Provision and construction of Limited Height Subways (LHS) in lieu of existing manned level crossings No. CT-29 at km 424/14-16, No. CT-65 at km 473/29-31, No. JB-12 at km 438/14-16, No. CT-42 at km 449/9-11 and at the trespassing location at km 140/29-31 in between various stations/sections of Khurda Road (KUR) Division, including EI works of Siemens make.

A1-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All

A2-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All

B1-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All

B2-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All

B3-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All

C -SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE INCLUSIVE

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR.

Item- 1 EXECUTION OF SIGNALLING WORKS

S No. Item Description of Item Unit Qty Rate Amount

KHURDA ROAD DIVISION-S AND T/ECOR

1 1 Installation/Alteration/Phase working, Wiring, Station 2.00 1314621.00 2629242.00

testing and commissioning of complete

Electronic Interlocking System

(Distributed/Centerlized Configuration

System with Hot Stand by feature) supplied

as per Item Nos. 01 of Schedule-B-I including

transportation from Consignee's depot to site

of work. This includes execution of labour

portion, Interface relay wiring, erection of

relay racks, fixing of relays and associated

work in relay room, proper fixing of Operator

VDU Terminals etc (The Relays for interface

relays wiring will be supplied by Railways.

The Contractor shall supply all other

materials required for installation, wiring,

testing and commissioning). NOTE:- 1)

Installation & commissioning of Electronic

Interlocking is as per Section-H , Chapter-08.

2) If it is phase working, other than initial

phase design, supply of application logic

required for phase working should be done

by the Contractor agianst this item. 3) The

work includes manufacture/ fabrication,

supply and installation of SM's console and

side table extension as per site requirement

and as advised by site Engineer to

accomodate VDUs, other S&T equipments

and SM's stationary for operation of VDUs

and execution of day to day work for

operation of trains.

2 2 Factory acceptance test (FAT) with ECoR Station 2.00 700837.00 1401674.00

officials, Only for Subsequent Phase working

not for Initial working.

3 3 Site Acceptance Testing(SAT) with ECoR Station 2.00 723923.00 1447846.00

officials, Only for Subsequent Phase working

not for Initial working.

Schedule A2-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable)

Item- 2 EXECUTION OF SIGNALLING WORKS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Alteration of existing panel,wiring and testing Station 2.00 42357.40 84714.80

and commissioning of Control

Panel[Operation-cum-IndicationConsole] as

per Specn.No.S/36/87 amendment-2,

complete with termination of cable, painting

and lettering asrequired. Railway will

supplyControl Panel and multi core indoor

cables only. Tender shall supply Dominoes,

buttons, keys,counters, MS Angle/Flat,

Hylumsheet, MS clamps, Bolts andnuts, PVC

pipes, Screws,Sleeves, PVC cables, PVC

pipes,PBT terminals, Fuses, LEDs etcand all

other materials requiredfor the work at his

2 2 Alteration of wiring in existing Relay rack/ CT Numbers 6.00 28281.00 169686.00

rack/composite relay rack. This includes

supply of all types of wires, eyelets, nuts &

bolts, bunching material, ferrules, ARA

terminals, fuses & fuse blockes by the

contractor at his own cost. Lettering &

painting to be done by the contractor at his

own cost. Wire (RDSO Approved Sources) to

be inspected by the representative of

Railway before use.

KHURDA ROAD DIVISION-S AND T/ECOR

3 3 Wiring, testing and commissioning of overall Stn/IBH 3.00 140176.00 420528.00

circuits and ground gears of approved

interlocking arrangement as per approved

circuit diagram and Interlocking plan. This

also includes making corrections/alterations

in As Planned drawings and documents as

per the execution at site. This includes Free

home signal connection at site and SM's

office, telephone connection in the

tents/goomties and any other communication

arrangement for the Non interlocking at the

station or as decided by the representative of

Railway during non interlocking. The

materials required for preparation of Free

Home indication board will be supplied by the

tenderer.This also includes painting and

l e t t e r i n g of gears. Telephone , VHF

Sets/Walkie Talkie sets will be supplied by

railway. Note: In case of IBS : It includes

overall testing and commissioning of IBS and

both the end stations associated with IBS

4 4 Miscellaneous arrangement for NI period Station 3.00 149624.00 448872.00

comprising of Provision of water-proof

temporary goomty/tent at both side of the

station yard and at central panel building.

Each goomties to be furnished with one iron

table, six chairs, emergency light and

mosquito repellantcaps for NI staff, PA

system, crowbar men for operating point and

men for supplying water to tents.

5 5 Dismantling of existing LC gates and related Numbers 3.00 10461.00 31383.00

gears.This includes

dismantling,stacking,accountal of all the

materials including transportation of all the

released materials to the Railway store.

6 6 Transportation, excavation of pit, casting of Numbers 20.00 19438.00 388760.00

foundation, plastering and erection of Steel

Apparatus case (full size) with fixing of E-

Type lock, wiring, cable entry, termination

clamping, filling cable pit with sand, painting

and lettering etc., as per Drg.No.

S&T/CON/SK/16. This includes earth work

and/or masonry work required for securing

the apparatus case as per site condition.

Railway will supply apparatus case with 'E'

type lock only from Railway stores at.

Tenderer will supply all wiring materials, PBT

Terminals, fuses, fuse blocks, bus bars, hylum

sheet ISI mark [6mm thickness], wood plank

board of good quality [minimum 3/4" thick,

Cement and transport all the materials to site

of work at his own cost. The wiring materials

such as wire coils, PBT terminals, fuses, fuse

block, etc. should be used from RDSO

approved sources.

