CONSTRUCTION OF CANTEEN, MESS and STUDENT ACTIVITY CENTER AT J.C.BOSE UST, FARIDABAD.

Amount

Providing and injection chemical emulsion for pre-constructional anti termite treatment using inside a cloprid 0.075% concentration and creating a chemical barrier under and around the coloumn pits, wall trenches, basement excavation, top surface of plinth filling junction of wall and floor, along with the external perimeter of building, expansion joints surrounding of pipes and conduit etc., complete (Plinth area of the building at ground floor only shall be measured) (N.S. ITEM)

Earth Filling under floors with Tibba sand taken from outside the campus area with all lead & lift, including loading, unloading, laid in 15 cm layers including ramming, watering compensation of earth etc. complete in all respect (N.S.ITEM) complete in all respect.

Providing and laying Water proofing with Tapecrete-P-151 slurry over prepared concrete surface with Fiber Glass fabric on to wet slurry and application with one coat of Polymer modified cementatious brush topping and second coating of Tapecrete-P-151 slurry coating. complete in all respect. (N.S.ITEM) (For Toilets & Kithens only)

Providing and fixing galvanized chicken wire mesh (24 gauge 12 mm size) to junctions of concrete and masonry work and other locations including cutting to required sizes, side laps of minimum 75 mm and fixing in position with galvanized iron wire nails, complete in all respect. (N.S.ITEM)

Providing and fixing solid laminated flush door shutters having uniform thickness of 37mm with smooth finish and moisture content 10 to 12% with water absorption of 2%, climate stable, warp and bend free as certified by IS-2202 with 1mm HPL conforming to IS - 2046 including , screws chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position).(Greenlam, century , Merino make) (N.S ITEM).

Supplying of 15mm to 18mm thick slab of pre polished granite stone as specified as per sample approved by the Engineer In charge. Note 1. Laying of granite will be paid under item no HSR(14.95) & (14.96 ) 2. Measurement shall be maid as per finished floor/wall etc on actual basis.

Leather brown

Jet-black ( without spots)

Paradisso

Cheema Pink

Providing and fixing commercial type block board (Duro, Green or Centurymake or equivalent with prior approval of Engineerin charge ), duly fixed with 1 mm thick laminate (Merino, Greenlam or Century make) on both sides with plain lining, butt joint, including margin (25mm X 3mm) complete with necessary nails. (25 mm thick ) (N.S)

Providing and fixing commercial type block board (Duro, Green Or Century make or equivalent with prior approval of Engineerin charge ) duly fixed with 1 mm thick laminate (Merino, Greenlam or Century make) on both sides with plain lining, butt joint, including margin (19mm X 3mm) complete with necessary nails. (19 mm thick ) (N.S)

Providing and Fixing SS ball bearing hinge (4 x 3 x 3mm) - Godrej or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing Tower bolt 12" Aluminium - Godrej or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing Tower bolt 6" Aluminium - Godrej or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing SS finish door stopper - Model Godrej or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing SS back stopper - Model Godrej or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing NEH 03 Pull handle - Model Godrej or equivalent make as per prior approval of Engineer-in-Charge.

HW for Cupboard Providing and Fixing Click-on Hinge overlay - Model HC-1(I) of Ebco or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing Click-on hinge half overlay - Model HC-2(I) of Ebco or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing Handle 96mm (Zinc) - Model AZH 96 of Ebco or equivalent make as per prior approval of Engineer-in-Charge. .

Providing and Fixing Handle 224mm (zinc) - Model AZH-225 of Ebco or equivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing Magnet Catcher ultra slim - Model MCUS-2L of Ebco orequivalent make as per prior approval of Engineer-in-Charge.

