Special repair to toilet of OTM Accn No. P-157 and P-161 in OTM Accn at New Mil Stn Kapurthala under GE Kapurthala

Amount

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Material & labour for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 metre built in cement mortar (1:4) complete all as specified and directed.

Material & labour for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster on brick work or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed..

Material & labour for 15mm thick cement plaster in cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified.

Material & labour for 15mm thick cement plaster in cement mortar (1:4) on brick or concrete surfaces finished even and fair without using extra cement complete all as specified.

Material & labour for 5mm thick cement plaster in cement mortar (1:3) on fair faces of concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified.

Dismantling floor, hearth or wall tiling/ china mosaic including cement mortar bedding (but not backing), removing rubbish off outside MD land complete all as specified and directed.

Material & labour for coloured ceramic non skid tiles 7 to 8mm thick, as approved, polished of size not less than 300mmx300mm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including screed bed 15mm thick in cement mortar (1:6) complete all as specified and directed.

Material & labour for glazed ceramic coloured tiles of size not less than 300 x 200 x 7mm thick as in vertical surfaces i.e. skirting/ dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface laid over and including 15mm thick rendering in cement mortar (1:4) complete all as specified and directed.

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC type E2, 1:5:10 (using 40mm graded stone aggregate as in foundation mass concrete complete all as specified and directed.

M&L for 50mm thick PCC type B-1, 1:2:4 (20mm graded aggregate as in plinth protection finished even and snooth etc complete all as specified and directed.

S&F in repair bib tap 15mm bore dia of pipe of approved colour, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule etc complete all as specified and directed.

Supply & fix in repairs 15mm bore stop cock standard of cast copper alloy of approved colour, screwed down with high pressure for both ends of iron pipe or for brass ferrule or to GI socket (min weight 110 gm) complete all as specified and directed.

Supply & fix in repairs 15mm bore pillar taps standard of cast copper alloy of approved colour, screwed down with high pressure for both ends of iron pipe or for brass ferrule or to GI socket ( Min wt 110gm) complete all as specified and directed.

Supply & fix in repair 15mm dia angle stop valve standard of cast copper alloy of approved colour, screwed down with high pressure for both ends of iron pipe or for brass ferrule or to GI socket (min wt 90 gm) complete all as specified and directed.

Supply & fix in repairs squatting pan WC Orissa pattern size 580mm x 440mm white with integral foot rest (excluding flushing cistern) with P or S trap including provision of lime concrete bedding including breaking up existing damaged WC seat and connecting flush pipe etc making good to match with existing surfaces complete all as specified and directed.

S&F in repair wash down water closet pan (pedestal pattern), white including white PVC seat cover (excluding fixing bolts, flushing cistern and flush pipe) etc complete all as specified and directed.

Supply and fixing in repair PVC valve less white low level flushing cistern 10 ltr capacity with all fittings syphonic action with top push type button with inlet ball valve and float including flush pipe, ball valve, handle, bracket of MS angle of size 25mmx25mmx3mm, 30 cm long in PCC 1:2:4 type B-1, block of size 10cmx10cmx10cm. complete all as specified and directed.

S&F in repair Vitreous China bowl urinal angle back, of size of 430 x 370 x 340 mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed by engr-in-charge.

S&F in repair vitreous china wash basin with pedestal, white, flat back, size 550x400 mm including 15mm dia pillar tap chromium plated fancy type, including 15mm dia stop cock fancy type chromium plated, CP waste coupling, waste fittings, union and waste pipe 32 mm dia or required length and all necessary inlet, outlet connections complete all as specified and directed.

Supply & fix in repairs towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified and directed.Taking up or down 15mm dia bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Supply & fix PVC connection, 15mm bore size with PTMT nuts of length 450mm and pvc washers at both ends complete all as specified and directed.

Supply & fix in repairs brass chromium plated shower rose 125 mm size with or without swivel joint any size including fixinf to steel pipe or union complete all as specified and directed.