7 7 Alteration of wiring in existing apparatus Numbers 20.00 3583.00 71660.00

cases full/half. This includes supply of all

materials in connection with alteration in

wiring. All the materials shall be supplied by

the contractor at his own cost. This includes

entry of cables, sand filling and masonry

work involved. Lettering and painting to be

done by the contractor at his own cost.

Railway shall supply only relays and relay

KHURDA ROAD DIVISION-S AND T/ECOR

8 8 Transportation of signal posts for multiple Numbers 3.00 20931.00 62793.00

aspect colour light signals, complete with

signal units, bases, ladders and other fittings,

excavation of pit, casting of cement concrete

foundation, plastering as per Drg.No

Con/SK/T/12, erection and fixing of complete

fittings of the 2/3/4 aspect signal/signal posts

including termination of cables, wiring, LED

fixing, signal testing and focusing. Name

plate & marker and all other materials shall

be provided by the contractor at his own

cost. Required cement shall be supplied by

the contractor. Arrangement of Screening to

be provided by the contractor if required as

instructed by site Engineer. Contractor shall

prepare jointly with Railway Engineer at site

and submit Signal Sighting report and Signal

test report as per approved format of

Railway. NOTE: (i) 50 % Payment shall be

released after erection of signal post.

Balance 50 % shall be released after

termination of cable, wiring, painting, testing

& focusing of signal. (ii) If foundation is

available at site 30% of the cost is to be

9 9 Laying of Signalling/4 Quad/ 6 Quad/ Power Kilometre 36.50 24389.00 890198.50

Cable/Telecom cables/ Jelly filled cables of all

sizes in excavated trench, through

GI/RCC/DWC pipes etc. wherever required.

This includes transportation of cables from

the stores to work site and transportation of

empty cable drums with left over cables from

site to the stores at . The length of cable laid

includes the length of cable coil for

termination purpose. NOTE: The cables are to

be carefully handled during loading, un-

loading and transportation to work site. Any

damage found in the cable after final testing,

in view of mishandling of cables, shall be

made good by the Tenderer. Cable should be

maggered before and after laying and

recorded in a register and submitted to the

10 10 Excavation of trenches of following depth and Kilometre 5.50 88821.00 488515.50

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

s o i l . This work also includes covering of

c a b l e s l a i d in trench and backfilling,

ramming, consolidation o f s o i l as well as

disposal of extra soil after cable is laid as

specified in Guidelines on Signalling Cable

laying given by RDSO and any latest circular

i s s u e d by CSTE/ECoR/BBS.Note: Before

refilling of the trenches, the cable laid are to

be tested and recorded for its insulation

value and after satisfaction of site Engineer

the refilling process should start and after

monsoon the route is to be attended for

backfilling the rain cuts, wash out of soils

where ever found. [ii] 1.0 Meter

KHURDA ROAD DIVISION-S AND T/ECOR

11 11 Excavation of trenches of following depth and Kilometre 2.00 71060.00 142120.00

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

s o i l . This work also includes covering of

c a b l e s l a i d in trench and backfilling,

ramming, consolidation o f s o i l as well as

disposal of extra soil after cable is laid as

specified in Guidelines on Signalling Cable

laying given by RDSO and any latest circular

i s s u e d by CSTE/ECoR/BBS.Note: Before

refilling of the trenches, the cable laid are to

be tested and recorded for its insulation

value and after satisfaction of site Engineer

the refilling process should start and after

monsoon the route is to be attended for

backfilling the rain cuts, wash out of soils

where ever found. [iii] 0.8 Meter

12 12 Excavation of trenches of following depth and Kilometre 1.00 106669.00 106669.00

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

s o i l . This work also includes covering of

c a b l e s l a i d in trench and backfilling,

ramming, consolidation o f s o i l as well as

disposal of extra soil after cable is laid as

specified in Guidelines on Signalling Cable

laying given by RDSO and any latest circular

i s s u e d by CSTE/ECoR/BBS.Note: Before

refilling of the trenches, the cable laid are to

be tested and recorded for its insulation

value and after satisfaction of site Engineer

the refilling process should start and after

monsoon the route is to be attended for

backfilling the rain cuts, wash out of soils

where ever found. [i] 1.2 Meter

13 13 Fixing of cable route marker as per drawing Numbers 146.00 706.00 103076.00

in" section-H" at a distance of 100 mtrs.

Along the trench and at places where the

cable route has taken diversion as per

instruction of site Engineer, this includes

casting of foundation at site and fixing of the

marker in the foundation made earlier at site

as per railway directives and specifications,

this includes proper curing of the structure,

All materials required for this like cement,

sand 15 mm chips and steel rod of ISI marks

should be supplied by the tenderer.

14 14 Horizontal direction drilling/boring without Metre 1200.00 1515.72 1818864.00

damage of surface of road/track formation.

The bore shall be 150 mm dia. and shall be

at the proper depth as per site conditions

decided by Enginerin-charge. The ground

level shall be considered ignoring the

bankheight of the bank of the road. The

length of the bore shall be minimum 04 Mtrs

long. This include insertion of different dia.

DWC/GI/HDPE pipes coupling etc as per

direction of Engineer-in-charge. NOTE: The

cost of pipe is not included in this item.

Contractor shall provide all material required

for boring and adequate nos. of labourers for

proper laying of cables in to the bore. Cable

shall be laid cautiously so that it should not

get damage due to rough handling and

pressure on cable.