Providing and Fixing Tower Bolt Cranked (6") Model LC150 of Ebco or equivalent make as per prior approval of Engineer-in-Charge.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, TPV / EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners,

mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Kommerling, Fenesta & Deceuninck Make)

Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 58 x 52 mm, sash 58 x 68 mm & mullion 58 x 68 mm all having wall thickness of 2.2 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 1.25 sqm upto 1.50 sqm). (Kommerling, Fenesta & Deceuninck Make)

Casement window double panels with coupling Center fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 58 x 52 mm, sash 58 x 68 mm & mullion 58 x 68 mm all having wall thickness of 2.2 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window above 2.0 sqm upto 3.0 sqm). (Kommerling, Fenesta & Deceuninck Make)

Providing and fixing factory made uPVC white colour tophung cum fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, TPV / EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc.

After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Kommerling, Fenesta & Deceuninck Make)

Tophung cum fixed window / ventilator made of (small series) frame 58 x 52 mm & sash & mullion 58 x 68 mm both having wall thickness of 2.2 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) (Kommerling, Fenesta & Deceuninck Make)

Fixed window with two part made of (Big series) frame 58 x 69 mm joint with coupling having wall thickness of 2.2 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 3.75 sqm upto 4.25 sqm. (Kommerling, Fenesta & Deceuninck Make)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.20 m in height dimension comprising of uPVC multi-chambered frame with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, TPV / EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers .

(weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Kommerling, Fenesta & Deceuninck Make)

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 104 x 49 mm & sash 37 x 61 mm both having wall thickness of 2.2 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window above 1.25 sqm upto 3.0 sqm). (Kommerling, Fenesta & Deceuninck Make)

Providing and fixing factory made uPVC white colour french door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with frame 1.60 ± 0.2 mm & sash 2.0 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, TPV / EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners,

mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Kommerling, Fenesta & Deceuninck Make)

French door with 3D hinges made of (big series) frame 58 x 69 mm & sash 58 x 93 mm both having wall thickness of 2.2 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of door above 2.50 sqm upto 3.50 sqm). (Kommerling, Fenesta & Deceuninck Make)

1. Providing and fixing of Sukri / Shakti mat / Godrej brand non-metallic asbestos free composite fire cum smoke check door frame of 55mm thick shutter for 2 hrs. fire rating door system duly tested for Stability , Integrity and Insulation criteria clause 9.4 as per IS 3614 Part – 2 and BS 476 Part 22, for single and double leaf doors tested from CBRI Roorkee with Hardwood Door Frame (Red Merrantti) of section 145mm x 70mm with heat activated in tumescent fire seal strip of size 10mm x 4mm (Astroflame U.K./ Keraflix) and one coat of anti-termite fire retardant polish along with minimum 55mm thick fire / smoke check wooden shutters of 120 minute fire rating comprising of two 9mm thick Starpan / Promat calcium silicate board a 100% without asbestos, brucite and meerschaum having density not more than 950 Kg/M3 and thermal conductivity 0.14 W/m*k sandwiching 31mm thick fire resistance insulation filler coated with FR sealants and faced with 3mm thick decorative ply / 1mm laminate facing on both sides and of approved make with heat activated in tumescent fire seal strips of size 10mm x 4mm (Astroflame U.K./ keraflix) mounted in the grooves of hardwood lipping on three sides except bottom, complete factory finished.

The single/double leaf doors shall be provided with vision panels of minimum size 200 x 400 mm made out of minimum 6mm thick fire rated monolithic, clear glass of 120 min. fire rating from Schott (Germany)/Central /Firelite with complete fire rated gasket channel & moulding beading and filling the gap between moulding /beading and glass with suitable sealant including fixing each shutter with 4 Nos. stainless steel ball bearing hinges 304 grade of size 102mm x 76mm x 3mm with screws. The manufacturer should have tested the entire assembly from CBRI Roorkee along with the required size of fire rated vision panels and approved hardware for 2 hrs. fire rating and shall submit the same for both single leaf and double leaf configurations prior to manufacturing, to the Engineer-in-charge for approval of the agency. One door shall out of the entire lot shall be tested from CBRI Roorkee and the testing charges shall be reimbursed to the contractor on successful submission of the test reports.