Dismantling of 500 litre water tanks and removing to store complete all as specified and directed. .

Supply & fix in repairs rotational moulded polythene water storage tank double layer, ISI Marked of capacity 500 litre cylindrical vertical with closed top hoisted in position including supply and fix 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fitting and including complete including dismantling of existing tank of any description, capacity complete all as specified and directed.

Disconnectiong existing 500 litre capacity PVC overhead tank for repair, cleaning etc and hoisting if required, reconnecting and re fixing in position.

Taking up or down 15mm dia bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

S&F steel tubing 15 mm bore 'medium grade', galvanised, with all fitting and fixed complete to walls and ceiling or laid in trenches or floor etc complete all as specified and directed.

Refixing old steel tubing bore of pipe 15mm dia and connections in new or old position (Walls, ceiling, floors etc) complete all as specified and directed.

Taking up or down 20mm dia bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

S&F steel tubing 20 mm bore 'medium grade', galvanised, with all fitting and fixed complete to walls and ceiling or laid in trenches or floor etc complete all as specified and

Refixing old steel tubing bore of pipe 20mm dia and connections in new or old position (Walls, ceiling, floors etc) complete all as specified and directed.

S&F in repair 20mm dia ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair 20 mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area n exc. 1.5 Sqm each for doors and windows complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area exc. 1.5 Sqm but not exc 4 sqm each for doors and windows complete all as specified and directed.

Taking down shutters only of any description area not exc 1 Sqm complete all as specified and directed.

Taking down shutters only of any description area exc 1 Sqm but n. exc 2 sqm each complete all as specified and directed.

Supply & fix Steel windows/ventilator 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mm x 25mm single rebated comprises of glazed skeleton shutter ERW Sec 50mmx20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box type ‘T’ section of size 60mmx25mm and 1.25mm thick including cuttings holes and making good dismantled portion in PCC (1:3:6) type B1 using 20mm graded stone aggregate. Four Nos for each window including following fittings welded to framed shutter :- (a) Mild steel holdfasts 150mm long 12mmx3mm made to shape per window -04 Nos, (b) Handle of Z Sec 20mmx25mm, 100mm long per leaf-01 No, (c) Stopper per leaf -01 Nos, (d) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges per leaf -01 No, (e) MS pintle hinges of size 75mmx75mmx12mm per leaf -02 Nos, (f) Grills made out of MS square bar 12 mm dia welded to FI frame complete all as specified in drawing No CEJZ/TD/1019, Sh 1/3 to 3/3 and No. CEJZ/TD/1020, Sh 1/3 to 3/3. Note : (i) Fabrication shall be as per drawing No CEJZ/TD/1019, Sh 1/3 to 3/3 and No. CEJZ/TD/1020, Sh 1/3 to 3/3 can be seen at HQ CWE JRC during any working days. (ii) Glass, painting & grills shall be measured and paid separately.

Supply & fix Steel windows/ventilator 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mm x 25mm single rebated comprises of gauged skeleton shutter ERW Sec 50mmx20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box type ‘T’ section of size 60mmx25mm and 1.25mm thick including cuttings holes and making good dismantled portion in PCC (1:3:6) type B1 using 20mm graded stone aggregate. Four Nos for each window including following fittings welded to framed shutter :- (a) Mild steel holdfasts 150mm long 12mmx3mm made to shape per window -04 Nos, (b) Handle of Z Sec 20mmx25mm, 100mm long per leaf-01 No, (c) Stopper per leaf -01 Nos, (d) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges per leaf -01 No, (e) MS pintle hinges of size 75mmx75mmx12mm per leaf -02 Nos, complete all as specified in drawing No CEJZ/TD/1019, Sh 1/3 to 3/3 and No. CEJZ/TD/1020, Sh 1/3 to 3/3. Note : (i) Fabrication shall be as per drawing No CEJZ/TD/1019, Sh 1/3 to 3/3 and No. CEJZ/TD/1020, Sh 1/3 to 3/3 can be seen at HQ CWE JRC during any working days. (ii) Wire mesh, painting & grills shall be measured and paid separately.

