PROVN OF TILING, SOAKPIT, WATER COOLER, SCOOTER STAND, GEYSER AND UNIT EQUIPMENT STORE OF CERTAIN UNITS AND SPECIAL REPAIRS UNDER AGE B/R-II OF GE BENGDUBI MIL STN

Amount

SCHEDULE 'A' PART-I (B/R WORKS)

Surface dressing n exc 15 cm deep in soft/ loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n. exc 1.5 m in depth for foundation, etc and getting out in soft / loose soil complete all as specified and directed.

Excavation over areas not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas exceeding 1.5 m but not exceeding 3.0 m deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

Removing excavated material (soil) to a distance exc 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soft / loose soil complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling & mass concrete complete all as specified and directed.

M&L for Boulder filling dry, handpacked tightly, as in wire crate apron bunds (Wire crate measured separately complete all as specified and directed.

M&L Boulder pitching, laid dry, hand packed tightly concrete complete all as specified and directed.

S&F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed.

Spreading and Levelling of sand in layers n exc. 25 cm thick complete all as specified and directed.

M&L Reinforced cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use & Waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), rough finished surface of concrete complete all as specified and directed.

Use & Waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc rough finished surface of concrete complete all as specified and directed.

M&L for TMT bars (Fe-500/ Fe-550D) 10 mm dia & over, cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per item No. 17.00 here-in-before but 8 mm dia bar complete all as specified and directed.

All as per item No. 17.00 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups, spaces and binders complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged in spikes, framed guard bars and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F steel windows with side hung shutters including projection type hinghs with steel handle, and steel pag stay, complete with guard bars, dovetailed or welder complete all as specified and directed.

All as per item No. 21.00 here-in-before but without glazing bars complete all as specified and directed.

S&F for Steel ventilator with top hung shutters including hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

M&L for Damp proof course 40mm thick In cement concrete 1:2:4, type B-0 to horizontal or vertical surfaces with using WPC as per manufacturer instructions including necessary formwork complete all as specified and directed. (Note: WPC shall be measured & paid seperately)

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed.

M&L for Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m complete all as specified and directed.

M&L for Fly ash brick work with old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with fly ash bricks with old size bricks in one brick thick honeycomb walling, built in cement mortar 1:4 complete all as specified and directed.

M&Lfor Fly ash brick work with old size bricks, straight or curved on plan to any radius half brick thick built in In cement mortar 1:4 complete all as specified and directed.

M&L for sand filling under floor or in foundations including watering and consolidation all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 using WPC as per manufacturer's instructions in finishing layer on brick or concrete surfaces finished even & fair complete all as specified and directed. (Note;- WPC will be measured paid seperately as supply only).

M&L for Rendering 15 mm thick on other than fair faces of brick work or concrete surface in cement mortar (1:6) surface finished even & smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20 mm graded crushed stone aggregate in lintel upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, holdfast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified.

M&L for precast RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified.

M&L for preparation of new surface of wall and three coat of white wash on walls complete all as specified and directed.

M&L for two coat of wall care putty on wall including preparation of surface with sand paper etc. to obtain smooth surface complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved tint on wall complete all as specified and directed.

M&L for preparation of newly plastered surfaces and applying two coats of oil emulsion distemper of approved tint over chalk whiting, on plastered surfaces, preparatory to distempering on wall and one coat alkaliresistant priming paint complete all as specified and directed.

M&L for two coats of cement base paint on wall, soffits of chajjas, cornices etc including prepration of plastered/unplastered surfaces complete all as specified and directed.

M&L for prepration of old plastered/unplastered surfaces of wall one coat of cement base paint complete all as specified and directed.

M&L for preparation of new wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as specified and directed.

S&F roof trusses (farmed), trusses purlins, crane gantries, rails and fastenings and heavy bracket framing MS tubes medium grade as in truss, purlin, rafters, post etc fixed with and including angle cleat, MS plate etc including necessary welding, fittings etc Fe-410-W (Gde-E-250 quality-B) complete all as specified and directed.

S&F 0.50 mm thick Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

S&F 0.50 mm thick Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)and similar work conforming to Fe-410- W(Gde- E-250) quality- B complete as specified and directed.