The single/double leaf doors shall be provided with vision panels of minimum size 200 x 400 mm made out of minimum 6mm thick fire rated monolithic, clear glass of 120 min. fire rating from Schott (Germany)/Central /Firelite with complete fire rated gasket channel & moulding beading and filling the gap between moulding /beading and glass with suitable sealant including fixing each shutter with 4 Nos. stainless steel ball bearing hinges 304 grade of size 102mm x 76mm x 3mm with screws. The manufacturer should have tested the entire assembly from CBRI Roorkee along with the required size of fire rated vision panels and approved hardware for 2 hrs. fire rating and shall submit the same for both single leaf and double leaf configurations prior to manufacturing, to the Engineer-in-charge for approval of the agency. One door shall out of the entire lot shall be tested from CBRI Roorkee and the testing charges shall be reimbursed to the contractor on successful submission of the test reports.

Supply and fixing of 2 hrs. fire rated CBRI tested as per IS 3614 Part -2 and BS 476 Part-22 stainless steel 304 grade fire rated ball bearing hinges of size 102mm x 76mm x 3mm thick from I.R / Dorma BB 4330/ Marshall.

Supply and fixing of 2 hrs. fire rated CBRI tested as per IS 3614 Part -2 and BS 476 Part-22 door closers having rack and pinion mechanism, with standard arm, dual speed control, CE certifier, having 1 year’s mechanical warranty from I.R LCN 1461 / Dorma TS 73 / Marshall MH DC- S- 14003 tested from CBRI Roorkee along with the fire door assembly.

Supply and fixing of 2 hrs. fire rated CBRI tested as per IS 3614 Part -2 and BS 476 Part-22 stainless steel push type panic bars tested as per IS 3614 Part –II and BS 476 Part -22, from I.R Monarch series / Dorma PHA series / Marshall MHPB SS series prior tested from CBRI Roorkee along with the fire door

Supply and fixing of 2 hrs. fire rated CBRI tested as per IS 3614 Part -2 and BS 476 Part-22 stainless still 304 grade Outside Access Device (Trim and Lock) compatible with single and double leaf Panic Bars from IR Monarch Series / Dorma PHA Series / Marshall MH- PB-SS series prior tested from CBRI Roorkee along with fire door.

Supply and fixing of 2hrs. fire rated CBRI tested as per IS 3614 Part -2 and BS 476 Part-22 mortise dead lock with 80mm cylinder having one side key and one side thumb turn operation from I.R Briton EL 2020 series / Dorma 288 series / MHLDL 13002.

Supply and fixing of 2 hrs. fire rated CBRI tested as per IS 3614 Part -2 and BS 476 Part-22 stainless steel D-Type pull handle of size 22mm dia and 300mm long from Dorma TGDI series / IR -Briton / Marshall make.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing, laying, jointing and testing SWR low noise drainage Pipes, conforming to IS 4985:200 of approved make.

110mm dia. Internal diameter

160mm dia. Internal diameter

200mm dia. Internal diameter

Providing and Fixing SWR low noise drainage pasted Fittings (supreme make including fixing jointing and testing etc. complete in all respect to the satisfaction of Architect/Engineer-in-Charge. (For External Sewarge only) (Supreme, Finolex & Astral Make).

i) COUPLER

ii) BEND 45 DEGREE

iii) BEND 87.5 DEGREE

iv) SWEPT TEE

v) DOOR BEND 87.5 DEGREE

vi) DOOR SWEPT TEE

vii) ECCENTRIC REDUCER 110x75mm

viii) P-TRAP LONG 100mm

i) COUPLER

ii) BEND 45 DEGREE

iii) BEND 87.5 DEGREE

iv) SWEPT TEE

v) DOOR BEND 87.5 DEGREE

vi) DOOR SWEPT TEE

i) COUPLER

ii) BEND 45 DEGREE

iii) BEND 87.5 DEGREE

iv) SWEPT TEE

v) DOOR BEND 87.5 DEGREE

vi) DOOR SWEPT TEE

Providing, laying, jointing and testing uPVC quick fit pipes, conforming to IS 4985:2000 having pressure 6.0 kgf/sq.cm of supreme make or approved by Engineer-in-Charge. Including all kind of special IS 4985-2000 (N.S ITEM (For Internal Toilets & vertical stacks only) (Supreme, Finolex & Astral Make).