Supply and fix framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes framed guard bars, barred iron doors,steel door frames, ladders, framed balusters, walk ways, railings, frame work or water tanks and similar work conforming to Gde Fe-290 or E-165 all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification in drawing and as per manufacturer's instructions.

Supply and fix 2nd class hard wood factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in clause 8.24 (a) of SSR Part-I; supplied and fitted to chowkhats complete all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & as per manufacturer's instruction complete all as specified and directed.

Supply & fix factory made PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement,fixing in the frame at the site as per specification & as per manufacturer's instruction. complete all as per specified and as directed by the Engineer in Charge.

Supply and fix 4 mm thick figured glass, pinhead type in squares n exc 0.5 sqm each pane complete all as specified and directed.

Supply & fix 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed

S&F mild steel barrel tower bolt, stove enamelled black with bright bolt of 150 mm size complete all as specified and directed.

Supply & fix mild steel pressed handles, oval type, stove enamelled black of size 125mm complete all as specified and directed.

Supply & fix 150mm long aluminium handles, cast type, anodised complete all as specified and directed.

Supply & fix 300mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts 150mm of extruded section and fixed complete all as specified and directed.

S&F grating doom of size 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S&F shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

Supply & fix in repair 100 mm dia cast iron floor trap with grating, including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Supply & fix in repair 100 mm dia cast iron nahani trap, including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Supply & fix in repair cast iron bends any radius 100 mm bore diminishing pieces or tapers (large bore measured) complete all as specified and directed.

S&F CI branch pieces, single pieces, (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches 100mm bore complete all as specified and directed.

S&F in repair 100 mm dia CI S or P trap complete all as specified and directed.

S&F 75 mm dia cast iron cowls complete all as specified and directed.

S&F 100 mm dia stack clamps made out of 50 mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F 32mm bore polyethylene pipe of low density (HDPE) or pressure rating pressure rating 6 kgf/sq. cm fixed to wall ceiling or in floor etc complete all as specified and directed.

Supply & fix 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

M&L for providing cement concrete type B-0 ,1:2:4 ( using 12.5 mm graded stone aggregate) for copings, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Material & labour for preparation of new plastered surface of walls and applying three coats of white washing complete all as specified and directed.

Material & labour for prepararion of old plastered surfaces of wall including preparation of surfaces and applying two coats of white wash complete all as specified and directed.

Material & labour for preparation of newly plastered surface of walls and applying two coats of cement base paint complete all as specified and directed.

Material & labour for preparation of old decorated plastered or unplastered surface of walls and applying one coat of cement base paint as per existing pattern complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Supply and fix 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Supply and fix galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

M&L for concrete bed for 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed.

Material & labour for PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in surface channels, drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified

Material & labour for preparation of old decorated wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material & labour for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material & labour for preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position including removing of demolished material from site complete all as specified and directed.

M&L for providing precast reinforced cement concrete 1:1.5:3 type A-1 (using 20 mm graded crushed stone aggregate) as in cover slab of main holes, septic tanks etc set in CM 1:4 including necessary form moulds etc complete all as specified and as directed (Reinforcement shall be measured and paid separately)

Material & labour for RCC (1:1.5:3) type A-0 using 12.5mm graded stone aggregate as in chajjas etc and the like surface finished even and smooth complete all as specified and as directed by Engr-in-charge including necessary scaffolding for ground floor and 1st floor.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for 6-8mm deformed TMT bar 5mm dia and over, deformed bar cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including cracking bending mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth in soft/loose soil taking and getting out complete all as specified and directed.

Material & labour for plain cement concrete type D-2 1:4:8 (using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and directed.

