864/WS-27/2022-23

Amount

Servicing of Diesel Engine Generating sets of 7.5 KVA to 45 KVA rating to be carried out as per schedule given as under :- (A) B - Check :- (Every 100 hrs or 6 Months whichever is earlier) (i) change lubricating oil (ii) change lubricating oil filters (iii) change fuel filter (iv) change coolant (v) check engine wiring for damage (vi) check drain fuel supply tank (vii) change by pass lubricant filter (viii) change air filter (ix) check oil pressure (x) change fuel water separator (B) C- Check:- (Every 1500 Hrs or 1 Years Whichever is earlier) (i) Adjust valve (ii) steam clean engine (iii) replace hose if required (iv) check turbo charger mounting nuts (v) check engine oil heater (vi) Check all electrical connection (vii) Check pollution level (viii) change oil (ix) Change oil filter / fuel filter / by pass filter (x) Change air filter (xi) Change water separator (xii) inspect following parts & replace if required (alternator, starter etc) (xiii) clean fuel tank from inside. Note: (i) Maintenance of Diesel Engine Generating Set as per maintenance schedule chart (ii) Schedule of service, Diesel Gen Set Machine No Wise attached in Particular specification. (iii) Servicing of DG set will be done by Authorised dealer of Kirloskar / Cummins / Greave / mahindra only. (iv) B Check and C Check spare parts will be measured and paid separately under supply only items (fixing charge included with the servicing of DG set item No 1 to 8)

Ditto all as per serial item No.1.00 described here-in-before but DG Set 62.5 / 63 KVA rating

Ditto all as per serial item No.1.00 described here-in-before but DG Set 75 /100 KVA rating

Ditto all as per serial item No.1.00 described here-in-before but DG Set 125KVA rating.

Ditto all as per serial item No.1.00 described here-in-before but DG Set 160 KVA rating

Ditto all as per serial item No.1.00 described here-in-before but DG Set 180 /200 KVA rating

Ditto all as per serial item No.1.00 described here-in-before but DG Set 250 KVA rating

Ditto all as per serial item No.1.00 described here-in-before but DG Set 320 / 380/ 400 KVA rating

Supply only fuel filter element with 'O' ring for 7.5 KVA to 45 KVA DG Set Complete all as specified and as directed.

Supply only fuel filter element with 'O' ring for 62.5/ 63 KVA DG Set Complete all as specified and as directed.

Supply only fuel filter element with 'O' ring for 75 / 100 KVA DG Set Complete all as specified and as directed.

Supply only fuel filter element with 'O' ring for 125 DG Set Complete all as specified and as directed.

Supply only fuel filter element with 'O' ring for 160 KVA DG Set Complete all as specified and as directed.

Supply only fuel filter element with 'O' ring for 180 / 200 KVA DG Set Complete all as specified and as directed.

Supply only fuel filter element with 'O' ring for 250 KVA DG Set Complete all as specified and as directed.

Supply only fuel filter element with 'O' ring for 320 / 380/ 400 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 7.5 KVA to 45 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 62.5 / 63 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 75 / 100 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 125 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 160 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 180 / 200 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 250 KVA DG Set Complete all as specified and as directed.

Supply only oil filter cartage element with O ring for 320 / 380/ 400 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 7.5 KVA to 45 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 62.5/ 63 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 75 / 100 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 125 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 160 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 180 / 200 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 250 KVA DG Set Complete all as specified and as directed.

Supply only air filter (both outer & inner) element with O ring for 320 / 380/ 400 KVA DG Set Complete all as specified and as directed.

Supply only bye pass lubricant oil filter cartridge element with O ring for 380 /400 KVA DG Set Complete all as specified and as directed.

Supply only engine oil 15W 40 grade in DG set complete all as specified and directed. Make :- K oil super by Kirloskar/ Castrol/ Servo

Drain out old and unserviceable coolant and Supply and fill coolant premixed complete all as specified and directed.

Supply & fill distilled water for battery complete all as directed.