Providing, laying, jointing and testing uPVC quick fit moulded fittings, conforming to IS 4985:2000 having pressure 6.0 kgf/sq.cm of supreme make or approved by Engineer-in-Charge. Including all kind of special IS 4985-2000 (N.S ITEM) (For Internal Toilets & vertical stacks only) (Supreme, Finolex & Astral Make).

i) COUPLER

ii) ELBOW 45 DEGREE

iii) ELBOW 90 DEGREE

iv) EQUAL TEE

v) END CAP

vi) UNION

i) COUPLER

ii) ELBOW 45 DEGREE

iii) ELBOW 90 DEGREE

iv) EQUAL TEE

v) END CAP

vi) UNION

i) COUPLER

ii) ELBOW 45 DEGREE

iii) ELBOW 90 DEGREE

iv) EQUAL TEE

v) END CAP

vi) UNION

i) COUPLER

ii) ELBOW 90 DEGREE

iii) EQUAL TEE

iv) END CAP

Providing and fixing in position Bib cock with wall flange (model CQT-23047) of Jaquar make o or equivalent with prior approval of Engineerin charge. (N.S ITEM)

Providing & fixing Hand shower (Health faucet) with 1.0m long easy flex tube in chrome finish & wall hook (model no. ALD-565) Jaquar or equivalent with prior approval of Engineerin charge.

Providing and fixing in position two way Bib cock for and hand shower (model CON-041KN) of Jaquar make o or equivalent with prior approval of Engineerin charge. (N.S ITEM)

Providing and fixing in position Angle Valve (model No.CON-059KN) of Jaquar make or approved by Engineer-in-Charge. (N.S ITEM)

Providing and fixing in position European Type Floor Mounted Water Closet (white) Suit of size(mm), (model (No . CNS-WHT-755SN + CNS-WHT-207 of Jaquar make or equivalent as per prior approval of Engineer-in-Charge. (N.S ITEM), complete in all respects

Providing & fixing Wall Hung Basin (model No. CNS-WHT-801) with fixing accessories set size (550x410x195mm) of Jaquar make or equivalent as per prior approval of Engineer-in-Charge., complete in all respect. (NS Item)

Providing and fixing floor drain with jali (pp) as per I.S:14735:1999 marked of Supreme pipes or equivalent with prior approval of Engineerin charge. (N.S ITEM)

Providing and fixing in position Bottle trap (model no.ALD-769L300x190) with internal partition 32mm size with 300mm & 190mm Long wall connections pipes & wall flange and waste coupling(model no.ALD-705L130) 32mm size full thread with 130mm Height of of Jaquar make or equivalent with prior approval of Engineerin charge (N.S ITEM)

Providing & fixing Pillar Cock long neck with 450mm long braided Hose (model No. CQT -23021B) of Jaquar make or equivalent as per prior approval of Engineer-in-Charge., complete in all respect. (NS Item)

Providing and fixing in position Long body Bib cock with wall flange (model no.CON-107KN) of of Jaquar make or equivalent with prior approval of Engineerin charge (N.S ITEM)

Providing and fixing in position Geyser of 60 liters capacity size 925x400(Model VERSA) of Jaquar make or equivalent with prior approval of Engineerin charge. (N.S ITEM)

Providing and fixing in position Central hole basin mixer without popup waste system with 450mm having long braided hoses (model no.CON-167KNB) of jaguar, grohe, kohler make. (N.S ITEM)

Providing and fixing in position 15 mm i/d wall mounted sink cock with swinging casted round shape spout (Model No.CON-347KN) of Jaquar make or equivalent as per prior approval of Engineer-in-Charge. (N.S ITEM)

ELECTRICAL WORKS - LIGHTING FIXURES -Supply, installation, testing and Commissioning of IP 20 15W LED Surface Downlighter CRCA/ PDC housing equipped , Minimun System Lumen 1140 Lumen, CRI <80, 120 Deg Beam Angle, Input Voltage : AC220-240V, 50/60Hz, Operating voltage range 100-300V, High Performance electronic driver ensure Zero Maintenance, High Surge Protection 2.5KV, Average Life L70B50 50000 hrs, Operating Temperature : -10°C to +45°C. Equivalent to Wipro Cat: LE20-491 /Panasonic: PDLM11154P/Philips: SM251C LED16S- 6500 PSU WH