Returning filling in including spreading,levelling,watering, well ramming in layers not exc 25 cm each complete all as specified and directed.

Removal of surplus soil to a distance not exc 50 m and deposited where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Running welding in repairs, thickness of metal to be exc 6mm but not exc 9mm complete all as specified and directed.

S&F wire netting of galvanised steel wire 1.40mm dia & size of mesh 12mm fixed with tinned tacks or wire staples complete all as specified and directed.

Demolition of mud in roofs any thickness including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified.

Material & labour for 15 mm thick rendering in cement mortar (1:4) on concrete surfaces finished even and smooth with and including liquid water proofing compound as per manufacturer's instructions complete all as specified

M&L for preparation of new concrete surface and apply water proofing treatment to roof with APP (Atactic poly propylene) modified prefabricated five layer 3 mm thick water proofing membrane super therolay of STP limited with polyster non woven fabric reinforcement of 160gm, minimum weighing 3.6kg/sqm over a solvent based bitumen primer, shalitex primer @ 0.3 ltr/sqm by the same manufacturer conforming to IS-3384-1986. Apply two coat of aluminium paint on top of membrane surface after laying the membrane incl all cleaning complete all as specified and directed. Note: The membrane shall be laid using butane torch. The end lap should be 100mm and the side lap must be minimum 75mm. The membrane shall be first laid upto the parapet wall junction and then shall be overlapped withanother membrane (flashing) with and overlap covering upto a distance of 300mm. In case of parapet height is less than/upto 500mm membrane shall be terminated at the top of parapet.

M&L for cement concrete type B-2, 1:2:4 (40mm graded aggregate as in padding complete all as specified and directed.

Dismantling of brick tiles or terracing tiles single layer as in roof covering complete all as specified

Material & labour for 40mm thick brick tiles laid on cement mortar of 15mm thick (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed.

All as per item No. 99 above but except tiles complete all as specified and directed.

M&L for 150mm dia RCC NP-3 drain pipes laid in trenches and jointed as specified complete all as specified and directed.

Dismantling cast iron work of any description complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for 100 mm bore sand cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors or fixed to walls complete all as specified and directed.

All as per srl item No. 90 above but 75mm dia complete all as specified and directed.

S&F Soap dish steel chromium plated complete all as specified and directed.

Supply and fix 3.15 mm thick plain mild steel wire, galvanised class 3, in detached work such as mosquito nets/hangingcloths etc incl brackets and fixing to straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) complete all as specified and directed

Taking down carefully existing point wiring aluminum/ copper conductor for light or fan or socket or power etc on wooden batten or in conduit including fittings and accessories like switches, sockets, lights fitting, regulator, wooden board and making good disturbed portion to match with existing complete all as specified and directed.

Material & labour for concealed point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated and unsheathed cable 1100 volts multistranded, copper conductor cable (FRLS) drawn through and including PVC concealed conduit not less than 20mm dia bore medium grade (ISI marked) and accessories like bends, tees, junction boxes etc, fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including sunken type pressed steel terminal boxes and plastic laminated white/ coloured top sheet cover 3.0 mm thick , for One light point / fan point controlled by one way switch and/or through regulator complete all as specified and directed.

All as per item No. 109 above but one 3 pin socket outlet 6 amps on same board complete all as specified and directed.

Material & labour for concealed point wiring complete with single core 2.5 Sqmm (nominal area) PVC insulated and unsheathed cable 1100 volts multistranded, copper conductor cable (FRLS) drawn through and including PVC concealed conduit not less than 20mm dia bore medium grade (ISI marked) and accessories like bends, tees, junction boxes etc, fix on wall or ceiling surfaces all as specified including 2.5 sqmm , FRLS type , copper multistranded cable as earth wire including sunken type pressed steel terminal boxes and plastic laminated white/ coloured top sheet cover 3.0 mm thick , and connecting the earth dolly for6 pin, 16 amp socket outlet on independent board complete all as specified and directed.