Supply and fix in replacement V belt off size, Make - fenner or equivalent as approved by GE complete all as per site requirement and all as specified and as directed.

Material and labour for cleaning of radiator assembly whole generator inside & outside for DG set of capacity 7.5 to 62.5 / 63 KVA by dismantling of Canopy, Removal of Radiator, Cleaning of radiator with chemical, sealing power Wash of radiator tube if any leakage, pressure testing of radiator, arrest leakage by bazing soldering incl freight (to & fro), loading, unloading, re-assembly of canopy complete all as specified and directed by Engr-in-charge.

Ditto all as per serial item No. 38.00 described here-in-before but for DG set of capacity 75 to 125 KVA

Ditto all as per serial item No. 38.00 described here-in-before but for DG set of capacity 160 KVA

Ditto all as per serial item No. 38.00 described here-in-before but for DG set of capacity 180/200 KVA

Ditto all as per serial item No. 38.00 described here-in-before but for DG set of capacity 250 KVA

Ditto all as per serial item No. 38.00 described here-in-before but for DG set of capacity 320 to 400 KVA

M&L for dismantling dynamo/alternator of battery charging complete servicing including replacement of bushes bearing, carbon brushes, diodes any other minor parts required all as directed and fixing on engine testing/ commissioning complete for engine having any capacity for 12 volts all as specified and directed by Engr-in-charge.

M&L for dismantling dynamo/alternator of battery charging complete servicing including replacement of bushes bearing, carbon brushes, diodes any other minor parts required all as directed and fixing on engine testing/ commissioning complete for engine having any capacity for 24 volts all as specified and directed by Engr-in-charge.

M&L for calibration of Injector Nozzle Removal of Injector Nozzle from engines of 62.5 KVA to 125 KVA DG capacity, calibration of these nozzle at fuel pump from authorized calibration bench, if parameters are out of limit then replacement of nozzles and connected spares.

M&L for calibration of Injector Nozzle Removal of Injector Nozzle from engines of 160 -250 kVA DG capacity, calibration of these nozzle at fuel pump from authorized calibration bench, if parameters are out of limit then replacement of nozzles and connected spares.

M&L for calibration of Injector Nozzle Removal of Injector Nozzle from engines of 320-400 kVA DG capacity, calibration of these nozzle at fuel pump from authorized calibration bench, if parameters are out of limit then replacement of nozzles and connected spares.

M&L for decarburization of Cylinder Head Removal of Cylinder head from engine, chemical wash at workshop, checking of valve, seat, guides etc in head, lapping, if required or replacement of spare if required. Removal of carbon from head by chemical wash. Refitment on engine replacement of all the gaskets required throughout the process. Tappet setting if required for the DG Set of capacity 320 kVA to 400 kVA

M&L for decarburization of Cylinder Head Removal of Cylinder head from engine, chemical wash at workshop, checking of valve, seat, guides etc in head, lapping, if required or replacement of spare if required. Removal of carbon from head by chemical wash. Refitment on engine replacement of all the gaskets required throughout the process. Tappet setting if required for the DG Set of capacity 160 kVA to 250 kVA

M&L for decarburization of Cylinder Head Removal of Cylinder head from engine, chemical wash at workshop, checking of valve, seat, guides etc in head, lapping, if required or replacement of spare if required. Removal of carbon from head by chemical wash. Refitment on engine replacement of all the gaskets required throughout the process. Tappet setting if required for the DG Set of capacity 62.5 kVA to 125 kVA

Dismantling and taking down old/unserviceable lead acid battery from DG set and S&F new lead acid battery, 12 volt, 180 AH capacity complete with brass terminals incl testing on load all as directed. Make :- Exide, Model - New Express / Amron

Supply and fixing Battery lead of 1.5 meter long with multstranded copper conductor of size 50 sqmm single core PVC insulated, flexible. With battery terminal at one end and long tube terminal eye type at other end.

M&L for calibration of DG Sets from the authorised dealer of Kirloskar/ Mahindra/ cumins FIP, removal of injector nozzle form engine and refix the same after calibration of DG set 62.5 kVA to 125 kVA capacity of from the authorised dealer.