Supply, installation, testing and Commissioning of IP 20 15W LED Recessed Downlighter polycarbonate housing equipped , Minimun System Lumen 1500 Lumen, CRI <80, 120 Deg Beam Angle, Input Voltage : AC220-240V, 50/60Hz, Operating voltage range 100-300V, High Performance electronic driver ensure Zero Maintenance, High Surge Protection 2.5KV, Average Life L70B50 50000 hrs, Operating Temperature : -10°C to +45°C. Equivalent to Wipro Cat: LE20-491 /Panasonic: PDLM12154/Philips: DN 394B LED16S-6500

Supply, installation, testing and Commissioning of IP 65 40W LED Batten with inbuilt heat sink, polycarbonate housing equipped , Minimun System Lumen 4400 Lumen, CRI <80, 120 Deg Beam Angle, Input Voltage : AC220-240V, 50/60Hz, Operating voltage range 100-300V, High Performance electronic driver ensure Zero Maintenance, High Surge Protection 4KV, Average Life L70B50 50000 hrs, Operating Temperature : -10°C to +45°C. Equivalent to Wipro Cat: LE20-491 /Panasonic: PBTM05407/Philips: WT550C LED 40S

Supply, installation, testing and Commissioning of IP 20 25W LED Linear recess mounting luminaire equipped with Extruded Aluminium housing , High transmittance PMMA diffuser for glare-free symmetric light distribution, Minimun System Lumen 2500 Lumen, CRI <80, 120 Deg Beam Angle, Input Voltage : AC220-240V, 50/60Hz, Operating voltage range 100-300V, High Performance electronic driver ensure Zero Maintenance, High Surge Protection 4KV, Average Life L70B50 50000 hrs, Operating Temperature : -10°C to +45°C. Equivalent to Panasonic Cat: PLRM01254/Philips: RC780B LED26S-6500 PSU W7L120 OD SI/Wipro: LM30-401-XXX-57-XX

Supply, installation, testing and Commissioning of IP 20 25W LED backlit type recess mounting LED luminaire equipped with CRCA housing , High transmittance PMMA diffuser for glare-free symmetric light distribution, Minimun System Lumen 2500 Lumen, CRI <80, 120 Deg Beam Angle, Input Voltage : AC220-240V, 50/60Hz, Operating voltage range 100-300V, High Performance electronic driver ensure Zero Maintenance, High Surge Protection 2.5KV, Average Life L70B50 50000 hrs, Operating Temperature : -10°C to +45°C. Equivalent to Panasonic Cat: PBLM05257/Philips: RC380B LED30S/Wipro: CRCO10R038HP57SLAB

Supply, installation, testing and Commissioning of IP 65 IK 09 10W LED Bulkhead , Minimun System Lumen 4400 Lumen, CRI <80, 120 Deg Beam Angle, Input Voltage : AC220-240V, 50/60Hz, Operating voltage range 100-300V, High Performance electronic driver ensure Zero Maintenance, High Surge Protection 4KV, Average Life L70B50 50000 hrs, Operating Temperature : -10°C to +45°C. Equivalent to Panasonic Cat: PBTM05407/Wipro: LW01-101-XXX-57-XX/ Philips: WT 202

Supply, installation, testing and Commissioning of IP 20 10W LED ultra slim polycarbonate decorative led batten and energy efficient electronic driver, Minimum System Lumen 1000 lumen, CRI <80, 120 Deg Beam Angle, Input Voltage : AC220-240V, 50/60Hz, Operating voltage range 90-300V, High Performance electronic driver ensure Zero Maintenance, High Surge Protection 2.5KV, Average Life L70B50 30000 hrs, Operating Temperature : -10°C to +45°C. Equivalent to Panasonic Cat: PBTM01107/Philips: BN021 LED 10s/Wipro: LL 20

supplying, installation, testing and commissioning of LED strip (flexible) with 60 LEDs per meter, 5.5 W per Meter, 4000K, 600 lumens per meter

Supply, installation, testing and Commissioning of COB LED downlight with die cast aluminium housing in white powder coating finish 7 watt with 24 deg reflection Panasonic PDLM07073 or eqv.