KHURDA ROAD DIVISION-S AND T/ECOR

15 15 Excavation of trenches in all kinds of soils Metre 290.00 335.00 97150.00

including soft rocky area and clearing of

track etc. to a depth of 1.0 M and width of

0.3 M for track crossing /pucca road/level

crossing gate/platform/station circulating

area or any other place as advised by site

Engineer including transportation and laying

of DWC/RCC/Split RCC/G.I. pipes with or

without coupler. This includes repairing of

track/pucca road/level crossing gate/

platform/station circulating area surface to

original position by ramming and concreting

wherever required soon after the work is

over. DWC/RCC/GI pipes shall be supplied by

the Railway. DWC pipes wherever required

shall be supplied in 6 Mtr. length and shall be

cut to size as per requirement. All other

materials including cement are to be supplied

by the contractor.

16 16 Excavation of trenches including clearing of Metre 660.00 255.00 168300.00

roots of trees etc., in rocky area up to a

depth to be indicated byRailway Engineer at

site as per the site condition [Minimum 0.6

meter] and width 0.3 Mts. at the bottom. This

includes concreting &plastering as per the

instructions of site Engineer andcomplete

backfilling by digging earth from a lead of 30

Mtr. In case 0.8 meter depth or higher is

achieved no concreting is required, otherwise

concreting up to 100 mm thickness should be

done. All materials required for the above

works shall be supplied by the Contractor.

17 17 Cable Duct behind the Relay room and Numbers 6.00 16729.00 100374.00

Goomties of size 1.8 M x1.8 M x 1.2 M to

keep cables entering into it consisting of

brick work of 254 mm thickness of proportion

1:6 with sand filling after coiling of cables.

The top of sand filling covered with

concreting of size 1.30 M x1.30 M and a

depth of 200 mm of proportion 1 :1.5 : 3

outside of the duct should be plastered with

cement mortar 1 : 6 to achieve smooth

finishing. All materials including cement and

chips of size 40mm. and second class bricks

etc. to be supplied by the contractor.

18 18 Cutting of masonary floor/walls at station Numbers 6.00 6108.00 36648.00

building/ signalgoomty/ Gate lodge at a

depth of 0.5 mtr. to 1.0 mtr a t places to be

indicated by site Engineer for entering of

cables inside the building. Only G.I pipes

supplied by Railway and all materials as

clamps, bolts & nuts as instructed by site

Engineer supplied by tenderer. This includes

repairing of masonary floors/walls after the

cables are taken inside. Cement, Sand

required for the work shall be supplied by the

tenderer and also transportation of G.I Pipe

from Store by the tenderer.

KHURDA ROAD DIVISION-S AND T/ECOR

19 19 Trenching and fixing of G.I. pipes of different Metre 110.00 533.00 58630.00

sizes/DWC pipes in hard rocky area up to a

depth of 0.3 M to 0.6 M or at places as per

instructionof site Engineer and concreting [1

:3 : 6] up to height of 100 mm above the

pipes. G.I. pipes with the socket/ DWC pipes

shall be supplied by the Railway. All other

materials required for the works shall be

supplied by the contractor. Note: [1] In case

of girder bridges, G.I. pipes shall be suitably

clamped by the contractor as advised by the

site Engineer. Clamps shall be supplied by

the contractor. [2] The work including

excavation of trenches in hard rock area up

to a depth of 0.3 M to 0.6 M and back filling,

ramming after completion of work where

ever required. [3] In case of concrete bridges

clearing of ballast for laying of pipes and re

arranging the Railway ballast after

completion of work shall be done by the

20 20 Supply, Transportation and Installation of Numbers 30.00 12306.00 369180.00

earth electrode (make TATA or Jindal as per

Rly. practice) including MS flat for signalling

equipments on lever frame, apparatus cases,

signal, relay racks, cable termination rack,

block instrument etc. (supply & installation of

earth electrode as per drawing no.

RE/S&T/DRG/Tender/SK/398/94 for apparatus

cases, signal post & other equipments as per

instruction on earthing of S&T equipment.

Laying of earth lead mild steel flat of size

35mmx6mm and fixing of lead MS flat (make

TATA/Jindal or Similar) to earth electrode and

lever frame, signal post & apparatus cases as

per Drg. No. CORE/S&T/ALD/SK/591/2008,

592/2008 and 593/2008 respectively and

instructions on earthing at S&T equipment

and providing cement enclosure for earth

electrode as per drawing no.

RE/S&T/Sig./Tender/SK/13/85 Alt. A) NOTE:

This includes testing of earth value and

indicating the same on the Earth enclosure

by paint. Inspection by representative of

21 21 Supply, installation, testing and Numbers 8.00 61717.00 493736.00

commissioning of Maintenance free and

permanent earth as per RDSO Specification

No. RDSO/SPN/197 Version 1.0 and Technical

Specification as per section H, Chapter 8,

Inspection by RDSO.

22 22 Fixing of relay bases and wiring, bunching, Per Relay 100.00 783.00 78300.00

fixing of relays, wiring in Old relay

racks/location box and also carrying out any

alteration in existing relay rack duly wiring

and connecting New to old and Old to old

relays by standard wires (RDSO Approved

Sources) as per Circuit diagram. Fuses of

bases, condensers, ND fuses, LED indicator &

its wiring for relay rack. All materials required

for this work will be supplied by the

contractor from RDSO Approved Sources.

Relays with accessories will be supplied by

KHURDA ROAD DIVISION-S AND T/ECOR

23 23 Hiring of JCB machine (in good condition) for Hour 62.00 845.61 52427.82

levelling and dressing ground/dismantling

structures including disposal of debris

through dumpers etc. with contractor's

labour, JCB machine, machine operator, fuel

etc. The contractor shall arrange road permit

for vehicle for all the states of operation as

per instruction of engineer-incharge and

vehicle shall not be more than three years

old. payment shall be made for actual

working hours at site.