M&L for calibration of DG Sets from the authorised dealer of Kirloskar/Mahindra/cumins FIP, removal of injector nozzle form engine and refix the same after calibration of DG set 160 to 400 kVA capacity of from the authorised dealer.

M&L for servicing of self starter assembly of DG sets 12 volts by dis connecting the self starter assembly from the engine and dismantling, cleaning all accessories, replacing worn-out parts like carbon brushes, penion of existing teeth, bendex bushes, Armature, solenoid Assy 12 volt contact plates, jumping levels etc and rewinding the u/s field coil etc and varnishing all as specified and directed by Engr-in-charge.

M&L for servicing of self starter assembly of DG sets 24 volts by dis connecting the self starter assembly from the engine and dismantling, cleaning all accessories, replacing worn-out parts like carbon brushes, penion of existing teeth, bendex bushes, Armature, solenoid Assy 24 volt contact plates, jumping levels etc and rewinding the u/s field coil etc and varnishing all as specified and directed by Engr-in-charge.

Supply and fixing in replacement of turbo charger suitable for 160 KVA DG Set complete all as specified and directed

Taking out unserviceable heat proof Asbestos rope from the exhaust pipe cleaing the exhaust pipe and supply & wraping new asbestos rope of suitable size and wrapping with wire mesh and plastering with of paris/white cement for smooth finishing including replacement of gasket and tightening of all nut and bolts all as directed by engineer in charge

M&L for cleaning the fuel tank both internally and externally by removing all the dust / sediments etc to be cleaning for various capacities of DG Set.

Supply in fixing in replacement rubber hose pipe set with clamps suitable for 62.5 kVA to 125 of DG sets

Supply in fixing in replacement rubber hose pipe set with clamps suitable for 160-400 kVA of DG sets

Supply and fixing in replacement of fuel pipe as per sample.

Supply and fixing in replacement of fuel level indicator transperent PVC pipe of suitable dia for the fuel tanks

Supply and fixing in replacement turbo charger repair kit assemebly suitable for 62.5/63 -125 kVA capacities of DG set

Supply and fixing in replacement turbo charger repair kit assemebly suitable for 160-200 capacities of DG set

Supply and fixing in replacement turbo charger repair kit assemebly suitable for 250 to 400 capacities of DG set

Supply and fix in replacement of solenoid switch suitable for 62.5 to 125 KVA complete as directed as per sample.

Supply and fix in replacement of electronic governer with actuataor & GCU incl complete electric connection all as specified and directed by Engr-in-charge.

Supply and fix in replacement of electronic governer with actuataor & ECU incl complete electric connection all as specified and directed by Engr-in-charge.

S&F generator Battery Charger, input voltage 230V, output voltage 12V and 24V, fully automatic over boost/float cutoff charger, automatic over charge and over discharge protection.battery reverse protection with indication suitable for charging storage type lead acid battery in existing LT/DG Panel including making necessary connections from charger to battery by using 10 sqmm copper conductor heavy duty cable and clamps.

Supply and fixing in replacement Offload Change over Switch cubical type 4 pole of rating 630 Amps, confirming to IS-13947 (Part 3) with rotary handles.

Supply and fixing in replacement Offload Change over Switch cubical type 4 pole of rating 400 Amps, confirming to IS-13947 (Part 3) with rotary handles.

Supply and fixing in replacement Offload Change over Switch cubical type 4 pole of rating 320 Amps,confirming to IS-13947 (Part 3) with rotary handles.

Supply and fixing in replacement Offload Change over Switch cubical type 4 pole of rating 200A Amps, confirming to IS-13947 (Part 3) with rotary handles.

Supply and fixing in replacement Offload Change over Switch cubical type 4 pole of rating 100 Amps, confirming to IS-13947 (Part 3) with rotary handles.

Supply and fixing in replacement Offload Change over Switch cubical type 4 pole of rating 63 Amps, conficrming to IS-13947 (Part 3) with rotary handles.

