ADDN/ALTN OF BOUNDARY WALL BETWEEN KV AND AFS AT VSN NAGPUR

Amount

Excavation over areas not exceeding 1.5 M deep and getting out in Hard/ Dense Soil/old foundation

M & L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

M & L for Reinforced Cement Concrete M-25 design mix (using 20 mm graded granite stone aggregate) in foundations including rafts, footings and plinth beams mass concrete complete all as specified and as directed.

M & L for Reinforced Cement Concrete M-25 design mix (using 20 mm graded granite stone aggregate) in Columns, piers, posts and struts complete all as specified and as directed.

M & L for Reinforced Cement Concrete M-25 design mix (using 20 mm graded granite stone aggregate) in walls complete all as specified and as directed.

M & L for Rough finished form work to sides of concrete foundations,footings,bases of columns, rafts and raft beams,sides and soffits(if any) of foundation and plinth beams and similar work vertical or batter complete all as specified and as directed.

M & L for Rough finished formwork to sides Square, rectangular or polygonal to sides of pillars, posts, struts, columns and stanchions complete all as specified and as directed.

M & L for Rough finished Form work to faces of walls ,retaining walls,abutments,parapets and staircase railings and similar work including attached pillasters,buttresses etc. vertical or to batter complete all as specified and as directed.

M & L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

M & L for Mild steel TMT 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

M & L for Mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming complete all as specified and as directed.

Removing Excavated soils exc 50 M and not exc 100 M depositing where directed at a level not exc1.5 M above the starting point complete all as specified and as directed.

M & L for Mild steel angles , bars , flats, etc as in supports for stiffening of fencing , wall ties, hold fasts, clamps plain angle cleats for securing purlins and similar small articles confirming to Fe 410-O or Fe 310-O complete all as specified and as directed.

S & F Mild steel screw bolts (machine made) 16 to 20 mm dia of shank with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10cm but n exc 15cm long complete all as specified and as directed.

M & L for Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and labour for concertina coil razer blade type of 1000mm dia inclunding horintal barbed wire razer blades type 6 No. For fixing the coil and necessary clips etc. Complete all as specified and as directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing new plastered surfaces and applying Two coats of cement base paint on surfaces of walls complete all as specified and as directed.

Supply only integral water proofing compound ISI Marked complete all as specified and as directed.

M/s ABHIMAN HEGDE

Harsh Construction Company