24 24 Supply, fitting & fixing of ply board 19mm Sqm 220.00 1684.47 370583.40

thick for cupboard, partition wall etc.

Inspection by representative of Sr.DSTE/KUR.

25 25 Transportation of OFC from the store of to Kilometre 3.00 25563.00 76689.00

work site with care, and pushing/ pulling OFC

through the HDPE pipes sealing of the duct

by simple plugs. The cable is to be laid by

mechanised means. At inaccessible places

where mechanised laying is not possible, the

cable is to be laid manually by pulling

through pre inserted rope. Empty cable

drums with or without leftover cable should

be returned to the store. This also includes

testing of cable drums by OTDR in the store

premises before transportation and

submission of results thereof.

26 26 Transportation of HDPE pipe from the store to Kilometre 3.00 15746.00 47238.00

the work site, laying of the same ( with 4mm

nylon rope,pre inserted inside the HDPE pipe)

in excavated trench/already laid GI/RCC

pipe/tubes,jointing, levelling and end sealing

the pipes. HDPE pipe, couplers and end rope

shall be supplied by the railways, Nylon rope

shall be supplied by the contractor.

27 27 Transportation and jointing (straight through Numbers 32.00 1591.00 50912.00

and derivation) of PIJF/quad cables size TSF-

IV as per Specn No. IRS: TC-31/96 & IRS

30/97. Jointing kits shall be supplied by the

Railway. All other materials shall be supplied

by the tenderer.

28 28 Supply, transportation, and installation of Numbers 14.00 11156.00 156184.00

RCC joint chamber with two piece top cover

and bottom cover with hole for drainage and

cable entry as per drawing No.RCIL/ER/DRG-

02/06 (Section-H). This includes trenching for

joint pit, back filling and ramming of pit after

placing the joint closure and cable loop in the

chamber without causing damage to the

same and consolidation of soilas well as

disposal of excess soil. Inspection by

representative of Sr.DSTE/KUR.

29 29 Supply ,transportation& installation of Optical Numbers 12.00 18027.00 216324.00

Fibre cable joint enclosure and splicing of

OFC (24 Fibre) and testing. OFC splicing shall

be done in presence of Railway

Representative.

KHURDA ROAD DIVISION-S AND T/ECOR

30 30 Transportation, excavation of pit, casting of Numbers 12.00 9742.00 116904.00

foundation, plastering and erection of Steel

Apparatus case (Half size) with fixing of E-

Type lock, wiring, cable entry, termination

clamping, filling cable pit with sand, painting

and lettering etc., as per Drg.No.

S&T/Con/BBS/92/90. This includes earth work

and/or masonry work required for securing

the apparatus case as per site condition.

Railway will supply apparatus case with 'E'

type lock only. Tenderer shall supply all

wiring materials, PBT Terminals, fuses, fuse

blocks, bus bars, hylum sheet ISI mark [6mm

thickness], wood plank board of good quality

[minimum 3/4" thick, cement and any other

materials that are required for the work at his

own cost. Contractor has to transport all the

materials from store at his own cost to the

work site. The wiring materials such as wire

coils, PBT terminals, fuses, fuse block, etc.

should be used from RDSO approved sources.

1) Modification of inside arrangement of

Apparatus cases if required for fixing of

relays/transformers etc. shall be done by the

contractor. Extra shelf, if any, shall be

deposited to the Railway stores by the

contractor. 2) All cables shall be terminated

by providing copper eyelet of suitable size.

Note:-(i) If location box foundation is

available at site 20% of the cost is to be

deducted.(ii) 40% payment shall be released

after erection of location boxes.

31 31 Submission of the final cable route plan after Route 1.70 2111.00 3588.70

the cables are laid and commissioned Kilo

indicating clearly the exact position of the Meter

cable, joints, LB for emergency sockets and (RKM)

other critical materials with reference so

centre line of the nearest track. The final

cable route plan and drawings of the cable

terminations along with all relevant

particulars area to be submitted to the

Railways in original master form as well as 6

32 32 Hiring charges for 7.5 KVA DG Set including Job 6.00 1945.63 11673.78

manpower for operation and maintenance as

per direction of Engineer at site. Only HSD oil

is to be supplied by Railway. Remaining all

other materials including transportation of

the DG set to the site is to be borne by the

contractor. (1 JOB=1 DG set for 1 day)

commissioning & associated wiring for

temporary lighting with 1x28 Watt T5

FL/1X18 W or abo ve indoor type LED T8

fittings with lamp including manpower for

operation and maintenance as per direction

of Engineer at site. All materials including

fitting & wires etc. are to borne by the

contractor. (1 JOB= 1 Light for 1 day).

KHURDA ROAD DIVISION-S AND T/ECOR

34 34 Supply, transportation, erection, and grouting Numbers 6.00 96053.00 576318.00

of Composite Relay Racks / Relay Racks / CT

racks as per Drg.No. SK/DRG/OL/SER/192, SH-

1/2 (for Composite Relay Racks), Drg.No.

SK/DRG/OL/SER/192, SH-2/2 (for Relay Racks)

and Drg.No. S&T/CON/HQ/VSKP/95/92 (for CT

Racks) respectively, including fixing of racks,

PBT terminals 1-Way/6-Way, ND Fuses, Bus

Bars, Eyelets, Hylum strips of required

thickness [12 mm] as per length required at

site, condensers and resistances etc.,

wherever required as per directions of Site

Engineer. Inspection of Composite Racks /

Relay racks/CT racks by Representative of

Railway before use. Tenderer shall supply all

the materials from RDSO approved sources

such as PBT terminals 1-Way/6-Way, ND

Fuses, Fuse blocks, Bus Bars, Eyelets, Hylum

strips (12 mm thicknessn ISI Mark)

condensers and resistances etc., and any

other materials required for the work at his

own cost. Inspection by RITES.