Supply & fixing in replacement MCCB 400 amp, 4 pole, 415 volts, 50 Hz AC with thermal magnetic setting with adjustable protection for over load and short circuit. The MCCB should have Ics = 50% Icu for short circuit breaking capacity of 36KA.

Supply & fixing in replacement MCCB 320 amp, 4 pole, 415 volts, 50 Hz AC with thermal magnetic setting with adjustable protection for over load and short circuit. The MCCB should have Ics = 50% Icu for short circuit breaking capacity of 36KA.

Supply & fixing in replacement MCCB 250amp, 4 pole, 415 volts, 50 Hz AC with thermal magnetic setting with adjustable protection for over load and short circuit. The MCCB should have Ics = 50% Icu for short circuit breaking capacity of 25KA.

Supply & fixing in replacement MCCB 250 amp, 3 pole, 415 volts, 50 Hz AC with thermal magnetic setting with adjustable protection for over load and short circuit. The MCCB should have Ics = 50% Icu for short circuit breaking capacity of 25 KA.

Supply & fixing in replacement MCCB 160 amp, 3 pole, 415 volts, 50 Hz AC with thermal magnetic setting with adjustable protection for over load and short circuit. The MCCB should have Ics = 100% Icu for short circuit breaking capacity of 25KA.

Supply & fixing in replacement MCCB 100 amp, 3 pole, 415 volts, 50 Hz AC with thermal magnetic setting with adjustable protection for over load and short circuit. The MCCB should have Ics = 100% Icu for short circuit breaking capacity of 16KA.

Supply only Aluminium terminal (lugs) of Size 400 sqmm Make : Dowell / Jackson

Supply only Aluminium terminal (lugs) of Size 300 sqmm Make : Dowell / Jackson

Supply only Aluminium terminal (lugs) of Size 240 sqmm Make : Dowell / Jackson

Supply only Aluminium terminal (lugs) of Size 185 sqmm Make : Dowell / Jackson

Supply only Aluminium terminal (lugs) of Size 150 sqmm Make : Dowell / Jackson

Supply only Aluminium terminal (lugs) of Size 120 sqmm Make : Dowell / Jackson

Supply only Aluminium terminal (lugs) of Size 95 sqmm Make : Dowell / Jackson

Supply only Aluminium terminal (lugs) of Size 70 sqmm Make : Dowell / Jackson

M&L for servicing of alternator/AVR of DG set of capacity 30 to 75 KVA of any make and type by disconnecting all connections and removing dust from alternator/AVR and checking of wiring complete if burnt repalace the wire and making connection of all component all per specified and as directed by Engr-in-Charge

M&L for servicing of alternator/AVR of DG set of capacity 100 to 125 KVA of any make and type by disconnecting all connections and removing dust from alternator/AVR and checking of wiring complete if burnt repalace the wire and making connection of all component all per specified and as directed by Engr-in-Charge

M&L for servicing of alternator/AVR of DG set of capacity 160 to 200 KVA of any make and type by disconnecting all connections and removing dust from alternator/AVR and checking of wiring complete if burnt repalace the wire and making connection of all component all per specified and as directed by Engr-in-Charge

M&L for servicing of alternator/AVR of DG set of capacity 250 to 400 KVA of any make and type by disconnecting all connections and removing dust from alternator/AVR and checking of wiring complete if burnt repalace the wire and making connection of all component all per specified and as directed by Engr-in-Charge

M&L for earthing complete with galvanized iron or steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtrs below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to galvanized earth strip 32X6 mm by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate), with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge of (0.68mm) 8 mesh per liner inch, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I and specified including provision of earth wire protected by 40mm dia medium grade GI pipe and watering pipe shall be 20mm bore medium grade GI pipe, and including all excavation and earth work & connecting the earthing to an earthing test point /DG Set neutral/ body/ Lt panel etc. and testing on completion, complete all as specified & directed by Engr-in-Charge.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in conduit/pipes or fixed to poles or any other indicated suituations for loop earthing etc as required of size 32x6mm all as specified & directed.