Supply and fix switch piano flush button type, 5 Amps, 230V AC, single pole, one way complete all as specified and directed

Supply and fix switch piano flush button type, 15 Amps, 230V AC, single pole, one way complete all as specified and directed

Supply and fix socket out let multi purpose 2 in 1, 5 pin 5 Amp flush type 230/250 volts complete all as specified.

Supply and fix socket out let 2 in 1, 6 pin 15 Amp flush type 230/250 volts complete all as specified.

Supply and fix ceiling rose surface type bakelite 65 x 50 mm three terminal PVC / Polycarbonate isolated body complete all as specified.

Taking down old unserviceable fluorescent tube light fitting 36/40 watt direct to walls or roof as ordered complete all as specified.

Supply & Fix 20 watt 4 ft long LED retrofit T8 tube complete with powder coated CRCA decorativepatti including LED tube rod with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 complete all as specified and directed by Engr-in-Charge. Make : C & S Cat Part No LTDCD1220W LED/WD or equivalent makes as in Appx 'B'

Supply & fix bulkhead fitting decorative ceiling/wall mounted bulk head with engineering plastic housing and top frame with opal PMMA diffuser suitable for 1 x 06 watt LED bulb including 1 No 06 watt LED and connecting up complete with 3 core flexible cable of size 23/0.0076 complete all as specified and directed by Engr-in-Charge. Make : C&S Cat part No. CG80IB6WLED or equivalent as in Appx 'B' Note for item 118 & 119 : Contractor will submit two year guarantee certificate from company

Taking down unserviceable MCBs and supply & fix MCB, 6 to 32 amp, SP, 240 Volts complete all as specified and directed.

Taking down unserviceable MCBs and supply &fix MCB, 32 to 63 amp, SPN, 240 Volts complete all as specified and directed.

Taking down unserviceable MCBs and supply & fix MCB, 40 to 63 amp, TP, 240 Volts complete all as specified and directed.

Taking down unserviceable MCBs and supply &fix MCB, 40 to 63 amp, TPN, 240 Volts complete all as specified and directed.

Taking down old unserviceable sub main wiring and Material & labour for submain wiring with two runs of single core 10 Sqmm (nominal area) 1100 volts grade PVC insulated unsheathed multistranded copper conductor cable (FRLS) drawn through and including PVC conduits not less than 20mm dia medium grade rigid concealed conduit and conduit accessories and 10 sqmm PVC insulated copper wire green in colour as earthing lead drawn through existing for continuous earth continuity conductor all as specified and directed by Engr-in-charge. Note : Two run of 10sqmm cable and one run of 10sqmm cable as earth continuity conductor alongwith PVC conduit shall be measured and paid as one unit.

Taking down old unserviceable sub main wiring and Material & labour for submain wiring with two runs of single core 6 Sqmm (nominal area) 1100 volts grade PVC insulated unsheathed multistranded copper conductor cable (FRLS) drawn through and including PVC conduits not less than 20 mm dia medium grade rigid concealed conduit and conduit accessories and 6 sqmm PVC insulated copper wire green in colour as earthing lead drawn through existing for continuous earth continuity conductor all as specified and directed by Engr-in-charge. Note : Two run of 6sqmm cable and one run of 6sqmm cable as earth continuity conductor along with PVC conduit shall be measured and paid as one unit.

Taking down old unsv DB and S&F factory made sheet metal enclosure double door distribution board class IP-43 with 200 amp rated copper bus bar 420 V, 4 way TPN including 100 amps MCCB , 4P, 16 KA, 3 pole and neutral link complete all as specified and directed.

Taking down old unsv DB and S&F factory made sheet metal enclosure double door distribution board class IP-43 with 200 amp rated copper bus bar 240 V, 8 way with neutral link complete including making good the disturbed surface all as specified and directed.

COSMO BUILDERS

KAMAL AGGARWAL

Motorway Constructions