S&F Decorated PVC False ceiling of size 600mmX600mmX5mm thick (±0.25) plain PVC sheet of 600 Kg/Cum density manufactured by an ISO-9000 certified company, used as a panel insert in a frame work made using anodized aluminum powder coated T-section of size 25mmX25mm of 19 gauge or 1mm thick in square pattern of grid size 6000mmX600mm. The aluminum frame work is supported from the ceiling with the help of J Hook or 4 mm GI wire of required size to maintain the proper levels etc. The aluminum frame work is supported on side wall with the use of aluminum L section of size 25mmX25mm of 19 gauge or 1mm thick angles etc. complete all as specified and directed.

M&L for hardcore of gauge not exc. 63mm, deposited, spread and levelling in layers not exc. 15 cm thick, watered and rammed to true surface with broken stone or boulder complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protections, finished even and smooth w/o using extra cement with joints 10 mm wide and in full depth at corners and @ 3.0 m c/c filled with mastic mortar complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc1.5 sqm each complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles all as directed.

Taking down cement plaster any description on brick or stone walls including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Demolition cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings in roof coverings/ ridge all as directed.

Dismantling frame work timber scantlings 40 sq. cm and over in section, in any position all as directed.

All as per item No 57.00 here-in-before but fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as directed.

S&F Pressed steel frames frame size 165X60mm for doors with one or moe rebates including necessory fixing lugs, hinges, lock strike plates etc, complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) etc complete all as specified and as directed

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel designed with 2mm thick moulded pre-laminated PVC sheet on the front face & 2mm plain colour PVC sheet on back face including suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F of 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 2nd class HW glazed and skeleton 30 mm thick door/window shutters open rebated and prepared to receive glass, gauze etc with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sites of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (b) complete all as specified and directed.

S&F 75mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F100mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 100 mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 3.00 mm thicksheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F 3.00 mm thick figure glass, pin head type and glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc including brushing with neat cement slurry @ 3 kg of cement per Sq. metre all as specified and directed.

M&L cement concrete 75 mm thick 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed.

M&L cement concrete as in flooring 25 mm thick 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) finished surface even and rough for receiving floor finishes complete all as specified and directed.

M&L cement concrete as in flooring 40 mm thick 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) size 400mm x 400mm, in floors etc. set over 15mm thick screed in cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for coloured glazed ceramic tiles 300x450mm size 7mm thick premium quality coforming to relevant IS as on dado incl 10mm thick plastering in CM(1:3) set jointed in neat cement slurry and pointed with colour cement to match the tiles on dado /skirting complete all as specified and directed.

M&L for vitrified ceramic tiles 7 to 9mm thick, light shade (squares/rectangular) polished, area of each tile exceeding 0.06 sqm but not exceeding 0.36 sqm, in floors etc. set over 15mm thick screed in cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

ditto all as per item no 80.00 above but in skirting including 10mm thick plasrer in cement mortar(1:4) complete all as specified and directed.

M&L for polished, machine cut, kota stone slab flooring 20-25mm thick over 20 mm thick cement screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including including rubbing and polishing complete all as specified and directed.

ditto all as per item no 82.00 above but in skirting including 10mm thick plasrer in cement mortar(1:3) complete all as specified and directed.

Demolition / breaking up damaged SGSW pipe of any position and of internal dia of pipe 100 mm including demolition of PCC, and removing dismantled material where directed at a distance n exc 50 m complete all as specified and directed.

M&L for Salt glazed stone ware (SGSW) drain pipes laid in trenches and jointed as specified in 150mm internal dia of pipe grade 'A' complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-2 (Using 40mm graded crushed stone aggregates) as in bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore complete all as specified and directed.

S&F 50mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trances or in floors complete all as specified and as directed.

S&F 75mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trances or in floors complete all as specified and as directed.

S&F 110mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trances or in floors complete all as specified and as directed.

S&F 100mm bore Cast iron soil sand cast pipe, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors, complete all as specified and directed.

M&L for Salt glazed stone ware (SGSW) drain pipes laid in trenches and jointed as specified in 150mm internal dia of pipe grade 'A' complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified.

S&F PVC (SWR) Bends (any radius), diminishing pieces or tapers, bore of pipe 110mm, complete all as specified.