Repair / overhauling of electrical control panel board including addition alteration in wiring system complete with of defective parts such as volt meter Ammeter, frequency meter indicating lamps with wiring etc.Note :- Cost of spares shall be measured and paid separatly.

Taking out the unserviceable oil pressure guage and supply and fixing oil pressure guage ISI marked complete all as specified and as directed.

Taking out the unserviceable Oil temprature guage and supply and fixing water oil temprature guage ISI marked complete all as specified and as directed.

Taking out the unserviceable fuel guage meter and supply and fixing fuel guage meter ISI marked operated on 12V/24V DC complete all as specified and as directed.

Supply and fixing Digital RPM cum hour meter suitable to operate on 8 to 32 DC Voltage with all associated acessories like cable, sensor bracket etc including for smooth functioning in various DG set installation

Supply and fixing Indicator lamp neon type red, yellow & blue complete all as specified and directed.

Taking down, disconnecting and shifting of existing DG Set of capacity 160 KVA to 400 KVA from old location to new location including disconnecting and shifiting LT panels change over switch etc. and providing connections to new location complete all as directed. Note : DG set shall be shifted with proper safety using crane hydra/T&P/man power as required and same is deemed to be incl in quoted rates.

Taking down, disconnecting and shifting of existing DG Set of capacity 62.5 KVA to 125 KVA from old location to new location including disconnecting and shifiting LT panels change over switch etc. and providing connections to new location complete all as directed. Note : DG set shall be shifted with proper safety using crane hydra/T&P/man power as required and same is deemed to be incl in quoted rates.

Supplying, laying in trench or through wall by clamping, and testing XLPE insulated heavy duty electric cables with aluminium conductor 1100 volts grade of size 300 Sqmm 3.5 core complete all as specified and directed. Make : Havells / Polycab / Gloster

Supply and fixing in repairs straight through (Heat shrinkable) joint kit suitable for 1.1 KV UG XLPE cable of size 300 Sqmm 3.5 core. Make : Raychem / Denson / 3M

Supply and fixing in repairs straight through (Heat shrinkable) joint kit suitable for 1.1 KV UG XLPE cable of size 70-120 Sqmm 3.5 core. Make : Raychem / Denson / 3M

M&L for preparation of old painted steel/RCC surfaces of any description and in any situation over 10 cm width or grith and applying two coat of synathetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for writing letters or figures (Nos, Block, Roman, Italic or Indian) n exc 30 cm high with one coat of synthetic enamel paint complete all as specified.

Supply & fix GCU as per sample & of same make incl wiring with copper conductor single core 4 sqmm for 200 kVA DG set. Make : Kirloskar cummins model No. KTA 1150 G.

Supply & fix AVR (Automatic voltage regulator) for 62.5 kVA-125 kVA DG set as per sample and of same make all as per specified and directed by Engineer-in- charge

Supply & fix AVR (Automatic voltage regulator) for 160 kVA-400 kVA DG set as per sample and of same make all as per specified and directed by Engineer-in- charge

Removing existing paint, oil from body of engine, alternator, pump, radiator mounting, base frame including exposed portion of silencer, fuel tank complete gen set, preparing surface and spray (workshop premixed paint) painting the Gen Set of capacity 62.5 kVA to 125 kVA complete with two coats of synthetic enamel paint over a coat of red oxide. Colour codes of paint shall be directed by the Engr-in-Charge.

Removing existing paint, oil from body of engine, pump, radiator mounting, base frame including exposed portion of silencer, fuel tank complete gen set, preparing surface and spray (workshop premixed paint) painting the Gen Set of capacity 160 kVA to 400 kVA complete with two coats of synthetic enamel paint over a coat of red oxide. Colour codes of paint shall be directed by the Engr-in-Charge.