Supply, installation, testing and Commissioning of aluminium extruded Strapline Recessed Linear 12 watt 1200 mm 4000 K of Legero make or eqv.

Supply, installation, testing and Commissioning of 15 watt wall light as approved.

FANS AND EXHAUST FANS - Supplying, Installation, testing and commissioning of Exhaust fans/ wall fan/Ceiling Fans of following sizes including making the holes to suit the size of the fan and making good the damages, including providing and fixing of louvers/shutters, connection, testing and commissioning:-

Ceiling Fan 1200 mm white color 5 Star Rated Specifications Havells ES Plus or eq. , Usha, Orient, Crompton

Exhaust Fan 300 mm Heavy Duty Havells, Usha, Orient, Crompton

Exhaust Fan 380 mm Heavy Duty Havells, Usha, Orient, Crompton

STRUCTURED CABLING SYSTEM PASSIVE -Supplying, installing, testing and commissioning of Cat 6 , Tool less Information outlet for Data & Voice. Cat6 U/UTP built in crimping hands-free, minimum 5 times reconnection possibilities. LCS2 Toolless RJ45 Information outlet where insertion test (in & out) must be 2500 times (I/O) along with front side Label holded and transparent shutter for projection Arteor category white in colour, including front plate and anodised GI box in concealed manner of adequate sizes, including all fixing accessories.

Same as above but RJ 11 information outlet for voice

T V Point Outlet-- Model- Myrius -Legrand - Single Module

Supplying, installing, testing and commissioning of 24 port Cat 6 patch panels available with block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6 U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less connector U/UTP unit in a block.

Supply , Installtion , Testing and comissioning of 12U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts .

LT PANELS -Supply, installation, testing and commissioning of LT panels as per boq enclosed :

Vertical DB 6 Way with MCCB Incomer Legrand - VTPN DB with Metal Doors DPX 160 MCCB DB

CABLES Supplying and laying of following 1.1 kV cables/flexible copper cables in existing trenches/ pipes

4 core 6 sq mm PVC Copper Armoured Cable

CABLE TRAYS -Supplying and installation of 1.6 mm thick powder coated perforated cable tray of following sizes. Item includes necessary accessories like bends, tees and reducers and hardware and supports for fixing cable trays-

Powder coated perforated cable tray 40x450x40 mm

Powder coated perforated cable tray 25x200x25 mm

IP CCTV SURVEILLANCE SYSTEMS - Supply, installation, testing & commissioning of IP IR Indoor dome type (15 mtrs)2.1 MP,Progressive scanning,ONVIF conformant, DUAL Stream, Dy namic Range 60 db,Sensitivity color 0.0 lux,nightsense 0.12 lux at minimum 30 IRE, MOTION+ video motion analysis , 3-10 mm IR Corrected lens Hardware enhanced,IP Series of high-performance,PoE (Power-over-Ethernet), 24 VAC and 12 VDC,SNR > 50 dB,-20 ºC to +50 ºC,UL Listed,ONVIF conformant.

Supply, installation, testing & commissioning of of IP IR outdoor bullet type, 2.1 MP ,progressive scan dual Streaming: Dual H.264 and M-JPEG simultaneously, 1080p30 resolution , Auto lens detection (2.8-12 mm) ,compatible with digital video recorder, PoE (Power-over-Ethernet), 24 VAC and 12 VDC ,UL/CE Listed,ONVIF conformant with IP 66 weather proof housing and 30 mtrs IR range.

Supply, installation, testing & commissioning of 32 channel network recorder with 320 Mbps incoming bandwidth , Realtime display for 24 cameras @1080p. Builtin POE switch to supply power to 24 cameras, 4 HDD with 6 TB Each with RAID5 configuration, Two Monitor HDMI Out . three USB Connector. Operating temperature +0°C to +40°C , Operating humidity <93% non-condensing. (Vendor to provide calculation for Hard disk calculation). Note: 1 months storage required.