35 35 Wiring and testing of complete Relay Rack / Numbers 6.00 158351.00 950106.00

CT Rack / Composite Relay Rack as per

wiring diagram for maximum number of plug

in type relay & shelf type relays of different

sizes or as directed by Railway Engineers at

site. This includes rack to rack wiring through

MS ladder fixed on the top of the relay rack,

crimping eyelets in the terminals fitted in the

cables termination rack, numbering by

ferrules 2.5 sq. mm, bunching of wires by

bunching Tape/Thread and buttons, painting

and lettering as required. Wiring of the racks

shall be done with PVC wire of size 16/0.2

mm and 3/0.75 mm. Tenderer shall supply all

wires & wiring materials purchased from

RDSO approved sources. Note: 1) Only relay

and relay bases will be supplied by the

Railway. Contractor has to supply all other

materials for the above work and make

arrangement for transportation of materials

supplied by Railway at his own cost. 2) Only

brass screws shall be used for fixing of relay

bases. 3) All types of wires and wiring

materials, eyelets of sizes (make: Dowell's or

similar), ferrules (2.5 sq.mm), resin core

solder, insulating tape, bunching belt &

buttons etc. are to be supplied by the

contractor. Wires will be procured from RDSO

approved sources only. and all other

components will be supplied by the

contractor as per requirement at site.

36 36 Shifting & adjustment of existing analog axle Numbers 6.00 103670.00 622020.00

counters/SSDAC as per the instruction of the

Railway representative.

KHURDA ROAD DIVISION-S AND T/ECOR

37 37 Transportation and fixing of perforated G.I. Metre 36.00 2653.00 95508.00

Pipes on bridges, culverts, drains or in

trenches or any other place as per instruction

of site Engineer with clamps at 1.5 mts.

interval on steel girder bridges or at places

advised by site Engineer. This includes

supplying of G.I. Pipes, 80/100/150 mm dia.

Specn. No. IS:1239/2004, or latest medium

gauge with threaded collars (Make -TATA

/JINDAL) by tenderer. This also includes 100

mm thick concreting on GI pipes as required

and instructed by site Engineer and all other

materials required for the work shall be

supplied by the tenderer. Note: The G.I. pipe

shall be perforated by drilling 7 mm dia holes

length wise in zig-zag manner staggered at a

distance of 300 mm. G.I. Pipes before and

after perforation and bridge fixtures supplied

by the tenderer will be inspected by

representative of Railway before use. The

bridge fixtures will be supplied by tenderer

for fixing of GI pipes on girder bridges only.

(ii) GI pipes of 100 mm Dia;

38 38 Painting, varnishing, numbering, lettering Station 1.00 38057.00 38057.00

and graphiting of all outdoor and indoor

signallingequipments over and above the

initial painting as per instruction of Railway

representative at site. This includes supply of

paints, varnish, graphites and any other

consumables by the contractor.

Schedule B1-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable)

Item- 3 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of Steel Apparatus case 'large Size' as Numbers 20.00 42507.00 850140.00

per Drg. No - CON/SK/1/1/86 and Spec.No.

IRS:S-10/78 (adv) with latest amnd. with "E"

type lock and key of ward No-32 with handle.

Inspection by RITES.

2 2 Supply of 4.6 Mts CLS tubular steel post Numbers 3.00 11663.00 34989.00

specification No. IRS: S-6/81 with latest Amnd

to suit 140 mm dia base. Inspection by the

3 3 Supply of Signal Base 140 mm dia [Type Numbers 3.00 5024.00 15072.00

tube] Drg. No. S-2011/M. Inspection by the

4 4 Supply of double walled corrugated pipe 6 Numbers 50.00 4117.00 205850.00

mtr in length, 120 mm outer dia and 103 mm

inner dia, w i t h one suitable coupler

conforming to RDSO Specification No.

RDSO/SPN/204/2011 Version 1.1 Amdt 1 or

latest for under ground cable protection

.Colour-Orange. Inspection by representative

of Sr.DSTE/KUR. Note: If required, the DWC

pipe shall be supplied split in two halves;

5 5 Supply of Perforated G.I. pipe of 100 mm dia Metre 110.00 1889.00 207790.00

with socket. G.I. pipe of make TATA/JINDAL

shall be as per IS: 1239 part-I/2004

Specification for medium gauge and shall be

perforated by drilling 7 mm dia holes length

wise in zig-zag manner staggered at a

distance of 300 mm. Inspection by

representative of Sr.DSTE/KUR.

KHURDA ROAD DIVISION-S AND T/ECOR

6 6 Supply of Digital multimeter Fluke-287 or Numbers 1.00 114234.00 114234.00

latest higher version with testing lead

complete with case and spare set of

batteries.Inspection by representative of

7 7 Supply of cable route tracer with Integrated Numbers 3.00 451828.60 1355485.80

GPS and Bluetooth, Live GPS data transfer

with Mobile App, through BT, User

configurable frequency and Current direction

indication & 10W Transmitter with minimum

500mA output current and 90V visible on

display, with rechargeable Battery.

Specification as per section H. Make:

adiodetection (RD8200G) or similar. 3 years

OEM warranty. INSPECTION BY RITES.

8 8 Supply of Insulation resistance tester 500V Numbers 3.00 17857.00 53571.00

DC 500 Mega Ohms hand generator type

metal body to Spec. no. IS:2992 make

WACO.Inspection by representative of

9 9 Supply of AC/DC Digital clamp meter Fluke- Numbers 2.00 83661.00 167322.00

376 or similar.Inspection by representative of

10 10 Supply of Permanently lubricated two layer Kilometre 3.00 132496.00 397488.00

type HDPE duct, outer dia 40 mm, inner dia

33 mm with three end plugs and two

couplers for every Km length of pipe in

length of 500 m confirming to RDSO Spec.