S&F PVC (SWR) vent cowl bore of pipe 50mm, complete all as specified.

S&F CI vent cowl bore of pipe 100mm, complete all as specified.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

S&F in repairs vitreous china wash hand basin flat back basin white size 550x400mm with counter sunk type including CP waste coupling 32mm bore, wase pipe 32mm bore, 750 long etc a pair of MS bracket and cutting for pinning in ends of brackets, waste chain & plug and porcelain stopper complete all as specified and directed.

S&F in repairs vitreous china wash down water closet European type (pedestal pattern) white (Excluding flushing cistern & flush pipe) including plastic water closet seat white, conncetion to out going pipe and flushing pipe complete all as specified and directed.

S&F in repairs vitreous china wash down water closet European type (pedestal pattern)size 580mm x 440mm white (Excluding flushing cistern & flush pipe) including brass CP trap 'P' or 'S' pattern with inlet and outlet intergral foot rests complete all as specified and directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern low level, white, with inlet, ball valve,float and handle including brackets capacity 10 ltr complete all as specified and directed.

S&F in repairs PVC connection 15mm bore with 2 nos PTMT nuts 45cm long fixed with all as directed.

S&F in repairs PVC connection 15mm bore with 2 nos PTMT nuts 30cm long fixed with all as directed.

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 15 mm dia bore complete all as specified and as directed

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 20 mm dia bore complete all as specified and as directed

S&F MS tubes, 'medium grade' ISI marked galvanised 15mm bore, with all fitting and fixed complete to walls and ceilings or laid in floors/laid in trenches complete all as specified and directed.

S&F MS tubes, 'medium grade' ISI marked galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, 20mm bore complete all as specified and directed.

S&F in repairs CP brass shower rose 125 mm dia with or without swivel joints, including fixing to steel pipe or union complete all as specified.

S&F rotational moulded polyethene water storage tank 500 ltrs capacity (cylindrical vertical with closed top) double-layered including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc including dismanteling water tanks, two coat of white silicon paint complete all as specified and as directed.

S&F rotational moulded polyethene water storage tank 1000 ltrs capacity (cylindrical vertical with closed top) double-layered including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc including dismanteling water tanks, two coat of white silicon paint complete all as specified and as directed.

S&F stop cock 15mm bore, cast copper, fancy type, chromium plated, long body with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs Pillar taps, 15mm bore dia of pipe cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F In repairs Bib taps, 15mm bore cast copper alloy, fancy type, chromium plated with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F grating doom 100mm dia of PTMT (minimum weight 25gms) complete all as specified and directed.

S&F PVC waste pipe, 32mm bore, 750mm long complete all as specified and directed.

S&F in repairs wall mixture with provision for overhead shower with 115mm ling bend pipe on upper side, connecting legs and wall flange of 15mm bore complete all as specified and directed. Make Jaquar Cat No. FUS-29273UPR or equivalent.

S&F CP tubular towel rail 600 mm long and 20mm dia icluding brackets etc complete all as specified and as directed.

M&L Reinforced cement concrete 1:1.5:3 type A-1 using 20 mm graded crushed stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for broken bricks loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed.

SCHEDULE 'A' PART-II (E/M WORKS)

Taking down carefully copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed.

Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse) complete all as specified and as directed.

M & L for concealed point wiring One light point/one fan/light/exjaust/bell point controlled by one switch with FRLS PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 sqmm size alongwith one earth continuity conductor with FRLS PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface all as specified and directed.

All as per item No 123.00 here-in-before but One 3 pin socket outlet, 5 Amp on independent board all as specified and directed.

All as per item No 123.00 here-in-before but One 3 pin socket outlet, 5 Amp on same board all as specified and directed.

All as per item No 123.00 here-in-before but for one 15 Amp 3 pin switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire complete all as specified and as directed.

S&F Socket outlet multipurpose 3 pin, 15 Amp and 3 pin 6 Amp controlled by one switch complete all as specified and directed.

S&F Switch piano, flush button type, single pole, one way 5 Amp complete all as specified and directed.

S&F Socket outlet 5 pin, 6 Amp flush type complete all as specified and directed.

