insulated body complete all as specified and as directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket (AC Box) complete with one MCB SP 20A single pole MCB complete concealed in walls complete all as specified and as directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed. by Engineer in Charge

Supply and fixing round/square shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing Flexible led strips of unit length of 5 Mtr long with Constant Voltage 24V, 2A Driver suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. Make: Havells / CG / Philips / Bajaj or as approved by GE

Supply and fixing LED luminaire 18 watt, Surface mounted LED round light fiting with pressure die-cast aluminium luminaire in powder coated white finish in round profile including connecting up with fitting suitable flexible copper conductor of suitable size complete all as specified and as directed by Engineer in Charge. Make : Havells / CG / Philips / Bajaj or as approved by GE

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative batten type with driver, holder LED tube light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make: Havells / CG / Philips / Bajaj or as approved by GE

Supply and fixing LED lights fitting 1x 10W, 220V, AC decorative batten type with driver, holder LED tube light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make: Havells/CG/Philips/Bajaj or as approved by GE

Supply and fixing Decorative, wall mounting, brushed nickel finish fixture with opal glass diffuser suitable with and including 9 W LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make: Havells/CG/Philips/Bajaj or as approved by GE

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Fixing only Sun light / chandelier including suitable hanging arrangement and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Fixing only wall mount spot/ focus light complete all as specified and as directed.

Taking down existing ceiling fan/ Exhaust fan from it's position and re-fixing the same after cleaning the dust and connecting up including provision of cable from ceiling rose/ connector to fan complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and self closing & opening louvers complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380 mm sweep with, blades, and frame and self closing & opening louvers complete all as specified and as directed.

Supply and fix wall fan of sweep 300 mm complete all as specified and as directed.

Providing suitable hole in brick /stone masonary or any type of wall for exhaust fan of upto 300 mm sweep and repair to the wall to give smooth finish as existing to the disturbed surface of wall complete all as specified and as directed.

S&F electrically Operated Chimney Single phase 230 Volt for Modular Kitchen, Faber 90cm 1200Mcub/hr Heat Auto clean Chimney suitable for Kitchen of size 8100mm x 5000mm and height 3500mm complete all as specified and as directed.

Supply & fix vertical mounted MCCB (Moulded Case Circuit Breaker) DB TPN 4 way of IP 43 protection double door with insulated bus bar assembly, neutral bar complete all as specified and as directed. Note: Incomer MCCB & outgoing MCBs will be measured and paid seperately. Make : Legrand / Indo Asian/ABB/Havells/L&T

Supply & fix MCB DB SPN 12 way double door with neutral bar etc complete all as specified and as directed. Note: Incomer & outgoing MCBs will be measured and paid seperately

Supply & fix MCB DB SPN 4 way double door with neutral bar etc complete all as specified and as directed. Note: Incomer & outgoing MCBs will be measured and paid seperately

Supply & fix MCCB (Moulded Case Circuit Breaker) upto 63 Amps, 16KA, 3 pole, 415V suitable for complete all as specified and as directed.

Supply & fix MCB SPN 40 AMP, 10KA, C Curve, 240V complete all as specified and as directed.

Supply & fix MCB SP 6-32 Amps, 10KA, C Curve, 240V complete all as specified and as directed.

M&L for Sub main wiring complete with two runs of 4 Sq mm Single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with One run of 4 Sq mm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including suitable size of PVC conduit and accessories complete all as specified and as directed.

M&L for Sub main wiring complete with two runs of 10 Sq mm Single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with One run of 10 Sq mm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through existing PVC Conduit including taking down old u/s sub main wiring complete all as specified and as directed.

Cutting chases in stone masonry wall/concrete floor/roof for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 10cm girth complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 600mmx 600mm x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25mtr below ground with top edge of the earth plate not less than 1.5 mtr below normal gound level, earth plate shall be connected with double bolts, nuts, check nuts & washers, to & including 4 mm galvanised iron wire as earth lead, extended upto 7.5 m or upto test terminal point, drawn through 40mm dia med grade GI Pipe for protection of galvanised iron strip in the ground further connecting with GI wire 4mm dia to Distribution board, including excavation, earth work, charcoal, Magnesium sulphate 50 Kg, Bentonite 25 Kg, PCC Chamber, RCC Cover slab, watering pipe 20mm dia bore med grade wire net, funnel etc & testing on completion all as specified in plate No 3 of SSR Pt-I including taking down old u/s earthing complete all as specified and as directed.

NEWS CONSTRUCTIONS (BID ID -3139130)

harshraj and co (BID ID -3131027)

MAHIRA ENGINEERING & INFRASTRUCTURE (BID ID -3130838)

RAJU AND COMPANY (BID ID -3137902)

STANDARD AGENCIES (BID ID -3138183)