No. RDSO/SPN/TC/45/2013.Rev.2.0

Amendment 2.0 or latest. Inspection by

RITES. Note: The HDPE Duct should be pre

inserted with 4 mm nylon rope, inside the

11 11 Supply of Thermo shrink jointing kit for Numbers 26.00 6143.00 159718.00

underground cable as per Specn No. IRS: TC-

77/2012 [Rev.3] Amd 3. (Cable jointing kit

shall be procured from RDSO approved

sources only). Inspection by RDSO.

12 12 Supply of Steel Apparatus case 'Half Size' as Numbers 12.00 25868.00 310416.00

per rg.No.S&T/CON/BBS/92/90 with 'E' type

lock & Key. Ward No. 32. Inspection by RITES

13 13 Supply of Hand Held 200 Khz Digital Numbers 4.00 40592.00 162368.00

Multimeter . MAKE- FLUKE/ YOKOWAGA

.MakeiBrand:- FLUKE 87V. Inspection by

representative of Sr.DSTE/KUR.

14 14 Supply of Signal colour light multi unit as per Numbers 3.00 19082.00 57246.00

specification No: IRS: S-26/64 with latest

amendment as per RDSO Spec No.

RDSO/SPN/153/2011 long range working on

110 V- AC 50 Hz complete 2-Aspect suitable

for 140 mm dia. post as per Drg.No:SA-23003

A/M [Adv]. Inspection by the RITES.

15 15 Supply of Ladder 4.5 meter for CLS post as Numbers 3.00 5745.00 17235.00

per Drg. No. SA: 23150 [Adv] Alt-1,

specification No. IRS: S-10/78 (with latest

Amendment) consisting of ladder base,

platform and guarding, ladder support

complete. Inspection by the RITES.

16 16 Supply of Insulated flexible wirerope steel Kg 500.00 411.87 205935.00

galvanized 7 X 7 strands.Inspection by

representative of Sr.DSTE/KUR.

17 17 Supply of optical fibre joint closure for Numbers 4.00 5669.00 22676.00

straight through joint with modification for 24

fibre as per RDSO Specn No.

RDSO/SPN/TC/68/2014, Revision 0.1 Amnd. 1

or latest.Inspection by representative of

KHURDA ROAD DIVISION-S AND T/ECOR

Schedule B2-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

Schedule 4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item Directory - Not

Item- 4 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of Relay AC Immune, plug-in type, Numbers 40.00 6428.00 257120.00

style 'QNA1', Neutral line, 24V DC 8F/8B

contacts, Front and back contacts metal to

carbon, complete with plug board, retaining

clip and connectors conforming to

BRS:931A,IRS : S - 60, IRS : S - 34, IRS : S - 23

(As applicable). Interlocking code : ABDGH.

Inspection by RDSO.

2 2 Relay plug in type, Style AC-LED: ALL aspect, Numbers 10.00 7878.00 78780.00

AC lamp proving Relay unit within built

current transformer type, slow release

neutral line relay, 4F/4B contact , front and

back contact metal to carbon shall be

suitable for working in series with 110V AC,

LED signal lamp rated at 15W conforming to

RDSO Spec No- STS/E/Relay/AC lit

LED/signal/09-2002, Amdt. 1, BRS : 941A ,IRS

: S :3 4 &IRS :S : 23 {as applicable}. The

interlocking code for this unit shall be

ABDHK. Inspection by RDSO.

Schedule B3-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

Schedule 4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item Directory - Not

Applicable) (Item Directory - Not Applicable)

Item- 5 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of LED signal lamps RED aspect for Numbers 5.00 8401.60 42008.00

main color light signals for railway signaling

as per RDSO.( Warranty Period :Upto 60

months from the date of supply). Inspection

2 2 Supply of Integrated LED Signal for YELLOW Numbers 5.00 8401.60 42008.00

aspect as per RDSO Specification No.

RDSO/SPN/199/2010Rev1.1 or latest. (

WarrantyPeriod :Upto 60 months from the

date of supply). Inspection by RDSO.

3 3 Supply of Integrated LED Signal for GREEN Numbers 5.00 9581.60 47908.00

aspect as per RDSO Specification No.

RDSO/SPN/199/2010Rev1.1 or latest. (

WarrantyPeriod :Upto 60 months from the

date of supply). Inspection by RDSO.

Schedule C -SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE INCLUSIVE OF:1.All taxes.,

2.Supply of sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of

Schedule materials to site., 4.Transportation of released materials from one site to another site or store of

concerned SSES/(In-charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item

Directory - Not Applicable) (Item Directory - Not Applicable)

Item- 6 SUPPLY & EXECUTION OF DRAWING WORK

S No. Item Description of Item Unit Qty Rate Amount

1 1 Compilation, preparation, correction, Per Page 300.00 25.00 7500.00

updating, printing and supply of Final station

working rules with contractor's stationery,

tools, plants and materials. Note: Final SWR

to be submitted in 2 sets for each station.

KHURDA ROAD DIVISION-S AND T/ECOR

2 2 Printing and supply of approved SWR with Per Page 500.00 4.00 2000.00

contractor's stationery, tools, plants and

materials. Note: Approved SWR to be

submitted in 6 copies for each station.