Supply , Installation , Testing and Commissioning of 6TB Surviellance Hard Disk. Approved Makes: WD /segate /Toshiba/HP

Supply, installation, testing & commissioning of 40" inches 1080p high resolution professional LCD monitor.

Supply , Installtion , Testing and comissioning of 12U wall mount rack with fans , 2 cable managers , satationary shelf, power strip and necessary hardware. Approved Make List :- Legrand /Rittal /Deliyod

Supplying, installing, testing and commissioning of 16 port Cat 6 patch panels available with block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6 U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less connector U/UTP unit in a block. Approved Make List :- Legrand /Panduit /Siemon.

Supply , Installtion , Testing and comissioning of 4 Feet : CAT6 UTP 23 AWG Patch Cord - 1 mtr - Rack End. Factory crimped LCS2 Patch cord in Blue colour . Approved Make List :- Legrand /Panduit /Siemon.

Supply , Installtion , Testing and comissioning of 7 Feet : CAT6 UTP 23 AWG Patch Cord - 1 mtr - Rack End. Factory crimped LCS2 Patch cord in Blue colour. Approved Make List :- Legrand /Panduit /Siemon.

Supply , Installation , Testing and Commissioning of 16 port L2 Managed switch having port density 16 Nos. of 10M/100M/1G RJ45 Port POE/POE+ ports , 4 Nos. of 1G/10G SFP+ Port , 1X console port , Available POE power 370 W , 128 Gbps switching bandwidth , 32K MAC address support , Support L2 feature STP, RSTP ,MSTP . Support 802.1Q VLAN , port based VLAN , 4K VLAN entries , MAC based VLAN , IP subnet based VLAN . Support IEEE 802.3ad LACP . L3 features - static routing , DHCP server , Device Management system - topology view , floor view , map view , dashboard , traffic monitoring , cable diagnostics.CE,FCC certified Approved Make :Cisco/ Impulse / Juniper / Extreme/ Nexxus

Supply , Installation , Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest. Approved Makes: HP / DELL / IBM / LENOVO

FIRE ALARM SYSTEM - Supply, Installation, Testing and commissioning of EN54 and LPCB approved 1 Loop Microprocessor based Networkable Analogue Addressable Fire Alarm Control panel with 6x40 characters, blue liquid crystal display with backlight illumination, in - built charging facility and 2x12V/7AH batteries. The control Panel shall be configurable by keypad and PC, shall have RS-485 and USB ports. The control panel shall have 2 output souder circuits and shall be able to networking up to 16 loops.

Supply, installation, testing and commissioning of EN54-7 and LPCB approved Analouge Addressable Smoke Detector with base which is fully compatible with analogue addressable protocol, supporting hard addressing.

Supply, installation, testing and commissioning of EN54-5 and LPCB approved Addressable Rate of rise Heat Detector which is fully compatible with analogue addressable protocol, supporting hard addressing.

Supply, installation, testing and commissioning of EN54-11 and LPCB approved Analogue addressable, resettable, unbreakable flexible element manual Call point having sintegrated LED and integral loop isolation facility.

Supply, installation, testing and commissioning of addressable Hooter cum strobe

Supply of Control Module/Output Module

Supply of Fault Isolator Module

Response Indicator

FIRE FIGHTING SYSTEM -Providing, laying, jointing, testing and commissioning of following sizes of MS heavy (Class C) pipes conforming to IS-1239 including cutting , threading welding etc. with all accessories like all fittings (standard MS fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer , two coats of Synthetic enamel paint of approved shade over a coat of primer. Prior to application of primer the surface should be cleaned for any dirt, rusts, rough substance etc. Including painting of legends both direction arrow as per the approval of the Project Manager. All pipe includes cost of supporting/fixing on floor / wall /ceiling with clamps,hangers (using anchor fastners), MS angles/ channels of suitable size/specification. support shall be duly painted prior to support/fix pipe .Pipe shall be supported/fixed by the MS angles/channels/U-clamps.