Supply & fixing cylinder head assembly incl head gasket gas complete for 200 kVA DG set. Make : Greaves TBD -3-V MKI BS 5514

Supply and fix on wall single shaded reflective sign board of high intensity reflective sheet computer cut back ground of sky blue/green colour and white letters (letters and diagrams to be written on the board, shall be provided by JE E/M / Engineer-in-Charge) mounded on harden alloy aluminium sheet 2 mm thick fixed on angle iron frame and supported by angle iron/ square tubes incl fixing arrangement on wall complete all as per manufacturer's instruction and as specifed and directed by Engineer-in-Charge Note- Rates deemed to be included for angle iron/square tube frames, supports, nuts and washers etc complete all as directed by Engineeer-in-Charge.

Dismantling the steam boiler coil & descaling of Steam Boiler 600Kg/Hr by opening of boiler coil cover from the both sides including disconnecting of inlet and outlet water connections of the boiler. Closing both side of coil and circulating the descaling compound solution in tubes of boiler through the separate circulating pump and allow the descaling solution to hold for 1hr for chemical reaction. After the duration of 1 hr open the coil ends and ensuring that the coil has been descaled upto max clean range, then closing both the ends of the coil and circulating clean water in the tubes of boiler and draining it out, the process will be continued till the satisfaction of Engr-in-Charge then refixing the coil inside the chamber complete with all fixing material required at site:

Supply & fixing in replacement of photo cell complete with holder.

Supply & fixing in replacement of ignition transformer (14500V).

Supply & fixing in replacement of Pressure gauge 4'' dia Connection centre back mount, dial range - 20 kg to 25 kg as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of temperature gauge dia 2'' Connection centre back temperature rod as per sample complete all as directed by Engr-in-Charge.

S&F in repacement of electric hooter for boiler 600 Kg/hrs as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of heavy duty steam pressure gate/ball Valve 15 to 25 mm dia as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of heavy duty NRV valve 15 to 25 mm dia, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of copper tube dia 8 mm/12 mm as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of heavy duty inlet/outlet hose pipe with wire mesh of any size and any length as per sample complete all as directed by Engr-in-Charge.

M&L for rewinding of burnt motor from respective laundry/CHS machines by disconnecting all electrical and mechanical connections and reassembling, testing of the same after carrying out rewinding of motor of under mentioned capacity single/three 3ph 415Volt, 50Hz with supper enamelled copper wire having same gauge after taking out old burnt winding including replacement of bearing of capacity 1HP to 2HP complete and all as specified.

M&L for rewinding of burnt motor from respective laundry/CHS machines by disconnecting all electrical and mechanical connections and reassembling, testing of the same after carrying out rewinding of motor of under mentioned capacity single/three 3ph 415Volt, 50Hz with supper enamelled copper wire having same gauge after taking out old burnt winding including replacement of bearing of capacity 3HP to 5HP complete and all as specified.

M&L for rewinding of burnt motor from respective laundryCHS machines by disconnecting all electrical and mechanical connections and reassembling, testing of the same after carrying out rewinding of motor of under mentioned capacity single/three 3ph 415Volt, 50Hz with supper enamelled copper wire having same gauge after taking out old burnt winding including replacement of bearing of capacity 7.5HP to 10HP complete and all as specified.

M&L for rewinding of burnt motor from respective laundry /CHSmachines by disconnecting all electrical and mechanical connections and reassembling, testing of the same after carrying out rewinding of motor of under mentioned capacity single/three 3ph 415Volt, 50Hz with supper enamelled copper wire having same gauge after taking out old burnt winding including replacement of bearing of capacity 12.5HP to 20HP complete and all as specified.

Supply & fixing in replacement of V Belt for Washer Extractor of capacity - 60 Kg, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Main drain valve (actuator butterfly valve) for Washer Extractor of capacity - 60 Kg, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Main water inlet valve (actuator butterfly valve) for Washer Extractor of capacity - 60 Kg as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of single solenoid valve for Washer Extractor of capacity - 60 Kg, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Door gasket for Washer Extractor of capacity - 60 Kg, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Hose pipe of dia 4" for Washer Extractor of capacity - 60 Kg, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of V Belt for washer extactor of capacity - 30 Kg, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of silicon oil seal with circlip & O ring for Slucing machine of capacity - 30 Kg, as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Flannel Cloth for flat work ironer Size 32''x13'', as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Final cover for flat work ironer Size 32''x13'', as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Main Bearing Set for flat work ironer Size 32''x13'', as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Main drive V belts for Drying tumbler as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Automatic steam inlet valve for Drying tumbler as per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of Contactor for Drying tumbleras per sample complete all as directed by Engr-in-Charge.