3 3 Compilation, preparation, printing, binding Per Page 100.00 25.00 2500.00

and supply of Draft station/Gate working

rules both in English and Hindi using MS word

software in computer on the basis of WRD,

RCC and Front plate diagram of Panel/VDU

with contractor's stationery, tools, plants &

4 4 Design of SIP & submission of Three paper Set 1.00 36520.00 36520.00

copies for approval.For a Four-Line Station

5 5 Design of SIP & submission of Three paper Set 1.00 76591.00 76591.00

copies for approval.For a Six-Line Station

6 6 Design of SIP & submission of Three paper Set 1.00 97667.00 97667.00

copies for approval. For a Eight-Line Station

7 7 Design of SWRD & submission of Three paper Set 1.00 17628.00 17628.00

copies for approval.For a Four-Line Station

8 8 Design of SWRD & submission of Three paper Set 1.00 36472.00 36472.00

copies for approval.For a six-Line Station

9 9 Design of SWRD & submission of Three paper Set 1.00 43015.00 43015.00

copies for approval. For a Eight-Line Station

10 10 Design of Cable Route Plan (Distant to Set 1.00 8815.00 8815.00

Distant) & submission of Three paper copies

for approval. For a Four-Line Station

11 11 Design of Cable Route Plan (Distant to Set 1.00 24619.00 24619.00

Distant) & submission of Three paper copies

for approval. For a six-Line Station

12 12 Design of Cable Route Plan (Distant to Set 1.00 29286.00 29286.00

Distant) & submission of Three paper copies

for approval. For a Eight-Line Station or more.

13 13 Supply of Original Tracing of SIP after Numbers 1.00 730.00 730.00

incorporating all the corrections. For a Four-

14 14 Supply of Original Tracing of SIP after Numbers 1.00 866.00 866.00

incorporating all the corrections. For a Six-

15 15 Supply of Original Tracing of SIP after Numbers 1.00 1013.00 1013.00

incorporating all the corrections.Fora Eight-

Line Station or more.

16 16 Supply of Original Tracing of SWRD after Numbers 1.00 528.00 528.00

incorporating all the corrections. For a Four-

17 17 Supply of Original Tracing of SWRD after Numbers 1.00 729.00 729.00

incorporating all the corrections. For a Six-

18 18 Supply of Original Tracing of SWRD after Numbers 1.00 916.00 916.00

incorporating all the corrections. For a Eight-

Line Station or more.

19 19 Supply of Original Tracing of Cable Route Numbers 1.00 1411.00 1411.00

Plan (Distant to Distant) after incorporating

all the corrections. For a Four-Line Station

20 20 Supply of Original Tracing of Cable Route Numbers 1.00 1752.00 1752.00

Plan (Distant to Distant) after incorporating

all the corrections. For a Six-Line Station

21 21 Supply of Original Tracing of Cable Route Numbers 1.00 1977.00 1977.00

Plan (Distant to Distant) after incorporating

all the corrections. For a Eight-Line Station or

22 22 Supply of Original Tracing of Location Box Station 1.00 2644.00 2644.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Four-Line Station

KHURDA ROAD DIVISION-S AND T/ECOR

23 23 Supply of Original Tracing of Location Box Station 1.00 3647.00 3647.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Six-Line Station

24 24 Supply of Original Tracing of Location Box Station 1.00 5491.00 5491.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Eight-Line Station or more.

25 25 Supply of Amonia Print of Approved SIP .For a Numbers 6.00 44.00 264.00

Four-Line Station

26 26 Supply of Amonia Print of Approved SIP .For a Numbers 6.00 46.00 276.00

Six-Line Station

27 27 Supply of Amonia Print of Approved SIP . For Numbers 6.00 46.00 276.00

a Eight-Line Station or more.

28 28 Supply of Amonia Print of Approved Numbers 11.00 44.00 484.00

SWRD.For a Four-Line Station

29 29 Supply of Amonia Print of Approved Numbers 11.00 46.00 506.00

SWRD.For a Six-Line Station

30 30 Supply of Amonia Print of Approved SWRD. Numbers 11.00 46.00 506.00

For a Eight-Line Station or more.

31 31 Supply of Amonia Print of Approved Cable Numbers 6.00 44.00 264.00

Route Plan(Distant to Distant). For a Four-

32 32 Supply of Amonia Print of Approved Cable Numbers 11.00 46.00 506.00

Route Plan(Distant to Distant). For a Eight-

Line Station or more.

33 33 Supply of Amonia Print of Approved Cable Numbers 11.00 46.00 506.00

Route Plan(Distant to Distant). For a Six-Line

Station or more.

34 34 Supply of Amonia Print of Approved Cable Station 6.00 46.00 276.00

Route Plan(mid section). For a Six-Line

35 35 Design of RCC & submission of Three paper Set 1.00 17628.00 17628.00

copies for approval.For a Four-Line Station

36 36 Supply of Original Tracing of RCC after Numbers 1.00 705.00 705.00

incorporating all the corrections. For a Four-

37 37 Supply of Amonia Print of Approved RCC. For Numbers 6.00 44.00 264.00

a Four-Line Station

38 38 Alteration of Existing Circuit Diagrams Sheet 450.00 350.00 157500.00

consisting of the items as mentioned below &

submission of Three paper copies for

approval. (i) Wiring Diagrams, (ii) Relay

Disposition Charts, (iii ) Contact Analysis and

Fuse Particulars, (iv) Panel Termination

Chart, (v) CT Rack Particulars & (vi) Input &

Output Bit Chart for EI Systems

39 39 Design of Cable Distribution Plan & Set 1.00 16589.00 16589.00

submission of Three paper copies for

approval. For a Six -Line Station

40 40 Design of Cable Distribution Plan & Set 1.00 23562.00 23562.00

submission of Three paper copies for

approval.Fora Eight-Line Station or more.