25 mm dia

65 mm dia

80 mm dia

Providing & fixing male/ female screwed end full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated ball & Teflon seat tested to a pressure rating not less than 16 Kg/sqcm with (threaded joints) complete as required.

(Cost shall be inclusive of providing necessary union / flange connection). 25 mm dia

Providing and fixing C.I. Butterfly valve (Body : Grey Cast Iron, shaft : SS, Disc : SG Iron (nickel plated), Liner : HT - EPDM) of approved make with flange, washer, nuts & bolts and PN 16 pressure rating including rubber gasket & painting complete.

80 mm dia

Providing & fixing C.I Wafer type check valve of rating PN 16 rating including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required.

80 mm dia

Providing & fixing swinging type First Aid hose reel in red colour drum with 36 mts long and 20 mm dia heavy duty rubber water hose, 20 mm dia gate gun metal valve stop cock, (IS:778, class - II) terminating with SS coupling & nozzle of 6mm outlet with shut off valve confirming to IS 8090 - 1976 complete with MS socket for tap-off, drum and brackets (including painting) for fixing on wall with anchor fastner, bolts & nuts conforming to IS:884-1985 (Reaffirmed 2000) complete as required.

Providing and fixing Standard firemans axe with heavy rubber handle.

Providing and fixing lockable indoor type fire hose cabinet door fabricated from 40 x 40 x 5 angle iron sections and 16 gauge MS sheet with full 5mm thick front glass door of size 2.1 m x 0.9 m with center opening for fire hose cabinet. with glass.Suitably marked on the outside with the letters "FIRE HOSE" including locking arrangement. All M.S. work to be in Red P.O. colour over appropriate primer. The above item is only for masonary fire station.( Contractor shall be approved sample of door from the Client / PMC )

Providing and fixing C.I.`Y' strainer with bronze perforated sheet basket including rubber gasket, flanges, nuts, bolts and washers, complete as required.

80 mm dia

Providing and fixing dial type Pressure gauge with isolation cock and chrome coated copper pipe on main header Dial diameter 150 mm celebration 0-15/ sq.cm.

Supply, installation, testing & commissioning of electric driven automatic fire booster Pump suitable for automatic operation consisting of the following: Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump. Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump. Common bed plate of fabricated mild steel channel or cast iron type. Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. The pump shall be of the following specifications: Discharge - 450pm Head - 35 m No. of stage preferred - Single Speed RPM - 2900 Material of construction a) Impeller - Bronze b) Casing - C.I. c) Shaft & Shaft Sleeve - SS-410 d) Bearing - Grease Lubicated e) Seal & Make - Mechanical Type of pump - End suction

Supply of Hiwall airconditioner comprising of the evaporating unit and condensing unit with rotary fixes speed compressor suitable for R-32 Gas

Capacity 1.5 TR – 3 Star

Capacity 1.8/2.0 TR - 3 Star

Installation ,Testing and Commissioning of split Unit

Capacity 1/1.5/2TR - Hiwall

Supply & Installation of refrigerant copper piping with 9 mm insulation for Hiwall Split AC Unit

Supply & Installation of control cabling for Splits

Supply & Installation of M.S Stand For Out Door Unit.for Hiwall split unit – 1TR/1.5TR /2TR/3.5TR

Supply & Installation of PVC Condensate drain piping .

Supply & Installation of Stabilizer – 4 KVA

Supply & Installation of Stabilizer – 5 KVA

Cable Tray for Running pipes

Bidder Name

Amount

Rajesh Kumar Batra Contractor

Sh. Virender Singh Lohchab

Sh. Shanker Singh Tomer

JML Construction Pvt. Ltd.

Naresh Kumar Gupta and Co Pvt Ltd

Sh. Shanker Singh Tomer

Naresh Kumar Gupta and Co Pvt Ltd

Rajesh Kumar Batra Contractor

JML Construction Pvt. Ltd.

Sh. Shanker Singh Tomer

JML Construction Pvt. Ltd.

Naresh Kumar Gupta and Co Pvt Ltd

Rajesh Kumar Batra Contractor