S&F ceiling rose surface bakelite three terminals complete all as specified and as directed.

S&F decorative lamp holder insulated body with LED lamp 5 Watt suitable for batten fitting complete all as specified and as directed.

S&F LED Neo tube light fitting 1x 18W, 230 V, with tube 4 feet wall mounted LED batten ultra bright LED polycarbonate tubelight with very high efficency suitedfor installation existing T8 tubelight with G13 lamp holders to give glare free light complete all as specified and as directed. (Make Crompton/ Havells/ Bajjaj/ Philips)

M&L for sub main wiring with 2 run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 2.5 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 2.5 sqmm as earth continuity conductor drawn through PVC conduit 25mm dia ISI marked complete all as specified and directed. Note :- (a) PVC Conduit shall be included in same rate. (b) For concealed sub-main wiring cutting chases shall be included in rate. (c) All the incomming and outgoing cable should be connected throgh proper lugs & sockets as per site requirement)

S&F Building security LED light luminaire fitting 1X20 W and including cable for connection from celling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1m long bent to shape including bolt, nut,washer,clam made out of MS flat of size 25X3 mm, 4 nos Anchor Bolt of suitable size etc all as specified and as directed. Make : CG MODEL LST 20 CDL/ SURYA MODEL SLE UL 20 W IP66 LXN.

S&F sheet metal enclosure for MCCB, DBs, phosphatised, powder coated, single pole and neutral (SPN) 240 volt, double door, suitable for 4 way with dim rail earth and neutral bar complete all as specified and directed.

S&F sheet metal enclosure for MCCB, DBs, phosphatised, powder coated, single pole and neutral (SPN) 240 volt, double door, suitable for 8 way with dim rail earth and neutral bar complete all as specified and directed.

S&F MCB double pole upto 32 Amps, breaking capacity 10KA, 240 Volts 'C' curve all as specified and directed.

S&F MCB single pole upto 32 Amps, breaking capacity 10KA, 240 Volts 'C' curve all as specified and directed.

S&F in replacement Exhaust Fan of Size 380mm sweep, 230Volts AC, with louver shutter including cutting of hole in wall of suitable size and connection from existing ceiling rose to fan complete all as specified and directed.

Material and labour for XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 2 core laid in trench /poles/on wall complete all as specified and directed.

Supply, install, testing & commissioning of water cooler storage type, ISI marked, 5 star rated, electric driven 230V, 50 Hz, single phase supply with all internal accessories, stainless steel body & tank, power saving PUF insulation, adjustable cold water thermostat, 10 degree to 25 degree centigrade, auto cut-off facility, over-load protection, stainless steel front panel, extended plastic legs, eco-friendly confirming to relevant IS & power factor shall not be less than 0.85 compressor & approx storage capacity of 120 Ltrs & nominal cooling capacity of 60 Ltrs incl electric & water connection complete all as specified and as directed.

Supply, install, testing & commissioning of water cooler storage type, ISI marked, 5 star rated, electric driven 230V, 50 Hz, single phase supply with all internal accessories, stainless steel body & tank, power saving PUF insulation, adjustable cold water thermostat, 10 degree to 25 degree centigrade, auto cut-off facility, over-load protection, stainless steel front panel, extended plastic legs, eco-friendly confirming to relevant IS & power factor shall not be less than 0.85 compressor & approx storage capacity of 80 Ltrs & nominal cooling capacity of 40 Ltrs incl electric & water connection complete all as specified and as directed.

S&F MS tubes, 'medium grade' ISI marked galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, 25mm bore complete all as specified and directed.

Cutting existing steel tubing for alterations or additions Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) of size 40 to 50mm bore complete all as specified and directed.

Cutting existing steel tubing for alterations or additions Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) of size 15mm bore complete all as specified and directed.

M&L sand cushioning (dry) in trenches for protection of UG cables (below, above and around the cable laid in trenches) of 230mm spreding thickness and consolidated (punned) upto 180mm thickness complete all as specified and directed.

Material and labour for well burnt bricks, Sub class 'B' bricks, best quality locally available laid flat, dry in trenches for cable protection complete all as specified and directed.