41 41 Supply of Original Tracing of Cable Numbers 1.00 1411.00 1411.00

Distribution Plan after incorporating all the

corrections. For a Four-Line Station

42 42 Supply of Original Tracing of Cable Numbers 1.00 1752.00 1752.00

Distribution Plan after incorporating all the

corrections. For a Six-Line Station

43 43 Supply of Original Tracing of Cable Numbers 1.00 1977.00 1977.00

Distribution Plan after incorporating all the

corrections. For a Four-Line Station

KHURDA ROAD DIVISION-S AND T/ECOR

44 44 Supply of Original Tracing of Goomty Station 2.00 3878.00 7756.00

Drawings (Including Relay Disposition Chart,

Contact Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc) after

incorporating all the corrections. For a Four-

45 45 Supply of Amonia Print of Approved Circuit Station 2.00 4583.00 9166.00

Diagrams consisting of the items as

mentioned below. (i) Wiring Diagrams, (ii)

Relay Disposition Charts, (iii ) Contact

Analysis and Fuse Particulars, (iv) Panel

Termination Chart & (v) CT Rack Particulars.

For a Four-Line Station

46 46 Supply of Amonia Print of Approved Station 2.00 705.00 1410.00

G o o m t y D r a w i n g s ((Including Relay

Disposition Chart, Contact Analysis, Fuse

Particulars, CT Rack Particulars and Floor

Plan etc). For a Four-Line Station

47 47 Supply of Amonia Print of Approved Station 1.00 1464.00 1464.00

G o o m t y D r a w i n g s ((Including Relay

Disposition Chart, Contact Analysis, Fuse

Particulars, CT Rack Particulars and Floor

Plan etc). For a Eight-Line Station or more.

48 48 Alteration of Existing Location Box Drawings Sheet 160.00 451.00 72160.00

(Including Contact Analysis, Fuse Particulars

etc) and submission of Three paper copies for

49 49 Alteration of Existing GoomtyDrawings Sheet 46.00 901.00 41446.00

(Including Relay Disposition Chart, Contact

Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc) and

submission of Three paper copies for

50 50 Supply of Original Tracing in A-3 Size. NOTE:- Sheet 650.00 71.00 46150.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size.

51 51 Supply of Amonia Prints in A-3 Size. NOTE:- Sheet 1850.00 19.00 35150.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size.

52 52 Design of Location Box Drawings (Including Station 1.00 1763.00 1763.00

Contact Analysis, Fuse Particulars etc) and

submission of Three paper copies for

approval. For a Four-Line Station.

53 53 Design of Location Box Drawings (Including Station 1.00 2735.00 2735.00

Contact Analysis, Fuse Particulars etc) and

submission of Three paper copies for

approval. For a Six-Line Station.

54 54 Design of Location Box Drawings (Including Station 1.00 3661.00 3661.00

Contact Analysis, Fuse Particulars etc) and

submission of Three paper copies for

approval. For a Eight-Line Station or more.

55 55 Supply of Amonia Print of Approved Cable Numbers 6.00 44.00 264.00

Distribution Plan. For a Four-Line Station.

56 56 Supply of Amonia Print of Approved Cable Numbers 6.00 46.00 276.00

Distribution Plan.Fora Eight-Line Station or

57 57 Supply of Amonia Print of Approved Cable Numbers 6.00 46.00 276.00

Distribution Plan.For a Six-Line Station or

58 58 Supply of Original Tracing of Circuit Diagrams Station 1.00 26442.00 26442.00

consisting of the items as mentioned below

after incorporating all the corrections. (i)

Wiring Diagrams, (ii) Relay Disposition

Charts, (iii ) Contact Analysis and Fuse

Particulars, (iv) Panel Termination Chart, (v)

CT Rack Particulars & (vi) Input & Output Bit

Chart for EI Systems. For a Four-Line Station

KHURDA ROAD DIVISION-S AND T/ECOR

59 59 Supply of Original Tracing of Circuit Diagrams Station 1.00 33736.00 33736.00

consisting of the items as mentioned below

after incorporating all the corrections. (i)

Wiring Diagrams, (ii) Relay Disposition

Charts, (iii ) Contact Analysis and Fuse

Particulars, (iv) Panel Termination Chart, (v)

CT Rack Particulars & (vi) Input & Output Bit

Chart for EI Systems. For a Six-Line Station

60 60 Supply of Original Tracing of Circuit Diagrams Station 1.00 41184.00 41184.00

consisting of the items as mentioned below

after incorporating all the corrections. (i)

Wiring Diagrams, (ii) Relay Disposition

Charts, (iii ) Contact Analysis and Fuse

Particulars, (iv) Panel Termination Chart, (v)

CT Rack Particulars, (vi) Input & Output Bit

Chart for EI Systems. For a Eight-Line Station

submission of Three paper copies for

approval, For a Six-Line Station

62 62 Design of Track Bonding Plan & submission of Set 1.00 6699.00 6699.00

Three paper copies for approval. For a Four-

63 63 Design of Circuit Diagrams consisting of the Station 1.00 132211.00 132211.00

items as mentioned below & submission of

Three paper copies for approval. (i) Wiring

Diagrams, (ii) Relay Disposition Charts, (iii )

Contact Analysis and Fuse Particulars, (iv)

Panel Termination Chart, (v) CT Rack

Particulars & (vi) Input & Output Bit Chart for

EI Systems. For a Four-Line Station

64 64 Design of Goomty Drawings (Including Relay Station 1.00 3525.00 3525.00

Disposition Chart, Contact Analysis, Fuse

Particulars, CT Rack Particulars and Floor

P l a n etc) and submission of Three paper

copies for approval, For a Four-Line Station.