Supply & fixing in replacement of solenoid Valve for Vaccum ironing machine as per sample

Supplying, mixing and filling of mono ethylene glycol concentrate along with the necessary additives and inhibitor in cognition, required for operation of plant and network. The mixing freezing temperature shall be minus 10 degree C all as sprecified and directed by Engr-in-Charge.

Supply and mixing Hydro caloric acid (HCL) concentrate.

Supply and fixing in replacement under mentioned items for oil fired incinerator model PY-VS-75 as per sample complete all as directed by Engr-in-Charge.

S&F Fuel filter element per sample complete all as directed by Engr-in-Charge.

S&F Thermo couple K type per sample complete all as directed by Engr-in-Charge.

S&F Pressure gauge 0-40 Kgs/Cm 2-1/4" BSP per sample complete all as directed by Engr-in-Charge.

S&F Electrode front pair per sample complete all as directed by Engr-in-Charge.

S&F in replacement of solenoid valve of incinerator as per sample complete all as directed by Engr-in-Charge.

S&F Electrode rear pair as per sample complete all as directed by Engr-in-Charge.

S&F Sequence controller as per sample complete all as directed by Engr-in-Charge.

S&F Oil seal for fuel pump as per sample complete all as directed by Engr-in-Charge.

S&F HT cable as per sample complete all as directed by Engr-in-Charge.

S&F Spider LO-70 (Rubber Bush) as per sample complete all as directed by Engr-in-Charge.

S&F in replacement of main steam inlet valve automatic for washer extractor 60 Kg aper sample complete all as directed by Engr-in-Charge.

S&F in replacement of thermocouple for washer extractor 60 Kg as per sample complete all as directed by Engr-in-Charge.

Supply and mixing industrial salt in water for descaling for steam boiler 600 Kg/hr

S&F in replacement of touch screen HMI for washer extractor 60/30 Kg or as per site reqirement as per sample.

Supply and mixing descaling compound for steam boiler 600 Kg/hr per sample complete all as directed by Engr-in-Charge.

M&L for dismentaling/opening of old damage heavy duty MS pipe fittings from bilers of any shape/size and replacement with new as heavy duty MS pipe fitting as per site requirement including necessary threading, welding work, flange, gasket of any size with nut bolts complete all as directed by Engr-in-Charge

M&L for opening of Primary and Secondry chamber of incinerator and replacment of all damege/burnt items after repair reassemling of plant, as per sample complete all as directed by Engr-in-Charge.

M&L for high temprture resistance Painting of Incinretor boilers complete with synthetic high tempreture enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. by Wire brushing and cleaning top surface complete all as directed by Engr-in-Charge.

M&L for dismantling/ opening of loundery and after repair reassemling of plant, under mentioned items for Loundery as per sample complete all as directed by Engr-in-Charge.

S&F Gland washer HTN008N for boiler complete all as directed

S&F valve assembly HTB/ VA for boiler complete all as directed

S&F air release valve high pressure complete all as directed

S&F Butterfly valve high pressure25mm complete all as directed

S&F Butterfly valve high pressure 20mm complete all as directed

S&F NRV size 25mm complete all as directed

S&F Blow down valve size 20mm complete all as directed

S&F Y Stainer size 15mm A 55 complete all as directed

S&F gate valve 15mm complete all as directed

S&F PVC washer for valve gauge HTB/002 complete all as directed

S&F V belt size A 55 complete all as directed

S&F Gas kit for Laundry complete all as directed

S&F fuel filter complete all as directed

S&F fuel pipe complete all as directed

M/S TAHIRA ENTERPRISES

M/S FAISAL TRADING CO.

M/S SMA and SONS CONSTRUCTIONS

M/S MAS Electricals