M&L for Advance Maintenance Free G.I. SAFE EARTHING Electrode with PIPE of not less than 50 mm outer dia( THICKNESS NOT LESS THAN -2.5MM) and two meter length, The electrode should be of galvinised (80 -100 micron) along with earth lead as Galvanised steel strip of size 32 X6 mm 7.5 m . The GI Electrode shall be pre-filled with Cristaline Conductive Material (CCM) . The GI electrode shall be surrounded with 25 kg BackFill compound to provide maximum contact between the electrode and Back Fill Compound. Backfill compound should be eco-frendly and having RoHs certification . GI Electrode Shall be tested from CPRI.The earting pit should be cover with PCC (1:2:4, type B-1) cover ,of 450 x 450 mm complete all as specified and directed. (Make: ASHLOK / INDELEC / JMV / TERCEL).

M&L for flame proof concealed point wiring for one fan point controlled by one switch with 1.5 sqmm FRLS PVC insulated unsheathed single core multi-stranded copper conductor cable 1100 volt grade drawn through and including (medium grade) stove enamelled steel conduit in concealed of suitable dia alongwith 1.5 sqmm continuous FRLS PVC insulated unsheathed single core multi-stranded copper conductor cable for earth continuity wire, connected to earth dolly and to be terminated in control gear box/ flame proof switch with flame proof junction box including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface all as specified and directed.

M&L for flame proof concealed point wiring for 15 Amp switch socket outlet independent with 2.5 sqmm FRLS PVC insulated unsheathed single core multi-stranded copper conductor cable 1100 volt grade drawn through and including (medium grade) stove enamelled steel conduit in concealed of suitable dia alongwith 2.5 sqmm continuous FRLS PVC insulated unsheathed single core multi-stranded copper conductor cable for earth continuity wire, connected to earth dolly and to be terminated in control gear box/ flame proof switch with flame proof junction box including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface all as specified and directed.

S&F switch flame proof rotary type with termination box in LM6, 16A single pole 250 V complete all as specified and directed.

Supply and fixing Flame proof switch socket & plug combined in LM6 cable termination box in LM 6, 16 A 250 V, 2p+Earth complete all as specified and as directed.

S&F CMRI certified LED flame proof fitting 1x20 watts, IP 65, FLP-WP made of aluminium alloy LM6, with electronic ballast, bipin holders, connector blocks, tube rod etc. complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Make : CG MODEL EXTN2LT8/ Sudhir or equivalent make Philips/ Bajaj /Surya as specified.

S&F CMRI certified LED flame proof bulkhead lumanarie recommended for gas/vapour group-IIA & IIB and Zone-1&2, IP65 complete all as specified and as directed. Make : CG MODEL Glare Pro cat part No. FWL1315-30-CDL or equivalent make Philips/ Bajaj /Surya as specified.

Supply and fixing Flame proof FLP-WP sheet metal enclosure for MCB, DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 8 way with dim rail earth and neutral bar complete all as specified and as directed.

M&L for sub main wiring with 2 run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4 sqmm as earth continuity conductor drawn through PVC conduit 25mm dia ISI marked complete all as specified and directed. Note :- (a) PVC Conduit shall be included in same rate. (b) For concealed sub-main wiring cutting chases shall be included in rate. (c) All the incomming and outgoing cable should be connected throgh proper lugs & sockets as per site requirement)

Supply and fixing water heater (Geyser) storage type BEE 5 star rated AC 230 Volts of capacity 25 litres with Grounding of 4 Nut and Bolts,gasket and CP connecting pipe for outlet and inlet water from geyser complete all as specified and directed. Make V-Guard/ Havells/ Racold/BAJAJ/USHA.

S&F single pole and neutral enclosure with a two pin and earth plug socket with double pole one MCB of upto 20 amp complete all as specified and directed.

S&F Sheet metal enclosure for MCB, DBs, phosphatised, power coated, double door single pole & Neutral 4 way with din rail earth and neutral bar at complete all as specified and directed.

S&F MCB double pole 40 Amps, breaking capacity 10KA, 240 Volts 'C' curve all as specified and directed.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 10846.35 (refer Tender Srl Page No 40). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

M/S BOSE CONSTRUCTION

M/S R. K. INDUSTRIES

Paritosh Saha

CHAKRABORTY AND SONS

MS ESSCON